Lasing behavior in DCM-doped PVK microcavity

A surface emitting microcavity was formed by sandwiching a polymer film containing PVK, Alq(3) and DCM between a distributed Bragg reflector (DBR) with a reflectivity of 99% and a silver film (300 nm). The lasing phenomenon was observed in DCM-doped PVK microcavity. The full width at half maximum (FWHM) was 0.6 nm with the peak wavelength at 603 nm. The threshold energy for lasing was estimated to be about 2.5 mu J per pulse. (C) 2000 Published by Elsevier Science S.A. All rights reserved.

Photoluminescent properties of dye-doped poly(N-vinyleabzole) (PVK) in microcavity

A surface emitting microcavity was formed by sandwiching a polymer film containing poly(N-vinyleabzole) (PVK). 8-hydroxyquinoline aluminium (Alq(3)) and 4-(Dicyanome thylene)-2-methyl-6-(4-dimethylaminostyryl)-4H-Pyran(DCM) between a distributed Bragg reflector (DBR) with a reflectivity of 99% and a silver film. The sample was optically pumped with 250 ps pulses at 2 Hz repetition rate by a 355 nm line of the third harmonic of a mode-lock Nd:YAG laser. The lasing phenomenon was observed in DCM-doped PVK microcavity. The full width at half maximum (FWHM) was 3 nm with the peak wavelength at 602 nm. The threshold energy for lasing was estimated to be about 3 mu J. (C) 2000 Elsevier Science S.A. All rights reserved.

Confined crystallization behavior of PEO in organic networks

Poly (ethylene oxide) (PEO) and poly (trimethopropane trimethacrylate) (PTMPTMA) interpenetrate networks have been synthesized. The confined crystallization behavior of PEO in the PTMTYTMA networks has been investigated by a differential scanning calorimeter and scanning electron microscope. The degree of PEO crystallinity in PEO/PTMPTMA interpenetrate networks reduces with the increase of PTMPTMA. PEO is in an amorphous state when the concentration of PEO is lower than 50% in the interpenetrate networks system. The melting points of crystalline PEO in the networks are lower than that of pure PEG, and the melting point of PEO in the networks is higher and increases with the increase of PEO in the interpenetrate networks. Wide-angle X-ray diffraction results show that the PEO crystallite size perpendicular to the (120) plane is not affected as much as PEO in silica networks. (C) 2001 Elsevier Science Ltd. All rights reserved.

Surface roughness characterization of soft x-ray multilayer films on the nanometer scale

The soft x-ray reflectivity of multilayer films is affected by the surface roughness on the transverse nanometer scale. Scanning tunneling microscopy (STM) is an ideal instrument for providing high-lateral-resolution roughness measurements for soft x-ray multilayer films that cannot be obtained with other types of instruments on the transverse nanometer scale. The surface roughnesses of Mo/Si, Mo/C, and W/Si soft x-ray multilayer films prepared by an ion-beam-sputtering technique were measured with a STM on the vertical and transverse attributes. The film roughnesses and average spatial wavelengths added to the substrates depend on the multilayer film fabrication conditions, i.e., material combinations, number of layers, and individual layer thickness. These were estimated to lead to a loss of specular reflectivity and variations of the soft x-ray scattering angle distribution. This method points the way to further studies of soft x-ray multilayer film functional properties and can be used as basic guidance for selecting the best coating conditions in the fabrications of soft x-ray multilayer films. (C) 1996 American Vacuum Society.

