Interactive Atlas of habitability. Urban data management for the improvement of habitability and coexistence

In this paper we approximate to the understanding of the hybrid city as a context of changes, produced in the perception and in the modes of inhabiting and coexisting in cities through new technologies of information and communication.

Actualización de un compresor volumétrico alternativo

Este proyecto supone la actualización y modernización de un compresor volumétrico alternativo que se encuentra en el Laboratorio de Máquinas y Motores Térmicos. Para ello, el primer paso ha sido realizar una serie de adaptaciones físicas y electrónicas de las señales que producen los distintos transductores del compresor. Estas adaptaciones han sido necesarias para que las señales pudiesen ser reconocidas por el microcontrolador Arduino. Éste es el encargado de comunicar las señales a LabVIEW 2012 con el que se ha creado un programa de lectura e interpretación de datos. Después de que las señales pasen por dicho programa se obtiene la fuerza que está realizando el motor que mueve el compresor, la presión en cámara del compresor y las revoluciones por minuto a las que gira el eje del motor y por tanto, el compresor. ABSTRACT This project has carried out the updating and modernization of an alternative volumetric compressor located at the Laboratory of Heat Engines. To do so, the first step was to perform a series of physical and electronic adaptations of the signals produced by the different transducers of the compressor. These adjustments were necessary so that the signals could be recognized by the Arduino microcontroller. This is responsible for communicating signals to LabVIEW 2012, used to set up the reading and interpreting data program. Once the signals have passed through the aforementioned program, we obtain the data of the force generated by the motor driving the compressor, the pressure in the compressor chamber and the revolutions per minute of the motor’s rotating shaft, and therefore, the compressor.

Spatial divisions of society

The encounter of architecture and urbanism with parcelisation is marked with the sign of a historical debt. Parcelisation is a tremendously powerful design tool. Architecture and urban planning attest to its capacity to shape sociospatial relations across a range of scales and contexts. From Renaissance palazzi to modernist slabs, from nation-wide agrarian reforms and Haussmann’s Paris to Christopher Alexander’s new theory of urban design and Michael Webb’s Suitaloon — most of the historical revolutions and experimental projects that have shaken these fields have relied, consciously or not, on a critique and restructuration of inherited divisions of land and space. The layout of parcel patterns has a series of implications including forms of property, the divide between private and public realms, the distribution of spatial contents and uses through zoning, typological decisions and so forth. The behaviour of any urban structure depends on the tissue of plots that configures the urban fabric and many of the challenges urban design faces today —complexity, urban vitality, social equality, etc.— hinge upon the forms of land division and distribution we adopt.

LogIn Design City

LogIn Design City is a project for the revitalization of public city?s space through the involvement of individuals, collectivities and municipalities, managed by a specific team and structured upon an augmented platform. The management system permits the organization of self-managed events and actions, offering support and assistance for the implementation of these actions in the offered spots of the city. Actions can be of cultural, commercial, educational or leisure-oriented nature and depending on their purpose the spots can be offered free of charge or with fees, creating a possibility for remuneration and providing a tool for development in underprivileged zones of the city. An important aspect is the emphasis on the digital outlook of the city, which is structured as an interface that allows communication with the management system and information upon actual, past and upcoming events.

Telemetría de vehículos FSAE con microcontrolador PIC32 y transceptor de radio CC1101

