Power management and power flow control with back-to-back converters in a utility connected microgrid

This paper proposes a method for power flow control between utility and microgrid through back-to-back converters, which facilitates desired real and reactive power flow between utility and microgrid. In the proposed control strategy, the system can run in two different modes depending on the power requirement in the microgrid. In mode-1, specified amount of real and reactive power are shared between the utility and the microgrid through the back-to-back converters. Mode-2 is invoked when the power that can be supplied by the DGs in the microgrid reaches its maximum limit. In such a case, the rest of the power demand of the microgrid has to be supplied by the utility. An arrangement between DGs in the microgrid is proposed to achieve load sharing in both grid connected and islanded modes. The back-to-back converters also provide total frequency isolation between the utility and the microgrid. It is shown that the voltage or frequency fluctuation in the utility side has no impact on voltage or power in microgrid side. Proper relay-breaker operation coordination is proposed during fault along with the blocking of the back-to-back converters for seamless resynchronization. Both impedance and motor type loads are considered to verify the system stability. The impact of dc side voltage fluctuation of the DGs and DG tripping on power sharing is also investigated. The efficacy of the proposed control ar-rangement has been validated through simulation for various operating conditions. The model of the microgrid power system is simulated in PSCAD.

Improvement of stability and load sharing in an autonomous microgrid using supplementary droop control loop

This paper investigates the problem of appropriate load sharing in an autonomous microgrid. High gain angle droop control ensures proper load sharing, especially under weak system conditions. However it has a negative impact on overall stability. Frequency domain modeling, eigenvalue analysis and time domain simulations are used to demonstrate this conflict. A supplementary loop is proposed around a conventional droop control of each DG converter to stabilize the system while using high angle droop gains. Control loops are based on local power measurement and modulation of the d-axis voltage reference of each converter. Coordinated design of supplementary control loops for each DG is formulated as a parameter optimization problem and solved using an evolutionary technique. The sup-plementary droop control loop is shown to stabilize the system for a range of operating conditions while ensuring satisfactory load sharing.

Load sharing and power quality enhanced operation of a distributed microgrid

This paper describes control methods for proper load sharing between parallel converters connected in a microgrid and supplied by distributed generators (DGs). It is assumed that the microgrid spans a large area and it supplies loads in both in grid connected and islanded modes. A control strategy is proposed to improve power quality and proper load sharing in both islanded and grid connected modes. It is assumed that each of the DGs has a local load connected to it which can be unbalanced and/or nonlinear. The DGs compensate the effects of unbalance and nonlinearity of the local loads. Common loads are also connected to the microgrid, which are supplied by the utility grid under normal conditions. However during islanding, each of the DGs supplies its local load and shares the common load through droop characteristics. Both impedance and motor loads are considered to verify the system response. The efficacy of the controller has been validated through simulation for various operating conditions using PSCAD. It has been found through simulation that the total Harmonic Distortion (THD) of the of the microgrid voltage is about 10% and the negative and zero sequence component are around 20% of the positive sequence component before compensation. After compensation, the THD remain below 0.5%, whereas, negative and zero sequence components of the voltages remain below 0.02% of the positive sequence component.

Fractions, reunitisation and the number-line representation

Centre for Mathematics and Science Education, QUT, Brisbane, Australia This paper reports on a study in which Years 6 and 10 students were individually interviewed to determine their ability to unitise and reunitise number lines used to represent mixed numbers and improper fractions. Only 16.7% of the students (all Year 6) were successful on all three tasks and, in general, Year 6 students outperformed Year 8 students. The interviews revealed that the remaining students had incomplete, fragmented or non-existent structural knowledge of mixed numbers and improper fractions, and were unable to unitise or reunitise number lines. The implication for teaching is that instruction should focus on providing students with a variety of fraction representations in order to develop rich and flexible schema for all fraction types (mixed numbers, and proper and improper fractions).

