Design of an indirectly fired gas turbine integrated with an organic rankine cycle unit for combined heat and power production

In the last years, the European countries have paid increasing attention to renewable sources and greenhouse emissions. The Council of the European Union and the European Parliament have established ambitious targets for the next years. In this scenario, biomass plays a prominent role since its life cycle produces a zero net carbon dioxide emission. Additionally, biomass can ensure plant operation continuity thanks to its availability and storage ability. Several conventional systems running on biomass are available at the moment. Most of them are performant either in the large-scale or in the small power range. The absence of an efficient system on the small-middle scale inspired this thesis project. The object is an innovative plant based on a wet indirectly fired gas turbine (WIFGT) integrated with an organic Rankine cycle (ORC) unit for combined heat and power production. The WIFGT is a performant system in the small-middle power range; the ORC cycle is capable of giving value to low-temperature heat sources. Their integration is investigated in this thesis with the aim of carrying out a preliminary design of the components. The targeted plant output is around 200 kW in order not to need a wide cultivation area and to avoid biomass shipping. Existing in-house simulation tools are used: They are adapted to this purpose. Firstly the WIFGT + ORC model is built; Zero-dimensional models of heat exchangers, compressor, turbines, furnace, dryer and pump are used. Different fluids are selected but toluene and benzene turn out to be the most suitable. In the indirectly fired gas turbine a pressure ratio around 4 leads to the highest efficiency. From the thermodynamic analysis the system shows an electric efficiency of 38%, outdoing other conventional plants in the same power range. The combined plant is designed to recover thermal energy: Water is used as coolant in the condenser. It is heated from 60°C up to 90°C, ensuring the possibility of space heating. Mono-dimensional models are used to design the heat exchange equipment. Different types of heat exchangers are chosen depending on the working temperature. A finned-plate heat exchanger is selected for the WIFGT heat transfer equipment due to the high temperature, oxidizing and corrosive environment. A once-through boiler with finned tubes is chosen to vaporize the organic fluid in the ORC. A plate heat exchanger is chosen for the condenser and recuperator. A quasi-monodimensional model for single-stage axial turbine is implemented to design both the WIFGT and the ORC turbine. The system simulation after the components design shows an electric efficiency around 34% with a decrease by 10% compared to the zero-dimensional analysis. The work exhibits the system potentiality compared to the existing plants from both technical and economic point of view.

Modeling of diesel particulate filter filtration and regeneration for transient driving schedules

Due to their high thermal efficiency, diesel engines have excellent fuel economy and have been widely used as a power source for many vehicles. Diesel engines emit less greenhouse gases (carbon dioxide) compared with gasoline engines. However, diesel engines emit large amounts of particulate matter (PM) which can imperil human health. The best way to reduce the particulate matter is by using the Diesel Particulate Filter (DPF) system which consists of a wall-flow monolith which can trap particulates, and the DPF can be periodically regenerated to remove the collected particulates. The estimation of the PM mass accumulated in the DPF and total pressure drop across the filter are very important in order to determine when to carry out the active regeneration for the DPF. In this project, by developing a filtration model and a pressure drop model, we can estimate the PM mass and the total pressure drop, then, these two models can be linked with a regeneration model which has been developed previously to predict when to regenerate the filter. There results of this project were: 1 Reproduce a filtration model and simulate the processes of filtration. By studying the deep bed filtration and cake filtration, stages and quantity of mass accumulated in the DPF can be estimated. It was found that the filtration efficiency increases faster during the deep-bed filtration than that during the cake filtration. A “unit collector” theory was used in our filtration model which can explain the mechanism of the filtration very well. 2 Perform a parametric study on the pressure drop model for changes in engine exhaust flow rate, deposit layer thickness, and inlet temperature. It was found that there are five primary variables impacting the pressure drop in the DPF which are temperature gradient along the channel, deposit layer thickness, deposit layer permeability, wall thickness, and wall permeability. 3 Link the filtration model and the pressure drop model with the regeneration model to determine the time to carry out the regeneration of the DPF. It was found that the regeneration should be initiated when the cake layer is at a certain thickness, since a cake layer with either too big or too small an amount of particulates will need more thermal energy to reach a higher regeneration efficiency. 4 Formulate diesel particulate trap regeneration strategies for real world driving conditions to find out the best desirable conditions for DPF regeneration. It was found that the regeneration should be initiated when the vehicle’s speed is high and during which there should not be any stops from the vehicle. Moreover, the regeneration duration is about 120 seconds and the inlet temperature for the regeneration is 710K.