Quizás el campo de las telecomunicaciones sea uno de los campos en el que más se ha progresado en este último siglo y medio, con la ayuda de otros campos de la ciencia y la técnica tales como la computación, la física electrónica, y un gran número de disciplinas, que se han utilizado estos últimos 150 años en conjunción para mejorarse unas con la ayuda de otras. Por ejemplo, la química ayuda a comprender y mejorar campos como la medicina, que también a su vez se ve mejorada por los progresos en la electrónica creados por los físicos y químicos, que poseen herramientas más potentes para calcular y simular debido a los progresos computacionales. Otro de los campos que ha sufrido un gran avance en este último siglo es el de la automoción, aunque estancados en el motor de combustión, los vehículos han sufrido enormes cambios debido a la irrupción de los avances en la electrónica del automóvil con multitud de sistemas ya ampliamente integrados en los vehículos actuales. La Formula SAE® o Formula Student es una competición de diseño, organizada por la SAE International (Society of Automotive Engineers) para estudiantes de universidades de todo el mundo que promueve la ingeniería a través de una competición donde los miembros del equipo diseñan, construyen, desarrollan y compiten en un pequeño y potente monoplaza. En el ámbito educativo, evitando el sistema tradicional de clases magistrales, se introducen cambios en las metodologías de enseñanza y surge el proyecto de la Fórmula Student para lograr una mejora en las acciones formativas, que permitan ir incorporando nuevos objetivos y diseñar nuevas situaciones de aprendizaje que supongan una oportunidad para el desarrollo de competencias de los alumnos, mejorar su formación como ingenieros y contrastar sus progresos compitiendo con las mejores universidades del mundo. En este proyecto se pretende dotar a los alumnos de las escuelas de ingeniería de la UPM que desarrollan el vehículo de FSAE de una herramienta de telemetría con la que evaluar y probar comportamiento del vehículo de FSAE junto con sus subsistemas que ellos mismos diseñan, con el objetivo de evaluar el comportamiento, introducir mejoras, analizar resultados de una manera más rápida y cómoda, con el objetivo de poder progresar más rápidamente en su desarrollo, recibiendo y almacenando una realimentación directa e instantánea del funcionamiento mediante la lectura de los datos que circulan por el bus CAN del vehículo. También ofrece la posibilidad de inyectar datos a los sistemas conectados al bus CAN de manera remota. Se engloba en el conjunto de proyectos de la FSAE, más concretamente en los basados en la plataforma PIC32 y propone una solución conjunta con otros proyectos o también por sí sola. Para la ejecución del proyecto se fabricó una placa compuesta de dos placas de circuito impreso, la de la estación base que envía comandos, instrucciones y datos para inyectar en el bus CAN del vehículo mediante radiofrecuencia y la placa que incorpora el vehículo que envía las tramas que circulan por el bus CAN del vehículo con los identificadores deseados, ejecuta los comandos recibidos por radiofrecuencia y salva las tramas CAN en una memoria USB o SD Card. Las dos PCBs constituyen el hardware del proyecto. El software se compone de dos programas. Un programa para la PCB del vehículo que emite los datos a la estación base, codificado en lenguaje C con ayuda del entorno de desarrollo MPLAB de Microchip. El otro programa hecho con LabView para la PCB de la estación base que recibe los datos provenientes del vehículo y los interpreta. Se propone un hardware y una capa o funciones de software para los microcontroladores PIC32 (similar al de otros proyectos del FSAE) para la transmisión de las tramas del bus CAN del vehículo de manera inalámbrica a una estación base, capaz de insertar tramas en el bus CAN del vehículo enviadas desde la estación base. También almacena estas tramas CAN en un dispositivo USB o SD Card situado en el vehículo. Para la transmisión de los datos se hizo un estudio de las frecuencias de transmisión, la legislación aplicable y los tipos de transceptores. Se optó por utilizar la banda de radiofrecuencia de uso común ISM de 433MHz mediante el transceptor integrado CC110L de Texas Instruments altamente configurable y con interfaz SPI. Se adquirieron dos parejas de módulos compatibles, con amplificador de potencia o sin él. LabView controla la estación que recoge las tramas CAN vía RF y está dotada del mismo transceptor de radio junto con un puente de comunicaciones SPI-USB, al que se puede acceder de dos diferentes maneras, mediante librerías dll, o mediante NI-VISA con transferencias RAW-USB. La aplicación desarrollada posee una interfaz configurable por el usuario para la muestra de los futuros sensores o actuadores que se incorporen en el vehículo y es capaz de interpretar las tramas CAN, mostrarlas, gráfica, numéricamente y almacenar esta información, como si fuera el cuadro de instrumentos del vehículo. Existe una limitación de la velocidad global del sistema en forma de cuello de botella que se crea debido a las limitaciones del transceptor CC110L por lo que si no se desea filtrar los datos que se crean necesarios, sería necesario aumentar el número de canales de radio para altas ocupaciones del bus CAN. Debido a la pérdida de relaciones con el INSIA, no se pudo probar de manera real en el propio vehículo, pero se hicieron pruebas satisfactorias (hasta 1,6 km) con una configuración de tramas CAN estándar a una velocidad de transmisión de 1 Mbit/s y un tiempo de bit de 1 microsegundo. El periférico CAN del PIC32 se programará para cumplir con estas especificaciones de la ECU del vehículo, que se presupone que es la MS3 Sport de Bosch, de la que LabView interpretará las tramas CAN recibidas de manera inalámbrica. Para poder probar el sistema, ha sido necesario reutilizar el hardware y adaptar el software del primer prototipo creado, que emite tramas CAN preprogramadas con una latencia también programable y que simulará al bus CAN proporcionando los datos a transmitir por el sistema que incorpora el vehículo. Durante el desarrollo de este proyecto, en las etapas finales, el fabricante del puente de comunicaciones SPI-USB MCP2210 liberó una librería (dll) compatible y sin errores, por lo que se nos ofrecía una oportunidad interesante para la comparación de las velocidades de acceso al