三维VSP技术的研究及应用

Today, because of high petroleum consumption of our country, society steady development and difficulty increase in new resources exploration, deep exploitation of the existing oilfield is needed. More delicate reservoir imaging and description, such as thin layer identification, interlayer exploitation monitoring, subtle structure imaging, reservoir anisotropy recognition, can provide more detail evidence for new development adjustment scheme and enhanced oil recovery. Now, the people have already realized the 3D VSP technique more effective than the general methods in solving these aspects. But VSP technique especially 3D VSP develop slowly due to some reasons. Carrying out the research of VSP technique, it will be very useful to the EOR service. 3D VSP techniques include acquisition、data processing and interpretation. In this paper, the author carried out some researches around acquisition and processing. The key point of acquisition is the survey design, it is critical to the quality of the data and it will influence the reservoir recognition as follows. The author did detailed researches on the layout pattern of shot point and geophone. Some attributes relate to survey design such as reflectivity, incidence angle, observation area, reflection points distribution, fold, minimum well source distance, azimuth angle and so on are studied seriously. In this geometry design of 3D-VSP exploration in deviated wells, the main problems to be solved are: determining the center position of shots distribution, the effect of shots missing on coverage areas and coverage times，locating the shots and receivers of multi-wells. Through simulating and analyzing, the above problems are discussed and some beneficial conclusions are drawn. These will provide valuable references to actual survey design. In data processing, researches emphasize on those relatively key techniques such as wavefield separation, VSP-CDP imaging, the author carried out deep researches around these two aspects. As a result, variant apparent slowness wavefield separation method developed in this article suit the underground variant velocity field and make wavefield separation well, it can overcome reflection bending shortage aroused by conventional imaging method. The attenuateion range of underground seismic wave is very important for amplitude compensation and oil/gas identification.In this paper, seismic wave attenuateion mechanism is studied by 3D-VSP simulateion and Q-inversion technique. By testing with seismic data, the method of VSP data attenuateion and relationship of attenuateion attribute variant with depth is researched. Also the software of survey design and data processing is developed, it fill the gap of VSP area in our country. The technique developed applied successfully in SZXX-A Oilfield、QKYY-B Oilfield、A area and B area. The good results show that this research is valuable, and it is meaningful to the VSP technique development and application of offshore oil industry and other areas in our country.

砂泥岩薄互层储层预测方法与应用研究

With the deeply development of exploration and development in petroleum in China, new increasing reserves are found in old oil fields and the verge of the old ones through re-study of geological property. It is more and more important to discovery and develop thin layer or thin inter-bedded layers reservoirs. All of the targets are thin sand-shale inter-bedded reservoirs and the core technology is reservoir predictions between wells in thin sand-shale inter-bedded layers. The continuity of the thin sand-shale inter-bedded layers in space or separating and heterogeneity is the key of reservoir geology research. The seismic reflection, high resolution analysis method and inversion method to thin sand-shale inter-bedded layers are thorough discussed and deeply studied in this paper to try to find the methods and resolutions of reservoir geology research. The below is followed. 1. Based on the pre-research of other people, five models are created: the sand sphenoid body, interlay sandstone and interlay shale of the equal thickness, interlay sandstone of the equal thickness and interlay shale of the unequal thickness, interlay sandstone of the unequal thickness and interlay shale of the unequal thickness, interlay sandstone of the changing thickness in sequence and interlay shale of the changing thickness in sequence. Then the study of the forward modeling are conducted on the thin layer and thin inter-bedded layers geological characters and seismic reflections including amplitude, frequency, phase, wave shape and time-frequency responding in the domains of time and frequency. The affect of petro-physics difference of layers, single thin layer thickness, thickness of inter-bedded, layer number of inter-bedded, incident wavelet domain frequency and types, sample interval to seismic reflection characters, frequency spectrum and time-frequency respond of reflectivity is theoretically discussed. 2. Qualitatively analyzing the sedimentary rhythm of the thin inter-bedded layers in vertical orientation and computing the single layer thickness or the average thickness with the method of generalized S transform. Identifying the reflecting interface or lithology interface using the amplitude value of amplitude spectrum domain frequency. 3. Based on the seismic respond of thin sand-shale inter-bedded layers, bring out the high resolution analysis method of seismic data in thin sand-shale inter-bedded layers using wavelet analysis and the idea of affecting low and high frequency with middle frequency. Then analyzing the effect to the method and testing some wavelets in the method. This method is applied to the theoretical models and the field data. 4. Bring forward one improved very fast simulated annealing method (IVFSA) to resolve the problem nonlinearity and multi-parameters of the inversion in thin inter-bedded layers. And IVFSA is more productive and higher precision than general ways. 5. New target constrained function is used in the inversion based on the property of the inversion in thin inter-bedded layers. 6. Making the full use of geological and logging information, IVFSA and the new function are applied in the non-linear inversion to improve reservoir prediction and evaluation in thin inter-bedded formations combined with the idea of logging and seismic inversion. This method was applied to the field data and got good results.

裂缝型储层检测方法——P波方位各向异性技术

Nowadays, the exploration of fractured reservoir plays a vital role in the further development of petroleum industry through out the world. Fractured hydrocarbon reservoirs are widely distributed in China. Usually, S-wave technique prevails, but it also has its disadvantage, prohibitive expense in S-wave data acquisition and processing. So directly utilizing P-wave data to detect fractures, comes to our mind. We briefly introduce theoretical model (HTI) for fractured reservoir. Then study Ruger’s reflectivity method to recognize reflection P-wave reflection coefficient of the top and bottom interface of HTI layer respectively, and its azimuth anisotropy character. Base on that study, we gives a review and comparison of two seismic exploration technologies for fractures available in the industry-- P-wave AVO and AVA. They has shown great potential for application to the oil and gas prediction of fractured reservoir and the reservoir fine description．Every technique has its disadvantage, AVO limited to small reflection angle; and AVA just offering relatively results. So that, We can draw a conclusion that a better way to any particular field is using synthesis of multiple data sources including core、outcrop、well-test、image logs、3D VSPs, generally to improve the accuracy.