Analysis of a novel waste heat recovery mechanism for an I.C. engine

Typical internal combustion engines lose about 75% of the fuel energy through the engine coolant, exhaust and surface radiation. Most of the heat generated comes from converting the chemical energy in the fuel to mechanical energy and in turn thermal energy is produced. In general, the thermal energy is unutilized and thus wasted. This report describes the analysis of a novel waste heat recovery (WHR) system that operates on a Rankine cycle. This novel WHR system consists of a second piston within the existing piston to reduce losses associated with compression and exhaust strokes in a four-cycle engine. The wasted thermal energy recovered from the coolant and exhaust systems generate a high temperature and high pressure working fluid which is used to power the modified piston assembly. Cycle simulation shows that a large, stationary natural gas spark ignition engine produces enough waste heat to operate the novel WHR system. With the use of this system, the stationary gas compression ignition engine running at 900 RPM and full load had a net increase of 177.03 kW (240.7 HP). This increase in power improved the brake fuel conversion efficiency by 4.53%.

Laser Thomson scattering measurements of electron temperature and density in a Hall-effect plasma

Hall-effect thrusters (HETs) are compact electric propulsion devices with high specific impulse used for a variety of space propulsion applications. HET technology is well developed but the electron properties in the discharge are not completely understood, mainly due to the difficulty involved in performing accurate measurements in the discharge. Measurements of electron temperature and density have been performed using electrostatic probes, but presence of the probes can significantly disrupt thruster operation, and thus alter the electron temperature and density. While fast-probe studies have expanded understanding of HET discharges, a non-invasive method of measuring the electron temperature and density in the plasma is highly desirable. An alternative to electrostatic probes is a non-perturbing laser diagnostic technique that measures Thomson scattering from the plasma. Thomson scattering is the process by which photons are elastically scattered from the free electrons in a plasma. Since the electrons have thermal energy their motion causes a Doppler shift in the scattered photons that is proportional to their velocity. Like electrostatic probes, laser Thomson scattering (LTS) can be used to determine the temperature and density of free electrons in the plasma. Since Thomson scattering measures the electron velocity distribution function directly no assumptions of the plasma conditions are required, allowing accurate measurements in anisotropic and non-Maxwellian plasmas. LTS requires a complicated measurement apparatus, but has the potential to provide accurate, non-perturbing measurements of electron temperature and density in HET discharges. In order to assess the feasibility of LTS diagnostics on HETs non-invasive measurements of electron temperature and density in the near-field plume of a Hall thruster were performed using a custom built laser Thomson scattering diagnostic. Laser measurements were processed using a maximum likelihood estimation method and results were compared to conventional electrostatic double probe measurements performed at the same thruster conditions. Electron temperature was found to range from approximately 1 – 40 eV and density ranged from approximately 1.0 x 1017 m-3 to 1.3 x 1018 m-3 over discharge voltages from 250 to 450 V and mass flow rates of 40 to 80 SCCM using xenon propellant.

Proteins in silico-modeling and sampling

Proteins are linear chain molecules made out of amino acids. Only when they fold to their native states, they become functional. This dissertation aims to model the solvent (environment) effect and to develop & implement enhanced sampling methods that enable a reliable study of the protein folding problem in silico. We have developed an enhanced solvation model based on the solution to the Poisson-Boltzmann equation in order to describe the solvent effect. Following the quantum mechanical Polarizable Continuum Model (PCM), we decomposed net solvation free energy into three physical terms– Polarization, Dispersion and Cavitation. All the terms were implemented, analyzed and parametrized individually to obtain a high level of accuracy. In order to describe the thermodynamics of proteins, their conformational space needs to be sampled thoroughly. Simulations of proteins are hampered by slow relaxation due to their rugged free-energy landscape, with the barriers between minima being higher than the thermal energy at physiological temperatures. In order to overcome this problem a number of approaches have been proposed of which replica exchange method (REM) is the most popular. In this dissertation we describe a new variant of canonical replica exchange method in the context of molecular dynamic simulation. The advantage of this new method is the easily tunable high acceptance rate for the replica exchange. We call our method Microcanonical Replica Exchange Molecular Dynamic (MREMD). We have described the theoretical frame work, comment on its actual implementation, and its application to Trp-cage mini-protein in implicit solvent. We have been able to correctly predict the folding thermodynamics of this protein using our approach.

