The Dynamics of High-Speed Railway Bridges: A Review of Design Issues and New Research for Lateral Dynamics

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for the consideration of safe running conditions for the trains. In this work we start by reviewing the relevance of some basic design aspects. The significance of impact factor envelopes for moving loads is considered first. Resonance which may be achieved for high-speed trains requires dynamic analysis, for which some key aspects are discussed. The relevance of performing a longitudinal distribution of axle loads, the number of modes taken in analysis, and the consideration of vehicle-structure interaction are discussed with representative examples. The lateral dynamic effects of running trains on bridges is of importance for laterally compliant viaducts, such as some very tall structures erected in new high-speed lines. The relevance of this study is mainly for the safety of the traffic, considering both internal actions such as the hunting motion as well as external actions such as wind or earthquakes [1]. These studies require three-dimensional dynamic coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework [2]. The wheel-rail contact has been considered using a FastSim algorithm which provides a compromise between accuracy and computational cost, and captures the main nonlinear response of the contact interface. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the dynamic interaction between bridge and vehicle. The second application is to a real HS viaduct with a long continuous deck and tall piers and high lateral compliance [3]. The results show the safety of the traffic as well as the importance of considering features such as track alignment irregularities.

Direct estimation wave setup as a medium level in swash

The extreme runup is a key parameter for a shore risk analysis in which the accurate and quantitative estimation of the upper limit reached by waves is essential. Runup can be better approximated by splitting the setup and swash semi-amplitude contributions. In an experimental study recording setup becomes difficult due to infragravity motions within the surf zone, hence, it would be desirable to measure the setup with available methodologies and devices. In this research, an analysis is made of evaluated the convenience of direct estimation setup as the medium level in the swash zone for experimental runup analysis through a physical model. A physical mobile bed model was setup in a wave flume at the Laboratory for Maritime Experimentation of CEDEX. The wave flume is 36 metres long, 6.5 metres wide and 1.3 metres high. The physical model was designed to cover a reasonable range of parameters, three different slopes (1/50, 1/30 and 1/20), two sand grain sizes (D50 = 0.12 mm and 0.70 mm) and a range for the Iribarren number in deep water (ξ0) from 0.1 to 0.6. Best formulations were chosen for estimating a theoretical setup in the physical model application. Once theoretical setup had been obtained, a comparison was made with an estimation of the setup directly as a medium level of the oscillation in swash usually considered in extreme runup analyses. A good correlation was noted between both theoretical and time-averaging setup and a relation is proposed. Extreme runup is analysed through the sum of setup and semi-amplitude of swash. An equation is proposed that could be applied in strong foreshore slope-dependent reflective beaches.

Nonlinear models for lateral dynamics of railway vehicles on bridges subject to wind action

The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require threedimensional coupled vehicle-bridge models, wheree consideration of wheel to rail contact is a key aspect. Furthermore, an adequate evaluation of safety of rail traffic requires nonlinear models. A nonlinear coupled model is proposed here for vehicle-structure vertical and lateral dynamics. Vehicles are considered as fully three-dimensional multibody systems including gyroscopic terms and large rotation effects. The bridge structure is modeled by means of finite elements which may be of beam, shell or continuum type and may include geometric or material nonlinearities. The track geometry includes distributed track alignment irregularities. Both subsystems (bridge and vehicles) are described with coordinates in absolute reference frames, as opposed to alternative approaches which describe the multibody system with coordinates relative to the base bridge motion. The wheelrail contact employed is a semi-Hertzian model based on realistic wheel-rail profiles. It allows a detailed geometrical description of the contact patch under each wheel including multiple-point contact, flange contact and uplift. Normal and tangential stresses in each contact are integrated at each time-step to obtain the resultant contact forces. The models have been implemented within an existing finite element analysis software with multibody capabilities, Abaqus (Simulia Ltd., 2010). Further details of the model are presented in Antolín et al. (2012). Representative applications are presented for railway vehicles under lateral wind action on laterally compliant viaducts, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle.

