CFD simulations of flow and heat transfer through the porous interface of a metal foam heat exchanger

This paper offers numerical modelling of a waste heat recovery system. A thin layer of metal foam is attached to a cold plate to absorb heat from hot gases leaving the system. The heat transferred from the exhaust gas is then transferred to a cold liquid flowing in a secondary loop. Two different foam PPI (Pores Per Inch) values are examined over a range of fluid velocities. Numerical results are then compared to both experimental data and theoretical results available in the literature. Challenges in getting the simulation results to match those of the experiments are addressed and discussed in detail. In particular, interface boundary conditions specified between a porous layer and a fluid layer are investigated. While physically one expects much lower fluid velocity in the pores compared to that of free flow, capturing this sharp gradient at the interface can add to the difficulties of numerical simulation. The existing models in the literature are modified by considering the pressure gradient inside and outside the foam. Comparisons against the numerical modelling are presented. Finally, based on experimentally-validated numerical results, thermo-hydraulic performance of foam heat exchangers as waste heat recovery units is discussed with the main goal of reducing the excess pressure drop and maximising the amount of heat that can be recovered from the hot gas stream.

A matrix converter based Inductive Power Transfer system

Typical Inductive Power Transfer (IPT) systems employ two power conversion stages to generate a high frequency current from low frequency utility supply. This paper proposes a matrix converter based IPT system that facilitates the generation of high frequency current through a single power conversion stage. The proposed matrix converter topology transforms a 3-phase low frequency voltage system to a high frequency single phase voltage which in turn powers a series compensated IPT system. A comprehensive mathematical model is developed to investigate the behavior of the proposed IPT topology. Theoretical results are presented in comparison to simulations, which are performed in Matlab/ Simulink, to demonstrate the applicability of the proposed concept and the validity of the developed model.

Contrast transfer function correction applied to cryo-electron tomography and sub-tomogram averaging

Cryo-electron tomography together with averaging of sub-tomograms containing identical particles can reveal the structure of proteins or protein complexes in their native environment. The resolution of this technique is limited by the contrast transfer function (CTF) of the microscope. The CTF is not routinely corrected in cryo-electron tomography because of difficulties including CTF detection, due to the low signal to noise ratio, and CTF correction, since images are characterised by a spatially variant CTF. Here we simulate the effects of the CTF on the resolution of the final reconstruction, before and after CTF correction, and consider the effect of errors and approximations in defocus determination. We show that errors in defocus determination are well tolerated when correcting a series of tomograms collected at a range of defocus values. We apply methods for determining the CTF parameters in low signal to noise images of tilted specimens, for monitoring defocus changes using observed magnification changes, and for correcting the CTF prior to reconstruction. Using bacteriophage PRDI as a test sample, we demonstrate that this approach gives an improvement in the structure obtained by sub-tomogram averaging from cryo-electron tomograms.

Blood transfer devices for malaria rapid diagnostic tests : evaluation of accuracy, safety and ease of use

Background: Malaria rapid diagnostic tests (RDTs) are increasingly used by remote health personnel with minimal training in laboratory techniques. RDTs must, therefore, be as simple, safe and reliable as possible. Transfer of blood from the patient to the RDT is critical to safety and accuracy, and poses a significant challenge to many users. Blood transfer devices were evaluated for accuracy and precision of volume transferred, safety and ease of use, to identify the most appropriate devices for use with RDTs in routine clinical care. Methods: Five devices, a loop, straw-pipette, calibrated pipette, glass capillary tube, and a new inverted cup device, were evaluated in Nigeria, the Philippines and Uganda. The 227 participating health workers used each device to transfer blood from a simulated finger-prick site to filter paper. For each transfer, the number of attempts required to collect and deposit blood and any spilling of blood during transfer were recorded. Perceptions of ease of use and safety of each device were recorded for each participant. Blood volume transferred was calculated from the area of blood spots deposited on filter paper. Results: The overall mean volumes transferred by devices differed significantly from the target volume of 5 microliters (p < 0.001). The inverted cup (4.6 microliters) most closely approximated the target volume. The glass capillary was excluded from volume analysis as the estimation method used is not compatible with this device. The calibrated pipette accounted for the largest proportion of blood exposures (23/225, 10%); exposures ranged from 2% to 6% for the other four devices. The inverted cup was considered easiest to use in blood collection (206/ 226, 91%); the straw-pipette and calibrated pipette were rated lowest (143/225 [64%] and 135/225 [60%] respectively). Overall, the inverted cup was the most preferred device (72%, 163/227), followed by the loop (61%, 138/227). Conclusions: The performance of blood transfer devices varied in this evaluation of accuracy, blood safety, ease of use, and user preference. The inverted cup design achieved the highest overall performance, while the loop also performed well. These findings have relevance for any point-of-care diagnostics that require blood sampling.