Development of room temperature operating single electron transistor using FIB etching and deposition technology

The single-electron transistor (SET) is one of the best candidates for future nano electronic circuits because of its ultralow power consumption, small size and unique functionality. SET devices operate on the principle of Coulomb blockade, which is more prominent at dimensions of a few nano meters. Typically, the SET device consists of two capacitively coupled ultra-small tunnel junctions with a nano island between them. In order to observe the Coulomb blockade effects in a SET device the charging energy of the device has to be greater that the thermal energy. This condition limits the operation of most of the existing SET devices to cryogenic temperatures. Room temperature operation of SET devices requires sub-10nm nano-islands due to the inverse dependence of charging energy on the radius of the conducting nano-island. Fabrication of sub-10nm structures using lithography processes is still a technological challenge. In the present investigation, Focused Ion Beam based etch and deposition technology is used to fabricate single electron transistors devices operating at room temperature. The SET device incorporates an array of tungsten nano-islands with an average diameter of 8nm. The fabricated devices are characterized at room temperature and clear Coulomb blockade and Coulomb oscillations are observed. An improvement in the resolution limitation of the FIB etching process is demonstrated by optimizing the thickness of the active layer. SET devices with structural and topological variation are developed to explore their impact on the behavior of the device. The threshold voltage of the device was minimized to ~500mV by minimizing the source-drain gap of the device to 17nm. Vertical source and drain terminals are fabricated to realize single-dot based SET device. A unique process flow is developed to fabricate Si dot based SET devices for better gate controllability in the device characteristic. The device vi parameters of the fabricated devices are extracted by using a conductance model. Finally, characteristic of these devices are validated with the simulated data from theoretical modeling.

Production of Ethanol from Hardwood

Diminishing crude oil and natural gas supplies, along with concern about greenhouse gas are major driving forces in the search for efficient renewable energy sources. The conversion of lignocellulosic biomass to energy and useful chemicals is a component of the solution. Ethanol is most commonly produced by enzymatic hydrolysis of complex carbohydrates to simple sugars followed by fermentation using yeast. C6Hl0O5 + H2O −Enxymes→ C6H12O6 −Yeast→ 2CH3CH2OH + 2C02 In the U.S. corn is the primary starting raw material for commercial ethanol production. However, there is insufficient corn available to meet the future demand for ethanol as a gasoline additive. Consequently a variety of processes are being developed for producing ethanol from biomass; among which is the NREL process for the production of ethanol from white hardwood. The objective of the thesis reported here was to perform a technical economic analysis of the hardwood to ethanol process. In this analysis a Greenfield plant was compared to co-locating the ethanol plant adjacent to a Kraft pulp mill. The advantage of the latter case is that facilities can be shared jointly for ethanol production and for the production of pulp. Preliminary process designs were performed for three cases; a base case size of 2205 dry tons/day of hardwood (52 million gallons of ethanol per year) as well as the two cases of half and double this size. The thermal efficiency of the NREL process was estimated to be approximately 36%; that is about 36% of the thermal energy in the wood is retained in the product ethanol and by-product electrical energy. The discounted cash flow rate of return on investment and the net present value methods of evaluating process alternatives were used to evaluate the economic feasibility of the NREL process. The minimum acceptable discounted cash flow rate of return after taxes was assumed to be 10%. In all of the process alternatives investigated, the dominant cost factors are the capital recovery charges and the cost of wood. The Greenfield NREL process is not economically viable with the cost of producing ethanol varying from $2.58 to $2.08/gallon for the half capacity and double capacity cases respectively. The co-location cases appear more promising due to reductions in capital costs. The most profitable co-location case resulted in a discounted cash flow rate of return improving from 8.5% for the half capacity case to 20.3% for the double capacity case. Due to economy of scale, the investments become more and more profitable as the size of the plant increases. This concept is limited by the amount of wood that can be delivered to the plant on a sustainable basis as well as the demand for ethanol within a reasonable distance of the plant.