transceptor de radio, que se presuponía y se comprobó más eficiente que la solución ya hecha mediante NI-VISA. ABSTRACT. The Formula SAE competition is an international university applied to technological innovation in vehicles racing type formula, in which each team, made up of students, should design, construct and test a prototype each year within certain rules. The challenge of FSAE is that it is an educational project farther away than a master class. The goal of the present project is to make a tool for other students to use it in his projects related to FSAE to test and improve the vehicle, and, the improvements that can be provided by the electronics could be materialized in a victory and win the competition with this competitive advantage. A telemetry system was developed. It sends the data provided by the car’s CAN bus through a radio frequency transceiver and receive commands to execute on the system, it provides by a base station on the ground. Moreover, constant verification in real time of the status of the car or data parameters like the revolutions per minute, pressure from collectors, water temperature, and so on, can be accessed from the base station on the ground, so that, it could be possible to study the behaviour of the vehicle in early phases of the car development. A printed circuit board, composed of two boards, and two software programs in two different languages, have been developed, and built for the project implementation. The software utilized to design the PCB is Orcad10.5/Layout. The base station PCB on a PC receives data from the PCB connected to the vehicle’s CAN bus and sends commands like set CAN filters or masks, activate data logger or inject CAN frames. This PCB is connected to a PC via USB and contains a bridge USB-SPI to communicate with a similar transceiver on the vehicle PCB. LabView controls this part of the system. A special virtual Instrument (VI) had been created in order to add future new elements to the vehicle, is a dashboard, which reads the data passed from the main VI and represents them graphically to studying the behaviour of the car on track. In this special VI other alums can make modifications to accommodate the data provided from the vehicle CAN’s bus to new elements on the vehicle, show or save the CAN frames in the form or format they want. Two methods to access to SPI bus of CC110l RF transceiver over LabView have been developed with minimum changes between them. Access through NI-VISA (Virtual Instrument Software Architecture) which is a standard for configuring, programming, USB interfaces or other devices in National Instruments LabView. And access through DLL (dynamic link library) supplied by the manufacturer of the bridge USB-SPI, Microchip. Then the work is done in two forms, but the dll solution developed shows better behaviour, and increase the speed of the system because has less overload of the USB bus due to a better efficiency of the dll solution versus VISA solution. The PCB connected to the vehicle’s CAN bus receives commands from the base station PCB on a PC, and, acts in function of the command or execute actions like to inject packets into CAN bus or activate data logger. Also sends over RF the CAN frames present on the bus, which can be filtered, to avoid unnecessary radio emissions or overflowing the RF transceiver. This PCB consists of two basic pieces: A microcontroller with 32 bit architecture PIC32MX795F512L from Microchip and the radio transceiver integrated circuit CC110l from Texas Instruments. The PIC32MX795F512L has an integrated CAN and several peripherals like SPI controllers that are utilized to communicate with RF transceiver and SD Card. The USB controller on the PIC32 is utilized to store CAN data on a USB memory, and change notification peripheral is utilized like an external interrupt. Hardware for other peripherals is accessible. The software part of this PCB is coded in C with MPLAB from Microchip, and programming over PICkit 3 Programmer, also from Microchip. Some of his libraries have been modified to work properly with this project and other was created specifically for this project. In the phase for RF selection and design is made a study to clarify the general aspects of regulations for the this project in order to understand it and select the proper band, frequency, and radio transceiver for the activities developed in the project. From the different options available it selects a common use band ICM, with less regulation and free to emit with restrictions and disadvantages like high occupation. The transceiver utilized to transmit and receive the data CC110l is an integrated circuit which needs fewer components from Texas Instruments and it can be accessed through SPI bus. Basically is a state machine which changes his state whit commands received over an SPI bus or internal events. The transceiver has several programmable general purpose Inputs and outputs. These GPIOs are connected to PIC32 change notification input to generate an interrupt or connected to GPIO to MCP2210 USB-SPI bridge to inform to the base station for a packet received. A two pair of modules of CC110l radio module kit from different output power has been purchased which includes an antenna. This is to keep away from fabrication mistakes in RF hardware part or designs, although reference design and gerbers files are available on the webpage of the chip manufacturer. A neck bottle is present on the complete system, because the maximum data rate of CC110l transceiver is a half than CAN bus data rate, hence for high occupation of CAN bus is recommendable to filter the data or add more radio channels, because the buffers can’t sustain this load along the time. Unfortunately, during the development of the project, the relations with the INSIA, who develops the vehicle, was lost, for this reason, will be made impossible to test the final phases of the project like integration on the car, final test of integration, place of the antenna, enclosure of the electronics, connectors selection, etc. To test or evaluate the system, it was necessary to simulate the CAN bus with a hardware to feed the system with entry data. An early hardware prototype was adapted his software to send programed CAN frames at a fixed data rate and certain timing who simulate several levels of occupation of the CAN Bus. This CAN frames emulates the Bosch ECU MS3 Sport.

