Dynamic modeling, simulation and control design of a parafoil-payload system for ship launched aerial delivery system (SLADS)

The objective of this research was to develop a high-fidelity dynamic model of a parafoilpayload system with respect to its application for the Ship Launched Aerial Delivery System (SLADS). SLADS is a concept in which cargo can be transfered from ship to shore using a parafoil-payload system. It is accomplished in two phases: An initial towing phase when the glider follows the towing vessel in a passive lift mode and an autonomous gliding phase when the system is guided to the desired point. While many previous researchers have analyzed the parafoil-payload system when it is released from another airborne vehicle, limited work has been done in the area of towing up the system from ground or sea. One of the main contributions of this research was the development of a nonlinear dynamic model of a towed parafoil-payload system. After performing an extensive literature review of the existing methods of modeling a parafoil-payload system, a five degree-of-freedom model was developed. The inertial and geometric properties of the system were investigated to predict accurate results in the simulation environment. Since extensive research has been done in determining the aerodynamic characteristics of a paraglider, an existing aerodynamic model was chosen to incorporate the effects of air flow around the flexible paraglider wing. During the towing phase, it is essential that the parafoil-payload system follow the line of the towing vessel path to prevent an unstable flight condition called ‘lockout’. A detailed study of the causes of lockout, its mathematical representation and the flight conditions and the parameters related to lockout, constitute another contribution of this work. A linearized model of the parafoil-payload system was developed and used to analyze the stability of the system about equilibrium conditions. The relationship between the control surface inputs and the stability was investigated. In addition to stability of flight, one more important objective of SLADS is to tow up the parafoil-payload system as fast as possible. The tension in the tow cable is directly proportional to the rate of ascent of the parafoil-payload system. Lockout instability is more favorable when tow tensions are large. Thus there is a tradeoff between susceptibility to lockout and rapid deployment. Control strategies were also developed for optimal tow up and to maintain stability in the event of disturbances.

Critical evaluation of diameter increment modelling in the Great Lakes region

Simulations of forest stand dynamics in a modelling framework including Forest Vegetation Simulator (FVS) are diameter driven, thus the diameter or basal area increment model needs a special attention. This dissertation critically evaluates diameter or basal area increment models and modelling approaches in the context of the Great Lakes region of the United States and Canada. A set of related studies are presented that critically evaluate the sub-model for change in individual tree basal diameter used in the Forest Vegetation Simulator (FVS), a dominant forestry model in the Great Lakes region. Various historical implementations of the STEMS (Stand and Tree Evaluation and Modeling System) family of diameter increment models, including the current public release of the Lake States variant of FVS (LS-FVS), were tested for the 30 most common tree species using data from the Michigan Forest Inventory and Analysis (FIA) program. The results showed that current public release of the LS-FVS diameter increment model over-predicts 10-year diameter increment by 17% on average. Also the study affirms that a simple adjustment factor as a function of a single predictor, dbh (diameter at breast height) used in the past versions, provides an inadequate correction of model prediction bias. In order to re-engineer the basal diameter increment model, the historical, conceptual and philosophical differences among the individual tree increment model families and their modelling approaches were analyzed and discussed. Two underlying conceptual approaches toward diameter or basal area increment modelling have been often used: the potential-modifier (POTMOD) and composite (COMP) approaches, which are exemplified by the STEMS/TWIGS and Prognosis models, respectively. It is argued that both approaches essentially use a similar base function and neither is conceptually different from a biological perspective, even though they look different in their model forms. No matter what modelling approach is used, the base function is the foundation of an increment model. Two base functions – gamma and Box-Lucas – were identified as candidate base functions for forestry applications. The results of a comparative analysis of empirical fits showed that quality of fit is essentially similar, and both are sufficiently detailed and flexible for forestry applications. The choice of either base function in order to model diameter or basal area increment is dependent upon personal preference; however, the gamma base function may be preferred over the Box-Lucas, as it fits the periodic increment data in both a linear and nonlinear composite model form. Finally, the utility of site index as a predictor variable has been criticized, as it has been widely used in models for complex, mixed species forest stands though not well suited for this purpose. An alternative to site index in an increment model was explored, using site index and a combination of climate variables and Forest Ecosystem Classification (FEC) ecosites and data from the Province of Ontario, Canada. The results showed that a combination of climate and FEC ecosites variables can replace site index in the diameter increment model.

Risk of severe asthma episodes predicted from fluctuation analysis of airway function

Asthma is an increasing health problem worldwide, but the long-term temporal pattern of clinical symptoms is not understood and predicting asthma episodes is not generally possible. We analyse the time series of peak expiratory flows, a standard measurement of airway function that has been assessed twice daily in a large asthmatic population during a long-term crossover clinical trial. Here we introduce an approach to predict the risk of worsening airflow obstruction by calculating the conditional probability that, given the current airway condition, a severe obstruction will occur within 30 days. We find that, compared with a placebo, a regular long-acting bronchodilator (salmeterol) that is widely used to improve asthma control decreases the risk of airway obstruction. Unexpectedly, however, a regular short-acting beta2-agonist bronchodilator (albuterol) increases this risk. Furthermore, we find that the time series of peak expiratory flows show long-range correlations that change significantly with disease severity, approaching a random process with increased variability in the most severe cases. Using a nonlinear stochastic model, we show that both the increased variability and the loss of correlations augment the risk of unstable airway function. The characterization of fluctuations in airway function provides a quantitative basis for objective risk prediction of asthma episodes and for evaluating the effectiveness of therapy.

