(Table 1, page 41), Chemical and radiocativity analysis of manganese crusts from the Lika river, Vermland, Sweden and ferromanganese ore from lake Tisjoen, Dalecarlia, Sweden

The trace element content of different bog ores has been measured and it appeared that most of these elements are enriched in the manganiferous bog ores as compared with the ferriferous ones. The manganiferous bog ores have also proved to have a higher radioactivity than the ferriferous ones.

(Table, Appendix C) Metal content of nodules at Sea Scope stations based upon XRF analyses at the Ore Microscopy Laboratory, Washington State Unicersity, USA

New information on possible resource value of sea floor manganese nodule deposits in the eastern north Pacific has been obtained by a study of records and collections of the 1972 Sea Scope Expedition. Nodule abundance (percent of sea floor covered) varies greatly, according to photographs from eight stations and data from other sources. All estimates considered reliable are plotted on a map of the region. Similar maps show the average content of Ni, Cu, Mn and Co at 89 stations from which three or more nodules were analyzed. Variations in nodule metal content at each station are shown graphically in an appendix, where data on nodule sizes are also given. Results of new analyses of 420 nodules from 93 stations for mn, fe, ni, cu, CO, and zn are listed in another appendix. Relatively high Ni + Cu content is restricted chiefly to four groups of stations in the equatorial region, where group averages are 1.86, 1.99, 2.47, and 2.55 weight-percent. Prepared for United States Department of the Interior, Bureau of Mines. Grant no. GO284008-02-MAS. - NTIS PB82-142571.

Contents of metal cations exchange capacity of ore minerals in ferromanganese micronodules from the Atlantic, Indian and Pacific Oceans

Results of experimental studies of ion exchange properties of manganese and iron minerals in micronodules from diverse bioproductive zones of the World Ocean were considered. It was found that sorption behavior of these minerals was similar to that of ore minerals from ferromanganese nodules and low-temperature hydrothermal crusts. The exchange complex of minerals in the micronodules includes the major (Na**+, K**+, Ca**2+, Mg**2+, and Mn**2+) and subordinate (Ni**2+, Cu**2+, Co**2+, Pb**2+, and others) cations. Reactivity of theses cations increases from Pb**2+ and Co**2+ to Na**+ and Ca**2+. Exchange capacity of micronodule minerals increases from alkali to heavy metal cations. Capacity of iron and manganese minerals in oceanic micronodules increases in the following series: goethite < goethite + birnessite < todorokite + asbolane-buserite + birnessite < asbolane-buserite + birnessite < birnessite + asbolane-buserite < birnessite + vernadite ~= Fe-vernadite + Mn-feroxyhyte. Obtained data supplement available information on ion exchange properties of oceanic ferromanganese sediments and refine the role of sorption processes in redistribution of metal cations at the bottom water - sediment interface during micronodule formation and growth.

Understanding arsenic mobility and speciation in lake sediments impacted by ore roasting near Giant mine, NWT

The roasting of gold-bearing arsenopyrite at Giant mine (Northwest Territories) between 1949 and 1999 released approximately 20,000 tonnes of toxic arsenic-bearing aerosols in the local aerial environment. Detailed examination of lake sediments, sediment porewaters, surface waters and lake hydrology sampled from three lakes of differing limnological characteristics was conducted in summer and winter conditions. Samples were analyzed for solid and dissolved elemental concentrations, speciation and mineralogy. The three lakes are located less than 5km from the mine roaster, and downwind, based on predominant wind direction. The objective of the study was to assess the controls on the mobility and fate of arsenic in these roaster-impacted subarctic lacustrine environments. Results show that the occurrence of arsenic trioxide in lake sediments coincides with the regional onset of industrial activities. The bulk of arsenic in sediments is contained in the form of secondary sulphide precipitates, with iron oxides hosting a minimal amount of arsenic near the surface-water interface. The presence of geogenic arsenic is likely contained as dilute impurities in common rock-forming minerals, and is not believed to be a significant source of arsenic to sediments, porewaters or lake waters. Furthermore, the well correlated depth-profiles of arsenic, antimony and gold in sediments may help reveal roaster impact. The soluble arsenic trioxide particles contained in sediments act as the primary source of arsenic into porewaters. Dissolved arsenic in reducing porewaters both precipitate as secondary sulphides in situ, and diffuse upwards into the overlying lake waters. Arsenic diffusion out of porewaters, combined with watercourse-driven residence time, are estimated to be the predominant mechanisms controlling arsenic concentrations in overlying lake waters. The sequestration of arsenic from porewaters as sulphide precipitates, in the study lakes, is not an effective process in keeping lake-water arsenic concentrations below guidelines for the protection of the freshwater environment and drinking water. Seasonal impacts on lake geochemistry derive from ice covering lake waters, cutting them off from of atmospheric oxygen, along with the exclusion of solutes from the ice. Such effects are limited in deep lakes but are can be an important factor controlling arsenic precipitation and mobility in ponds.