Experimental tests on structural members fabricated from high strength steel materials

Typical high strength steels (HSS) have exceptional high strengths with improved weldability making the material attractive in modern steel constructions. However, due to lack of understanding, most of the current steel design standards are limited to conventional low strength steels (LSS, i.e. fy ≤ 450 MPa). This paper presents the details of full-scale experimental tests on short beams fabricated from BISPLATE80 HSS materials (nominal fy = 690 MPa). The various slenderness ratios of the plate elements in the test specimens were chosen in the range near the current yield limit (AS4100-1998, etc.). The experimental studies presented in this paper have produced a better understanding of the structural behaviour of HSS members subjected to local instabilities. Comparisons have also presented in the paper regarding to the design predictions from the current steel standards (AS4100-1998). This study has enabled to provide a series of proposals for proper assessment of plate slenderness limits for structural members made of representative HSS materials. This research work also enables the inclusion of further versions in the steel design specifications for typical HSS materials to be used in buildings and bridges. This paper also presents a distribution model of residual stresses in the longitudinal direction for typical HSS I-sections.

Resistance : re-imagining innovation in higher education teaching and learning

The call to innovate is ubiquitous across the Australian educational policy context. The claims of innovative practices and environments that occur frequently in university mission statements, strategic plans and marketing literature suggest that this exhortation to innovate appears to have been taken up enthusiastically by the university sector. Throughout the history of universities, a range of reported deficiencies of higher education have worked to produce a notion of crisis. At present, it would seem that innovation is positioned as the solution to the notion of crisis. This thesis is an inquiry into how the insistence on innovation works to both enable and constrain teaching and learning practices in Australian universities. Alongside the interplay between innovation and crisis is the link between resistance and innovation, a link which remains largely unproblematized in the scholarly literature. This thesis works to locate and unsettle understandings of a relationship between innovation and Australian higher education. The aim of this inquiry is to generate new understandings of what counts as innovation within this context and how innovation is enacted. The thesis draws on a number of postmodernist theorists, whose works have informed firstly the research method, and then the analysis and findings. Firstly, there is an assumption that power is capillary and works through discourse to enact power relations which shape certain truths (Foucault, 1990). Secondly, this research scrutinised language practices which frame the capacity for individuals to act, alongside the language practices which encourage an individual to adopt certain attitudes and actions as one’s own (Foucault, 1988). Thirdly, innovation talk is read in this thesis as an example of needs talk, that is, as a medium through which what is considered domestic, political or economic is made and contested (Fraser, 1989). Fourthly, relationships between and within discourses were identified and analysed beyond cause and effect descriptions, and more productively considered to be in a constant state of becoming (Deleuze, 1987). Finally, the use of ironic research methods assisted in producing alternate configurations of innovation talk which are useful and new (Rorty, 1989). The theoretical assumptions which underpin this thesis inform a document analysis methodology, used to examine how certain texts work to shape the ways in which innovation is constructed. The data consisted of three Federal higher education funding policies selected on the rationale that these documents, as opposed to state or locally based policy and legislation, represent the only shared policy context for all Australian universities. The analysis first provided a modernist reading of the three documents, and this was followed by postmodernist readings of these same policy documents. The modernist reading worked to locate and describe the current truths about innovation. The historical context in which the policy was produced as well as the textual features of the document itself were important to this reading. In the first modernist reading, the binaries involved in producing proper and improper notions of innovation were described and analysed. In the process of the modernist analysis and the subsequent location of binary organisation, a number of conceptual collisions were identified, and these sites of struggle were revisited, through the application of a postmodernist reading. By applying the theories of Rorty (1989) and Fraser (1989) it became possible to not treat these sites as contradictory and requiring resolution, but rather as spaces in which binary tensions are necessary and productive. This postmodernist reading constructed new spaces for refusing and resisting dominant discourses of innovation which value only certain kinds of teaching and learning practices. By exploring a number of ironic language practices found within the policies, this thesis proposes an alternative way of thinking about what counts as innovation and how it happens. The new readings of innovation made possible through the work of this thesis were in response to a suite of enduring, inter-related questions – what counts as innovation?, who or what supports innovation?, how does innovation occur?, and who are the innovators?. The truths presented in response to these questions were treated as the language practices which constitute a dominant discourse of innovation talk. The collisions that occur within these truths were the contested sites which were of most interest for the analysis. The thesis concludes by presenting a theoretical blueprint which works to shift the boundaries of what counts as innovation and how it happens in a manner which is productive, inclusive and powerful. This blueprint forms the foundation upon which a number of recommendations are made for both my own professional practice and broader contexts. In keeping with the conceptual tone of this study, these recommendations are a suite of new questions which focus attention on the boundaries of innovation talk as an attempt to re-configure what is valued about teaching and learning at university.