Genetic variation and demographic history of the Haplochromis laparogramma group of Lake Victoria-An analysis based on SINEs and mitochondrial DNA

More than 500 endemic haplochromine cichlid species inhabit Lake Victoria. This striking species diversity is a classical example of recent explosive adaptive radiation thought to have happened within the last similar to 15,000 years. In this study, we examined the population structure and historical demography of 3 pelagic haplochromine cichlid species that resemble in morphology and have similar niche, Haplochromis (Yssichromis) laparogramma, Haplochromis (Y.) pyrrhocephalus, and Haplochromis (Y.) sp. "glaucocephalus". We investigated the sequences of the mitochondrial DNA control region and the insertion patterns of short interspersed elements (SINEs) of 759 individuals. We show that sympatric forms are genetically differentiated in 4 of 6 cases, but we also found apparent weakening of the genetic differentiation in areas with turbid water. We estimated the timings of population expansion and species divergence to coincide with the refilling of the lake at the Pleistocene/Holocene boundary. We also found that estimates can be altered significantly by the choice of the shape of the molecular clock. If we employ the nonlinear clock model of evolutionary rates in which the rates are higher towards the recent, the population expansion was dated at around the event of desiccation of the lake ca. 17,000 YBP. Thus, we succeeded in clarifying the species and population structure of closely related Lake Victoria cichlids and in showing the importance of applying appropriate clock calibrations in elucidating recent evolutionary events. (C) 2009 Elsevier B.V. All rights reserved.

Finite element analysis predicts experimental failure patterns in vertebral bodies loaded via intervertebral discs up to large deformation

Vertebral compression fracture is a common medical problem in osteoporotic individuals. The quantitative computed tomography (QCT)-based finite element (FE) method may be used to predict vertebral strength in vivo, but needs to be validated with experimental tests. The aim of this study was to validate a nonlinear anatomy specific QCT-based FE model by using a novel testing setup. Thirty-seven human thoracolumbar vertebral bone slices were prepared by removing cortical endplates and posterior elements. The slices were scanned with QCT and the volumetric bone mineral density (vBMD) was computed with the standard clinical approach. A novel experimental setup was designed to induce a realistic failure in the vertebral slices in vitro. Rotation of the loading plate was allowed by means of a ball joint. To minimize device compliance, the specimen deformation was measured directly on the loading plate with three sensors. A nonlinear FE model was generated from the calibrated QCT images and computed vertebral stiffness and strength were compared to those measured during the experiments. In agreement with clinical observations, most of the vertebrae underwent an anterior wedge-shape fracture. As expected, the FE method predicted both stiffness and strength better than vBMD (R2 improved from 0.27 to 0.49 and from 0.34 to 0.79, respectively). Despite the lack of fitting parameters, the linear regression of the FE prediction for strength was close to the 1:1 relation (slope and intercept close to one (0.86 kN) and to zero (0.72 kN), respectively). In conclusion, a nonlinear FE model was successfully validated through a novel experimental technique for generating wedge-shape fractures in human thoracolumbar vertebrae.

Eigenstructure Assignment Based Controllers Applied to Flexible Spacecraft

The objective of this paper is to evaluate the behaviour of a controller designed using a parametric Eigenstructure Assignment method and to evaluate its suitability for use in flexible spacecraft. The challenge of this objective lies in obtaining a suitable controller that is specifically designated to alleviate the deflections and vibrations suffered by external appendages in flexible spacecraft while performing attitude manoeuvres. One of the main problems in these vehicles is the mechanical cross-coupling that exists between the rigid and flexible parts of the spacecraft. Spacecraft with fine attitude pointing requirements need precise control of the mechanical coupling to avoid undesired attitude misalignment. In designing an attitude controller, it is necessary to consider the possible vibration of the solar panels and how it may influence the performance of the rest of the vehicle. The nonlinear mathematical model of a flexible spacecraft is considered a close approximation to the real system. During the process of controller evaluation, the design process has also been taken into account as a factor in assessing the robustness of the system.

The Dynamics of High-Speed Railway Bridges: A Review of Design Issues and New Research for Lateral Dynamics

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for the consideration of safe running conditions for the trains. In this work we start by reviewing the relevance of some basic design aspects. The significance of impact factor envelopes for moving loads is considered first. Resonance which may be achieved for high-speed trains requires dynamic analysis, for which some key aspects are discussed. The relevance of performing a longitudinal distribution of axle loads, the number of modes taken in analysis, and the consideration of vehicle-structure interaction are discussed with representative examples. The lateral dynamic effects of running trains on bridges is of importance for laterally compliant viaducts, such as some very tall structures erected in new high-speed lines. The relevance of this study is mainly for the safety of the traffic, considering both internal actions such as the hunting motion as well as external actions such as wind or earthquakes [1]. These studies require three-dimensional dynamic coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework [2]. The wheel-rail contact has been considered using a FastSim algorithm which provides a compromise between accuracy and computational cost, and captures the main nonlinear response of the contact interface. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the dynamic interaction between bridge and vehicle. The second application is to a real HS viaduct with a long continuous deck and tall piers and high lateral compliance [3]. The results show the safety of the traffic as well as the importance of considering features such as track alignment irregularities.

Analysis of lateral dynamics of railway vehicles on viaducts with coupled models

The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require 3D coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a br idge, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle. The second application is to a real viaduct in a high-speed line, with a long continuous deck and tall piers with high lateral compliance. The results show the safety of the traffic as well as the relevance of considering the wind action and the nonlinear response.

Coupled models for the dynamics of bridges under high-speed rail traffic

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for determining safe running conditions of trains. In this work we start by reviewing the relevance of some basic moving load models for the dynamic action of vertical traffic loads. The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require 3D coupled vehicle-bridge models and consideration of wheel to rail contact. We describe here a fully nonlinear coupled model, formulated in absolute coordinates and incorporated into a commercial finite element framework. An application example is presented for a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle.