Cascaded multilevel converter based bidirectional inductive power transfer (BIPT) system

A typical low power IPT system employs an H-Bridge converter with a simple control strategy to generate a high frequency current from DC power supply. This paper proposes a cascaded multilevel converter for bidirectional IPT (BIPT) systems, which is suitable for low to medium power applications as well as for situations such as PV cells where several individual DC sources are to be utilized. A novel modulation strategy is proposed for the multilevel converter with the aim of minimizing switching losses. Series - Series (SS) compensation circuit is adopted for the IPT system and a mathematical model is presented to minimize the coil losses of the system under varying output power. Theoretical results presented in comparison to the simulations to demonstrate the applicability of the proposed concept and the validity of the developed model. The experimental results show the feasibility of the proposed phase shift modulation.

The pollution release and transfer register system in the U.S. and Japan : an analysis of productivity

This study analyzes Total Factor Productivity (TFP), which includes all categories of productivity. Our measure investigates productivity in the context of the provision and dissemination of environmental information policies. We investigated data on the emission of toxic chemical substances for the U.S. and Japanese manufacturing firms, including 386 firms for the period 1999-2007 and 466 firms for the period 2001-2008. The results show that productivity improved in all nine industrial sectors and that pollution levels were high in the U.S. and Japan from 2001 to 2007. In particular, the electronics industry improved rapidly after 2002 in both countries, which may be attributed to the enforcement of RoHS and the REACH directive in Europe. As a result of these stringent policies on toxic chemical emissions, the U.S. and Japanese firms, many of which export to the European market, have strong incentives to reduce their toxic chemical emissions.

Knowledge Transfer in Transnational Programmes : Opportunities and Challenges for the Pacific Region

The globalised world: The current higher education community The last decade has seen rapid changes in the landscape of higher education (HE) throughout the world, largely as a product of globalisation. A major effect has been to propel the interconnectedness between nations and people across the globe (Scholte, 2005). The use of information and communication technology (ICT) has diminished the distance between countries. The world’s economies are becoming more integrated and interrelated through neoliberal economic policies, free trade agreements and open access of goods and services beyond national borders, policies promulgated by organisations such as the World Trade Organization and The World Bank (Marginson & Ordorika, 2011; Mok, 2011). As a consequence, universities are operating at global, national and local levels simultaneously. In the Pacific region, new universities are emerging. For example, Fiji now has one regional and two national universities; Samoa has a national university and Solomon Islands has an institute of higher education. These new players add to regional competition as they open opportunities for global partnerships and transnational programmes. Thus, participating at these multiple levels is inevitable, and no university is immune to these changes (Marginson, Kaur & Sawir, 2011a). Universities are now part of the global HE community that cannot be confined within a nation’s borders. Transitional HE programmes are perhaps one of the most evident demonstrations of the interconnectedness of universities across countries in this global era.

Prevalence of asymptomatic malaria and bed net ownership and use in Bhutan, 2013 : a country earmarked for malaria elimination

Background With dwindling malaria cases in Bhutan in recent years, the government of Bhutan has made plans for malaria elimination by 2016. This study aimed to determine coverage, use and ownership of LLINs, as well as the prevalence of asymptomatic malaria at a single time-point, in four sub-districts of Bhutan. Methods A cross-sectional study was carried out in August 2013. Structured questionnaires were administered to a single respondent in each household (HH) in four sub-districts. Four members from 25 HH, randomly selected from each sub-district, were tested using rapid diagnostic tests (RDT) for asymptomatic Plasmodium falciparum and Plasmodium vivax infection. Multivariable logistic regression models were used to identify factors associated with LLIN use and maintenance. Results All blood samples from 380 participants tested negative for Plasmodium infections. A total of 1,223 HH (92.5% of total HH) were surveyed for LLIN coverage and use. Coverage of LLINs was 99.0% (1,203/1,223 HH). Factors associated with decreased odds of sleeping under a LLIN included: washing LLINs nine months compared to washing LLINs every six months; HH in the least poor compared to the most poor socio-economic quintile; a HH income of Nu 5,001-10,000 (US$1 = Nu 59.55), and Nu >10,000, compared to HH with income of

Electronic conveyancing in Australia : is anyone concerned about security?