Analysis of the static and dynamic behaviour of hydraulic fills

En la actualidad existe un gran conocimiento en la caracterización de rellenos hidráulicos, tanto en su caracterización estática, como dinámica. Sin embargo, son escasos en la literatura estudios más generales y globales de estos materiales, muy relacionados con sus usos y principales problemáticas en obras portuarias y mineras. Los procedimientos semi‐empíricos para la evaluación del efecto silo en las celdas de cajones portuarios, así como para el potencial de licuefacción de estos suelos durantes cargas instantáneas y terremotos, se basan en estudios donde la influencia de los parámetros que los rigen no se conocen en gran medida, dando lugar a resultados con considerable dispersión. Este es el caso, por ejemplo, de los daños notificados por el grupo de investigación del Puerto de Barcelona, la rotura de los cajones portuarios en el Puerto de Barcelona en 2007. Por estos motivos y otros, se ha decidido desarrollar un análisis para la evaluación de estos problemas mediante la propuesta de una metodología teórico‐numérica y empírica. El enfoque teórico‐numérico desarrollado en el presente estudio se centra en la determinación del marco teórico y las herramientas numéricas capaces de solventar los retos que presentan estos problemas. La complejidad del problema procede de varios aspectos fundamentales: el comportamiento no lineal de los suelos poco confinados o flojos en procesos de consolidación por preso propio; su alto potencial de licuefacción; la caracterización hidromecánica de los contactos entre estructuras y suelo (camino preferencial para el flujo de agua y consolidación lateral); el punto de partida de los problemas con un estado de tensiones efectivas prácticamente nulo. En cuanto al enfoque experimental, se ha propuesto una metodología de laboratorio muy sencilla para la caracterización hidromecánica del suelo y las interfaces, sin la necesidad de usar complejos aparatos de laboratorio o procedimientos excesivamente complicados. Este trabajo incluye por tanto un breve repaso a los aspectos relacionados con la ejecución de los rellenos hidráulicos, sus usos principales y los fenómenos relacionados, con el fin de establecer un punto de partida para el presente estudio. Este repaso abarca desde la evolución de las ecuaciones de consolidación tradicionales (Terzaghi, 1943), (Gibson, English & Hussey, 1967) y las metodologías de cálculo (Townsend & McVay, 1990) (Fredlund, Donaldson and Gitirana, 2009) hasta las contribuciones en relación al efecto silo (Ranssen, 1985) (Ravenet, 1977) y sobre el fenómeno de la licuefacción (Casagrande, 1936) (Castro, 1969) (Been & Jefferies, 1985) (Pastor & Zienkiewicz, 1986). Con motivo de este estudio se ha desarrollado exclusivamente un código basado en el método de los elementos finitos (MEF) empleando el programa MATLAB. Para ello, se ha esablecido un marco teórico (Biot, 1941) (Zienkiewicz & Shiomi, 1984) (Segura & Caron, 2004) y numérico (Zienkiewicz & Taylor, 1989) (Huerta & Rodríguez, 1992) (Segura & Carol, 2008) para resolver problemas de consolidación multidimensional con condiciones de contorno friccionales, y los correspondientes modelos constitutivos (Pastor & Zienkiewicz, 1986) (Fiu & Liu, 2011). Asimismo, se ha desarrollado una metodología experimental a través de una serie de ensayos de laboratorio para la calibración de los modelos constitutivos y de la caracterización de parámetros índice y de flujo (Castro, 1969) (Bahda 1997) (Been & Jefferies, 2006). Para ello se han empleado arenas de Hostun como material (relleno hidráulico) de referencia. Como principal aportación se incluyen una serie de nuevos ensayos de corte directo para la caracterización hidromecánica de la interfaz suelo – estructura de hormigón, para diferentes tipos de encofrados y rugosidades. Finalmente, se han diseñado una serie de algoritmos específicos para la resolución del set de ecuaciones diferenciales de gobierno que definen este problema. Estos algoritmos son de gran importancia en este problema para tratar el procesamiento transitorio de la consolidación de los rellenos hidráulicos, y de otros efectos relacionados con su implementación en celdas de cajones, como el efecto silo y la licuefacciones autoinducida. Para ello, se ha establecido un modelo 2D axisimétrico, con formulación acoplada u‐p para elementos continuos y elementos interfaz (de espesor cero), que tratan de simular las condiciones de estos rellenos hidráulicos cuando se colocan en las celdas portuarias. Este caso de estudio hace referencia clara a materiales granulares en estado inicial muy suelto y con escasas tensiones efectivas, es decir, con prácticamente todas las sobrepresiones ocasionadas por el proceso de autoconsolidación (por peso propio). Por todo ello se requiere de algoritmos numéricos específicos, así como de modelos constitutivos particulares, para los elementos del continuo y para los elementos interfaz. En el caso de la simulación de diferentes procedimientos de puesta en obra de los rellenos se ha requerido la modificacion de los algoritmos empleados para poder así representar numéricamente la puesta en obra de estos materiales, además de poder realizar una comparativa de los resultados para los distintos procedimientos. La constante actualización de los parámetros del suelo, hace también de este algoritmo una potente herramienta que permite establecer un interesante juego de perfiles de variables, tales como la densidad, el índice de huecos, la fracción de sólidos, el exceso de presiones, y tensiones y