Gas-metal reactions and porosity in the inert gas arc welding of copper

A study has been made of the effects of welding and material variables on the occurrence of porosity in tungsten inert gas arc welding of copper. The experiments were based on a statistical design and variables included, welding current, welding speed, arc atmosphere composition, inert gas flow rate, weld preparation, and base material. The extent of weld metal porosity was assessed by density measurement and its morphology by X-ray radiography and metallography. In conjunction with this the copper-steam reaction has been investigated under conditions of controlled atmosphere arc melting. The welding experiments have shown that the extent of steam porosity is increased by increased water vapour content of the arc atmosphere, increased oxygen content of the base material and decreased welding speed. The arc melting experiments have shown that the steam reaction occurs in the body of the weld pool and proceeds to an apparent equi1ibrium state appropriate to to its temperature, the hydrogen and oxygen being supplied by the dissociation of water vapour in the arc atmosphere. It has been shown conclusively that nitrogen porosity can occur in the tungsten inert gas arc welding of copper and that this porosity can be eliminated by using filler wires containing small amounts of aluminum and titanium. Since it has been shown to be much more difficult to produce sound butt welds than melt runs it has been concluded that the porosity associated with joint fit up is due to nitrogen entrained into tho arc atmosphere. Clearly atmospheric entrainment would also, to a much lesser extent, involve water vapour. From a practical welding point of view it has thus been postulated that use of a filler wire containing small amounts of aluminum and/or titanium would eliminate both forms of porosity since these elements are both strongJy deoxidising and denitriding.

Resistance welding of coated steels

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Prediction of welding distortion in butt joint of thin plates

This paper investigates distortions and residual stresses induced in butt joint of thin plates using Metal Inert Gas welding. A moving distributed heat source model based on Goldak's double-ellipsoid heat flux distribution is implemented in Finite Element (FE) simulation of the welding process. Thermo-elastic-plastic FE methods are applied to modelling thermal and mechanical behaviour of the welded plate during the welding process. Prediction of temperature variations, fusion zone and heat affected zone as well as longitudinal and transverse shrinkage, angular distortion, and residual stress is obtained. FE analysis results of welding distortions are compared with existing experimental and empirical predictions. The welding speed and plate thickness are shown to have considerable effects on welding distortions and residual stresses. © 2009 Elsevier Ltd. All rights reserved.

The application of laser welding on Left Ventricular Assist Device (LVAD)

A successful and useful treatment for end-stage heart failure is Left ventricular assist device (LVAD). An important part - a hydrodynamically suspended impeller exposed to corrosive conditions, required to sealed hermetically into micro packages. Laser beam welded (LBW) Ti6Al4V alloy has been adopted in anti-corrosion micro packages for the impeller of a (LVAD). Thin and narrow welds were required for such medical equipment. Pulsed Nd:YAG welding was successfully adopted as sealing method for the impeller. ©2011 IEEE.

A Nádor utcától a Budaörsi útig: A fél évszázados Közgazdaságtudományi Intézet

Manapság, amikor a legfontosabb történések a Föld virtuális idegrendszerét jelentő számítógép-hálózatokon, azaz sehol és mindenhol zajlanak, mond-e valamit a címben jelzett két, nagyon is megfogható hely: az elegáns palota a Belváros szívében és az óriásreklámmal éktelenkedő betonszörny a balatoni autópálya torkolatában? A közgazdászok számára (kiváltképpen, ha idősebbek, mint a jubileumát ünneplő Közgazdaságtudományi Intézet) mindenképpen. Az INTÉZET – így csupa nagybetűvel – megalakulásától kezdve fogalom volt, a falai között zajló vitáknak hírértéket tulajdonítottak a szakmában. Néhány évtizede még a viccek is úgy kezdődtek, két közgazdász sétál a Nádor (akkor még Münnich Ferenc) utcában …

Avaliação do comportamento meckntco de soldas TIG em tubos AISI 316 para varetas combustíveis

O comportamento mecânico sob tração e fluência e o efeito da temperatura de serviço, foram averiguados na selarem de um material proposto para vareta combustível de reatores nucleares. Os testes foram realizados em tubos sem costura de aço AISI 3x6, 20% deformado a frio, soldados pelo processo TIG autógeno, auto matizado.