We have previously suggested that three proof requirements are essential for a sustainable land registration system. These were proof of identity, proof of ownership and authority to deal. Our attention in this article is drawn to the security framework that surrounds these requirements. We will ask whether the introduction of the Property Exchange of Australia (PEXA), and its underpinning regulatory regime will meet the concerns that we have in relation to them. In drawing out some problems with PEXA, we then offer an innovative idea, sourced from the transfer of equities that could serve to generate discussion on how we can ensure the Torrens system of land registration is sustainable for another 160 years. We also canvass some more incremental suggestions that evolve out of what we currently do, as well as outlining some comparative externally sourced ideas as to how the transfer and ownership of land can be made safer for all citizens. Such a goal is imperative when land transfer and secure property ownership is a critical component of the economic infrastructure of a modern society.

Cyclododecane as support material for clean and facile transfer of large-area few-layer graphene

The transfer of chemical vapor deposited graphene is a crucial process, which can affect the quality of the transferred films and compromise their application in devices. Finding a robust and intrinsically clean material capable of easing the transfer of graphene without interfering with its properties remains a challenge. We here propose the use of an organic compound, cyclododecane, as a transfer material. This material can be easily spin coated on graphene and assist the transfer, leaving no residues and requiring no further removal processes. The effectiveness of this transfer method for few-layer graphene on a large area was evaluated and confirmed by microscopy, Raman spectroscopy, x-ray photoemission spectroscopy, and four-point probe measurements. Schottky-barrier solar cells with few-layer graphene were fabricated on silicon wafers by using the cyclododecane transfer method and outperformed reference cells made by standard methods.

Convergence in the ownership and governance of East Asian firms

In the past decade, policymakers in over 70 markets have introduced corporate governance codes or best practice guidelines. In East Asia, they have been introduced in Hong Kong in 1999 and 2006, Indonesia in 2000 and 2007, Malaysia in 2000 and 2007, the Philippines in 2002, Singapore iu 2001 and 2005, South Korea in 2003, Taiwan iu 2002 and Thailand iu 2006. The common focus of these codes is to encourage but not force companies to improve their corporate governance practices to a specified target level, e.g., board independence of 30%. Another commonality is that the guidelines apply to all listed companies regardless of their ownership structure or other characteristics.

