Tree-ring reconstructions of winter climate and circulation indices for the southwestern United States

A key to understanding the causes for climate variability lies in understanding how atmospheric circulation influences regional climate. The goal of this research is to investigate the long-term relationships between atmospheric circulation and winter climate in the southwestern United States. Patterns of atmospheric circulation are described by circulation indices, and winter climate is defined as number of days with precipitation and mean maximum temperature for the winter wet season, November through March. Records of both circulation indices and climate variables were reconstructed with tree-ring chronologies for the period 1702-1983. The years of the highest and lowest values of circulation indices and climate variables were compared in order to investigate possible spatial and temporal relationships between extremes in circulation and climate.

Analysis of the piston ring/liner oil film development during warm-up for an SI-engine

A one-dimensional ring-pack lubrication model developed at MIT is applied to simulate the oil film behavior during the warm-up period of a Kohler spark ignition engine [1]. This is done by making assumptions for the evolution of the oil temperatures during warm-up and that the oil control ring during downstrokes is fully flooded. The ring-pack lubrication model includes features such as three different lubrication regimes, i.e. pure hydrodynamic lubrication, boundary lubrication and pure asperity contact, non-steady wetting of both inlet and outlet of the piston ring, capability to use all ring face profiles that can be approximated by piece-wise polynomials and, finally, the ability to model the rheology of multi-grade oils. Not surprisingly, the simulations show that by far the most important parameter is the temperature dependence of the oil viscosity. This dependence is subsequently examined further by choosing different oils. The baseline oil is SAE 10W30 and results are compared to those using the SAE 30 and the SAE 10W50 oils.

The development of turbine exit flow in a swan-necked inter-stage diffuser

This paper describes both the migration and dissipation of flow phenomena downstream of a transonic high-pressure turbine stage. The geometry of the HP stage exit duct considered is a swan-necked diffuser similar to those likely to be used in future engine designs. The paper contains results both from an experimental programme in a turbine test facility and from numerical predictions. Experimental data was acquired using three fast-response aerodynamic probes capable of measuring Mach number, whirl angle, pitch angle, total pressure and static pressure. The probes were used to make time-resolved area traverses at two axial locations downstream of the rotor trailing edge. A 3D time-unsteady viscous Navier-Stokes solver was used for the numerical predictions. The unsteady exit flow from a turbine stage is formed from rotordependent phenomena (such as the rotor wake, the rotor trailing edge recompression shock, the tip-leakage flow and the hub secondary flow) and vane-rotor interaction dependant phenomena. This paper describes the time-resolved behaviour and three-dimensional migration paths of both of these phenomena as they convect downstream. It is shown that the inlet flow to a downstream vane is dominated by two corotating vortices, the first caused by the rotor tip-leakage flow and the second by the rotor hub secondary flow. At the inlet plane of the downstream vane the wake is extremely weak and the radial pressure gradient is shown to have caused the majority of the high loss wake fluid to be located between the mid-height of the passage and the casing wall. The structure of the flow indicates that between a high pressure stage and a downstream vane simple two-dimensional blade row interaction does not occur. The results presented in this paper indicate that the presence of an upstream stage is likely to significantly alter the structure of the secondary flow within a downstream vane. The paper also shows that vane-rotor interaction within the upstream stage causes a 10° circumferential variation in the inlet flow angle of the 2nd stage vane.

Fibre optics monitoring of clay cuttings and embankments along London's ring motorway

Although a wide range of techniques exist for slope monitoring, the task of monitoring slopes is sometimes complicated by the extensive nature and unpredictability of slope movements. The Brillouin optical time-domain reflectometer (BOTDR) is a distributed optical fiber strain measurement technology utilising Brillouin scattering. This method measures continuous strain along a standard optical fibre over a distance up to 10 km and hence has potential to detect deformations and diagnose problems along large sections of slopes and embankments. This paper reports the demonstration of BOTDR method for monitoring surface ground movements of clay cuttings and embankments along London's ring M25 motorway. A field trial investigating varying methods of onsite fibre optic installations was conducted. The surrounding ground was artificially moved by excavating a 3 m deep trench perpendicular to the instrumented sections. Results obtained from onsite installations after slope movement demonstrate a half-pipe covered fibre optic installed on wide (200mm) Tensar ™SS20 geogrid gives the most consistent recorded strain change profile. Initial conclusions suggest this method best represents induced ground motion at the surface and hence is recommended for implementation in future sitework. Copyright ASCE 2008.