岩性油藏储层预测的地震理论与方法研究

At present the main object of the exploration and development (E&D) of oil and gas is not the structural oil-gas pools but the subtle lithological oil-gas reservoir. Since the last 90's, the ratio of this kind of pools in newly-added oil reserves is becoming larger and larger, so is the ratio in the eastern oilfields. The third oil-gas resource evaluation indicates the main exploration object of Jiyang depression is the lithological oil-gas pools in future. However, lack of effective methods that are applied to search for this kind of pool makes E&D difficult and the cost high. In view of the urgent demand of E&D, in this paper we deeply study and analyze the theory and application in which the seismic attributes are used to predict and describe lithological oil-gas reservoirs. The great results are obtained by making full use of abundant physics and reservoir information as well as the remarkable lateral continuity involved in seismic data in combination with well logging, drilling-well and geology. ①Based on a great deal of research and different geological features of Shengli oilfield, the great progresses are made some theories and methods of seismic reservoir prediction and description. Three kinds of extrapolation near well seismic wavelet methods-inverse distance interpolation, phase interpolation and pseudo well reflectivity-are improved; particularly, in sparse well area the method of getting pseudo well reflectivity is given by the application of the wavelet theory. The formulae for seismic attributes and coherent volumes are derived theoretically, and the optimal method of seismic attributes and improved algorithms of picking up coherent data volumes are put forward. The method of making sequence analysis on seismic data is put forward and derived in which the wavelet transform is used to analyze not only qualitatively but also quantitatively seismic characteristics of reservoirs.② According to geologic model and seismic forward simulation, from macro to micro, the method of pre- and post-stack data synthetic analysis and application is put forward using seismic in close combination with geology; particularly, based on making full use of post-stack seismic data, "green food"-pre-stack seismic data is as possible as utilized. ③ In this paper, the formative law and distributing characteristic of lithologic oil-gas pools of the Tertiary in Jiyang depression, the knowledge of geological geophysics and the feasibility of all sorts of seismic methods, and the applied knowledge of seismic data and the geophysical mechanism of oil-gas reservoirs are studied. Therefore a series of perfect seismic technique and software are completed that fit to E&D of different categories of lithologic oil-gas reservoirs. ④ This achievement is different from other new seismic methods that are put forward in the recent years, that is multi-wave multi-component seismic, cross hole seismic, vertical seismic, and time-lapse seismic etc. that need the reacquisition of seismic data to predict and describe the oil-gas reservoir. The method in this paper is based on the conventional 2D/3D seismic data, so the cost falls sharply. ⑤ In recent years this technique that predict and describe lithologic oil-gas reservoirs by seismic information has been applied in E&D of lithologic oil-gas reservoirs on glutenite fans in abrupt slop and turbidite fans in front of abrup slop, slump turbidite fans in front of delta, turbidite fans with channel in low slope and channel sanbody, and a encouraging geologic result has been gained. This achievement indicates that the application of seismic information is one of the most effective ways in solving the present problem of E&D. This technique is significant in the application and popularization, and positive on increasing reserves and raising production as well as stable development in Shengli oilfield. And it will be directive to E&D of some similar reservoirs