Positioning public relations as an academic discipline in Australia

Academic public relations in Australia appears to be entering a new phase in its relatively short history. The early model, in which tertiary courses were confined to teaching – focused institutions and conducted largely by teacher-practitioners, is being supplanted by one in which the discipline is now offered in most Australian universities, is increasingly embracing research, and is being taught by staff following more traditional academic career paths. Despite the formal association with the communication discipline through Australian and New Zealand Communication Association, public relations academics have increasingly asserted the independence of their discipline and in reality have very little dialogue with the other strands of the communication discipline. These developments call into question the most appropriate knowledge base for public relations as an academic discipline in Australia and its proper relation to the profession (and the Public Relations Institute of Australia as the professional body). One danger associated with the assertion of disciplinary independence lies in the risk of excessive reliance on a relatively narrow body of work emanating from the more established United States public relations academy, in the process ignoring much richer work in surrounding disciplines such as social theory, rhetoric, organisation communication, and business and society. The emphasis on disciplinary demarcation also seems curious during a time of growing ‘interdisciplinarity’ in the humanities and the social sciences. This paper critically reviews the construction of public relations as an academic discipline in Australia, drawing on some of the literature on academic disciplinarity to propose a repositioning of the discipline, one that is less focused on asserting difference than on finding connections with other bodies of knowledge while maintaining close links with professional practice.

Supervising practice based research

Practice based research appears to have emerged within several Higher Education agendas including the professional doctorates and the teacher as researcher. One way of thinking about this methodological approach is to consider its research paradigm – a practice based epistemology, and from this perspective to consider what special application to research supervision the paradigm invites. Within a “supervision as pedagogy” agenda these applications can be considered as pedagogies. This paper has been written in the style of practice based research, drawing on the author’s own experiences of supervising students undertaking practice based research. It adopts a position that research supervision is pedagogy and draws on the model of ‘Productive Pedagogies” to articulate strategies to help novice research students develop a research proposal.

Distribution of benefits of irrigation induced technological changes and commodity markets : new evidence

A plethora of literature exists on irrigation development. However, only a few studies analyse the distributional issues associated with irrigation induced technological changes (IITC) in the context of commodity markets. Furthermore, these studies deal with only the theoretical arguments and to date no proper investigation has been conducted to examine the long-term benefits of adopting modern irrigation technology. This study investigates the long-term benefit changes of irrigation induced technological changes using data from Sri Lanka with reference to rice farming. The results show that (1) adopting modern technology on irrigation increases the overall social welfare through consumption of a larger quantity at a lower cost (2) the magnitude, sensitivity and distributional gains depend on the price elasticity of demand and supply as well as the size of the marketable surplus (3) non-farm sector gains are larger than farm sector gains (4) the distribution of the benefits among different types of producers depend on the magnitude of the expansion of the irrigated areas as well as the competition faced by traditional farmers (5) selective technological adoption and subsidies have a detrimental effect on the welfare of other producers who do not enjoy the same benefits (6) the short-term distributional effects are more severe than the long-term effects among different groups of farmers.

A new multilevel converter configuration for high power and high quality applications

