重离子辐照引起的金属/金属界面混合与相变研究

本论文用重离子在室温下辐照Fe/Cu(Si/Fe(10nm)/[Cu(2.5nm)/Fe(2.5nm)]8/Cu(5n m)、Si/Fe(10nm)/[Cu(4nm)/Fe(4nm)]5(8)/Cu(4nm)、Si/[Fe(10nm)/Cu(10nm)]5)和Fe/Nb(Si /[Fe(10nm)/Nb(4nm)/Fe(4nm)/Nb(4nm)]2/[Fe(4nm)/Nb(4nm)]4))金属多层膜样品，然后利用X射线衍射谱、俄歇电子元素深度剖析谱、透射电子显微镜和振动样品磁强计对样品进行分析。主要研究界面原子混合、相变现象及其与离子辐照参数之间的关系。 1. 室温下用400 keV Xe离子辐照Fe/Cu(Si/Fe(10nm)/[Cu(2.5nm)/Fe(2.5nm)]8/Cu (5nm)、Si/Fe(10nm)/[Cu(4nm)/Fe(4nm)]5/Cu(4nm))和Fe/Nb多层膜。结果显示：随着辐照量的增加，离子辐照引起了Fe/Cu多层膜中Fe与Cu原子的混合和Cu基fcc固溶体和Fe基bcc固溶体地出现；而在Fe/Nb多层膜中，离子辐照引起Fe与Nb原子的混合和FeNb固溶体和非晶态FeNb合金相的出现。随着样品的结构变化，样品的磁滞回线也发生了变化。 2. 室温下用2 MeV Xe离子辐照Fe/Cu和Fe/Nb多层膜。结果显示：随着辐照量的增加，首先发生Fe、Cu原子的偏析和界面锐化，接着发生混合，辐照量较大时形成Cu基fcc固溶体和Fe基bcc固溶体；而在Fe/Nb多层膜中，低辐照量辐照引起多层膜的界面锐化，高辐照量辐照引起Fe与Nb原子混合和FeNb固溶体和非晶态FeNb合金相的出现。随着样品的结构变化，样品的磁滞回线也发生了变化。 3. 室温下用2.03 GeV Kr离子辐照Fe/Cu和Fe/Nb多层膜。结果显示：对于Si/Fe(10nm)/[Cu(4nm)/Fe(4nm)]5/Cu(4nm)多层膜，辐照量为1.0×1013ions/cm2时，发生Fe、Cu原子的偏析和界面锐化；对于Si/[Fe(10nm)/Cu(10nm)]5多层膜，随着辐照量的增加，首先发生Fe、Cu原子的偏析和界面锐化，接着发生混合；对于Fe/Nb多层膜，低辐照量辐照引起多层膜的界面锐化，高辐照量辐照引起Fe与Nb原子混合。随着样品的结构变化，多层膜样品的磁滞回线也发生了变化。 4. 室温下用1.08 GeV Kr离子辐照Fe/Cu和Fe/Nb多层膜。结果显示：在Si/Fe(10nm)/[Cu(4nm)/Fe(4nm)]5/Cu(4nm)、Si/[Fe(10nm)/Cu(10nm)]5和Fe/Nb多层膜中，辐照引起Fe层与Cu（Nb）层混合。随着样品的结构变化，多层膜样品的磁滞回线也发生了变化。 最后，对重离子辐照引起多层膜界面原子混合及相变的机理进行了探讨

Study of beta-alpha recrystallization of the polypropylene

The crystalline modifications alpha and beta of polypropylene (PP) were studied by using polarized light microscopy (PLM), wide-angle X-ray diffraction (WAXD), and differential scanning calorimetry (DSC). Typically beta crystals surrounded by alpha spherulites were observed at low temperature. With increasing temperature the beta crystals melted and a new crystal appeared. More interestingly, the melting temperature of the new crystal was about 5degrees higher than that of alpha spherulites originally present in the sample formed isothermally. It was assumed that this new crystal was the recrystalline alpha crystal. This assumption was supported by the DSC results. Furthermore, the crystallization kinetics of the PP used was studied on the basis of the traditional Avrami analysis. As a result, the Avrami exponents of crystallization temperature from 120 to 130degreesC ranged between 4.21 and 3.60, indicating that the crystallization mechanism of PP order melt was spherulitic growth and random nucleation.