deformaciones. En definitiva, el modelo otorga un mejor entendimiento del efecto silo, término comúnmente usado para definir el fenómeno transitorio del gradiente de presiones laterales en las estructuras de contención en forma de silo. Finalmente se incluyen una serie de comparativas entre los resultados del modelo y de diferentes estudios de la literatura técnica, tanto para el fenómeno de las consolidaciones por preso propio (Fredlund, Donaldson & Gitirana, 2009) como para el estudio del efecto silo (Puertos del Estado, 2006, EuroCódigo (2006), Japan Tech, Stands. (2009), etc.). Para concluir, se propone el diseño de un prototipo de columna de decantación con paredes friccionales, como principal propuesta de futura línea de investigación. Wide research is nowadays available on the characterization of hydraulic fills in terms of either static or dynamic behavior. However, reported comprehensive analyses of these soils when meant for port or mining works are scarce. Moreover, the semi‐empirical procedures for assessing the silo effect on cells in floating caissons, and the liquefaction potential of these soils during sudden loads or earthquakes are based on studies where the underlying influence parameters are not well known, yielding results with significant scatter. This is the case, for instance, of hazards reported by the Barcelona Liquefaction working group, with the failure of harbor walls in 2007. By virtue of this, a complex approach has been undertaken to evaluate the problem by a proposal of numerical and laboratory methodology. Within a theoretical and numerical scope, the study is focused on the numerical tools capable to face the different challenges of this problem. The complexity is manifold; the highly non‐linear behavior of consolidating soft soils; their potentially liquefactable nature, the significance of the hydromechanics of the soil‐structure contact, the discontinuities as preferential paths for water flow, setting “negligible” effective stresses as initial conditions. Within an experimental scope, a straightforward laboratory methodology is introduced for the hydromechanical characterization of the soil and the interface without the need of complex laboratory devices or cumbersome procedures. Therefore, this study includes a brief overview of the hydraulic filling execution, main uses (land reclamation, filled cells, tailing dams, etc.) and the underlying phenomena (self‐weight consolidation, silo effect, liquefaction, etc.). It comprises from the evolution of the traditional consolidation equations (Terzaghi, 1943), (Gibson, English, & Hussey, 1967) and solving methodologies (Townsend & McVay, 1990) (Fredlund, Donaldson and Gitirana, 2009) to the contributions in terms of silo effect (Ranssen, 1895) (Ravenet, 1977) and liquefaction phenomena (Casagrande, 1936) (Castro, 1969) (Been & Jefferies, 1985) (Pastor & Zienkiewicz, 1986). The novelty of the study lies on the development of a Finite Element Method (FEM) code, exclusively formulated for this problem. Subsequently, a theoretical (Biot, 1941) (Zienkiewicz and Shiomi, 1984) (Segura and Carol, 2004) and numerical approach (Zienkiewicz and Taylor, 1989) (Huerta, A. & Rodriguez, A., 1992) (Segura, J.M. & Carol, I., 2008) is introduced for multidimensional consolidation problems with frictional contacts and the corresponding constitutive models (Pastor & Zienkiewicz, 1986) (Fu & Liu, 2011). An experimental methodology is presented for the laboratory test and material characterization (Castro 1969) (Bahda 1997) (Been & Jefferies 2006) using Hostun sands as reference hydraulic fill. A series of singular interaction shear tests for the interface calibration is included. Finally, a specific model algorithm for the solution of the set of differential equations governing the problem is presented. The process of consolidation and settlements involves a comprehensive simulation of the transient process of decantation and the build‐up of the silo effect in cells and certain phenomena related to self‐compaction and liquefaction. For this, an implementation of a 2D axi‐syimmetric coupled model with continuum and interface elements, aimed at simulating conditions and self‐weight consolidation of hydraulic fills once placed into floating caisson cells or close to retaining structures. This basically concerns a loose granular soil with a negligible initial effective stress level at the onset of the process. The implementation requires a specific numerical algorithm as well as specific constitutive models for both the continuum and the interface elements. The simulation of implementation procedures for the fills has required the modification of the algorithm so that a numerical representation of these procedures is carried out. A comparison of the results for the different procedures is interesting for the global analysis. Furthermore, the continuous updating of the model provides an insightful logging of variable profiles such as density, void ratio and solid fraction profiles, total and excess pore pressure, stresses and strains. This will lead to a better understanding of complex phenomena such as the transient gradient in lateral pressures due to silo effect in saturated soils. Interesting model and literature comparisons for the self‐weight consolidation (Fredlund, Donaldson, & Gitirana, 2009) and the silo effect results (Puertos del Estado (2006), EuroCode (2006), Japan Tech, Stands. (2009)). This study closes with the design of a decantation column prototype with frictional walls as the main future line of research.