Análisis de elementos de madera reforzados con materiales compuestos

Gran parte del patrimonio construido cuenta con edificios cuya estructura está compuesta por elementos de madera. El volumen económico que supone el mantenimiento y renovación de dicho patrimonio es considerable, por ello, es de especial interés el estudio de las diferentes técnicas de refuerzo aplicables a este tipo de estructuras. Las estructuras de madera han sido tradicionalmente reforzadas con piezas del mismo material, aumentando la sección de los elementos dañados, o con acero. La aparición de los materiales compuestos de polímeros reforzados con fibras, y su progresiva aplicación en obras de construcción, hizo que a principios de la década de los noventa se comenzara a aplicar este material en refuerzos de estructuras de madera (Puente de Sins, 1992). La madera es un material natural con una excelente relación entre sus características mecánicas y su peso. Con el uso de materiales compuestos como refuerzo ésta característica se mantiene. En cuanto a su modelo constitutivo, se admite un comportamiento elástico lineal a tracción paralela a la fibra hasta la rotura, mientras que a compresión, se considera un comportamiento lineal elástico inicial, seguido de un tramo plástico. En vigas de madera aserrada sometidas a flexión predomina el modo de fallo por tracción localizándose la fractura frecuentemente en el canto inferior. Los FRP tienen un comportamiento elástico lineal a tracción hasta la rotura y cuentan con excelentes propiedades mecánicas en relación a su peso y volumen. Si se refuerza la viga por el canto inferior se aumentará su capacidad de absorber tracciones y por tanto, es previsible que se produzca un incremento en la capacidad de carga, así como un aumento de ductilidad. En este trabajo se analizan los beneficios que aportan distintos sistemas de refuerzos de materiales compuestos. El objetivo es contribuir al conocimiento de esta técnica para la recuperación o aumento de las propiedades resistentes de elementos de madera sometidos a flexión. Se ha llevado a cabo un estudio basado en datos obtenidos experimentalmente mediante el ensayo a flexión de vigas de madera de pino silvestre reforzadas con materiales compuestos. Las fibras que componen los tejidos utilizados para la ejecución de los refuerzos son de basalto y de carbono. En el caso de los compuestos de fibra de basalto se aplican en distintos gramajes, y los de carbono en tejido unidireccional y bidireccional. Se analiza el comportamiento de las vigas según las variables de refuerzo aplicadas y se comparan con los resultados de vigas ensayadas sin reforzar. Además se comprueba el ajuste del modelo de cálculo no lineal aplicado para predecir la carga de rotura de cada viga reforzada. Con este trabajo queda demostrado el buen funcionamiento del FRP de fibra de basalto aplicado en el refuerzo de vigas de madera y de los tejidos de carbono bidireccionales con respecto a los unidireccionales. ABSTRACT Many of the buildings of the built heritage include a structure composed by timber elements. The economic volume involved in the maintenance and renewal of this built heritage is considerable, therefore, the study of the different reinforcement techniques applicable to this type of structure is of special interest. The wooden structures have traditionally been reinforced either with steel or with pieces of the same material, increasing the section of the damaged parts. The emergence of polymer composites reinforced with fibers, and their progressive use in construction, started to be applied as reinforcement in timber structures at the beginning of the nineties decade in the 20th century (Sins Bridge, 1992). Wood is a natural material with an excellent ratio between its mechanic characteristics and its weight. This feature is maintained with the use of composites as reinforcement. In terms of its constitutive model, linear elastic behavior parallel to the fiber up to fracture is admitted when subjected to tensile stress, while under compression, an initial linear elastic behavior, followed by a section plasticizing, is considered. In sawn timber beams subjected to bending, the predominant failure is mainly due to tensile stress; and frequently the fracture is located at the beam lower face. The FRP have a linear elastic behavior until fracture occurs, and have excellent mechanical properties in relation to their weight and volume. If the beam is reinforced by its lower face, its capacity to absorb tensile stresses will increase, and therefore, an increase in its carrying capacity is likely to be produced, as well as an increase in ductility. This work analyzes the benefits different reinforcement systems of composite materials provide, with the aim of contributing to the knowledge of this technique for recovering or increasing the strength properties of timber elements subjected to bending loads. It is a study based on data obtained experimentally using bending tests of pine timber beams reinforced with composite materials. Fibers used for the execution of the reinforcement are basalt and carbon. Basalt fiber composites are applied in different grammages, whereas with carbon composites, unidirectional and bidirectional fabrics are used. The behavior of the beams was analyzed regarding the reinforcement variables applied, and the results are compared with those of the tested beams without reinforcement. Furthermore it has been proved adjunting the nonlinear calculation model applied to predict the failure load of each reinforced beam. This work proves the good behavior of fiber reinforce plastic (FRP) with basalt fiber when applied to timber beams, and that of bidirectional carbon fabrics as opposed to the unidirectional ones.

Agricultural use of organic wastes as source of nitrogen and phosphorus: risks and opportunities