Direct formation of form I poly(1-butene) single crystals from melt crystallization in ultrathin films

The morphologies and crystalline structures of melt-crystallized ultrathin isotactic poly(1-butene) films have been studied with transmission electron microscopy and electron diffraction. It is demonstrated that a bypass of form II crystallization can be achieved with an increase in its crystallization temperature. Electron microscopy observations show that melt-grown isotactic poly(1-butene) single crystals have a well-shaped hexagonal form, whereas form I crystals converted from form II display the morphologies of their tetragonal precursors. Electron diffraction results indicate that, instead of the twinned hexagonal pattern of the converted form I crystal, the directly formed form I single crystals exhibit an untwinned hexagonal pattern.

TG-DTA properties of new nonlinear optical materials: K(2)Ln(NO3)(5)center dot 2H(2)O (Ln = La, Ce, Pr, Nd, Sm)

Single crystals of K(2)Ln(NO3)(5). 2H(2)O (KLnN) (Ln = La, Ce, Pr, Nd, Sm) were grown from aqueous solution. The thermogravimetric analysis and differential thermal analysis curves of KLnN demonstrate that the processes of dehydration, melting, irreversible phase transformation and decomposition of NO3- take place in sequence in the heating processes (except KCN). There are three stages in the decomposition of NO3- in KLnN (Ln = La, Nd, Sm) while two in KLnN (Ln = Ce, Pr). K(2)Ln(NO3)(5) is formed at about 225 degrees C by the reaction of KNO3 and Ln(NO3)(3). nH(2)O (Ln = La, Ce, Pr, Nd). (C) 2000 Elsevier Science Ltd. All rights reserved.

Mechanical and thermal induced chain conformational transformations in syndiotactic polypropylene (sPP)

Stretching a stacked sPP lamellar morphology at room temperature leads to a mechanical induced transformation from the (t(2)g(2))(2) (helical) into the (tttt) (zigzag) chain conformation of the polymer. The so prepared samples exhibit after annealing above 80 degreesC a thermal induced retransformation into the cell I and cell III crystal structure of the helical chain conformation. The mechanical induced chain conformational transformation as well as the thermal induced retransformation was studied by means of transmission electron microscopy and electron diffraction. (C) 2001 Kluwer Academic Publishers.

P wave velocity of the pumice from the Okinawa Trough at high temperature and high pressure.

P wave velocity of the pumice sample from the middle Okinawa Trough and andesite sample from vicinity Yingdao volcanic island, Kyushu Japan were measured at temperature (from room temperature to 1500 C) and pressure (from room pressure to 2.4GPa) using a multi-anvil pressure apparatus called the YJ-3000 press. The measured data shows that at low temperature and low pressure (<1GPa, <800degreesC), the P wave velocity of pumice is lower than that of andesite, while at high temperature and high pressure (>1GPa, >800degreesC) the P wave velocity of pumice and andesite. becomes consistent (5.9km/s). The paper points out that 1GPa/800degreesC is the point of thermodynamic phase transformation Okinawa Trough pumice and vicinity andesite, and the point is deeper than 18km.

UV Raman spectroscopic study on the synthesis mechanism of zeolite X

The synthesis of zeolite X is characterized by UV Raman spectroscopy, NMR spectroscopy, and X-ray diffraction. UV Raman spectra of the liquid phase of the synthesis system indicate that AI(OH); species are incorporated into silicate species, and the polymeric silicate species are depolymerized into monomeric silicate species during the early stage of zeolite formation. An. intermediate species possessing Raman bands at 307, 503, 858 and 1020 cm(-1) is detected during the crystallization ill the solid phase transformation. The intermediate species is attributed to the beta cage, the secondary building unit of zeolite X. A model for the formation of zeolite X is proposed, which involves four-membered rings connecting to each other via six-membered ring to form beta cages, then the beta cages interconnect via double six-membered rings to form the framework of zeolite X. (C) 2001 Elsevier Science B.V. All rights reserved.

Understanding thickness effects in thin film capacitors

Pulsed Laser Deposition (PLD) was used to make Au/(Ba0.5Sr0.5)TiO3/(La0.5Sr0.5) CoO3/MgO thin film capacitor structures. Functional properties were studied with changing BST thickness from similar to1265 nm to similar to63 nm. The dielectric constant was found to decrease, and migration of T-m (the temperature at which the dielectric constant is maximum) to lower temperatures occurred as thickness was reduced. Curie-Weiss plots of the as-obtained dielectric data, indicated that the Curie temperature was also systemmatically progressively depressed. Further, fitting to expressions previously used to describe diffuse phase transitions suggested increased diffuseness in transformation behaviour as film thickness decreased. This paper discusses the care needed in interpreting the observations given above. We make particular distinction between the apparent Curie-temperature derived from Curie-Weiss plots of as-measured data, and the inherent Curie temperature determined after correction for the interfacial capacitance. We demonstrate that while the apparent Curie temperature decreases as thickness decreases, the inherent Curie temperature is thickness independent. Thickness-invariant phase transition behaviour is confirmed from analysis of polarisation loops, and from examination of the temperature dependence of the loss-tangent. We particularly note that correction of data for interfacial capacitance does not alter the position of T-m. We must therefore conclude that the position of T-m is not related simply to phase transformation behaviour in BST thin films.