Przewalskin A: A new C-23 terpenoid with a 6/6/7 carbon ring skeleton from Salvia przewalskii maxim

Przewalskin A (1), a novel C-23 terpenoid with a 6/6/7 carbon ring skeleton, was isolated from Salvia przewalskii. Its structure was determined by comprehensive 1D NMR, 2D NMR, and MS spectroscopic analysis and subsequently confirmed by a single-crystal X

Diurnal time budget of the Black-necked Crane during the breeding season

From 26 March to 2 August 2003, both the time budget and the diurnal rhythm of behavior of breeding Black-necked Cranes (Grus nigricollis) were studied at Ruoergai Wetlands National Natural Reserve, Sichuan Province, China. The breeding season was divided

Nest site selection by Black-necked Crane Grus nigricollis in the Ruoergai Wetland, China

From 5 May 2003 to early June 2005, nest site selection of Black-necked Cranes Grits nigricollis was studied at the Ruoergai Wetland Nature Reserve (RWNR), an important breeding area for the species in China. Results showed that the crane nests only in we

Migration routes and stopover sites of Black-necked Cranes determined by satellite tracking

Because their breeding and wintering areas are in remote locations, little is known about the biology of Black-necked Cranes (Grus nigricollis), including their migratory behavior. Using satellite telemetry, we monitored the migration of Black-necked Cran

Foraging habitats and utilization distributions of Black-necked Cranes wintering at the Napahai Wetland, China

One of the most endangered populations of Black-necked Cranes (Grus nigricollis), the central population, is declining due to habitat loss and degradation, but little is known about their space use patterns and habitat preferences. We examined the space use and habitat preferences of Black-necked Cranes during the winter of 2007-2008 at the Napahai wetland in northwest Yunnan, China, where approximately 300 Black-necked Cranes (>90% of the total central population) spent the winter. Euclidean distance analysis was employed to determine the habitat preferences of Black-necked Cranes, and a local nearest-neighbor, convex-hull construction method was used to examine space use. Our results indicate that Black-necked Cranes preferred shallow marsh and wet meadow habitats and avoided farmland and dry grassland. Core-use areas (50% isopleths) and total-use areas (100% isopleths) accounted for only 1.2% and 28.2% of the study area, respectively. We recommend that habitat protection efforts focus on shallow marsh and wet meadow habitats to maintain preferred foraging sites. Core-use areas, such as the primary foraging areas of Black-necked Cranes, should be designated as part of the core zone of the nature reserve. Monthly shifts in the core-use areas of the cranes also indicate that the reserve should be large enough to permit changes in space use. In addition to preserving habitat, government officials should also take measures to decrease human activity in areas used by foraging Black-necked Cranes.

Free-space optoelectronic switching cores with MPLS for SANs over WDM ring networks

With increasing demands on storage devices in the modern communication environment, the storage area network (SAN) has evolved to provide a direct connection allowing these storage devices to be accessed efficiently. To optimize the performance of a SAN, a three-stage hybrid electronic/optical switching node architecture based on the concept of a MPLS label switching mechanism, aimed at serving as a multi-protocol label switching (MPLS) ingress label edge router (LER) for a SAN-enabled application, has been designed. New shutter-based free-space multi-channel optical switching cores are employed as the core switch fabric to solve the packet contention and switching path conflict problems. The system-level node architecture design constraints are evaluated through self-similar traffic sourced from real gigabit Ethernet network traces and storage systems. The extension performance of a SAN over a proposed WDM ring network, aimed at serving as an MPLS-enabled transport network, is also presented and demonstrated. © 2012 OSA.

A plane symmetric 6R foldable ring

The design of a deployable structure which deploys from a compact bundle of six parallel bars to a rectangular ring is considered. The structure is a plane symmetric Bricard linkage. The internal mechanism is described in terms of its Denavit-Hartenberg parameters; the nature of its single degree of freedom is examined in detail by determining the exact structure of the system of equations governing its movement; a range of design parameters for building feasible mechanisms is determined numerically; and polynomial continuation is used to design rings with certain specified desirable properties. © 2013 Elsevier Ltd.