El nitrógeno (N) y el fósforo (P) son nutrientes esenciales en la producción de cultivos. El desarrollo de los fertilizantes de síntesis durante el siglo XX permitió una intensificación de la agricultura y un aumento de las producciones pero a su vez el gran input de nutrientes ha resultado en algunos casos en sistemas poco eficientes incrementando las pérdidas de estos nutrientes al medio ambiente. En el caso del P, este problema se agrava debido a la escasez de reservas de roca fosfórica necesaria para la fabricación de fertilizantes fosfatados. La utilización de residuos orgánicos en agricultura como fuente de N y P es una buena opción de manejo que permite valorizar la gran cantidad de residuos que se generan. Sin embargo, es importante conocer los procesos que se producen en el suelo tras la aplicación de los mismos, ya que influyen en la disponibilidad de nutrientes que pueden ser utilizados por el cultivo así como en las pérdidas de nutrientes de los agrosistemas que pueden ocasionar problemas de contaminación. Aunque la dinámica del N en el suelo ha sido más estudiada que la del P, los problemas importantes de contaminación por nitratos en zonas vulnerables hacen necesaria la evaluación de aquellas prácticas de manejo que pudieran agravar esta situación, y en el caso de los residuos orgánicos, la evaluación de la respuesta agronómica y medioambiental de la aplicación de materiales con un alto contenido en N (como los residuos procedentes de la industria vinícola y alcoholera). En cuanto al P, debido a la mayor complejidad de su ciclo y de las reacciones que ocurren en el suelo, hay un mayor desconocimiento de los factores que influyen en su dinámica en los sistemas suelo-planta, lo que supone nuevas oportunidades de estudio en la evaluación del uso agrícola de los residuos orgánicos. Teniendo en cuenta los conocimientos previos sobre cada nutriente así como las necesidades específicas en el estudio de los mismos, en esta Tesis se han evaluado: (1) el efecto de la aplicación de residuos procedentes de la industria vinícola y alcoholera en la dinámica del N desde el punto de vista agronómico y medioambiental en una zona vulnerable a la contaminación por nitratos; y (2) los factores que influyen en la disponibilidad de P en el suelo tras la aplicación de residuos orgánicos. Para ello se han llevado a cabo incubaciones de laboratorio así como ensayos de campo que permitieran evaluar la dinámica de estos nutrientes en condiciones reales. Las incubaciones de suelo en condiciones controladas de humedad y temperatura para determinar el N mineralizado se utilizan habitualmente para estimar la disponibilidad de N para el cultivo así como el riesgo medioambiental. Por ello se llevó a cabo una incubación en laboratorio para conocer la velocidad de mineralización de N de un compost obtenido a partir de residuos de la industria vinícola y alcoholera, ampliamente distribuida en Castilla-La Mancha, región con problemas importantes de contaminación de acuíferos por nitratos. Se probaron tres dosis crecientes de compost correspondientes a 230, 460 y 690 kg de N total por hectárea que se mezclaron con un suelo franco arcillo arenoso de la zona. La evolución del N mineral en el suelo a lo largo del tiempo se ajustó a un modelo de regresión no lineal, obteniendo valores bajos de N potencialmente mineralizable y bajas contantes de mineralización, lo que indica que se trata de un material resistente a la mineralización y con una lenta liberación de N en el suelo, mineralizándose tan solo 1.61, 1.33 y 1.21% del N total aplicado con cada dosis creciente de compost (para un periodo de seis meses). Por otra parte, la mineralización de N tras la aplicación de este material también se evaluó en condiciones de campo, mediante la elaboración de un balance de N durante dos ciclos de cultivo (2011 y 2012) de melón bajo riego por goteo, cultivo y manejo agrícola muy característicos de la zona de estudio. Las constantes de mineralización obtenidas en el laboratorio se ajustaron a las temperaturas reales en campo para predecir el N mineralizado en campo durante el ciclo de cultivo del melón, sin embargo este modelo generalmente sobreestimaba el N mineralizado observado en campo, por la influencia de otros factores no tenidos en cuenta para obtener esta predicción, como el N acumulado en el suelo, el efecto de la planta o las fluctuaciones de temperatura y humedad. Tanto el ajuste de los datos del laboratorio al modelo de mineralización como las predicciones del mismo fueron mejores cuando se consideraba el efecto de la mezcla suelo-compost que cuando se aislaba el N mineralizado del compost, mostrando la importancia del efecto del suelo en la mineralización del N procedente de residuos orgánicos. Dado que esta zona de estudio ha sido declarada vulnerable a la contaminación por nitratos y cuenta con diferentes unidades hidrológicas protegidas, en el mismo ensayo de campo con melón bajo riego por goteo se evaluó el riesgo de contaminación por nitratos tras la aplicación de diferentes dosis de compost bajo dos regímenes de riego, riego ajustado a las necesidades del cultivo (90 ó 100% de la evapotranspiración del cultivo (ETc)) o riego excedentario (120% ETc). A lo largo del ciclo de cultivo se estimó semanalmente el drenaje mediante la realización de un balance hídrico, así como se tomaron muestras de la solución de suelo y se determinó su concentración de nitratos. Para evaluar el riesgo de contaminación de las aguas subterráneas asociado con estas prácticas, se utilizaron algunos índices medioambientales para determinar la variación en la calidad del agua potable (Índice de Impacto (II)) y en la concentración de nitratos del acuífero (Índice de Impacto Ambiental (EII)). Para combinar parámetros medioambientales con parámetros de producción, se calculó la eficiencia de manejo. Se observó que la aplicación de compost bajo un régimen de riego ajustado no aumentaba el riesgo de contaminación de las aguas subterráneas incluso con la aplicación de la dosis más alta. Sin embargo, la aplicación de grandes cantidades de compost combinada con un riego excedentario supuso un incremento en el N lixiviado a lo largo del ciclo de cultivo, mientras que no se obtuvieron mayores producciones con respecto al riego ajustado. La aplicación de residuos de la industria vinícola y alcoholera como fuente de P fue evaluada en suelos calizos caracterizados por una alta capacidad de retención de P, lo cual en algunos casos limita la disponibilidad de este nutriente. Para ello se llevó a cabo otro ensayo de incubación con dos suelos de diferente textura, con diferente contenido de carbonato cálcico, hierro y con dos niveles de P disponible; a los que se aplicaron diferentes materiales procedentes de estas industrias (con y sin compostaje previo) aportando diferentes cantidades de P. A lo largo del tiempo se analizó el P disponible del suelo (P Olsen) así como el pH y el carbono orgánico disuelto. Al final de la incubación, con el fin de estudiar los cambios producidos por los diferentes residuos en el estado del P del suelo se llevó a cabo un fraccionamiento del P inorgánico del suelo, el cual se separó en P soluble y débilmente enlazado (NaOH-NaCl-P), P soluble en reductores u ocluido en los óxidos de Fe (CBD-P) y P poco soluble precipitado como Ca-P (HCl-P); y se determinó la capacidad de retención de P así como el grado de saturación de este elemento en el suelo. En este ensayo se observó que, dada la naturaleza caliza de los suelos, la influencia de la cantidad de P aplicado con los residuos en el P disponible sólo se producía al comienzo del periodo de incubación, mientras que al final del ensayo