Heat flow measurements on METEOR cruise M86/5

Mud volcanoes (MV) are sources of mass and energy, transported from deeper levels of the sediment pile to the surface. Together with fluid and gas, thermal energy is emitted through these structures. Therefore heat flow determination is a sensible tool to detect and quantify the amount of convective flow. In the Gulf of Cadiz several mud volcanoes can be found along major tectonic lines (SWIM faults). We employ geothermal measurements to observe the activity of mud volcanoes and possible leakage at the faults apart from pronounced structures.

Potencial del cultivo de la chumbera (Opuntia ficus-indica (L) Miller) para la obtención de biocombustibles

El presente trabajo trata sobre el potencial del cultivo de chumbera (Opuntia ficus-indica (L) Miller) para la obtención de dos biocombustibles: bioetanol y biogás. Para lograr este objetivo se ha estudiado, por una parte, el empleo de procedimientos orientados a la producción de bioetanol no celulósico a partir de cladodios de chumbera, lo que ha dado como resultado rendimientos de entre 156 y 221 litros de etanol por cada tonelada de materia seca de biomasa, y, por otra, la obtención de biogás mediante la digestión anaeróbica de los mismos en régimen mesófilo, donde se han hallado rendimientos en torno a 198 m3 de metano por tonelada de materia seca. Una vez determinado el potencial de la materia prima se han diseñado procesos para una escala industrial que permitan la transformación de los cladodios de chumbera en ambos biocombustibles y se han determinado sus balances energéticos, los cuales han dado como resultado la autosuficiencia de ambos procesos, obteniéndose, además, un excedente térmico de 1.235 kcal L-1 de etanol producido, y en torno a 140 kep de energía total (térmica + eléctrica) por tonelada de materia seca empleada en la digestión anaeróbica. Por último se ha estimado el potencial de producción de ambos combustibles en un área apta para el cultivo de la chumbera. En concreto, este estudio se ha llevado a cabo para la provincia de Almería, elegida por tratarse de una zona con cierta tradición en el manejo de esta planta y presentar un clima semiárido mediterráneo. La superficie apta para el cultivo de la chumbera en esta provincia se ha estimado en 100.616 ha y el rendimiento medio del cultivo en 5 t MS ha-1 año-1. En el caso del bioetanol esto implicaría un potencial de producción en torno a 82.158 m3 año-1 que podrían dar lugar a la creación de dos macrodestilerías (con una producción de 100.000 L diarios) o de 49 microdestilerías (con 5.000 L diarios de producción). Si se optara por la transformación de la biomasa de chumbera en metano, podrían obtenerse 99,4 M de metros cúbicos, lo cual permitiría el establecimiento de 79 plantas de cogeneración de 500 kW cada una. ABSTRACT The present work deals with the potential of prickly pear (Opuntia ficus-indica (L) Mill.) biomass as a feedstock for bioethanol and biogas. In order to reach this objective different procedures aiming at the production of non-cellulosic bioethanol from cladodes were carried out; yields from156 to 221 litres of bioethanol per ton of dry matter were found. Mesophilic anaerobic digestion of cladodes was also studied and yields around 198 m3 of methane per ton of dry matter were reached. From these results, processes on an industrial scale were designed for both pathways of energy conversion of prickly-pear biomass and the respective energy balances were calculated. They resulted to be self-sufficient from an energetic point of view; the bioethanol pathway generated a thermal energy surplus of 1,235 kcal per litre of ethanol, while around 140 kep of total energy (heat + electricity) were obtained from the anaerobic digestion of one ton of dry cladodes. Finally, the potential production of both biofuels from prickly pear biomass was estimated for a specific area. The province of Almeria was chosen because of its climate conditions and the previous existence of prickly pear plantations. The area suitable for prickly pear cultivation in the province was estimated at a maximum of 100.616 ha, with an average yield of about 5 t DM ha-1 year-1. If prickly pear biomass were cropped for bioethanol in Almeria, the potential production of bioethanol could reach 82,158 m3 year-1, in either two macrodistilleries (100,000 L day-1) or 49 microdestilleries (5,000 L day-1). If the biogas pathway were preferred, 99. 4 Mm3 of methane could be reached and this would represent 79 CHP plants (500 kW each one).

