Relação entre força muscular e função motora em pacientes com distrofia muscular de Duchenne: acompanhamento de quatro anos

OBJETIVO: Investigar a relação entre força muscular e função motora, em pacientes com DMD, em um período de 4 anos consecutivos, a partir de avaliações semestrais. MÉTODO: A força muscular foi medida por meio de testes manuais e o cálculo por grupo muscular seguiu o proposto pelo Medical Research Council (MRC) e a função motora pelo método de Medida da Função Motora (MFM), em 43 pacientes (8-30 anos). Foi realizada uma análise descritiva e o teste de correlação de Spearman. Foram investigadas as relações entre pontuações totais e parciais da MRC e da MFM. RESULTADOS: O estudo evidenciou correlações classificadas de moderada a forte relação entre a força muscular e função motora, principalmente com o escore total da MFM e a dimensão D2 (musculatura axial e função motora proximal). Foi encontrada relação negativa moderada entre idade e essas variáveis. CONCLUSÃO: A perda progressiva da função motora tem relação direta e proporcional com a diminuição da força muscular. Quanto maior a idade do paciente, pior sua função motora e força muscular, fornecendo com essa informação, indicadores adicionais da progressão da doença

The comparison of maximal and endurance strength of quadriceps femori in trained and untrained elderly

The purpose of this study was to examine the differences in knee extensor maximal and endurance strength in elderly. Sixteen healthy elderly served as subjects, eight of them trained , age 61.0±8.9 yrs; height, 170.6±6.8 cm; weight, 71.8±11.7 kg [mean ± standard deviation] and eight untrained 61.4±8.1 yrs, height 174.6±7.4 cm; weight 83.9 ±14.2 kg. Maximal strength in single leg extension exercise was measured unilaterally with the dominant leg until the subjects reached their 1 Repetition Maximum (RM) covering the full Range of Motion (ROM). Muscular endurance was obtained with a load of 75% of 1-RM for 3 consecutive sets, with 2 min rest periods till failure. Load at 1 RM was lower in absolute terms in untrained, but not significant, while the relative 1-RM test was significantly lower in untrained subjects (0.20 vs. 0.25 kg load/kg body weight) (p<0.05). The number of repetitions and amount of weight lifted performed of all 3 sets was higher in trained subjects, but not significant. In the trained group both repetitions and the load managed in the third set was significant lower compared with the first two sets. The result that maximal force output is more affected compared to muscular endurance in these subjects might be due to the habitual use of quadriceps femoris muscles during activity of daily living in both trained and untrained elderly.

Correlação entre força muscular do assoalho pélvico, função sexual e qualidade de vida em mulheres de meia idade

Introduction: Menopause is characterized by the depletion of ovarian follicles and the gradual decline in estradiol levels, which ends with the definitive cessation of menstrual periods (menopause). As a result of hypoestrogenism, characteristic symptoms, such as hot flashes, night sweats, vaginal dryness, dyspareunia, insomnia, mood swings and depression can be observed. There is also the weakening of the pelvic floor muscles (MAP) as a result of progressive muscle-aponeurotic and connective atrophy with consequent decreased sexual function. Objective: To evaluate the strength of MAP, sexual function and quality of life of menopausal women. Methodology: This is an observational, analytical, cross-sectional design. The sample consisted of 55 women (35 postmenopausal and 20 perimenopausal), aged between 40 and 65, who were assessed by muscle strength and perineometry test. For the assessment of sexual function and quality of life, used the Female Sexual Function Index (FSFI) and Utian Quality of Life (UQOL), respectively. Statistical analysis was performed using Pearson's correlation and multivariate analysis. Results: The mean age was 52.78 (± 6.47 years). Sexual dysfunction presented, 61.8% of participants (43.62% of postmenopausal and perimenopausal 18.17%). Muscle strength test and the maximum perineometry had a median of 3.00 (Q25: 2 e Q75: 4) and 33,50 cmH20 (Q25: 33,5 e Q75: 46,6), respectively. No correlation was found between sexual function and muscle strength (r = 0.035; p = 0.802) and between sexual function and perineometry (r = 0.126; p = 0.358). The mean total score of UQOL was 74.45 (± 12.23). Weak positive correlation was found between sexual function and quality of life (r = +0.422 p = 0.001). Multivariate analysis identified associations between sexual function and variables: quality of life, climacteric symptoms, physical activity and education level. Conclusions: These results suggest that the climacteric symptoms, quality of life, physical activity and level of education are associated with sexual function in menopausal women. However, the muscular component of sexual function needs to be further investigated in this context.

Efeito do treinamento muscular inspiratório com diferentes cargas na força e função de músculos respiratórios