Tecnología y equipos para redes ultrarrápidas

Este proyecto de fin de carrera se realiza bajo la supervisión y aprobación de la empresa BT S.A.U. Este documento pretende ser un manual básico para dar a conocer al lector los elementos, herramientas y procedimientos para llevar a cabo un proyecto de tendido de fibra óptica en España. Se compone de 5 temas cuyos contenidos paso a resumir a continuación. Tema 1. En él, se muestra una explicación a las redes de acceso y las distintas topologías FTTx necesarias para llegar al cliente, además de las tecnologías y elementos utilizados para su conexión. Tema 2. Se explicará la regulación española para el tendido de redes de acceso necesarios como son la Regulación OBA, coubicación en las centrales de Telefónica, y la Regulación MARCO, compartición de la infraestructura de Telefónica con otros operadores. Tema 3. Aquí se explica la herramienta NEON, necesaria para la “comunicación” con Telefónica para las peticiones de la compartición de su infraestructura y un apartado para la legislación municipal para el despliegue de redes de fibra. Tema 4. Expondremos el procedimiento de trabajo en campo. Hablaremos de los procedimientos del tendido de cable, las obras civiles, y finalmente las medidas para comprobar el enlace. Tema 5. Explicaremos un ejemplo de despliegue real, desde la viabilidad hasta finalmente el tendido. Tema 6. Por último, expondré mis conclusiones y trabajos futuros. Este proyecto está orientado desde un punto de vista de la infraestructura (Capa Física, Modelo OSI). ABSTRACT. This thesis project is carried out under the supervision and approval of the company BT S.A.U. This document is intended as a basic manual to expose the reader items, tools, and procedures to carry out a deployment of optical fiber project in Spain. It is composed of 5 topics whose contents I summarize below. Topic 1. In it, shows an explanation to access networks and different topologies FTTx necessary to reach the customer, as well as technologies and elements used for connection. Topic 2. In this topic will be explained the Spanish regulation for the access networks needed such as the regulation of OBA, co-location in Telefonica’s central, and the framework regulation, sharing of Telefonica infrastructure with other operators. Topic 3. Here we explain the tool NEON, necessary for the "communication" with Telefónica for requests for infrastructure sharing, and a section for municipal legislation for the deployment of fiber networks. Topic 4. We will exhibit work in field procedure. We will discuss the procedures of laying cable, civil works, and finally measures to check the link. Topic 5. We will present an example of an actual deployment, from viability until finally laying. Topic 6. Finally, I shall explain my conclusions and future work. This project is from a point of view of the infrastructure (physical layer, OSI model).