el incremento en el P disponible del suelo se igualaba independientemente del P aplicado con cada residuo, aumentando el P retenido en la fracción menos soluble con el aumento del P aplicado. Por el contrario, la aplicación de materiales orgánicos menos estabilizados y con un menor contenido en P, produjo un aumento en las formas de P más lábiles debido a una disolución del P retenido en la fracción menos lábil, lo cual demostró la influencia de la materia orgánica en los procesos que controlan el P disponible en el suelo. La aplicación de residuos aumentó el grado de saturación de P de los suelos, sin embargo los valores obtenidos no superaron los límites establecidos que indican un riesgo de contaminación de las aguas. La influencia de la aplicación de residuos orgánicos en las formas de P inorgánico y orgánico del suelo se estudió además en un suelo ácido de textura areno francosa tras la aplicación en campo a largo plazo de estiércol vacuno y de compost obtenido a partir de biorresiduos, así como la aplicación combinada de compost y un fertilizante mineral (superfosfato tripe), en una rotación de cultivos. En muestras de suelo recogidas 14 años después del establecimiento del experimento en campo, se determinó el P soluble y disponible, la capacidad de adsorción de P, el grado de saturación de P así como diferentes actividades enzimáticas (actividad deshidrogenasa, fosfatasa ácida y fosfatasa alcalina). Las diferentes formas de P orgánico en el suelo se estudiaron mediante una técnica de adición de enzimas con diferentes substratos específicos a extractos de suelo de NaOH-EDTA, midiendo el P hidrolizado durante un periodo de incubación por colorimetría. Las enzimas utilizadas fueron la fosfatasa ácida, la nucleasa y la fitasa las cuales permitieron identificar monoésteres hidrolizables (monoester-like P), diésteres (DNA-like P) e inositol hexaquifosfato (Ins6P-like P). La aplicación a largo plazo de residuos orgánicos aumentó el P disponible del suelo proporcionalmente al P aplicado con cada tipo de fertilización, suponiendo un mayor riesgo de pérdidas de P dado el alto grado de saturación de este suelo. La aplicación de residuos orgánicos aumentó el P orgánico del suelo resistente a la hidrólisis enzimática, sin embargo no influyó en las diferentes formas de P hidrolizable por las enzimas en comparación con las observadas en el suelo sin enmendar. Además, las diferentes formas de P orgánico aplicadas con los residuos orgánicos no se correspondieron con las analizadas en el suelo lo cual demostró que éstas son el resultado de diferentes procesos en el suelo mediados por las plantas, los microorganismos u otros procesos abióticos. En este estudio se encontró una correlación entre el Ins6P-like P y la actividad microbiana (actividad deshidrogenasa) del suelo, lo cual refuerza esta afirmación. Por último, la aplicación de residuos orgánicos como fuente de N y P en la agricultura se evaluó agronómicamente en un escenario real. Se estableció un experimento de campo para evaluar el compost procedente de residuos de bodegas y alcoholeras en el mismo cultivo de melón utilizado en el estudio de la mineralización y lixiviación de N. En este experimento se estudió la aplicación de tres dosis de compost: 1, 2 y 3 kg de compost por metro lineal de plantación correspondientes a 7, 13 y 20 t de compost por hectárea respectivamente; y se estudió el efecto sobre el crecimiento de las plantas, la acumulación de N y P en la planta, así como la producción y calidad del cultivo. La aplicación del compost produjo un ligero incremento en la biomasa vegetal acompañado por una mejora significativa de la producción con respecto a las parcelas no enmendadas, obteniéndose la máxima producción con la aplicación de 2 kg de compost por metro lineal. Aunque los efectos potenciales del N y P fueron parcialmente enmascarados por otras entradas de estos nutrientes en el sistema (alta concentración de nitratos en el agua de riego y ácido fosfórico suministrado por fertirrigación), se observó una mayor acumulación de P uno de los años de estudio que resultó en un aumento en el número de frutos en las parcelas enmendadas. Además, la mayor acumulación de N y P disponible en el suelo al final del ciclo de cultivo indicó el potencial uso de estos materiales como fuente de estos nutrientes. ABSTRACT Nitrogen (N) and phosphorus (P) are essential nutrients in crop production. The development of synthetic fertilizers during the 20th century allowed an intensification of the agriculture increasing crop yields but in turn the great input of nutrients has resulted in some cases in inefficient systems with higher losses to the environment. Regarding P, the scarcity of phosphate rock reserves necessary for the production of phosphate fertilizers aggravates this problem. The use of organic wastes in agriculture as a source of N and P is a good option of management that allows to value the large amount of wastes generated. However, it is important to understand the processes occurring in the soil after application of these materials, as they affect the availability of nutrients that can be used by the crop and the nutrient losses from agricultural systems that can cause problems of contamination. Although soil N dynamic has been more studied than P, the important concern of nitrate pollution in Nitrate Vulnerable Zones requires the evaluation of those management practices that could aggravate this situation, and in the case of organic wastes, the evaluation of the agronomic and environmental response after application of materials with a high N content (such as wastes from winery and distillery industries). On the other hand, due to the complexity of soil P cycle and the reactions that occur in soil, there is less knowledge about the factors that can influence its dynamics in the soil-plant system, which means new opportunities of study regarding the evaluation of the agricultural use of organic wastes. Taking into account the previous knowledge of each nutrient and the specific needs of study, in this Thesis we have evaluated: (1) the effect of the application of wastes from the winery and distillery industries on N dynamics from the agronomic and environmental viewpoint in a vulnerable zone; and (2) the factors that influence P availability in soils after the application of organic wastes. With this purposes, incubations were carried out in laboratory conditions as well as field trials that allow to assess the dynamic of these nutrients in real conditions. Soil incubations under controlled moisture and temperature conditions to determine N mineralization are commonly used to estimate N availability for crops together with the environmental risk. Therefore, a laboratory incubation was conducted in order to determine the N mineralization rate of a compost made from wastes generated in the winery and distillery industries, widely distributed in Castilla-La Mancha, a region with significant problems of aquifers contamination by nitrates. Three increasing doses of compost corresponding to 230, 460 and 690 kg of total N per hectare were mixed with a sandy clay loam soil collected in this area. The evolution of mineral N in soil over time was adjusted to a nonlinear regression model, obtaining low values of potentially mineralizable N and low constants of mineralization, indicating that it is a material resistant to mineralization with a slow release of N, with only 1.61, 1.33 and 1.21% of total N applied being mineralized with each increasing dose of compost (for a period of six months). Furthermore, N mineralization after the application of this material was also evaluated in field conditions