The Queensland University of Technology (QUT) allows the presentation of theses for the Degree of Doctor of Philosophy in the format of published or submitted papers, where such papers have been published, accepted or submitted during the period of candidature. This thesis is composed of ten published /submitted papers and book chapters of which nine have been published and one is under review. This project is financially supported by an Australian Research Council (ARC) Discovery Grant with the aim of investigating multilevel topologies for high quality and high power applications, with specific emphasis on renewable energy systems. The rapid evolution of renewable energy within the last several years has resulted in the design of efficient power converters suitable for medium and high-power applications such as wind turbine and photovoltaic (PV) systems. Today, the industrial trend is moving away from heavy and bulky passive components to power converter systems that use more and more semiconductor elements controlled by powerful processor systems. However, it is hard to connect the traditional converters to the high and medium voltage grids, as a single power switch cannot stand at high voltage. For these reasons, a new family of multilevel inverters has appeared as a solution for working with higher voltage levels. Besides this important feature, multilevel converters have the capability to generate stepped waveforms. Consequently, in comparison with conventional two-level inverters, they present lower switching losses, lower voltage stress across loads, lower electromagnetic interference (EMI) and higher quality output waveforms. These properties enable the connection of renewable energy sources directly to the grid without using expensive, bulky, heavy line transformers. Additionally, they minimize the size of the passive filter and increase the durability of electrical devices. However, multilevel converters have only been utilised in very particular applications, mainly due to the structural limitations, high cost and complexity of the multilevel converter system and control. New developments in the fields of power semiconductor switches and processors will favor the multilevel converters for many other fields of application. The main application for the multilevel converter presented in this work is the front-end power converter in renewable energy systems. Diode-clamped and cascade converters are the most common type of multilevel converters widely used in different renewable energy system applications. However, some drawbacks – such as capacitor voltage imbalance, number of components, and complexity of the control system – still exist, and these are investigated in the framework of this thesis. Various simulations using software simulation tools are undertaken and are used to study different cases. The feasibility of the developments is underlined with a series of experimental results. This thesis is divided into two main sections. The first section focuses on solving the capacitor voltage imbalance for a wide range of applications, and on decreasing the complexity of the control strategy on the inverter side. The idea of using sharing switches at the output structure of the DC-DC front-end converters is proposed to balance the series DC link capacitors. A new family of multioutput DC-DC converters is proposed for renewable energy systems connected to the DC link voltage of diode-clamped converters. The main objective of this type of converter is the sharing of the total output voltage into several series voltage levels using sharing switches. This solves the problems associated with capacitor voltage imbalance in diode-clamped multilevel converters. These converters adjust the variable and unregulated DC voltage generated by renewable energy systems (such as PV) to the desirable series multiple voltage levels at the inverter DC side. A multi-output boost (MOB) converter, with one inductor and series output voltage, is presented. This converter is suitable for renewable energy systems based on diode-clamped converters because it boosts the low output voltage and provides the series capacitor at the output side. A simple control strategy using cross voltage control with internal current loop is presented to obtain the desired voltage levels at the output voltage. The proposed topology and control strategy are validated by simulation and hardware results. Using the idea of voltage sharing switches, the circuit structure of different topologies of multi-output DC-DC converters – or multi-output voltage sharing (MOVS) converters – have been proposed. In order to verify the feasibility of this topology and its application, steady state and dynamic analyses have been carried out. Simulation and experiments using the proposed control strategy have verified the mathematical analysis. The second part of this thesis addresses the second problem of multilevel converters: the need to improve their quality with minimum cost and complexity. This is related to utilising asymmetrical multilevel topologies instead of conventional multilevel converters; this can increase the quality of output waveforms with a minimum number of components. It also allows for a reduction in the cost and complexity of systems while maintaining the same output quality, or for an increase in the quality while maintaining the same cost and complexity. Therefore, the asymmetrical configuration for two common types of multilevel converters – diode-clamped and cascade converters – is investigated. Also, as well as addressing the maximisation of the output voltage resolution, some technical issues – such as adjacent switching vectors – should be taken into account in asymmetrical multilevel configurations to keep the total harmonic distortion (THD) and switching losses to a minimum. Thus, the asymmetrical diode-clamped converter is proposed. An appropriate asymmetrical DC link arrangement is presented for four-level diode-clamped converters by keeping adjacent switching vectors. In this way, five-level inverter performance is achieved for the same level of complexity of the four-level inverter. Dealing with the capacitor voltage imbalance problem in asymmetrical diodeclamped converters has inspired the proposal for two different DC-DC topologies with a suitable control strategy. A Triple-Output Boost (TOB) converter and a Boost 3-Output Voltage Sharing (Boost-3OVS) converter connected to the four-level diode-clamped converter are proposed to arrange the proposed asymmetrical DC link for the high modulation indices and unity power factor. Cascade converters have shown their abilities and strengths in medium and high power applications. Using asymmetrical H-bridge inverters, more voltage levels can be generated in output voltage with the same number of components as the symmetrical converters. The concept of cascading multilevel H-bridge cells is used to propose a fifteen-level cascade inverter using a four-level H-bridge symmetrical diode-clamped converter, cascaded with classical two-level Hbridge inverters. A DC voltage ratio of cells is presented to obtain maximum voltage levels on output voltage, with adjacent switching vectors between all possible voltage levels; this can minimize the switching losses. This structure can save five isolated DC sources and twelve switches in comparison to conventional cascade converters with series two-level H bridge inverters. To increase the quality in presented hybrid topology with minimum number of components, a new cascade inverter is verified by cascading an asymmetrical four-level H-bridge diode-clamped inverter. An inverter with nineteen-level performance was achieved. This synthesizes more voltage levels with lower voltage and current THD, rather than using a symmetrical diode-clamped inverter with the same configuration and equivalent number of power components. Two different predictive current control methods for the switching states selection are proposed to minimise either losses or THD of voltage in hybrid converters. High voltage spikes at switching time in experimental results and investigation of a diode-clamped inverter structure raised another problem associated with high-level high voltage multilevel converters. Power switching components with fast switching, combined with hard switched-converters, produce high di/dt during turn off time. Thus, stray inductance of interconnections becomes an important issue and raises overvoltage and EMI issues correlated to the number of components. Planar busbar is a good candidate to reduce interconnection inductance in high power inverters compared with cables. The effect of different transient current loops on busbar physical structure of the high-voltage highlevel diode-clamped converters is highlighted. Design considerations of proper planar busbar are also presented to optimise the overall design of diode-clamped converters.