Nueva tecnología para la separación de gases atmosféricos y captura de dióxido de carbono por aplicación de campos electromagnéticos y fotoionización

Son numerosos los expertos que predicen que hasta pasado 2050 no se utilizarán masivamente las energías de origen renovable, y que por tanto se mantendrá la emisión de dióxido de carbono de forma incontrolada. Entre tanto, y previendo que este tipo de uso se mantenga hasta un horizonte temporal aún más lejano, la captura, concentración y secuestro o reutilización de dióxido de carbono es y será una de las principales soluciones a implantar para paliar el problema medioambiental causado. Sin embargo, las tecnologías existentes y en desarrollo de captura y concentración de este tipo de gas, presentan dos limitaciones: las grandes cantidades de energía que consumen y los grandes volúmenes de sustancias potencialmente dañinas para el medioambiente que producen durante su funcionamiento. Ambas razones hacen que no sean atractivas para su implantación y uso de forma extensiva. La solución planteada en la presente tesis doctoral se caracteriza por la ausencia de residuos producidos en la operación de captura y concentración del dióxido de carbono, por no utilizar substancias químicas y físicas habituales en las técnicas actuales, por disminuir los consumos energéticos al carecer de sistemas móviles y por evitar la regeneración química y física de los materiales utilizados en la actualidad. Así mismo, plantea grandes retos a futuras innovaciones sobre la idea propuesta que busquen fundamentalmente la disminución de la energía utilizada durante su funcionamiento y la optimización de sus componentes principales. Para conseguir el objetivo antes citado, la presente tesis doctoral, una vez establecido el planteamiento del problema al que se busca solución (capítulo 1), del estudio de las técnicas de separación de gases atmosféricos utilizadas en la actualidad, así como del de los sistemas fundamentales de las instalaciones de captura y concentración del dióxido de carbono (capítulo 2) y tras una definición del marco conceptual y teórico (capítulo 3), aborda el diseño de un prototipo de ionización fotónica de los gases atmosféricos para su posterior separación electrostática, a partir del estudio, adaptación y mejora del funcionamiento de los sistemas de espectrometría de masas. Se diseñarán y desarrollarán los sistemas básicos de fotoionización, mediante el uso de fuentes de fotones coherentes, y los de separación electrostática (capítulo 4), en que se basa el funcionamiento de este sistema de separación de gases atmosféricos y de captura y concentración de dióxido de carbono para construir un prototipo a nivel laboratorio. Posteriormente, en el capítulo 5, serán probados utilizando una matriz experimental que cubra los rangos de funcionamiento previstos y aporte suficientes datos experimentales para corregir y desarrollar el marco teórico real, y con los que se pueda establecer y corregir un modelo físico– matemático de simulación (capítulo 6) aplicable a la unidad en su conjunto. Finalmente, debido a la utilización de unidades de ionización fotónica, sistemas láseres intensos y sistemas eléctricos de gran potencia, es preciso analizar el riesgo biológico a las personas y al medioambiente debido al impacto de la radiación electromagnética producida (capítulo 7), minimizando su impacto y cumpliendo con la legislación vigente. En el capítulo 8 se planteará un diseño escalable a tamaño piloto de la nueva tecnología propuesta y sus principales modos de funcionamiento, así como un análisis de viabilidad económica. Como consecuencia de la tesis doctoral propuesta y del desarrollo de la unidad de separación atmosférica y de captura y concentración de dióxido de carbono, surgen diversas posibilidades de estudio que pueden ser objeto de nuevas tesis doctorales y de futuros desarrollos de ingeniería. El capítulo 9 tratará de incidir en estos aspectos indicando líneas de investigación para futuras tesis y desarrollos industriales. ABSTRACT A large number of experts predict that until at least 2050 renewable energy sources will not be massively used, and for that reason, current Primary Energy sources based on extensive use of fossil fuel will be used maintaining out of control emissions, Carbon Dioxide above all. Meanwhile, under this scenario and considering its extension until at least 2050, Carbon Capture, Concentration, Storage and/or Reuse is and will be one of the main solutions to minimise Greenhouse Gasses environmental effect. But, current Carbon Capture and Storage technology state of development has two main problems: it is a too large energy consuming technology and during normal use it produces a large volume of environmentally dangerous substances. Both reasons are limiting its development and its extensive use. This Ph Degree Thesis document proposes a solution to get the expected effect using a new atmospheric gasses separation system with the following characteristics: absence of wastes produced, it needs no chemical and/or physical substances during its operation, it reduces to minimum the internal energy consumptions due to absence of mobile equipment and it does not need any chemical and/or physical regeneration of substances. This system is beyond the State of the Art of current technology development. Additionally, the proposed solution raises huge challenges for future innovations of the proposed idea finding radical reduction of internal energy consumption during functioning, as well as regarding optimisation of main components, systems and modes of operation. To achieve this target, once established the main problem, main challenge and potential solving solutions (Chapter 1), it is established an initial starting point fixing the Atmospheric Gasses Separation and Carbon Capture and Storage developments (Chapter 2), as well as it will be defined the theoretical and basic model, including existing and potential new governing laws and mathematical formulas to control its system functioning (Chapter 3), this document will deal with the design of an installation of an operating system based on photonic ionization of atmospheric gasses to be separated in a later separation system based on the application of electrostatic fields. It will be developed a basic atmospheric gasses ionization prototype based on intense radioactive sources capable to ionize gasses by coherent photonic radiation, and a basic design of electrostatic separation system (Chapter 4). Both basic designs are the core of the proposed technology that separates Atmospheric Gasses and captures and concentrates Carbon Dioxide. Chapter 5 will includes experimental results obtained from an experimental testing matrix covering expected prototype functioning regimes. With the obtained experimental data, theoretical model will be corrected and improved to act as the real physical and mathematical model capable to simulate real system function (Chapter 6). Finally, it is necessary to assess potential biological risk to public and environment due to the proposed use of units of intense energy photonic ionization, by laser beams or by non–coherent sources and large electromagnetic systems with high energy consumption. It is necessary to know the impact in terms of and electromagnetic radiation taking into account National Legislation (Chapter 7). On Chapter 8, an up scaled pilot plant will be established covering main functioning modes and an economic feasibility assessment. As a consequence of this PhD Thesis, a new field of potential researches and new PhD Thesis are opened, as well as future engineering and industrial developments (Chapter 9).