Study of the behavior of iron ore particles in spiral concentrators

Les spirales sont des appareils de séparation gravimétrique principalement utilisés dans l’industrie du traitement du minerai de fer. La classification des particules dans la pulpe s’effectue lors de la descente dans les spires en fonction de leur taille et leur densité, des conditions d’opération et de la géométrie de la spirale. L’effet des conditions d’opération (pourcentage solide, débit d’alimentation et débit d’eau de lavage) est évalué sur la performance des spirales en utilisant une spirale WW6E installée à COREM pour traiter un minerai de fer de ArcelorMittal, Québec. Les résultats montrent l’effet dominant du débit de l’eau de lavage et son impact majeur sur les particules grossières. Un circuit fermé de trois spirales parallèles avec 3, 5 et 7 tours est utilisé afin d’évaluer l’influence du nombre de tours. Les résultats préliminaires indiquent que la spirale trois tours fonctionne bien pour le nettoyage tandis que la 7 tour est robuste pour l’ébauchage et l’épuisage.

Nickel isotope fractionation during laterite Ni ore smelting and refining: implications for tracing the sources of Ni in smelter-affected soils

Nickel isotope ratios were measured in ores, fly ash, slags and FeNi samples from two metallurgical plants located in the Goiás State, Brazil (Barro Alto, Niquelândia). This allowed investigating the mass-dependent fractionation of Ni isotopes during the Ni-laterite ore smelting and refining. Feeding material exhibits a large range of δ60Ni values (from 0.02 ± 0.10 ‰ to 0.20 ± 0.05 ‰, n=7), explained by the diversity of Ni-bearing phases, and the average of δ60Nifeeding materials was found equal to 0.08 ± 0.08‰ (2SD, n=7). Both δ60Ni values of fly ash (δ60Ni = 0.07 ± 0.07‰, n=10) and final FeNi produced (0.05 ± 0.02 ‰, n=2) were not significantly different from the feeding materials ones. These values are consistent with the very high production yield of the factories. However, smelting slags present the heaviest δ60Ni values of all the smelter samples, with δ60Ni ranging from 0.11 ± 0.05 ‰ to 0.27 ± 0.05 ‰ (n=8). Soils were also collected near and far from the Niquelândia metallurgical plant, to evaluate the potential of Ni isotopes for tracing the natural vs anthropogenic Ni in soils. The Ni isotopic composition of the non-impacted topsoils developed on ultramafic rocks ranges from -0.26 ± 0.09 ‰ to -0.04 ± 0.05 ‰ (n=20). On the contrary, the Ni isotopic composition of the non-ultramafic topsoils, collected close to the plant, exhibit a large variation of δ60Ni, ranging from -0.19 ± 0.13 ‰ up to 0.10 ± 0.05 ‰ (n=4). This slight but significant enrichment in heavy isotopes highlight the potential impact of smelting activity in the surrounding area, as well as the potential of Ni isotopes for discerning anthropogenic samples (heavier δ60Ni values) from natural ones (lighter δ60Ni values). However, given the global range of published δ60Ni values (from -1.03 to 2.5 ‰) and more particularly those associated to natural weathering of ultramafic rocks (from -0.61 to 0.32‰), the use of Ni isotopes for tracing environmental contamination from smelters will remain challenging.