Communicating with first year students ; so many channels but is anyone listening? A practice report

Communicating with first year students has become a far more complex prospect in the digital age. There is a lot of competition for limited attentional resources from media sources in almost endless channels. Getting important messages to students when there is so much competing information is a difficult prospect for academic and professional divisions of the university alike. Students’ preferences for these communication channels are not well understood and are constantly changing with the introduction of new technology. A first year group was surveyed about their use and preference for various sources of information. Students were generally positive about the use of social networking and other new online media but strongly preferred more established channels for official academic and administrative information. A discussion of the findings and recommendations follows.

Delaying mismatched field multiplications in pairing computations

Miller’s algorithm for computing pairings involves perform- ing multiplications between elements that belong to different finite fields. Namely, elements in the full extension field Fpk are multiplied by elements contained in proper subfields F pk/d , and by elements in the base field Fp . We show that significant speedups in pairing computations can be achieved by delaying these “mismatched” multiplications for an optimal number of iterations. Importantly, we show that our technique can be easily integrated into traditional pairing algorithms; implementers can exploit the computational savings herein by applying only minor changes to existing pairing code.

Re-thinking home economics : from modern to postmodern accounts of pedagogical bodies

Two perceptions of the marginality of home economics are widespread across educational and other contexts. One is that home economics and those who engage in its pedagogy are inevitably marginalised within patriarchal relations in education and culture. This is because home economics is characterised as women's knowledge, for the private domain of the home. The other perception is that only orthodox epistemological frameworks of inquiry should be used to interrogate this state of affairs. These perceptions have prompted leading theorists in the field to call for non-essentialist approaches to research in order to re-think the thinking that has produced this cul-de-sac positioning of home economics as a body of knowledge and a site of teacher practice. This thesis takes up the challenge of working to locate a space outside the frame of modernist research theory and methods, recognising that this shift in epistemology is necessary to unsettle the idea that home economics is inevitably marginalised. The purpose of the study is to reconfigure how we have come to think about home economics teachers and the profession of home economics as a site of cultural practice, in order to think it otherwise (Lather, 1991). This is done by exploring how the culture of home economics is being contested from within. To do so, the thesis uses a 'posthumanist' approach, which rejects the conception of the individual as a unitary and fixed entity, but instead as a subject in process, shaped by desires and language which are not necessarily consciously determined. This posthumanist project focuses attention on pedagogical body subjects as the 'unsaid' of home economics research. It works to transcend the modernist dualism of mind/body, and other binaries central to modernist work, including private/public, male/female,paid/unpaid, and valued/unvalued. In so doing, it refuses the simple margin/centre geometry so characteristic of current perceptions of home economics itself. Three studies make up this work. Studies one and two serve to document the disciplined body of home economics knowledge, the governance of which works towards normalisation of the 'proper' home economics teacher. The analysis of these accounts of home economics teachers by home economics teachers, reveals that home economics teachers are 'skilled' yet they 'suffer' for their profession. Further,home economics knowledge is seen to be complicit in reinforcing the traditional roles of masculinity and femininity, thereby reinforcing heterosexual normativity which is central to patriarchal society. The third study looks to four 'atypical'subjects who defy the category of 'proper' and 'normal' home economics teacher. These 'atypical' bodies are 'skilled' but fiercely reject the label of 'suffering'. The discussion of the studies is a feminist poststructural account, using Russo's (1994) notion of the grotesque body, which is emergent from Bakhtin's (1968) theory of the carnivalesque. It draws on the 'shreds' of home economics pedagogy,scrutinising them for their subversive, transformative potential. In this analysis, the giving and taking of pleasure and fun in the home economics classroom presents moments of surprise and of carnival. Foucault's notion of the construction of the ethical individual shows these 'atypical' bodies to be 'immoderate' yet striving hard to be 'continent' body subjects. This research captures moments of transgression which suggest that transformative moments are already embodied in the pedagogical practices of home economics teachers, and these can be 'seen' when re-looking through postmodemist lenses. Hence, the cultural practices ofhome economics as inevitably marginalised are being contested from within. Until now, home economics as a lived culture has failed to recognise possibilities for reconstructing its own field beyond the confines of modernity. This research is an example of how to think about home economics teachers and the profession as a reconfigured cultural practice. Future research about home economics as a body of knowledge and a site of teacher practice need not retell a simple story of oppression. Using postmodemist epistemologies is one way to provide opportunities for new ways of looking.