by carrying out a N balance during two growing seasons (2011 and 2012) of a melon crop under drip irrigation, a crop and management very characteristic of the area of study. The mineralization constants obtained in the laboratory were adjusted to the actual temperatures observed in the field to predict N mineralized during each growing season, however, this model generally overestimated the N mineralization observed in the field, because of the influence of other factors not taken into account for this prediction, as N accumulated in soil, the plant effect or the fluctuations of temperature and moisture. The fitting of the laboratory data to the model as well as the predictions of N mineralized in the field were better when considering N mineralized from the soil-compost mixture rather than when N mineralized from compost was isolated, underlining the important role of the soil on N mineralization from organic wastes. Since the area of study was declared vulnerable to nitrate pollution and is situated between different protected hydrological units, the risk of nitrate pollution after application of different doses compost was evaluated in the same field trial with melon under two irrigation regimes, irrigation adjusted to the crop needs (90 or 100% of the crop evapotranspiration (ETc)) or excedentary irrigation (120% ETc). Drainage was estimated weekly throughout the growing season by conducting a water balance, samples of the soil solution were taken and the concentration of nitrates was determined. To assess the risk of groundwater contamination associated with these practices, some environmental indices were used to determine the variation in the quality of drinking water (Impact Index (II)) and the nitrates concentration in the groundwater (Environmental Impact Index (EII)). To combine environmental parameters together with yield parameters, the Management Efficiency was calculated. It was observed that the application of compost under irrigation adjusted to the plant needs did not represent a higher risk of groundwater contamination even with the application of the highest doses. However, the application of large amounts of compost combined with an irrigation surplus represented an increase of N leaching during the growing season compared with the unamended plots, while no additional yield with respect to the adjusted irrigation strategy is obtained. The application of wastes derived from the winery and distillery industry as source of P was evaluated in calcareous soils characterized by a high P retention capacity, which in some cases limits the availability of this nutrient. Another incubation experiment was carried out using two soils with different texture, different calcium carbonate and iron contents and two levels of available P; to which different materials from these industries (with and without composting) were applied providing different amounts of P. Soil available P (Olsen P), pH and dissolved organic carbon were analyzed along time. At the end of the incubation, in order to study the changes in soil P status caused by the different residues, a fractionation of soil inorganic P was carried out, which was separated into soluble and weakly bound P (NaOH-NaCl- P), reductant soluble P or occluded in Fe oxides (CBD-P) and P precipitated as poorly soluble Ca-P (HCl-P); and the P retention capacity and degree of P saturation were determined as well. Given the calcareous nature of the soils, the influence of the amount of P applied with the organic wastes in soil available P only occurred at the beginning of the incubation period, while at the end of the trial the increase in soil available P equalled independently of the amount of P applied with each residue, increasing the P retained in the least soluble fraction when increasing P applied. Conversely, the application of less stabilized materials with a lower content of P resulted in an increase in the most labile P forms due to dissolution of P retained in the less labile fraction, demonstrating the influence of organic matter addition on soil P processes that control P availability in soil. As expected, the application of organic wastes increased the degree of P saturation in the soils, however the values obtained did not exceed the limits considered to pose a risk of water pollution. The influence of the application of organic wastes on inorganic and organic soil P forms was also studied in an acid loamy sand soil after long-term field application of cattle manure and biowaste compost and the combined application of compost and mineral fertilizer (triple superphosphate) in a crop rotation. Soil samples were collected 14 years after the establishment of the field experiment, and analyzed for soluble and available P, P sorption capacity, degree of P saturation and enzymatic activities (dehydrogenase, acid phosphatase and alkaline phosphatase). The different forms of organic P in soil were determined by using an enzyme addition technique, based on adding enzymes with different substrate specificities to NaOH-EDTA soil extracts, measuring the hydrolyzed P colorimetrically after an incubation period. The enzymes used were acid phosphatase, nuclease and phytase which allowed to identify hydrolyzable monoesters (monoester-like P) diesters (DNA-like P) and inositol hexakisphosphate (Ins6P-like P). The long-term application of organic wastes increased soil available P proportionally to the P applied with each type of fertilizer, assuming a higher risk of P losses given the high degree of P saturation of this soil. The application of organic wastes increased soil organic P resistant to enzymatic hydrolysis, but no influence was observed regarding the different forms of enzyme hydrolyzable organic P compared to those observed in the non-amended soil. Furthermore, the different forms of organic P applied with the organic wastes did not correspond to those analyzed in the soil which showed that these forms in soil are a result of multifaceted P turnover processes in soil affected by plants, microorganisms and abiotic factors. In this study, a correlation between Ins6P-like P and the microbial activity (dehydrogenase activity) of soil was found, which reinforces this claim. Finally, the application of organic wastes as a source of N and P in agriculture was evaluated agronomically in a real field scenario. A field experiment was established to evaluate the application of compost made from wine-distillery wastes in the same melon crop used in the experiments of N mineralization and leaching. In this experiment the application of three doses of compost were studied: 1 , 2 and 3 kg of compost per linear meter of plantation corresponding to 7, 13 and 20 tonnes of compost per hectare respectively; and the effect on plant growth, N and P accumulation in the plant as well as crop yield and quality was studied. The application of compost produced a slight increase in plant biomass accompanied by a significant improvement in crop yield with respect to the unamended plots, obtaining the maximum yield with the application of 2 kg of compost per linear meter. Although the potential effects of N and P were partially masked by other inputs of these nutrients in the system (high concentration of nitrates in the irrigation water and phosphoric acid supplied by fertigation), an effect of P was observed the first year of study resulting in a greater plant P accumulation and in an increase in the number of fruits in the amended plots. In addition, the higher accumulation of available N and P in the topsoil at the end of the growing season indicated the potential use of this material as source of these nutrients.