Concentrating solar power technologies. The DESERTEC megaproject

The European strategies on energy have been searching for years to reduce the dependency of Europe from fossil fuels. Underlying this effort, there exist geopolitical, economic, environmental reasons and the reality that oil reservoirs will dry out some day. Renewable energies have become a milestone of this strategy because their huge potential has emerged after years of uncertainty. One of the better developed renewable sources, which is nearer to commercial maturity is solar-thermal energy. In this paper, the current state of this technology will be described as well as the developments that may be expected in the short and mid terms, including the thermoelectric solar megaproject DESERTEC, a German proposal to ensure energy resources to the mayor areas of the EU-MENA countries. The reader will acquire a picture of the current state of the market, of the technical challenges already achieved and of the remaining ones.

Morteros acumuladores con parafinas microencapsuladas para el aprovechamiento de la energía solar en suelos radiantes

Esta Tesis plantea la pregunta de si el uso de morteros con parafinas microencapsuladas combinado con colectores solares térmicos puede reducir el consumo de energías convencionales, en un sistema tradicional de suelo radiante. Se pretende contribuir al conocimiento acerca del efecto que produce en el edificio, el calor latente acumulado en suelos radiantes, utilizando morteros de cemento Portland con material de cambio de fase (PCM), en conjunto con la energía solar. Para cumplir con este propósito, la investigación se desarrolla considerando diversos aspectos. En primer lugar, se revisa y analiza la documentación disponible en la actualidad, de almacenamiento de energía mediante calor latente en la construcción, y en particular la aplicación de microcápsulas de PCM en morteros y suelos radiantes. También se revisa la documentación relacionada con la aplicación de la energía solar térmica y en suelo radiante. Se analiza la normativa vigente respecto al material, a los colectores solares y al suelo radiante. Se verifica que no hay normativa relacionada con mortero-PCM, debido a esto se aplica en la investigación una adaptación de la existente. La fase experimental desarrollada esta principalmente dirigida a la cuantificación, caracterización y evaluación de las propiedades físicas, mecánicas y térmicas del mortero de cemento Portland con parafinas microencapsuladas. Los resultados obtenidos y su análisis, permiten conocer el comportamiento de este tipo de morteros, con las diferentes variables aplicadas en la investigación. Además, permite disponer de la información necesaria, para crear una metodología para el diseño de morteros con parafina microencapsulada, tanto del punto de vista de su resistencia a la compresión y contenido de PCM, como de su comportamiento térmico como acumulador de calor. Esto se logra procesando la información obtenida y generando modelos matemáticos, para dosificar mezclas, y predecir la acumulación de calor en función de su composición. Se determinan los tipos y cantidades de PCM, y el cemento más adecuado. Se obtienen importantes conclusiones respecto a los aspectos constructivos a considerar en la aplicación de morteros con PCM, en suelo radiante. Se analiza y evalúa la demanda térmica que se puede cubrir con el suelo radiante, utilizando morteros con parafina microencapsulada, a través de la acumulación de energía solar producida por colectores solares, para condiciones climáticas, técnicas y tipologías constructivas específicas. Se determina que cuando los paneles cubren más de 60 % de la demanda por calefacción, se puede almacenar en los morteros con PCM, el excedente generado durante el día. Se puede cubrir la demanda de acumulación de energía con los morteros con PCM, en la mayoría de los casos analizados. Con esto, se determina que el uso de morteros con PCM, aporta a la eficiencia energética de los edificios, disminuyendo el consumo de energías convencionales, reemplazándola por energía solar térmica. En esta investigación, el énfasis está en las propiedades del material mortero de cemento-PCM y en poder generar metodologías que faciliten su uso. Se aborda el uso de la energía