Some aspects of lubrication in heavy regimes: thermal effects, stability and turbulence

In this work, a combination of numerical methods applied to thermohydrodynamic lubrication problems with cavitation is presented. It should be emphasized the difficulty of the nonlinear mathematical coupled model involving a free boundary problem, but also the simplicity of the algorithms employed to solve it. So, finite element discretizations for the hydrodynamic and thermal equations combined with upwind techniques for the convection terms and duality methods for nonlinear features are proposed. Additionally, a model describing the movement of the shaft is provided. Considering the shaft as a rigid body this model will consist of an ODE system relating acceleration of the center of gravity and external and pressure loads. The numerical experiments of mechanical stability try to clarify the position of the neutral stability curve. Finally, a rotating machine for ship propulsion involving both axial and radial bearings operating with nonconventional lubricants (seawater to avoid environmental pollution) is analyzed by using laminar and turbulent inertial flows.

Análisis comparativo y nuevas estimaciones de las tasas de rebase en obras marítimas en grandes profundidades

El rebase se define como el transporte de una cantidad importante de agua sobre la coronación de una estructura. Por tanto, es el fenómeno que, en general, determina la cota de coronación del dique dependiendo de la cantidad aceptable del mismo, a la vista de condicionantes funcionales y estructurales del dique. En general, la cantidad de rebase que puede tolerar un dique de abrigo desde el punto de vista de su integridad estructural es muy superior a la cantidad permisible desde el punto de vista de su funcionalidad. Por otro lado, el diseño de un dique con una probabilidad de rebase demasiado baja o nula conduciría a diseños incompatibles con consideraciones de otro tipo, como son las estéticas o las económicas. Existen distintas formas de estudiar el rebase producido por el oleaje sobre los espaldones de las obras marítimas. Las más habituales son los ensayos en modelo físico y las formulaciones empíricas o semi-empíricas. Las menos habituales son la instrumentación en prototipo, las redes neuronales y los modelos numéricos. Los ensayos en modelo físico son la herramienta más precisa y fiable para el estudio específico de cada caso, debido a la complejidad del proceso de rebase, con multitud de fenómenos físicos y parámetros involucrados. Los modelos físicos permiten conocer el comportamiento hidráulico y estructural del dique, identificando posibles fallos en el proyecto antes de su ejecución, evaluando diversas alternativas y todo esto con el consiguiente ahorro en costes de construcción mediante la aportación de mejoras al diseño inicial de la estructura. Sin embargo, presentan algunos inconvenientes derivados de los márgenes de error asociados a los ”efectos de escala y de modelo”. Las formulaciones empíricas o semi-empíricas presentan el inconveniente de que su uso está limitado por la aplicabilidad de las fórmulas, ya que éstas sólo son válidas para una casuística de condiciones ambientales y tipologías estructurales limitadas al rango de lo reproducido en los ensayos. El objetivo de la presente Tesis Doctoral es el contrate de las formulaciones desarrolladas por diferentes autores en materia de rebase en distintas tipologías de diques de abrigo. Para ello, se ha realizado en primer lugar la recopilación y el análisis de las formulaciones existentes para estimar la tasa de rebase sobre diques en talud y verticales. Posteriormente, se llevó a cabo el contraste de dichas formulaciones con los resultados obtenidos en una serie de ensayos realizados en el Centro de Estudios de Puertos y Costas. Para finalizar, se aplicó a los ensayos de diques en talud seleccionados la herramienta neuronal NN-OVERTOPPING2, desarrollada en el proyecto europeo de rebases CLASH (“Crest Level Assessment of Coastal Structures by Full Scale Monitoring, Neural Network Prediction and Hazard Analysis on Permissible Wave Overtopping”), contrastando de este modo la tasa de rebase obtenida en los ensayos con este otro método basado en la teoría de las redes neuronales. Posteriormente, se analizó la influencia del viento en el rebase. Para ello se han realizado una serie de ensayos en modelo físico a escala reducida, generando oleaje con y sin viento, sobre la sección vertical del Dique de Levante de Málaga. Finalmente, se presenta el análisis crítico del contraste de cada una de las formulaciones aplicadas a los ensayos seleccionados, que conduce a las conclusiones obtenidas en la presente Tesis Doctoral. Overtopping is defined as the volume of water surpassing the crest of a breakwater and reaching the sheltered area. This phenomenon determines the breakwater’s crest level, depending on the volume of water admissible at the rear because of the sheltered area’s functional and structural conditioning factors. The ways to assess overtopping processes range from those deemed to be most traditional, such as semi-empirical or empirical type equations and physical, reduced scale model tests, to others less usual such as the instrumentation of actual breakwaters (prototypes), artificial neural networks and numerical models. Determining overtopping in reduced scale physical model tests is simple but the values obtained are affected to a greater or lesser degree by the effects of a scale model-prototype such that it can only be considered as an approximation to what actually happens. Nevertheless, physical models are considered to be highly useful for estimating damage that may occur in the area sheltered by the breakwater. Therefore, although physical models present certain problems fundamentally deriving from scale effects, they are still the most accurate, reliable tool for the specific study of each case, especially when large sized models are adopted and wind is generated Empirical expressions obtained from laboratory tests have been developed for calculating the overtopping rate and, therefore, the formulas obtained obviously depend not only on environmental conditions – wave height, wave period and water level – but also on the model’s characteristics and are only applicable in a range of validity of the tests performed in each case. The purpose of this Thesis is to make a comparative analysis of methods for calculating overtopping rates developed by different authors for harbour breakwater overtopping. First, existing equations were compiled and analysed in order to estimate the overtopping rate on sloping and vertical breakwaters. These equations were then compared with the results obtained in a number of tests performed in the Centre for Port and Coastal Studies of the CEDEX. In addition, a neural network model developed in the European CLASH Project (“Crest Level Assessment of Coastal Structures by Full Scale Monitoring, Neural Network Prediction and Hazard Analysis on Permissible Wave Overtopping“) was also tested. Finally, the wind effects on overtopping are evaluated using tests performed with and without wind in the physical model of the Levante Breakwater (Málaga).

Synechocystis HSP17 is an amphitropic protein that stabilizes heat-stressed membranes and binds denatured proteins for subsequent chaperone-mediated refolding

The small heat shock proteins (sHSPs) are ubiquitous stress proteins proposed to act as molecular chaperones to prevent irreversible protein denaturation. We characterized the chaperone activity of Synechocystis HSP17 and found that it has not only protein-protective activity, but also a previously unrecognized ability to stabilize lipid membranes. Like other sHSPs, recombinant Synechocystis HSP17 formed stable complexes with denatured malate dehydrogenase and served as a reservoir for the unfolded substrate, transferring it to the DnaK/DnaJ/GrpE and GroEL/ES chaperone network for subsequent refolding. Large unilamellar vesicles made of synthetic and cyanobacterial lipids were found to modulate this refolding process. Investigation of HSP17-lipid interactions revealed a preference for the liquid crystalline phase and resulted in an elevated physical order in model lipid membranes. Direct evidence for the participation of HSP17 in the control of thylakoid membrane physical state in vivo was gained by examining an hsp17− deletion mutant compared with the isogenic wild-type hsp17+ revertant Synechocystis cells. We suggest that, together with GroEL, HSP17 behaves as an amphitropic protein and plays a dual role. Depending on its membrane or cytosolic location, it may function as a “membrane stabilizing factor” as well as a member of a multichaperone protein-folding network. Membrane association of sHSPs could antagonize the heat-induced hyperfluidization of specific membrane domains and thereby serve to preserve structural and functional integrity of biomembranes.