Possibilities of advanced MAG-welding processes in shipbuilding

In shipbuilding industry welding of primer coated and tack welded steel products cause different issues. Primer coated steel products are commonly used at shipyards to ensure corrosion free storage of products in outdoor conditions. However usage of primer can cause imperfections to welds. To prevent porosity primed steel products are usually welded with tubular welding wires. Tack welds cause commonly interferences in mechanized welding when over welded, which increases costs related to welding due to increased need of preparing and repairing. The aim of this study is to research possibilities of advanced solid wire MAG-welding processes to deal with these two previously mentioned problems. This study concentrates to examine possibilities of MAG-welding, pulse MAG-welding, double pulse MAG-welding, RapidArc and ForceArc processes. Large amount of experiments were made to find out the produced porosity and the ability to over weld tack welds with each process in different circumstances. In welding of primed steel products porosity is caused mainly by hydrogen, CO, CO2, nitrous gases and zinc fumes. It was found in experiments that porosity of MAG-welding can be greatly decreased by using pulse MAG-welding instead. Also reduction of welding speed, usage of air gap and usage of solid wire product with higher amount of alloying elements reduces porosity. Researched advanced MAG-welding processes did not have an improvement into over welding of tack welds. With studied throat thicknesses and welding positions conventional MAG-welding managed better over welding of tack welds than the four studied advanced MAG-welding processes. Studied solid wire MAG-welding processes would be best suited at shipyard for mechanized welding in welding position PB. In welding positions PD and PG tubular welding wires are clearly more productive.

Comparison of EN & ASME welding and its allied processes standards

This thesis is made in cooperation with Wärtsilä and Sandvik. The main purpose of the thesis is to clarify the best suitable American standards for European standards used in Wärtsilä’s investigation checklist and to make wide and easily readable tables for Wärtsilä and their subcontractors. One of the most important issues is to make clear if the compared American standards are demanding enough for Wärtsilä’s needs. The research is done by comparing EN standards mentioned in Wärtsilä’s investigation checklist to corresponding ASME, AWS, ASNT and ASTM standards. The research shows that there is visible lack of requirements in American standards compared to European ones. Some areas of American standards are more demanding than European standards but in larger scale EN standards are much wider and more demanding than American standards. Because of these reasons, usage of European standards should be recommended for Wärtsilä’s subcontractors to ensure the quality and reliability of production.

Hitsauksen reaaliaikaisen NDT-tarkastuksen nykytilanne

Tämän kandidaatintyön tarkoituksena on selvittää hitsien tarkastukseen käytettyjen NDT-menetelmien nykytilannetta. Työssä kerrotaan mitä reaaliaikainen NDT-tarkastus on ja mitä menetelmiä siihen voidaan käyttää. Työn tarkoituksena on antaa lukijalle kokonaiskuva NDT-tarkastuksen nykytilasta ja siinä käytettävistä menetelmistä. Tutkimus suoritettiin kirjallisuuskatsauksena. Kirjallisuuskatsaus on luonteeltaan toteava. Lähteiden etsintä suoritettiin suurimmalta osin Internet-hakuna. NDT-tarkastusmenetelmät voidaan jakaa kahteen pääkategoriaan; pinta- ja volumetrisiin menetelmiin. Kaikki tarkastusmenetelmät eivät sovellu reaaliaikaiseen tarkastukseen. Hitsien tarkastuksessa käytetyimmät reaaliaikaiset menetelmät ovat: ultraäänitarkastus, radiografinen tarkastus, optinen spektroskopia, termografia ja pyörrevirtatarkastus. Kaikilla reaaliaikaisilla menetelmillä on omat vahvuutensa ja heikkoutensa. Työssä esitetään myös CASE-esimerkkejä reaaliaikaisesta hitsien tarkastamisesta.Tärkeimpinä johtopäätöksinä voidaan nähdä se, että hitsien NDT-tarkastuksen onnistuminen on aina hyvin tapauskohtaista ja riippuu useista muuttujista. Tästä syystä tällä hetkellä NDT-tarkastusmenetelmistä ei voi valita parasta kaikkiin käyttökohteisiin sopivaa menetelmää. Monessa prosessissa NDT-tarkastustehokkuutta ei määritä mekaanisen laitteiston mittaustarkkuus, vaan tulosten analysointiin käytettyjen algoritmien tehottomuus. Tutkimuksessa esitetään myös idea hybridi-NDT-tarkastusjärjestelmästä, jolla saataisiin havaittua tehokkaasti sekä pinta-että volumetrisia virheitä.

Estudio del potencial fotovoltaico en Miraflores de la Sierra mediante TIG: análisis y publicación de resultados

El objetivo de este trabajo es ejecutar un modelo basado en herramientas SIG, LIDAR y datos de posición solar anual para el estudio del potencial fotovoltaico en el Municipio de Miraflores de la Sierra. Una vez se obtengan los resultados se realiza un análisis y una publicación de los mismos. El análisis consta de dos fases: Una primera en la que se estudian los distintos elementos resultantes por separado (Irradiación solar anual, Energía generada y Potencia instalada) y otra en la que se comparan la distribución de los resultados y las distintas tecnologías para módulos fotovoltaicos que se han estudiado. Los resultados se publican mediante una serie cartográfica de once mapas temáticos, en función de los elementos. También se crea un visor cartográfico online con parte de la información obtenida, donde se incluyen herramientas y funciones para mejorar la experiencia del usuario final del producto.

La educación geográfica empleando las TIG: una innovación necesaria

Aportación a la mesa redonda: “LA FORMACIÓN EN TIG EN LOS NUEVOS PLANES DE GRADOS Y MÁSTERES”, desarrollada en el marco del XVII Congreso Nacional de TIG.