solar, para verificar que es posible su acumulación en morteros con PCM aplicados en suelo radiante, posibilitando el reemplazo de energías convencionales. Quedan algunos aspectos de la aplicación de energía solar a suelo radiante con morteros con PCM, que no han sido tratados con la profundidad que requieren, y que resultan interesantes de evaluar en este tipo de aplicaciones constructivas, como entre otros, los relacionados con la cuantificación de los ahorros de energía en las diferentes estaciones del año, de la estabilización de temperaturas internas, su análisis de costo y la optimización de este tipo de sistemas para utilización en verano, los que dan pie para otras Tesis o proyectos de investigación. ABSTRACT This Thesis proposes the question of whether the use of mortars with microencapsulated paraffin combined with solar thermal collectors can reduce conventional energy consumption in a traditional heating floor system. It aims to contribute to knowledge about the effect that it has on the building, the latent heat accumulated in heating floor, using Portland cement mortars with phase change material (PCM), in conjunction with solar energy. To fulfill this purpose, the research develops it considering various aspects. First, it reviews and analyzes the documentation available today, about energy storage by latent heat in the building, and in particular the application of PCM microcapsules in mortars and heating floors. It also reviews the documentation related to the application of solar thermal energy and heating floor. Additionally, it analyzes the current regulations regarding to material, solar collectors and heating floors. It verifies that there aren’t regulations related to PCM mortar, due to this, it applies an adaptation in the investigation. The experimental phase is aimed to the quantification, mainly, characterization and evaluation of physical, mechanical and thermal properties of Portland cement mortar with microencapsulated paraffin. The results and analysis, which allow us to know the behavior of this type of mortars with different variables applied in research. It also allows having the information necessary to create a methodology for designing mortars with microencapsulated paraffin, both from the standpoint of its resistance to compression and PCM content, and its thermal performance as a heat accumulator. This accomplishes by processing the information obtained, and generating mathematical models for dosing mixtures, and predicting heat accumulation depending on their composition. The research determines the kinds and amounts of PCM, and the most suitable cement. Relevant conclusions obtain it regarding constructive aspects to consider in the implementation of PCM mortars in heating floor. Also, it analyzes and evaluates the thermal demand that it can be covered in heating floor using microencapsulated paraffin mortars, through the accumulation of solar energy produced by solar collectors to weather conditions, technical and specific building typologies. It determines that if the panels cover more than 60% of the demand for heating, the surplus generated during the day can be stored in PCM mortars. It meets the demand of energy storage with PCM mortars, in most of the cases analyzed. With this, it determines that the use of PCM mortars contributes to building energy efficiency, reducing consumption of conventional energy, replacing it with solar thermal energy. In this research approaches the use of solar energy to determine that it’s possible to verify its accumulation in PCM mortars applied in heating floor, enabling the replacement of conventional energy. The emphasis is on material properties of PCM mortar and, in order to generate methodologies to facilitate their use. There are some aspects of solar energy application in PCM mortars in heating floor, which have not been discussed with the depth required, and that they are relevant to evaluate in this kind of construction applications, including among others: the applications related to the energy savings quantification in different seasons of the year, the stabilizing internal temperatures, its cost analysis and optimization of these systems for use in summer, which can give ideas for other thesis or research projects.