DE UMA CRISE A OUTRA, DE UM DARWINISMO A OUTRO: A IMPLANTAÇÃO DA PROGRESSÃO CONTINUADA NO ESTADO DE SÃO PAULO

O presente trabalho investiga a implantação do regime de progressão continuada nas escolas públicas do estado de São Paulo em 1998, de modo que tem como eixo de pesquisa e reflexões a política pública progressão continuada e seu processo de implantação e implementação. Houve o uso de duas linhas de pesquisa: pesquisa bibliográfica e pesquisa e análise do discurso oficial, não somente aquele que implanta o regime citado, mas também a gradação das leis e suas características. O suporte central de pesquisa apoia-se em duas consagradas obras: “A estrutura das revoluções científicas” e “A origem das espécies”, de Thomas Kuhn e Charles Darwin, respectivamente. As obras citadas farão jus ao título desse trabalho, a qual utiliza das discussões propostas por Kuhn sobre ‘crise’, tendo esta como uma das linhas mestras para analisar os períodos pré e pós implantação do regime combinado ao darwinismo, que aqui se denomina darwinismo pedagógico. Para estabelecer uma conexão entre o objeto central de pesquisa e as obras acima citadas, houve a necessidade de pesquisar e discutir temáticas diretamente relacionadas, como ‘um rio e seus afluentes’. Os ‘afluentes’ pesquisados e discutidos foram: pedagogia e ciência, regime de seriação, darwinismo, metáfora, políticas públicas, gradação das leis, identidade, resistência e desistência. Os ‘afluentes’ não ficaram restritos a pesquisa bibliográfica, houve a necessidade de também no discurso oficial realizar esta linha metodológica. A pesquisa revelou que a partir das contribuições de Kuhn, a implantação do regime de progressão continuada nas escolas públicas do estado de São Paulo apenas fez com que a educação no estado saísse de uma crise e entrasse em outra. Além disso, revelou também que o darwinismo pedagógico que imperava no regime de seriação, muda de face no regime de progressão continuada, porém continua ativo, agora afetando diretamente os docentes, que resistem ativamente ou em oposição, ou desistem, seja de forma anunciada ou velada.

Genetic evidence for different male and female roles during cultural transitions in the British Isles

Human history is punctuated by periods of rapid cultural change. Although archeologists have developed a range of models to describe cultural transitions, in most real examples we do not know whether the processes involved the movement of people or the movement of culture only. With a series of relatively well defined cultural transitions, the British Isles present an ideal opportunity to assess the demographic context of cultural change. Important transitions after the first Paleolithic settlements include the Neolithic, the development of Iron Age cultures, and various historical invasions from continental Europe. Here we show that patterns of Y-chromosome variation indicate that the Neolithic and Iron Age transitions in the British Isles occurred without large-scale male movements. The more recent invasions from Scandinavia, on the other hand, appear to have left a significant paternal genetic legacy. In contrast, patterns of mtDNA and X-chromosome variation indicate that one or more of these pre-Anglo-Saxon cultural revolutions had a major effect on the maternal genetic heritage of the British Isles.

Digital Fabrication and Free Culture. One More Minor Becoming?