内陆湖沼相和近海沼泽相沉积环境煤中微量元素和矿物的对比研究—以辽宁北票、江西建新和桥头煤研究为例

Using knowledge of geology, geochemistry, coal petrology, mineralogy, by means of a variety of advanced measuring methods such as inductively coupled plasma mass spectrometry (ICP-MS), inductively coupled atomic emission spectrometry (ICP-AES), X-ray powder diffraction (XRD), scanning electron microscopy with energy-dispersive spectrometer(SEM-EDS), sequential chemical extract and density fractions, the characteristics of trace elements and minerals in Jurassic Beipiao coal mine under inland limnetic sedimentary environment and in late Permian Jianxin and Qiaotou coal mines under paralic swamp sedimentary environment were studied. Compared with the average concentration in the world bituminous coals, the Beipiao coal was characterized by relatively high contents of Sc, Ti, Cr, Co, Ni, Zn, Se, Sr, Zr, Y, Ba, REE and Th, and lower contents of V, Rb, Cd, Sn, Pb, Bi and U; while the Jianxin coal was relatively enriched in Li, Sc, Ga, Sr, Y, Nb, Sb, Th and U, with low concentration of Be, Co, Ni, Cu, Ge, Zr, Mo, Cd, Cs, Ba, Pb and Bi; and the Qiaotou coal was enriched in Li, Sc, Sr, Nb, Ta, Zr, REE, Hf, Th and U, with low concentration of Be, V, Co, Ni, Cu, Ge, Mo, Cd, Cs, Ba, Tl, Pb and Bi. The concentrations of Ca, Mg and K in Beipiao coal are higher than those in Jianxin coal and Qiaotou coal, while Fe, S and Ti in Beipiao coal are lower than those in Jianxin coal and Qiaotou coal. The proximate analysis of coal samples was carried out, which indicated that Beipiao coal was medium- to high- ash (5.92-60.68%) with low sulphur coal, and Jianxin coal and Qiaotou coal was medium to high ash (8.85-46.33%) with high sulphur. The reflectivity was measured, which explained that Beipiao coal belonged to high volatile bituminous coal, Jianxin coal was low volatile bituminous coal and Qiaotou coal was low volatile anthracite. Quantitative maceral analyses were studied. The characteristics of rare earth elements (REE) were investigated, which showed that the total contents of REE were higher than that of the world's average content. With the increase of coal's metamorphic grade, the total contents of REE decreased from 98.5 X 10"6 of Beipiao coal to 94.2 X 10"6 of Jianxin coal, and to 75.9 X 10"6 of Qiaotou coal, and 5Eu reduced which indicated that the element Eu depleted. The characteristics of REE was controlled by the metamorphic grade of coal. And REE were mainly absorbed in clay minerals in Beipiao coal samples, while in Jianxin and Qiaotou coal mines, REE were primarily related to clay mineral and pyrite. The variation of trace elements in vertical direction of coal seams was studied, and the results showed that different trace elements differed greatly. The correlation between trace elements and ash were determined. Four major trace elements (aluminium-silicates, sulphide, carbonate and phosphate) accounted for the occurrence and distribution of most elements studied were determined. Coal samples were separated by density fraction, which showed that Cr, Cu, Mo and Pb were closely related to inorganic matters mainly distributed in P >2.6 and dropped remarkably in the density fractions P <2.3 . The occurrences of Co, Cr, Ni, As, Se, Mo, U were studied directly and quantitatively using sequential chemical extract with six steps, which showed that Co. Ni, Mo and U were mainly in the form of mineral, and As, Se chiefly in the form of organic state, while Cr mostly in the form of organic state and mineral. Major mineral phases presented in the Beipiao coal were Kaolinite, illite, quartz, calcite, and small amount of siderite, barite. While major mineral phases in Jianxin and Qiaotou coal were pyrite, kaolinite, and small amount of marcasite, rutile, sphalerite. This is the first time that the chromite in the coal was discovered in China, which indicates that Cr occurrence appeared in the form of chromite. The ratio of Sr/Ba, Sr/Ca and V/Ni in Beipiao coal mine under inland limnetic is smaller than that of in Jianxin and Qiaotou coal mines under paralic swamp. The ratio of K/Na and Th/U of Beipiao coal mine is higher than that of Jianxin and Qiaotou coal mine, which proved that Beipiao coal was not affected by sea water and Jianxin and Qiaotou coal were affected by sea water. Trace elements such as Cr, Ni, Mo in minerals were analyzed by SEM-EDS. The factors controlling the enrichment of trace elements can be divided into syngenetic stage factors and epigenetic stage factors.