The orbital-motion-limited regime of cylindrical Langmuir probes

An asymptotic analysis of electron collection at high bias Fp serves to determine the domain of validity of the orbital-motion-limited regime of cylindrical Langmuir probes, which is basic for the workings of conductive bare tethers. The radius of a wire collecting OML current in an unmagnetized plasma at rest cannot exceed a value, Rmax , which is found to exhibit a minimum as a function of Fp ; atFp values of interest, Rmax is already increasing and is larger than the electron Debye length lDe . The breakdown of the regime relates to conditions far fromthe probe, at electron energies comparable to the ion thermal energy, kTi ; Rmax is found to increase with Ti . It is also found that ~1! the maximumwidth of a thin tape, if used instead of a wire, is 4Rmax ; ~2! the electron thermal gyroradius must be larger than both R and lDe for magnetic effects to be negligible; and ~3! conditions applying to the tether case are such that trapped-orbit effects are negligible.

Review of the C-nat(n,gamma) cross section and criticality calculations of the graphite moderated reactor BR1

A review of the experimental data for natC(n,c) and 12C(n,c) was made to identify the origin of the natC capture cross sections included in evaluated data libraries and to clarify differences observed in neutronic calculations for graphite moderated reactors using different libraries. The performance of the JEFF-3.1.2 and ENDF/B-VII.1 libraries was verified by comparing results of criticality calculations with experimental results obtained for the BR1 reactor. This reactor is an air-cooled reactor with graphite as moderator and is located at the Belgian Nuclear Research Centre SCK-CEN in Mol (Belgium). The results of this study confirm conclusions drawn from neutronic calculations of the High Temperature Engineering Test Reactor (HTTR) in Japan. Furthermore, both BR1 and HTTR calculations support the capture cross section of 12C at thermal energy which is recommended by Firestone and Révay. Additional criticality calculations were carried out in order to illustrate that the natC thermal capture cross section is important for systems with a large amount of graphite. The present study shows that only the evaluation carried out for JENDL-4.0 reflects the current status of the experimental data.

Pre-diseño de una instalación mixta fotovoltaica-térmica para una vivienda

El objetivo del presente proyecto es realizar el pre-diseño de una instalación solar mixta fotovoltaica-térmica para satisfacer la demanda eléctrica para iluminación y para parte de las necesidades de energía térmica para agua caliente de una vivienda. El proyecto define las condiciones técnicas de la instalación a partir de la radiación solar registrada en la localización elegida. Además de incluir el estudio económico y los planos correspondientes que indican la viabilidad del mismo. Como puntos a destacar en el proyecto, se puede tomar los datos obtenidos de generación eléctrica y térmica, la viabilidad técnica y económica y el análisis de la incipiente tecnología de paneles híbridos fotovoltaicos-térmicos. La incorporación de las energías renovables es ya una realidad para las viviendas de nueva construcción, en cambio son pocas las nuevas instalaciones en edificios o viviendas ya construidas. Es importante promover este tipo de tecnologías con objetivo de reducir la dependencia actual de los combustibles fósiles y evitar así sus efectos nocivos al medio ambiente. ABSTRACT The purpose of this project is to carry out the draft design of a solar mixed photovoltaic-thermal installation to satisfy the electrical and thermal demand in a building, for lighting as well as for some of the energy required for water heating. The project defines the technical conditions of the system, given the solar radiation registered in the chosen location. It also includes the economic analysis and the respective plans that indicates the viability of the project. The highlights of the project are the following: electricity and thermal energy generation data, the technical and financial viability and the analysis of the new technology of the Photovoltaic-Thermal hybrid solar collectors. The inclusion of renewable energies is already a living reality for newly constructed buildings. By contrast, they are rarely implemented in old buildings. In order to be able to reduce the fossil fuels dependency, and in doing so, avoid its damaging effects on the environment, it is very important to promote the use of these cleaner technologies.

Arquitectura antidesertización. Fluidez, biodiversidad, hidrofilia y transpirabilidad