Diferentes autores se refieren a la fabricación digital como la Tercera Revolución Digital, después de las revoluciones de la computación y la comunicación. Como ocurriera con las dos revoluciones precedentes, se generaron grandes expectativas en torno a las virtualidades políticas de estas nuevas tecnologías para dar lugar a relaciones de producción más libres e individuos más autónomos. Sin embargo, como también ocurriera con la computación y la comunicación, lo que realmente está ocurriendo demuestra que las supuestas virtualidades no llegarán a hacerse actuales sin una intensa implicación, organización y trabajo por parte de sectores activistas técnicos y sociales. Se discute el caso de la compra corporativa de la empresa pionera de hardware libre Makerbot, como ejemplo de la situación y punto de inflexión en las expectativas de los nuevos tecno-visionarios. Para concluir se propone una serie de posibles estrategias que podrían promover el desarrollo efectivo de un ecosistema libre y open source de fabricación digital.

A revolução de 14 de Maio de 1915: justificações e dinâmicas

Este trabalho pretende dar uma visão historiográfica aprofundada sobre um dos acontecimentos mais dramáticos ocorridos durante a vigência da I Republica Portuguesa: A Revolução de 14 de Maio de 1915. Este movimento foi o mais violento durante os dezasseis anos em que durou a I República. Segundo a imprensa contemporânea, liquidou-se em duzentos mortos e mil feridos. As consequências directas da revolução ditaram o fim do Governo do general Pimenta de Castro (foi a primeira tentativa, antes do golpe Sidonista em 1917, de inverter o domínio do Partido Republicano Português sobre as instituições governamentais). Ao longo deste trabalho, abordamos as origens do movimento revolucionário de 14 de Maio de 1915, dedicando especial atenção ao impacto do Governo do general Pimenta de Castro, apontando as suas principais linhas de força, que promoveu a organização e a execução do movimento durante a madrugada do dia 14 de Maio de 1915. Aborda-se também os factos ocorridos ao longo desse dia e nos dias seguintes em Lisboa, na Margem Sul, no Porto e na Província. Por último, expomos as principais consequências que o movimento teve.

The Arab Spring: where was the EU, and what is its future in the region? Jean Monnet/Robert Schuman Paper Series Vol. 13 No. 4, February 2013

From the Introduction. In 2010 the martyring of Mohamed Bouazizi began a ripple of civil uprisings across the Middle East, and would lead to a wave of revolutions that the media would dub the Arab Spring. From North Africa to the Gulf Region, these civil uprisings made major headlines but found little intervention on behalf of world superpowers such as the United States or the European Union. Acting as more of an observer than as an active participant in these revolutions, it would seem that the European Union played a small role in preventing civil unrest, or in aiding in the policing of these oppressive governments. By example of the passive position held by Europe during these revolutions, the EU appears to be ill equipped to handle security issues such as the massive revolutionary chain witnessed across the Mediterranean. Now, however, they have a new opportunity to be involved in a post- Arab Spring Mediterranean. This paper seeks to address some reasons behind the Arab Spring, describe the institutional framework previously and currently in place, as well as to analyze the progress of Europe’s relationship with the Mediterranean by analyzing the EU’s past and current role in the Mediterranean. It will also look at critiques of the EU’s role in the Arab Spring, as well as the opportunities to be taken in the Mediterranean region.

The ‘Unknown Knowns’ of the Global Gas Market. CEPS Essay No. 16, 16 October 2014

Energy markets evolve at least as quickly as the economies they fuel. But development unfolds at an irregular pace, with starts and stops often precipitated by seemingly unpredictable dynamics. Is it really impossible to forecast these ‘revolutions���, if the past can be seen as prologue? The answer might be in the way we look at future events; even if we accept that some events are unpredictable, we may be able to infer much more about the future trends through a broader reading of available data, thus revealing ‘unknown knowns’ that may be useful in understanding paradigm shifts ahead. This paper presents an analysis of the global gas market, offering views on what the most relevant ‘unknown knowns’ of today look like, and hypotheses about some of the possible game-changing events that the market is likely to face in the short to medium term.

