Utilização de escória de siderurgia na cultura da goiabeira

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of reactivity rates of silicate particle-size fractions

The efficiency of sources used for soil acidity correction depends on reactivity rate (RR) and neutralization power (NP), indicated by effective calcium carbonate (ECC). Few studies establish relative efficiency of reactivity (RER) for silicate particle-size fractions, therefore, the RER applied for lime are used. This study aimed to evaluate the reactivity of silicate materials affected by particle size throughout incubation periods in comparison to lime, and to calculate the RER for silicate particle-size fractions. Six correction sources were evaluated: three slags from distinct origins, dolomitic and calcitic lime separated into four particle-size fractions (2, 0.84, 0.30 and <0.30-mm sieves), and wollastonite, as an additional treatment. The treatments were applied to three soils with different texture classes. The dose of neutralizing material (calcium and magnesium oxides) was applied at equal quantities, and the only variation was the particle-size material. After a 90-day incubation period, the RER was calculated for each particle-size fraction, as well as the RR and ECC of each source. The neutralization of soil acidity of the same particle-size fraction for different sources showed distinct solubility and a distinct reaction between silicates and lime. The RER for slag were higher than the limits established by Brazilian legislation, indicating that the method used for limes should not be used for the slags studied here.

Aplicação de corretivos de acidez do solo na implantação do sistema plantio direto

Pós-graduação em Agronomia (Agricultura) - FCA

Estudo de geopolímeros utilizando cinzas residuais do bagaço de cana-de-açúcar

Pós-graduação em Engenharia Civil - FEIS

Heavy Metals Extracted by DTPA and Organic Acids from Soil Amended with Urban or Industrial Residues

Understanding soil responses to the application of urban or industrial residues is necessary. In the current experiment, both sources of residues were applied to the soil surface of a Hapludox soil for 8 years. The four residues studied were biodigested and centrifuged sewage sludge (LB and LC, respectively), steel slag from the metallurgic industry (E), and limed mud from the pulp and cellulose industry (LCal). The residues were applied at 0, 2, 4, and 8 Mg ha(-1) four times from 2002 to 2010 when soybean was cultivated in the summer and lopsided oat and sorghum were cultivated during the winter. The contents of heavy metals were evaluated with diethylenetriaminepentaacetic acid (DTPA) and organic acids. The LB was the residue that increased the contents of soil micronutrients and heavy metals to their greatest levels, although within limits that impair the risks of environmental contamination.

Análise da viabilidade da utilização da cinza do bagaço de cana-de-açúcar como aglomerante para a produção de matrizes cimentantes

Pós-graduação em Engenharia Civil - FEIS

Fitodisponibilidade de metais utilizando ácidos orgânicos após sucessiva aplicação de resíduos no solo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Resposta da cana-de-açúcar à aplicação da escória de siderurgia como corretivo de acidez do solo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Nutrient accumulation and biomass production of alfafa after soil amendment with silicates

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise granulométrica do compósito cimentício produzido com adição de resíduos de madeira e escória

Since the early twenty-first century, the construction sector has been the second largest on the rise in the Brazilian industrial sector, with a growth of 1.4% in 2012, and is likely to remain at this level for a long time. However, unlike decades ago, the industry has been seeking in its manufacturing process, sustainable materials, encompassing in their works the concept of sustainability. Thus, the timber sector seeks to satisfy a market increasingly demanding, innovating techniques and utilization being less aggressive to the environment. The purpose of this study was to produce and evaluate the mechanical strength of the composite cement with the addition of wood residues and slag low oven. Therefore, it was made 42 specimen cement-slag-wood, carried out in two steps. Since at the first, it was varied only the slag particle size, and at the second, through the best result of the previous step, it was varied the wood particles granulometry. The mechanical performance of the composite was evaluated by the results obtained in the compression test and the physical test for determining the density of the material. In the first step of the process can be concluded that the best result was achieved with the use of slag particles retained on the 60 mesh sieve. In the second phase of the study concluded that the best results were achieved with wood particles with the large particles, i.e. particles retained on the 10 mesh sieve. Both in the first and in the second step it can be seen that there has been the influence of the particle size of the waste materials. With the obtained results, could be evaluated that the use of waste for the production of cement-slag-wood composite showed lower performance when compared to the results obtained in studies without the use of waste. However, some applications are feasible to be performed with the use of composite wood-cement-slag

Avaliação de juntas soldadas em tubos de aço carbono submetidos a altas temperatura e pressões

The welding process in industrial piping is still the most effective way to ensure the durability and quality of the wide range of industrial process, although because of the high demand for energy and quality of the produced products, the piping has been constantly tested for high pressure applications and still high temperature. The welding method analyzed is the TIG (Tungsten Inert Gas) welding or GTAW (Gas-Shielded Tungsten Arc Welding), which ones have as principal feature the utilization of a not consumable tungsten electrode in the torch extremity , in this process is necessary a protective atmosphere of inert gas. The welding TIG advantage is the obtaining of a welded seam clean and with quality for not has slag after the welding. This work has as objective show the variability in the carbon steel piping welding parameters and by the tests in four proof bodies will be shown the influence of the variation of the welding methods in a welded seam. The tests will vary since the piece to be welded preparation, till penetrating liquid tests, welding macrography, welding x-ray and traction tests. Even been a clean and with quality welding is necessary a final inspection in the seam welded looking for defects almost inevitable resulted of the welded process, the obtained results have the objective of indicate and minimize the defects to ensure quality and durability of the welded seam

Desenvolvimento de tijolos cerâmicos com escória de alto-forno

The construction industry is booming, and the federal government is heavily financially supporting public housing. This scenario is very favorable for the development of construction materials, especially low-cost construction. Thus, this study aims to develop a new class of unfired clay masonry bricks: GGBS stabilized bricks. Studies show that the ground granulated blast furnace slag, a material used as raw material in cement manufacture, can be used together with calcium oxide in soil stabilization for the manufacture of bricks. This study aims to test and identify the best parameters for the manufacture of unfired bricks, adapting its composition to the materials found in Brazil and identify the optimum curing conditions for our climate. So far preliminary studies were done to verify the technical feasibility of the material. Future studies should be done to ascertain the economic feasibility and environmental gains of such material

Resposta da soqueira da cana-de-açúcar à aplicação de nitrogênio na ausência e na presença de silício

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Disponibilidade de fósforo em solo tratado com resíduos urbanos e industriais sob sistema de plantio direto cultivado com soja

Pós-graduação em Agronomia (Agricultura) - FCA

Efeito residual do calcário e da escória de siderurgia em soqueiras da cana-de-açúcar

Pós-graduação em Agronomia (Produção Vegetal) - FCAV