La escasez de recursos, la desertización creciente y el previsible calentamiento global forman un escenario físico sin precedentes que urge la revisión de las relaciones entre arquitectura y agua en la urbanización de los paisajes secos, donde la aridez es el factor limitante principal. Cuestionar la idea de escasez, la de residuo o la de confort es el punto de partida para analizar la hidrología urbana. La condición ubicua y dinámica del agua, sus continuos cambios de estado y las implicaciones energéticas y ambientales involucradas argumentan a favor de un entendimiento integral, holístico, que aborda el diseño en relación a lo paisajístico, lo infraestructural y lo ambiental como un único ámbito de investigación, planteado en términos no solo de materia o de escasez, sino de energía. Este trabajo se interesa por el rol de la arquitectura en este proyecto conjunto, integral, del espacio físico con el ciclo hidrológico donde lo orgánico, lo geológico y lo atmosférico están ligados, y donde las categorías de lo hidrológico y lo hidráulico se confunden. Las profundas implicaciones culturales en la construcción de la naturaleza urbana y en la relación con el cuerpo humano adquieren especial notoriedad en los modelos de paisaje y de espacio público adoptados, importados desde las geografías húmedas, y en la estigmatización del agua desde los presupuestos del higienismo decimonónico, que conduce al hidrofugado general de una ciudad aséptica y estéril, que se extiende hasta las envolventes de fachadas estancas y los interiores blancos y satinados. La búsqueda de referentes salta la modernidad hacia contextos de baja energía como el oasis tradicional de las tierras áridas, que concilia la formación de un ecosistema productivo con la climatización de un espacio público exterior, o los ambientes aislados de la investigación aeroespacial, con ciclos cerrados de materia. Las condiciones del ciclo del agua, como la vinculación con el suelo y el territorio, la capacidad de disolver, de mezclarse y de lavar, su volumen variable y su papel como termorregulador señalan el interés que características físicas como la fluidez, la biodiversidad, la hidrofilia y la transpirabilidad tienen para una arquitectura con competencias hidráulicas y un espacio urbano transparente a los procesos del agua. La morfología y localización, la elección de escalas, jerarquías y relaciones entre espacios y la reformulación de los sistemas constructivos aparecen como herramientas y categorías propias desde las que proponer mejores respuestas a problemas como la deshidratación, la erosión y la contaminación. Una urbanización permeable e hidrófila que absorba el agua como un recurso valioso, nuevos ensamblajes para la bioquímica urbana (que introduzcan una idea de limpieza más próxima a fertilidad que a la desinfección), y el diseño de las condiciones atmosféricas a través de una arquitectura transpirable, que se empapa y rezuma frescor, son las claves de este nuevo proyecto. La ciudad se piensa como una síntesis multiescalar de espacios hidráulicos que aporta mayor resiliencia frente a la desertificación y las condiciones climáticas extremas, y mayor visibilidad en la escena pública al agua y a las inevitables conexiones entre ecología y economía. Pero también es una oportunidad para revisar las categorías disciplinares, para renovar las consistencias materiales, las calidades ambientales y las relaciones entre el cuerpo y el espacio. ABSTRACT The shortage of resources, foreseeable global warming and increasing desertification create an unprecedented prospect that question the existing relationships between water and architecture, in the urbanization of the arid lands. The awareness of the huge volumes of water that pierce unnoticed through urban space, their impact on the landscape as well as on environmental qualities, promote a design field where cultural, social and political considerations intersect, related to the body and the physical experience of space within the built environment. Fluidity and ubiquity, solution ability, variability and cyclical processes are characteristic of water as material, directly related with the fields of potential, chemical and thermal energy and the reality of its mass, as it occupies a changing volume in space. These are also the imposing cross sections that water introduces into the project, that argue in favor of a comprehensive and holistic understanding, of addressing design in relationship to landscape, infrastructure and environmental issues as a one single area of research. This work attempts to investigate how architecture, with its specific tools, can partake in the design of water cycle in the space, linking the organic, geological, and atmospheric, blurring the lines between hydrology and hydraulic. It aims to identify issues, within the continuous query associated with water, that deal with the architectural project and may have here better results. The deep cultural implications in the construction of urban nature and the relationship with the body, acquire special notoriety in the models of landscape and public space adopted, imported from humid geographies. Also in the stigmatization of water from the premises of nineteenth- century hygienics, which lead to the entire waterproofing of an aseptic and sterile city, to the sealed facades and white and polished interiors. The search for alternative references goes beyond modernity towards a mindset of low energy, as the traditional oasis of arid lands, which aims to reconcile the formation of a productive ecosystem with the conditioning of an outdoor public space, or the controlled environments of aerospace research, with closed cycles of matter. Fluidity, biodiversity, hydrophilicity and breathability are characteristic of an architecture with hydraulic competences. The distributing phenomenon of water, its necessary connectivity to the ground and to small cycles in the ecosystems, shows strong affinities with an infrastructural architecture, as an alternative to large-scale centralized networks. Its volume has approximated to the dimensions of the built space, promoting a new found condition of coexistence. A permeable and hydrophilic urbanization absorbs water as a valuable resource; new assemblies for urban biochemistry introduce an idea of sanitation closer to fertility than to disinfection; a breathable architecture that soaks and exudes freshness design the atmospheric conditions: these are the essential components of this new project. The city is understood as a synthesis of multi-scale hydraulic spaces that provides greater resilience against desertification and increases the visibility of water and the linkages between ecology and economy in the public scene. It is also an opportunity to review the disciplinary categories of architecture, the material consistencies, the environmental qualities and the relationship between body and space.