Integration or imitation? EU policy towards its Eastern neighbours. OSW Study 36/2011

Does the European Union’s policy towards its Eastern neighbours have any chance of success? To what extent can the objective of ‘external integration’, i.e. the adoption of EU standards by its Easternneighbours, be achieved? The European Neighbourhood Policy is currently being reviewed and the revolutions in North Africa have triggered a fresh debate on this policy. Alongside this process, Poland's forthcoming presidency of the EU (given that Poland grants high priority to rapprochement with its Eastern neighbours) provides yet another pretext for posing the above questions. However, these considerations extend beyond current events and the EU calendar. There are aspects of the central question, namely: Is the EU capable of exporting its own model of governance? This question is currently more focused on the local than the global potential of the European Union. Can it continue the process of ‘making Europe wider’?

Tug-of-war over EU's policy towards its neighbours. OSW Commentary No. 49, 2011-03-09

The revolutions in North Africa, the approaching end of the ‘strategic review’ of the European Neighbourhood Policy (ENP) initiated by the European Commission, and the beginning of negotiations on the European Union’s new financial perspective, have intensified the debate among the member states and EU institutions on what policy the EU will adopt towards its neighbourhood in the future. The discussion concerns not only the shape of the ENP but also non-ENPI foreign policy instruments which Brussels applies towards neighbouring countries, such as the thematic instruments and loan support. Serious differences of opinion have emerged among the member states. The countries located in the southern part of the EU want Brussels to boost its policy towards North Africa, even at the expense of engagement in Eastern Europe and the Southern Caucasus. Meanwhile Central European countries, including Germany, favour a more balanced approach towards both directions. The future shape of the ENP, as well as the EU’s other foreign policy instruments, will have a strong impact on the approach the EU adopts towards its Eastern neighbourhood. If some of the proposals are realised, especially the southern member states’ request to transfer some of the funds from the Eastern to the Southern neighbourhood, the chances of meeting the Eastern Partnership goals, such as the association of the partner countries with the EU and the creation of deep and comprehensive free trade areas, could be reduced.

Demographic situation in Russia. OSW Study 24/2006

Throughout the history of Russia, periods of deep chaos have been accompanied by demographic crises. This was the case during the Time of Troubles, or Smutnoye Vremya, in the seventeenth century, and during the period of wars and revolutions in the early twentieth century, which brought the Bolsheviks to power. Similarly, the break-up of the USSR also coincided with a demographic crisis. However, while the previous crises had been caused by factors such as war, famine, epidemics or repressive policies, and were followed by periods of rapid population growth once these factors had ceased to operate, the current crisis is systemic and structural. To a large extent, it has been occasioned by cultural factors such as changing family models and the roles of women in today's society. In Russia, the effect of these factors on population increase is exacerbated by excessive alcohol consumption, an culture of inadequate working conditions which leads to many accidents at work, and healthcare deficiencies (only c. 3% of the GDP is spent on healthcare annually).

Supporting the Revolution: America, Democracy, and the End of the Cold War in Poland, 1981-1989. ACES Working Paper (Report) No. 8, 2007

Early on the morning of December 13, 1981, General Wojciech Jaruzelski, the leader of the communist Polish United Workers' Party (PZPR), declared martial law, ending the so-called "Polish Crisis," which began with the creation of the Independent Free Trade Union "Solidamosc" in August 1980. Over the next eight years, the Communist government and the opposition struggled over power, culminating in 1989 with the creation of a Solidamosc-led government which ended fifty years of Communist rule in Poland and led the way to further democratic revolutions throughout Eastern Europe. The purpose of this dissertation is to utilize newly available and underutilized archival sources as well as oral history interviews, from both international and American perspectives, to fully chronicle American policy toward Poland from the declaration of martial law until the creation of the Solidarnosc government. Rather than explaining Polish-American relations in bilateral terms, the dissertation illuminates the complex web of influences that determined American policy in Washington and affected its implementation within Poland. This includes descriptions of internal tensions within the Reagan administration, differences between American decisions in Washington and implementation in Warsaw, lobbying from Polish-American groups, clashes between Capitol Hill and the White House, coordination with American labor organizations to support Solidarnosc, disagreements with West European allies in NATO and international financial organizations, cooperation with the Vatican and the Polish Catholic Church, synchronization with American humanitarian organizations working in Poland, limitations caused by the realities of Soviet power in Eastern Europe, and complications caused by domestic Polish concerns. By taking a broad view of American policy and highlighting internal Polish decisions, with both the Communist government and the democratic opposition, the dissertation provides concrete examples of America's role in Poland's transformation, arguing, however, that this role was very limited. These conclusions are relevant to arguments about the end of the Cold War, the nature of American power, as well as current discussions about possibilities to promote democracy within hostile regimes.