Incorporação do espalhamento Compton no modelo de TBC modificado

No último século, houve grande avanço no entendimento das interações das radiações com a matéria. Essa compreensão se faz necessária para diversas aplicações, entre elas o uso de raios X no diagnóstico por imagens. Neste caso, imagens são formadas pelo contraste resultante da diferença na atenuação dos raios X pelos diferentes tecidos do corpo. Entretanto, algumas das interações dos raios X com a matéria podem levar à redução da qualidade destas imagens, como é o caso dos fenômenos de espalhamento. Muitas abordagens foram propostas para estimar a distribuição espectral de fótons espalhados por uma barreira, ou seja, como no caso de um feixe de campo largo, ao atingir um plano detector, tais como modelos que utilizam métodos de Monte Carlo e modelos que utilizam aproximações analíticas. Supondo-se um espectro de um feixe primário que não interage com nenhum objeto após sua emissão pelo tubo de raios X, este espectro é, essencialmente representado pelos modelos propostos anteriormente. Contudo, considerando-se um feixe largo de radiação X, interagindo com um objeto, a radiação a ser detectada por um espectrômetro, passa a ser composta pelo feixe primário, atenuado pelo material adicionado, e uma fração de radiação espalhada. A soma destas duas contribuições passa a compor o feixe resultante. Esta soma do feixe primário atenuado, com o feixe de radiação espalhada, é o que se mede em um detector real na condição de feixe largo. O modelo proposto neste trabalho visa calcular o espectro de um tubo de raios X, em situação de feixe largo, o mais fidedigno possível ao que se medem em condições reais. Neste trabalho se propõe a discretização do volume de interação em pequenos elementos de volume, nos quais se calcula o espalhamento Compton, fazendo uso de um espectro de fótons gerado pelo Modelo de TBC, a equação de Klein-Nishina e considerações geométricas. Por fim, o espectro de fótons espalhados em cada elemento de volume é somado ao espalhamento dos demais elementos de volume, resultando no espectro total espalhado. O modelo proposto foi implementado em ambiente computacional MATLAB® e comparado com medições experimentais para sua validação. O modelo proposto foi capaz de produzir espectros espalhados em diferentes condições, apresentando boa conformidade com os valores medidos, tanto em termos quantitativos, nas quais a diferença entre kerma no ar calculado e kerma no ar medido é menor que 10%, quanto qualitativos, com fatores de mérito superiores a 90%.

Surface wind-stress threshold for glacial Atlantic overturning

Using a coupled model of intermediate complexity the sensitivity of the last glacial maximum (LGM) Atlantic meridional overturning circulation (AMOC) to the strength of surface wind-stress is investigated. A threshold is found below which North Atlantic deep water formation (DWF) takes place south of Greenland and the AMOC is relatively weak. Above this threshold, DWF occurs north of the Greenland-Scotland ridge, leading to a vigorous AMOC. This nonlinear behavior is explained through enhanced salt transport by the wind-driven gyre circulation and the overturning itself. Both pattern and magnitude of the Nordic Sea's temperature difference between strong and weak AMOC states are consistent with those reconstructed for abrupt climate changes of the last glacial period. Our results thus point to a potentially relevant role of surface winds in these phenomena.

Investigating the causes of the response of the thermohaline circulation to past and future climate changes

The Atlantic thermohaline circulation (THC) is an important part of the earth's climate system. Previous research has shown large uncertainties in simulating future changes in this critical system. The simulated THC response to idealized freshwater perturbations and the associated climate changes have been intercompared as an activity of World Climate Research Program (WCRP) Coupled Model Intercomparison Project/Paleo-Modeling Intercomparison Project (CMIP/PMIP) committees. This intercomparison among models ranging from the earth system models of intermediate complexity (EMICs) to the fully coupled atmosphere-ocean general circulation models (AOGCMs) seeks to document and improve understanding of the causes of the wide variations in the modeled THC response. The robustness of particular simulation features has been evaluated across the model results. In response to 0.1-Sv (1 Sv equivalent to 10^6 ms^3 s^-1) freshwater input in the northern North Atlantic, the multimodel ensemble mean THC weakens by 30% after 100 yr. All models simulate sonic weakening of the THC, but no model simulates a complete shutdown of the THC. The multimodel ensemble indicates that the surface air temperature could present a complex anomaly pattern with cooling south of Greenland and warming over the Barents and Nordic Seas. The Atlantic ITCZ tends to shift southward. In response to 1.0-Sv freshwater input, the THC switches off rapidly in all model simulations. A large cooling occurs over the North Atlantic. The annual mean Atlantic ITCZ moves into the Southern Hemisphere. Models disagree in terms of the reversibility of the THC after its shutdown. In general, the EMICs and AOGCMs obtain similar THC responses and climate changes with more pronounced and sharper patterns in the AOGCMs.