A secure framework and related protocols for ubiquitous access to electronic health records using Java sim cards

Ubiquitous access to patient medical records is an important aspect of caring for patient safety. Unavailability of sufficient medical information at the point-ofcare could possibly lead to a fatality. The U.S. Institute of Medicine has reported that between 44,000 and 98,000 people die each year due to medical errors, such as incorrect medication dosages, due to poor legibility in manual records, or delays in consolidating needed information to discern the proper intervention. In this research we propose employing emergent technologies such as Java SIM Cards (JSC), Smart Phones (SP), Next Generation Networks (NGN), Near Field Communications (NFC), Public Key Infrastructure (PKI), and Biometric Identification to develop a secure framework and related protocols for ubiquitous access to Electronic Health Records (EHR). A partial EHR contained within a JSC can be used at the point-of-care in order to help quick diagnosis of a patient’s problems. The full EHR can be accessed from an Electronic Health Records Centre (EHRC) when time and network availability permit. Moreover, this framework and related protocols enable patients to give their explicit consent to a doctor to access their personal medical data, by using their Smart Phone, when the doctor needs to see or update the patient’s medical information during an examination. Also our proposed solution would give the power to patients to modify the Access Control List (ACL) related to their EHRs and view their EHRs through their Smart Phone. Currently, very limited research has been done on using JSCs and similar technologies as a portable repository of EHRs or on the specific security issues that are likely to arise when JSCs are used with ubiquitous access to EHRs. Previous research is concerned with using Medicare cards, a kind of Smart Card, as a repository of medical information at the patient point-of-care. However, this imposes some limitations on the patient’s emergency medical care, including the inability to detect the patient’s location, to call and send information to an emergency room automatically, and to interact with the patient in order to get consent. The aim of our framework and related protocols is to overcome these limitations by taking advantage of the SIM card and the technologies mentioned above. Briefly, our framework and related protocols will offer the full benefits of accessing an up-to-date, precise, and comprehensive medical history of a patient, whilst its mobility will provide ubiquitous access to medical and patient information everywhere it is needed. The objective of our framework and related protocols is to automate interactions between patients, healthcare providers and insurance organisations, increase patient safety, improve quality of care, and reduce the costs.

A spectroscopic comparison of selected Chinese kaolinite, coal bearing kaolinite and halloysite : a mid-infrared and near-infrared study

Mid-infrared (MIR) and near-infrared (NIR) spectroscopy have been compared and evaluated for differentiating kaolinite, coal bearing kaolinite and halloysite. Kaolinite, coal bearing kaolinite and halloysite are the three relative abundant mineral of the kaolin group, especially in China. In the MIR spectra, the differences are shown in the 3000-3600 cm-1 between kaolinite and halloysite. It can not be obviously differentiated the kaolinite and halloysite, let alone kaolinite and coal bearing kaolinite. However, NIR, together with MIR, give us the sufficient evidence to differentiate the kaolinite and halloysite, especially kaolinite and coal bearing kaolinite. There are obvious differences between kaolinite and halloysite in the all range of their spectra, and it also show some difference between kaolinite and coal bearing kaolinite. Therefore, the reproducibility of measurement, signal to noise ratio and richness of qualitative information should be simultaneously considered for proper selection of a spectroscopic method for mineral analysis.