Scanning electron microscopy study of microstructural evolution of electroless nickel-phosphorus deposits with heat treatment

This paper follows previous X-ray diffraction work on crystallisation and phase transformation of electroless nickel–phosphorus deposits, concentrating on microstructural changes. Amorphous or nanocrystalline coatings, depending on their phosphorus content, were heat treated at temperatures between 100 and 500 °C for 1 h. Changes in microstructure after the heat treatment were examined using high-resolution field emission scanning electron microscope. Crystallisation and grain growth effects are observed, as well as some inherent defect structures in the coatings and their changes. These are compared with the previous X-ray diffraction work and in general, good agreement is observed. The complementary strength and weakness of the different characterisation techniques are discussed.

Thermal study of selectively plated nickel sulfamate coatings

Nickel sulfamate solution was applied to mild steel substrates by the process of selective plating. The coated samples were heated to temperatures in the range of 50–1000 °C. Thermal analysis, X-ray diffraction and microscopy techniques were used to investigate the effect of secondary heating on the microstructure, mechanical properties and the composition of the surface coatings.

The microscopy analysis showed that the secondary heating caused diffusion within the coating itself and diffusion between the coating and the substrate as concentrations of iron increased in the coating and nickel appeared in the substrate. This diffusion redistribution also caused a phase transformation in the coating as NiO formed on the surface when the coating was heated in a furnace fitted with a nitrogen flow. However this transformation was found not to occur when the coating was heated in a sealed helium environment. Layer and grain growth occurred as temperature increased with the grains taking their preferred orientation as they were heated.

The surface hardness was found to initially rise up from 565 HV to 600 HV when heated to 200 °C. After 200 °C the surface hardness decreased in two stages before falling to 110 HV by 1000 °C. During tensile testing the coated samples performed marginally better in tension than the uncoated samples, however the temperatures used were not elevated high enough to show any real degradation during the tensile testing of the nickel coating that was shown during hardness testing and the microscopy analysis

Microscopy of heat treated titanium alloy BT16

Metallographic characterisation is combined with statistical analysis to study the microstructure of a BT16 titanium alloy after different heat treatment processes. It was found that the length, width and aspect ratio of α plates in this alloy follow the three-parameter Weibull distribution. Increasing annealing temperature or time causes the probability distribution of the length and the width of α plates to tend toward a normal distribution. The phase transformation temperature of the BT16 titanium alloy was found to be 875±5°C.

Effect of post-weld-annealing on the tensile deformation characteristics of laser-welded NiTi thin foil

Laser welding is an important process for fabricating complex components involving NiTi shape memory
alloy. As welding is a thermal process, the amount of heat input and the rate of cooling have significant
impact on the microstructure and hence the resultant characteristics of NiTi. In this study, the effect of
laser welding and post-weld-annealing from 573 K to 1173 K on the thermal phase transformation behaviors,
tensile deformation and micro-hardness characteristics of the laser-welded NiTi thin foils were investigated.
It was found that the as-welded sample exhibited inferior super-elasticity compared to the base
material, and the super-elasticity could be partially restored by annealing at 573 K. On the other hand,
annealing of the weldment above the recrystallization temperature would lower the super-elasticity.

Effect of postweld heat treatment on the microstructure and cyclic deformation behavior of laser-welded NiTi-shape memory wires

NiTi wires of 0.5 mm diameter were laser welded using a CW 100-W fiber laser in an argon shielding environment with or without postweld heat-treatment (PWHT). The microstructure and the phases present were studied by scanning-electron microscopy (SEM), transmission-electron microscopy (TEM), and X-ray diffractometry (XRD). The phase transformation behavior and the cyclic stress–strain behavior of the NiTi weldments were studied using differential scanning calorimetry (DSC) and cyclic tensile testing. TEM and XRD analyses reveal the presence of Ni4Ti3 particles after PWHT at or above 623 K (350 °C). In the cyclic tensile test, PWHT at 623 K (350 °C) improves the cyclic deformation behavior of the weldment by reducing the accumulated residual strain, whereas PWHT at 723 K (450 °C) provides no benefit to the cyclic deformation behavior. Welding also reduces the tensile strength and fracture elongation of NiTi wires, but the deterioration could be alleviated by PWHT.