Estudio de la respuesta dinámica transversal de viaductos altos de líneas de ferrocarril de alta velocidad bajo la acción de cargas de uso

Es conocido que las dimensiones de los puentes de ferrocarril han ido cambiando debido a las estrictas condiciones de trazado impuestas en las líneas de alta velocidad. Además, la creciente preocupación de la sociedad por cuidar y proteger el medio ambiente, reflejado en la correspondiente normativa, ha generado nuevos condicionantes en el diseño de estas infraestructuras. En concreto, se ha limitado el movimiento de grandes volúmenes de terreno particularmente en los espacios protegidos. Por estas razones, hoy en día se proyectan y construyen puentes de ferrocarril más altos y más largos en todo el mundo. En España se han construido varios viaductos de pilas altas para líneas de alta velocidad. Ejemplos de estas infraestructuras son el Viaducto O’Eixo y el Viaducto de Barbantiño, situados en la línea de alta velocidad Madrid-Galicia, Estos viaductos altos se caracterizan por tener una mayor flexibilidad lateral y una frecuencia fundamental de oscilación baja, de hasta 0.2 Hz. La respuesta dinámica de este tipo de estructura puede aumentar como consecuencia de la aproximación entre la frecuencias propias de la misma y las de excitación debidas al paso del tren y a la acción del viento. Por lo tanto, estas estructuras pueden presentar problemas a la hora de cumplir con las limitaciones impuestas en las normas de diseño de puentes de ferrocarril, y otras, para garantizar la seguridad del tráfico y el confort de los viajeros. La respuesta dinámica lateral de viaductos de pilas altas no ha sido suficientemente estudiada en la literatura científica. Se pueden intuir varios de los motivos para explicar esta carencia. El primero es la relativamente reciente aparición de este tipo de viaductos asociados al desarrollo de la alta velocidad. Por otro lado, se hace necesario, para estudiar este tema, construir nuevos modelos numéricos adecuados para el estudio de la interacción dinámica lateral del puente y del tren. La interacción entre el puente y un tren viajando sobre él es un problema dinámico no lineal, dependiente del tiempo y de acoplamiento entre los dos subsistemas que intervienen (vehículo y puente). Los dos subsistemas, que pueden ser modelados como estructuras elásticas, interaccionan el uno con el otro a través de las fuerzas de contacto, que tiene una marcada naturaleza no lineal por el rozamiento entre rueda y carril, y por la geometría de los perfiles de estos dos elementos en contacto. En esta tesis, se desarrolla la formulación completa de un modelo no lineal de interacción tren-vía-puente-viento que reproduce adecuadamente las fuerzas laterales de contacto rueda-carril, fuerzas que van a tener una gran influencia en los índices de seguridad del tráfico. Este modelo se ha validado a partir de casos resueltos en la literatura científica, y de medidas experimentales tomadas en eventos dinámicos ocurridos en los viaductos de Arroyo de Valle y Arroyo de las Piedras. Puentes altos que han estado monitorizados en servicio durante dos años. En los estudios realizados en este trabajo, se cuantifican, empleando el modelo construido, los niveles de seguridad del tráfico y de confort de los pasajeros de trenes ligeros de alta velocidad, como el tren articulado AVE S-100, que viajan sobre viaductos altos sometidos, o no, a fuertes vientos laterales racheados. Finalmente, se ha obtenido el grado de mejora de la seguridad del tráfico y del confort de los viajeros, cuando se emplean pantallas anti-viento en el tablero y amortiguadores de masa sintonizados en la cabeza de las pilas de un viaducto alto. Resultando, el uso simultaneo de estos dos dispositivos (pantallas y amortiguadores de masa), en puentes altos de líneas de alta velocidad, una opción a considerar en la construcción de estas estructuras para elevar significativamente el nivel de servicio de las mismas. It is known that dimensions of railway bridges have been changing due to the strict high-speed lines layout parameters. Moreover, the growing concern of society to take care of and protect the environment, reflected in the corresponding regulations, has created new environment requirements for the design of these infrastructures. Particularly, the mentioned regulations do not allow designers to move far from terrain to build these railway lines. Due to all these reasons, longer and higher railway bridges are being designed and built around the world. In Spain, several high pier railway viaducts have been built for high speed lines. Barbantiño Viaduct and Eixo Viaduct, belonging to the Madrid-Galicia high speed line, are examples of this kind of structures. These high viaducts have great lateral flexibility and a low fundamental vibration frequency of down to 0.2 Hz. The dynamic response of high speed railway bridges may increase because of the approximation between the natural viaduct frequencies and the excitation ones due to the train travel and the wind action. Therefore, this bridge response could not satisfy the serviceability limits states, for traffic safety and for passenger comfort, considered by the design standards of high speed bridges. It is difficult to find papers in the scientific literature about the lateral response of high-speed trains travel over long viaducts with high piers. Several reasons could explain this issue. On one hand, the construction of this kind of viaduct is relatively recent and it is associated to the development of the high speed railway. On the other hand, in order to study the dynamic lateral interaction between the train and the high bridge, it is necessary to build new numerical and complex models. The interaction between the bridge-track subsystem and the vehicle subsystem travelling over the bridge is a coupling, nonlinear and time dependent problem. Both subsystems, train and bridge, which can be modelled as elastic structures, interact each other through the contact forces. These forces have a strong nonlinear nature due to the friction and the geometry of rail and wheel profiles. In this thesis, the full formulation of a train-track-bridge-wind nonlinear interaction model is developed. This model can reproduce properly the lateral contact wheel-rail forces, which have a great influence on traffic safety indices. The validation of the model built has been reached through interaction solved cases found in the scientific literature and experimental measures taken in dynamic events which happened at Arroyo de las Piedras and Arroyo del Valle Viaducts. These high bridges have been controlled during two years of service by means of structural health monitoring. In the studies carried out for this thesis, the levels of traffic safety and passenger comfort are quantified using the interaction model built, in the cases of high speed and light trains, as AVE S-100, travelling over high pier bridges and with or without lateral turbulent winds acting. Finally, the improvement rate of the traffic safety and passenger comfort has been obtained, when wind barriers are used at the bridge deck and tuned mass dampers are installed at the pier heads of a high viaduct. The installation of both devices, wind barriers and tuned mass damper, at the same time, turned out to be a good option to be considered in the design of high pier railway viaducts, to improve significantly the serviceability level of this kind of structures.