Dephosphorization of Iron Ore through Bioleaching

Phosphorus, as phosphate, is frequently found as a constituent of many of the world iron resources. Phosphorus is an extremely harmful element found in iron ore used as a raw material in the steelmaking process because it will affect the quality of iron and steel products. Allowable phosphorus concentration in high quality steel is usually less than 0.08%. Dephosphorization of iron ore has been studied for a long time. Although there are described physical beneficiation and chemical leaching processes, involving inorganic acids, to reduce phosphorus content of iron ores, these processes have several limitations such as poor recovery, require high energy quantity, capital costs and cause environmental pollution. Use of microorganisms in leaching of mineral ores is gaining importance due to the implementation of stricter environmental rules. Microbes convert metal compounds into their water soluble forms and are biocatalysts of leaching processes. Biotechnology is considered as an eco-friendly, promising, and revolutionary solution to these problems. Microorganisms play a critical role in natural phosphorus cycle and the process of phosphate solubilization by microorganisms has been known for many years. This study was performed to analyze the possibility of using bioleaching as a process for the dephosphorization of an iron ore from Northeast of Portugal. For bioleaching, Acidithiobacillus ferrooxidans bacterium were used. For this study two experiments were done with different conditions, which lasts 6 weeks for first experiment and 5 weeks for second experiment. From the result of these preliminary studies, it was observed that for first experiment 6.2 % and for second experiment 3.7 % of phosphorus was removed from iron ore.

Effect of Cocoa ( Theobroma cacao ) Plantation Types on the Distribution of Anuran Communities in Ore, Ondo State, Nigeria

Anuran species diversity and abundance were evaluated in different farming status of cocoa plantation in Ore, Ondo State, Nigeria. Applying the combination of visual encounter survey (VES) and acoustical survey (AES), the different farms surveyed were categorized as; 1) pure cocoa farms with pesticides applied (PCWP); 2) pure cocoa farms without pesticides application; 3) intercropped cocoa farms with pesticides applied (ICWP); and 4) intercropped cocoa farms without pesticides application (ICNP). The surrounding primary/secondary forest (PSFV) was sampled applying the transect method. A mean total of 690±2.6 anurans belonging to 28 species, 14 genera and 9 families were recorded during the study. Out of these, 10, 19, 17, 22 and 26 species were recorded respectively from PCWP, PCNP, ICWP, ICNP and PSFV. The anuran species richness was significantly different between the different cocoa plantation status and the forest sites (F4, 10 = 20.55, P< 0.01). The highest mean number of individuals (190±9.5) was observed at ICNP followed by PSFV (183±5.7), while the least was at PCWP (77±8.0). There was also significant difference (F4, 10 = 150.48, P< 0.01) between the abundance of anuran species at the various sites. Diversity indices (Shannon and Margalef) showed that the forest sites had the greatest (3.204 and 4.799) respectively while the pesticide using pure cocoa farms had the least (1.853 and 2.072). Generally, the result of the study clearly indicated that pesticide use cocoa farms were significantly lower compared to other sites. Farmers are encouraged to engage in intercropping (polyculture) especially with food and economic crops in a biodiversity friendly manner which could have similar characteristics of a natural ecosystem, thereby enhancing the biological diversity of agro-ecosystems.

Arsenic bioleaching in medical realgar ore and arsenicbearing refractory gold ore by combination of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans

Purpose: To develop a novel biotechnological method for removing toxic arsenic from two kinds of representative arsenic-containing ores using different mixed mesophilic acidophiles. Methods: Bioleaching of the two types of arsenic-containing ores by mixed arsenic-unadapted Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans or mixed arsenic-adapted cultures, were carried out. Arsenic bioleaching ratios in the various leachates were determined and compared. Results: The results showed that the maximum arsenic leaching ratio obtained from realgar in the presence of mixed adapted cultures was 28.6 %. However, the maximum arsenic leaching ratio from realgar in the presence of mixed unadapted strains was only 12.4 %. Besides, maximum arsenic leaching ratios from arsenic-bearing refractory gold ore by mixed adapted strains or unadapted strains were 45.0 and 22.9 %, respectively. Oxidation of these two ores by sulfuric acid was insignificant, as maximum arsenic leaching ratios of realgar and arsenic-bearing refractory gold ore in the absence of any bacterium were only 2.8 and 11.2 %, respectively. Conclusion: Arsenic leaching ratio of realgar and refractory gold ore can be enhanced significantly in the presence of arsenic-adapted mesophilic acidophiles.

FACTORS INFLUENCING MATERIAL LOSS DURING IRON ORE PELLET HANDLING

Iron ore concentrate pellets have the potential to fracture and abrade during transportation and handling, which produces unwanted fine particulates and dust. Consequently, pellet producers characterize the abrasion resistance of their pellets, using an Abrasion Index (AI), to indicate whether their products will produce unacceptable levels of fines. However, no one has ever investigated whether the AI correlates to pellet dustiness. During the course of this research, we investigated the relationship between AI and iron ore concentrate pellet dustiness using a wide range of industrial and laboratory pellet samples. The results showed that, in general, AI can be used to indicate high levels of dust. However, for good-quality pellets, there was no correlation between the two. Thus, dust generation from shipping and handling pellets will depend on the quantity of pellets handled and how much they are handled. These results also showed that the type of industrial furnace used to harden iron ore concentrate pellets may affect their fines generation and potential dustiness.