地震反射系数成像方法研究

Reflectivity sequences extraction is a key part of impedance inversion in seismic exploration. Although many valid inversion methods exist, with crosswell seismic data, the frequency brand of seismic data can not be broadened to satisfy the practical need. It is an urgent problem to be solved. Pre-stack depth migration which developed in these years becomes more and more robust in the exploration. It is a powerful technology of imaging to the geological object with complex structure and its final result is reflectivity imaging. Based on the reflectivity imaging of crosswell seismic data and wave equation, this paper completed such works as follows: Completes the workflow of blind deconvolution, Cauchy criteria is used to regulate the inversion(sparse inversion). Also the precondition conjugate gradient(PCG) based on Krylov subspace is combined with to decrease the computation, improves the speed, and the transition matrix is not necessary anymore be positive and symmetric. This method is used to the high frequency recovery of crosswell seismic section and the result is satisfactory. Application of rotation transform and viterbi algorithm in the preprocess of equation prestack depth migration. In equation prestack depth migration, the grid of seismic dataset is required to be regular. Due to the influence of complex terrain and fold, the acquisition geometry sometimes becomes irregular. At the same time, to avoid the aliasing produced by the sparse sample along the on-line, interpolation should be done between tracks. In this paper, I use the rotation transform to make on-line run parallel with the coordinate, and also use the viterbi algorithm to complete the automatic picking of events, the result is satisfactory. 1. Imaging is a key part of pre-stack depth migration besides extrapolation. Imaging condition can influence the final result of reflectivity sequences imaging greatly however accurate the extrapolation operator is. The author does migration of Marmousi under different imaging conditions. And analyzes these methods according to the results. The results of computation show that imaging condition which stabilize source wave field and the least-squares estimation imaging condition in this paper are better than the conventional correlation imaging condition. The traditional pattern of "distributed computing and mass decision" is wisely adopted in the field of seismic data processing and becoming an obstacle of the promoting of the enterprise management level. Thus at the end of this paper, a systemic solution scheme, which employs the mode of "distributed computing - centralized storage - instant release", is brought forward, based on the combination of C/S and B/S release models. The architecture of the solution, the corresponding web technology and the client software are introduced. The application shows that the validity of this scheme.

Ubuntu and the Obligation to Obey the Law

Nkiruka, M., Ubuntu and the Obligation to Obey the Law, Cambrian Law Review. Vol. 37. 2006. p. 17 RAE2008

Broadband cavity-enhanced absorption spectroscopy with incoherent light

Although broadband incoherent light does not efficiently couple into a high-finesse optical cavity, its transmission is readily detectable and enables applications in cavity-enhanced absorption spectroscopy in the gas phase, liquid phase and on surfaces. This chapter gives an overview of measurement principles and experimental approaches implementing incoherent light sources in cavity-enhanced spectroscopic applications. The general principles of broadband CEAS are outlined and general “pros and cons” discussed, detailing aspects like cavity mirror reflectivity calibration or the establishment of detection limits. Different approaches concerning light sources, cavity design and detection schemes are discussed and a comprehensive overview of the current literature based on a methodological classification scheme is also presented.

Surface plasmon resonance in nanostructured metal films under the Kretschmann configuration

We systematically investigated the surface plasmon resonance in one-dimensional (1D) subwavelength nanostructured metal films under the Kretschmann configuration. We calculated the reflectance, transmittance, and absorption for varying the dielectric fill factor, the period of the 1D nanostructure, and the metal film thickness. We have found that the small dielectric slits in the metal films reduce the surface plasmon resonance angle and move it toward the critical angle for total internal reflection. The reduction in surface plasmon resonance angle in nanostructured metal films is due to the increased intrinsic free electron oscillation frequency in metal nanostructures. Also we have found that the increasing the spatial frequency of the 1D nanograting reduces the surface plasmon resonance angle, which indicates that less momentum is needed to match the momentum of the surface plasmon-polariton. The variation in the nanostructured metal film thickness changes the resonance angle slightly, but mainly remains as a mean to adjust the coupling between the incident optical wave and the surface plasmon-polariton wave. © 2009 American Institute of Physics.

Facet-embedded thin-film III-V edge-emitting lasers integrated with SU-8 waveguides on silicon.

A thin-film InGaAs/GaAs edge-emitting single-quantum-well laser has been integrated with a tapered multimode SU-8 waveguide onto an Si substrate. The SU-8 waveguide is passively aligned to the laser using mask-based photolithography, mimicking electrical interconnection in Si complementary metal-oxide semiconductor, and overlaps one facet of the thin-film laser for coupling power from the laser to the waveguide. Injected threshold current densities of 260A/cm(2) are measured with the reduced reflectivity of the embedded laser facet while improving single mode coupling efficiency, which is theoretically simulated to be 77%.

Plankton and climate

Plankton has two roles with respect to climate: first as an indicator of climate change in present day populations and in the fossil record and second as a factor contributing to climate change through, for example, its role in the CO sub(2) cycle, in cloud formation via dimethylsulfide (DMS) production, and in altering the reflectivity of sea water as a component of suspended particulate matter. Current research on both the contribution of plankton to climate change and its role as an indicator of change are central to predicting potential scenarios that may occur in the future at a time when global mean temperatures are predicted to rise at an unprecedented rate by 1.5-6 degree C within the next 100 years.