The ethics, aesthetics and practical politics of ownership in co-creative media

What is ‘best practice’ when it comes to managing intellectual property rights in participatory media content? As commercial media and entertainment business models have increasingly come to rely upon the networked productivity of end-users (Banks and Humphreys 2008) this question has been framed as a problem of creative labour made all the more precarious by changing employment patterns and work cultures of knowledge-intensive societies and globalising economies (Banks, Gill and Taylor 2014). This paper considers how the problems of ownership are addressed in non-commercial, community-based arts and media contexts. Problems of labour are also manifest in these contexts (for example, reliance on volunteer labour and uncertain economic reward for creative excellence). Nonetheless, managing intellectual property rights in collaborative creative works that are created in community media and arts contexts is no less challenging or complex than in commercial contexts. This paper takes as its focus a particular participatory media practice known as ‘digital storytelling’. The digital storytelling method, formalised by the Centre for Digital Storytelling (CDS) from the mid-1990s, has been internationally adopted and adapted for use in an open-ended variety of community arts, education, health and allied services settings (Hartley and McWilliam 2009; Lambert 2013; Lundby 2008; Thumin 2012). It provides a useful point of departure for thinking about a range of collaborative media production practices that seek to address participation ‘gaps’ (Jenkins 2006). However the outputs of these activities, including digital stories, cannot be fully understood or accurately described as user-generated content. For this reason, digital storytelling is taken here to belong to a category of participatory media activity that has been described as ‘co-creative’ media (Spurgeon 2013) in order to improve understanding of the conditions of mediated and mediatized participation (Couldry 2008). This paper reports on a survey of the actual copyrighting practices of cultural institutions and community-based media arts practitioners that work with digital storytelling and similar participatory content creation methods. This survey finds that although there is a preference for Creative Commons licensing a great variety of approaches are taken to managing intellectual property rights in co-creative media. These range from the use of Creative Commons licences (for example, Lambert 2013, p.193) to retention of full copyrights by storytellers, to retention of certain rights by facilitating organisations (for example, broadcast rights by community radio stations and public service broadcasters), and a range of other shared rights arrangements between professional creative practitioners, the individual storytellers and communities with which they collaborate, media outlets, exhibitors and funders. This paper also considers how aesthetic and ethical considerations shape responses to questions of intellectual property rights in community media arts contexts. For example, embedded in the CDS digital storytelling method is ‘a critique of power and the numerous ways that rank is unconsciously expressed in engagements between classes, races and gender’ (Lambert 117). The CDS method privileges the interests of the storyteller and, through a transformative workshop process, aims to generate original individual stories that, in turn, reflect self-awareness of ‘how much the way we live is scripted by history, by social and cultural norms, by our own unique journey through a contradictory, and at times hostile, world’ (Lambert 118). Such a critical approach is characteristic of co-creative media practices. It extends to a heightened awareness of the risks of ‘story theft’ and the challenges of ownership and informs ideas of ‘best practice’ amongst creative practitioners, teaching artists and community media producers, along with commitments to achieving equitable solutions for all participants in co-creative media practice (for example, Lyons-Reid and Kuddell nd.). Yet, there is surprisingly little written about the challenges of managing intellectual property produced in co-creative media activities. A dialogic sense of ownership in stories has been identified as an indicator of successful digital storytelling practice (Hayes and Matusov 2005) and is helpful to grounding the more abstract claims of empowerment for social participation that are associated with co-creative methods. Contrary to the ‘change from below’ philosophy that underpins much thinking about co-creative media, however, discussions of intellectual property usually focus on how methods such as digital storytelling contribute to the formation of copyright law-compliant subjects, particularly when used in educational settings (for example, Ohler nd.). This also exposes the reliance of co-creative methods on the creative assets storytellers (rather than on the copyrighted materials of the media cultures of storytellers) as a pragmatic response to the constraints that intellectual property right laws impose on the entire category of participatory media. At the level of practical politics, it also becomes apparent that co-creative media practitioners and storytellers located in copyright jurisdictions governed by ‘fair use’ principles have much greater creative flexibility than those located in jurisdictions governed by ‘fair dealing’ principles.

A tag-based personalized item recommendation system using tensor modeling and topic model approaches

This research falls in the area of enhancing the quality of tag-based item recommendation systems. It aims to achieve this by employing a multi-dimensional user profile approach and by analyzing the semantic aspects of tags. Tag-based recommender systems have two characteristics that need to be carefully studied in order to build a reliable system. Firstly, the multi-dimensional correlation, called as tag assignment tag>, should be appropriately modelled in order to create the user profiles [1]. Secondly, the semantics behind the tags should be considered properly as the flexibility with their design can cause semantic problems such as synonymy and polysemy [2]. This research proposes to address these two challenges for building a tag-based item recommendation system by employing tensor modeling as the multi-dimensional user profile approach, and the topic model as the semantic analysis approach. The first objective is to optimize the tensor model reconstruction and to improve the model performance in generating quality rec-ommendation. A novel Tensor-based Recommendation using Probabilistic Ranking (TRPR) method [3] has been developed. Results show this method to be scalable for large datasets and outperforming the benchmarking methods in terms of accuracy. The memory efficient loop implements the n-mode block-striped (matrix) product for tensor reconstruction as an approximation of the initial tensor. The probabilistic ranking calculates the probabil-ity of users to select candidate items using their tag preference list based on the entries generated from the reconstructed tensor. The second objective is to analyse the tag semantics and utilize the outcome in building the tensor model. This research proposes to investigate the problem using topic model approach to keep the tags nature as the “social vocabulary” [4]. For the tag assignment data, topics can be generated from the occurrences of tags given for an item. However there is only limited amount of tags availa-ble to represent items as collection of topics, since an item might have only been tagged by using several tags. Consequently, the generated topics might not able to represent the items appropriately. Furthermore, given that each tag can belong to any topics with various probability scores, the occurrence of tags cannot simply be mapped by the topics to build the tensor model. A standard weighting technique will not appropriately calculate the value of tagging activity since it will define the context of an item using a tag instead of a topic.