A Study of the Microwave Carbothermic Reduction of Chromite Ore

Microwave reduction testing using activated charcoal as a reducing agent was performed on a sample of Black Thor chromite ore from the Ring of Fire deposit in Northern Ontario. First, a thermodynamic model was constructed for the system. Activity coefficients for several species were found in the literature. The model predicted chromium grades of 61.60% and recoveries of 93.43% for a 15% carbon addition. Next, reduction testing on the chromite ore was performed. Tests were performed at increasing power levels and reduction times. Testing atmospheres used were air, argon, and vacuum. The reduced product had maximum grades of 72.89% and recoveries of 80.37%. These maximum values were obtained in the same test where an argon atmosphere was used, with a carbon addition of 15%, optimal power level of 1200 W (actual 1171 W), and a time of 400 seconds. During this test, 17.53% of the initial mass was lost as gas, a carbon grade of 1.95% was found for the sintered core product. Additional work is recommended to try and purify the sintered core product as well as reduce more of the initial sample. Changing reagent schemes or a two step reduction / separation process could be implemented.

Spontaneous infiltrations of compound systems of Y(2)O(3), Sm(2)O(3), RE(2)O(3), Al(2)O(3) and AIN in SiC ceramics

Silicon carbide ceramics (SiC) are used in different applications in the engineering area due to the excellent properties, mainly in high temperatures. They are usually obtained by liquid-phase sintering enabling to form volatile products and, consequently, defects. The present work aims at studying the obtention of SiC ceramics by spontaneous infiltration using a eutectic composition of the Al(2)O(3)/Y(2)O(3), AIN/Y(2)O(3), Al(2)O(3)/Sm(2)O(3), AlN/Sm(2)O(3), Al(2)O(3)/RE(2)O(3) and AlN/RE(2)O(3) Systems. RE(2)O(3) is the concentrate of the rare-earth oxide obtained from Xenotime ore. Infiltration tests were carried out in argon atmosphere, graphite crucibles, in several temperatures near the melting point of each system, varying from 2.5 to 60 min. It was observed that Al(2)O(3)/Y(2)O(3), Al(2)O(3)/SM(2)O(3), AlN/SM(2)O(3) and Al(2)O(3)/RE(2)O(3) systems do not infiltrate appropriately and the AlN/Y(2)O(3) and AlN/RE(2)O(3) systems infiltrated spontaneously more than 20 mm; however, the first one presented a higher degree of infiltration, approximately 97%. (C) 2009 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Influência da função distribuição de quebra na modelagem e simulação do circuito de moagem de Carajás - Parte 1 - ajuste de modelos

The perfect mixing model (PMM) is based on parameters derived from the equipment characteristics as well as ore breakage characteristics. Ore characteristics are represented through the appearance function. This function may be determined using JKMRC laboratorial methods or by standard functions. This work describes the model fitting process of the Carajas grinding circuit, using the JKSimMet simulator Two scenarios were used in model fitting exercises: 1) standard appearance function; and 2) appearance fund ion based on testing carried out on samples taken at circuit feed. From this assessment, the appearance function`s influence in the PMM,fit and it`s relation with the breakage rate were determined. The influence of the appearance function on the respective breakage rate distribution was assessed.

Estudo de variabilidade e otimização do circuito de moagem SAG da Usina do Sossego

Sossego was the first Vale SAG mill operation to process copper-gold ore. It is located in the State of Para, southeastern Amazon region of Brazil. In the first three years of continuous operation, Vale investigated different alternatives for improving the circuit`s performance by investigating operating conditions, mainly focusing on the SAG mill. It was decided to further assess the performance of the comminution circuit as a function of ore characteristics. A comprehensive ore characterization program was then conducted, together with the calibration of mathematical models on the basis of surveys carried out at the industrial circuit. The simulator was then used to predict the throughput associated to each ore type, as well as to establish the optimized circuit configuration and tailored operating conditions. This paper describes in detail the main aspects of optimizing the industrial circuit performance, as well as the successful method for predicting the production as a function of ore characteristics and circuit configuration.