Factores determinantes de la variabilidad espacial de anchoveta peruana (Engraulis ringens) en el Pacífico Sudoriental

Los modelos de nicho ecológico permiten estudiar el efecto del ambiente sobre la distribución de las especies, relacionando datos de su distribución con información ambiental. El objetivo del presente estudio fue estimar el nicho ecológico y describir la variabilidad en la distribución espacial de la anchoveta (Engraulis ringens) mediante el uso de modelos estadísticos de nicho ecológico. Se trabajó con dos enfoques de análisis: por stocks (norte, centro y sur) en el Pacífico Sudoriental (PSO) y por estadios de desarrollo (pre-reclutas, reclutas y adultos) en la costa peruana. El modelo de nicho ecológico utilizó modelos aditivos generalizados, estimaciones georeferenciadas de presencia y ausencia de anchoveta e información de cuatro variables ambientales (temperatura superficial del mar, salinidad superficial del mar, concentración de clorofila a superficial y la profundidad de la oxiclina) entre los a˜nos 1985 y 2008. Se encontró que no existen diferencias en los nichos ecológicos de los tres stocks de anchoveta siendo los modelos que utilizaron la información de la anchoveta en todo el PSO los que lograron modelar el nicho de manera correcta. Respecto al análisis por estadios, se evidenció que cada estadio de desarrollo tiene distintas tolerancias a las variables ambientales consideradas en este trabajo, siendo los nichos de estadios menos desarrollados los que estuvieron incluidos dentro de los estadios más desarrollados. Se recomienda realizar estudios separados para cada estadio de desarrollo, lo cual permita comprender mejor las relaciones ecológicas encontradas en los resultados del nicho ecológico. Además se recomienda realizar simulaciones con modelos de nicho que incluyan más variables ambientales, las cuales puedan mejorar los mapas de distribución espacial de la anchoveta para los dos enfoques de análisis.

Geochemistry of sediments from the upwelling off Morocco

The high-productive upwelling area off Morocco is part of one of the four major trade-wind driven continental margin upwelling zones in the world oceans. While coastal upwelling occurs mostly on the shelf, biogenic particles derived from upwelling are deposited mostly at the upper continental slope. Nutrient-rich coastal water is transported within the Cape Ghir filament region at 30°N up to several hundreds of kilometers offshore. Both upwelling intensity and filament activity are dependent on the strength of the summer Trades. This study is aimed to reconstruct changes in trade wind intensity over the last 250,000 years by the analysis of the productivity signal contained in the sedimentary biogenic particles of the continental slope and beneath the Cape Ghir filament. Detailed geochemical and geophysical analyses (TOC, carbonate, C/N, delta13Corg, delta15N, delta13C of benthic foraminifera, delta18O of benthic and planktic foraminifera, magnetic susceptibility) have been carried out at two sites on the upper continental slope and one site located further offshore influenced by the Cape Ghir filament. A second offshore site south of the filament was analyzed (TOC, magnetic susceptibility) to distinguish the productivity signal related to the filament signal from the general offshore variability. Higher productivity during glacial times was observed at all four sites. However, the variability of productivity during glacial times was remarkably different at the filament-influenced site compared to the upwelling-influenced continental slope sites. In addition to climate-related changes in upwelling intensity, zonal shifts of the upwelling area due to sea-level changes have impacted the sedimentary productivity record, especially at the continental slope sites. By comparison with other proxies related to the strength and direction of the prevailing winds (Si/Al ratio as grain-size indicator, pollen) the productivity record at the filament-influenced site reflects mainly changes in trade-wind intensity. Our reconstruction reveals that especially during glacial times trade-wind intensity was increased and showed a strong variability with frequencies related to precession.

The relative benefits of endurance and strength training on the metabolic factors and muscle function of people with type 2 diabetes mellitus

Objective: To compare the effects of a 4-month strength training (ST) versus aerobic endurance training (ET) program on metabolic control, muscle strength, and cardiovascular endurance in subjects with type 2 diabetes mellitus (T2D). Design: Randomized controlled trial. Setting: Large public tertiary hospital. Participants: Twenty-two T21) participants (I I men, I I women; mean age +/- standard error, 56.2 +/- 1.1 y; diabetes duration, 8.8 +/- 3.5y) were randomized into a 4-month ST program and 17 T2D participants (9 men, 8 women; mean age, 57.9 +/- 1.4y; diabetes duration, 9.2 +/- 1.7y) into a 4-month ET program. Interventions: ST (up to 6 sets per muscle group per week) and ET (with an intensity of maximal oxygen consumption of 60% and a volume beginning at 15min and advancing to a maximum of 30min 3X/wk) for 4 months. Main Outcome Measures: Laboratory tests included determinations of blood glucose, glycosylated hemoglobin (Hb A(1c)), insulin, and lipid assays. Results: A significant decline in Hb A, was only observed in the ST group (8.3% +/- 1.7% to 7.1% +/- 0.2%, P=.001). Blood glucose (204 +/- 16mg/dL to 147 +/- 8mg/dL, P <.001) and insulin resistance (9.11 +/- 1.51 to 7.15 +/- 1.15, P=.04) improved significantly in the ST group, whereas no significant changes were observed in the ET group. Baseline levels of total cholesterol (207 +/- 8mg/dL to 184 +/- 7mg/dL, P <.001), low-density lipoprotein cholesterol (120 +/- 8mg/dL to 106 +/- 8mg/dL, P=.001), and triglyceride levels (229 +/- 25mg/dL to 150 +/- 15mg/dL, P=.001) were significantly reduced and high-density lipoprotein cholesterol (43 +/- 3mg/dL to 48 +/- 2mg/dL, P=.004) was significantly increased in the ST group; in contrast, no such changes were seen in the ET group. Conclusions: ST was more effective than ET in improving glycemic control. With the added advantage of an improved lipid profile, we conclude that ST may play an important role in the treatment of T2D.