Atenuação de vibrações em pás de helicópteros utilizando circuito piezelétrico semi-passivo

O uso de materiais inteligentes em problemas de controle de vibração tem sido investigado em diversas pesquisas ao longo dos últimos anos. Apesar de que diferentes materiais inteligentes estão disponíveis, o piezelétrico tem recebido grande atenção devido à facilidade de uso como sensores, atuadores, ou ambos simultaneamente. As principais técnicas de controle usando materiais piezoelétricos são os ativos e passivos. Circuitos piezelétricos passivos são ajustados para uma frequência específica e, portanto, a largura de banda efetiva é pequena. Embora os sistemas ativos possam apresentar um bom desempenho no controle de vibração, a quantidade de energia externa e hardware adicionado são questões importantes. As técnicas SSD (Synchronized Switch Damping) foram desenvolvidas como uma alternativa aos controladores passivos e controladores ativos de vibração. Elas podem ser técnicas semi-ativas ou semi-passivas que introduzem um tratamento não linear na tensão elétrica proveniente do material piezelétrico e induz um aumento na conversão de energia mecânica para energia elétrica e, consequentemente, um aumento no efeito de amortecimento. Neste trabalho, o controle piezoelétrico semi-passivo de uma pá piezelétrica engastada é apresentado e comparado com outros controladores. O modelo não linear electromecânico de uma pá com piezocerâmicas incorporados é determinado com base no método variacional-assintótico (VAM). O sistema rotativo acoplado não linear é resolvido no domínio do tempo, utilizando um método de integração alfa-generalizado afim de garantir a estabilidade numérica. As simulações são realizadas para uma vasta gama de velocidades de rotação. Em primeiro lugar, um conjunto de resistências (variando desde a condição de curto-circuito para a condição de circuito aberto) é considerada. O efeito da resistência ótima (que resulta em máximo amortecimento) sobre o comportamento do sistema é investigado para o aumento da velocidade de rotação. Mais tarde, a técnica SSDS é utilizada para amortecer as oscilações da pá com o aumento da velocidade de rotação. Os resultados mostram que a técnica SSDS pode ser um método útil para o controle de vibrações de vigas rotativas não lineares, tais como pás de helicóptero.

Excitation spectra of the spin-1/2 triangular-lattice Heisenberg antiferromagnet

We use series expansion methods to calculate the dispersion relation of the one-magnon excitations for the spin-(1)/(2) triangular-lattice nearest-neighbor Heisenberg antiferromagnet above a three-sublattice ordered ground state. Several striking features are observed compared to the classical (large-S) spin-wave spectra. Whereas, at low energies the dispersion is only weakly renormalized by quantum fluctuations, significant anomalies are observed at high energies. In particular, we find rotonlike minima at special wave vectors and strong downward renormalization in large parts of the Brillouin zone, leading to very flat or dispersionless modes. We present detailed comparison of our calculated excitation energies in the Brillouin zone with the spin-wave dispersion to order 1/S calculated recently by Starykh, Chubukov, and Abanov [Phys. Rev. B74, 180403(R) (2006)]. We find many common features but also some quantitative and qualitative differences. We show that at temperatures as low as 0.1J the thermally excited rotons make a significant contribution to the entropy. Consequently, unlike for the square lattice model, a nonlinear sigma model description of the finite-temperature properties is only applicable at temperatures < 0.1J. Finally, we review recent NMR measurements on the organic compound kappa-(BEDT-TTF)(2)Cu-2(CN)(3). We argue that these are inconsistent with long-range order and a description of the low-energy excitations in terms of interacting magnons, and that therefore a Heisenberg model with only nearest-neighbor exchange does not offer an adequate description of this material.

Parameter Identification of a Fed-Batch Cultivation of S. Cerevisiae using Genetic Algorithms

Fermentation processes as objects of modelling and high-quality control are characterized with interdependence and time-varying of process variables that lead to non-linear models with a very complex structure. This is why the conventional optimization methods cannot lead to a satisfied solution. As an alternative, genetic algorithms, like the stochastic global optimization method, can be applied to overcome these limitations. The application of genetic algorithms is a precondition for robustness and reaching of a global minimum that makes them eligible and more workable for parameter identification of fermentation models. Different types of genetic algorithms, namely simple, modified and multi-population ones, have been applied and compared for estimation of nonlinear dynamic model parameters of fed-batch cultivation of S. cerevisiae.