Background: The inspiratory muscle training (IMT) has been considered an option in reversing or preventing decrease in respiratory muscle strength, however, little is known about the adaptations of these muscles arising from the training with charge. Objectives: To investigate the effect of IMT on the diaphragmatic muscle strength and function neural and structural adjustment of diaphragm in sedentary young people, compare the effects of low intensity IMT with moderate intensity IMT on the thickness, mobility and electrical activity of diaphragm and in inspiratory muscles strength and establish a protocol for conducting a systematic review to evaluate the effects of respiratory muscle training in children and adults with neuromuscular diseases. Materials and Methods: A randomized, double-blind, parallel-group, controlled trial, sample of 28 healthy, both sexes, and sedentary young people, divided into two groups: 14 in the low load training group (G10%) and 14 in the moderate load training group (G55%). The volunteers performed for 9 weeks a home IMT protocol with POWERbreathe®. The G55% trained with 55% of maximal inspiratory pressure (MIP) and the G10% used a charge of 10% of MIP. The training was conducted in sessions of 30 repetitions, twice a day, six days per week. Every two weeks was evaluated MIP and adjusted the load. Volunteers were submitted by ultrasound, surface electromyography, spirometry and manometer before and after IMT. Data were analyzed by SPSS 20.0. Were performed Student's t-test for paired samples to compare diaphragmatic thickness, MIP and MEP before and after IMT protocol and Wilcoxon to compare the RMS (root mean square) and median frequency (MedF) values also before and after training protocol. They were then performed the Student t test for independent samples to compare mobility and diaphragm thickness, MIP and MEP between two groups and the Mann-Whitney test to compare the RMS and MedF values also between the two groups. Parallel to experimental study, we developed a protocol with support from the Cochrane Collaboration on IMT in people with neuromuscular diseases. Results: There was, in both groups, increased inspiratory muscle strength (P <0.05) and expiratory in G10% (P = 0.009) increase in RMS and thickness of relaxed muscle in G55% (P = 0.005; P = 0.026) and there was no change in the MedF (P> 0.05). The comparison between two groups showed a difference in RMS (P = 0.04) and no difference in diaphragm thickness and diaphragm mobility and respiratory muscle strength. Conclusions: It was identified increased neural activity and diagrammatic structure with consequent increase in respiratory muscle strength after the IMT with moderate load. IMT with load of 10% of MIP cannot be considered as a placebo dose, it increases the inspiratory muscle strength and IMT with moderate intensity is able to enhance the recruitment of muscle fibers of diaphragm and promote their hypertrophy. The protocol for carrying out the systematic review published in The Cochrane Library.

Efeitos do Dynamic Tape na prevenção da sensação retardada de desconforto muscular no quadricípite

Projeto de Graduação apresentado à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Licenciado em Fisioterapia

Efeito do encurtamento muscular dos flexores da anca na actividade muscular dos extensores da anca, durante uma tarefa de agachamento, em jovens jogadores de futebol

Projeto de Graduação apresentado à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Licenciado em Fisioterapia

Efectos del tipo de recuperación sobre la oxigenación muscular durante el ejercicio de sentadilla

El objetivo de esta investigación es comprobar los cambios en la oxigenación muscular del recto anterior durante la realización del ejercicio de sentadilla según el tipo de recuperación. Para ello, 11 sujetos varones bien entrenados fueron distribuidos aleatoriamente a tres grupos experimentales: grupo que realiza recuperación pasiva con 2 minutos de descanso (GC), grupo que realiza recuperación activa hasta la estabilización de oxígeno (GA), grupo que realiza recuperación pasiva hasta la estabilización de oxígeno (GP). Todos realizaron la sentadilla hasta los 90º al 65% del 1RM con un 80% del carácter del esfuerzo (CE) (4x10). Los resultados muestran que el tiempo de reoxigenación (TrecSmO2) fue inferior significativamente en GA (77,94 ± 11,08) que en GC (p<0.001). En las inclinaciones medias de ejecución y reoxigenación el GA obtuvo los menores y mayores valores respectivamente y de forma significativa respecto a GC (p<0.001). Estas dos variables obtuvieron una relación inversamente proporcional con una r=-0.9585 (p<0.001). Estos resultados muestran una mejor reoxigenación en el grupo que realizó descanso de forma activa. Se muestra una relación inversamente proporcional entre la inclinaciones de ejecución y recuperación por lo que cuanto más rápida y completa sea la desoxigenación más lenta resultará la reoxigenación. Además, la saturación de oxígeno puede ser un factor de la fatiga neuromuscular y su control durante el entrenamiento de fuerza podría facilitar los objetivos de entrenamiento. Estos resultados muestran, a priori, una mejor recuperación entre series a nivel oxidativo cuando los sujetos realizan una recuperación de forma activa, en comparación con la pasiva.

Effect Of Simulated Microwave Disinfection On The Linear Dimensional Change, Hardness And Impact Strength Of Acrylic Resins Processed By Different Polymerizing Cycles.

This study investigated the effect of simulated microwave disinfection (SMD) on the linear dimensional changes, hardness and impact strength of acrylic resins under different polymerization cycles. Metal dies with referential points were embedded in flasks with dental stone. Samples of Classico and Vipi acrylic resins were made following the manufacturers' recommendations. The assessed polymerization cycles were: A-- water bath at 74ºC for 9 h; B-- water bath at 74ºC for 8 h and temperature increased to 100ºC for 1 h; C-- water bath at 74ºC for 2 h and temperature increased to 100ºC for 1 h;; and D-- water bath at 120ºC and pressure of 60 pounds. Linear dimensional distances in length and width were measured after SMD and water storage at 37ºC for 7 and 30 days using an optical microscope. SMD was carried out with the samples immersed in 150 mL of water in an oven (650 W for 3 min). A load of 25 gf for 10 sec was used in the hardness test. Charpy impact test was performed with 40 kpcm. Data were submitted to ANOVA and Tukey's test (5%). The Classico resin was dimensionally steady in length in the A and D cycles for all periods, while the Vipi resin was steady in the A, B and C cycles for all periods. The Classico resin was dimensionally steady in width in the C and D cycles for all periods, and the Vipi resin was steady in all cycles and periods. The hardness values for Classico resin were steady in all cycles and periods, while the Vipi resin was steady only in the C cycle for all periods. Impact strength values for Classico resin were steady in the A, C and D cycles for all periods, while Vipi resin was steady in all cycles and periods. SMD promoted different effects on the linear dimensional changes, hardness and impact strength of acrylic resins submitted to different polymerization cycles when after SMD and water storage were considered.

Effect Of Simulated Microwave Disinfection On The Linear Dimensional Change, Hardness And Impact Strength Of Acrylic Resins Processed By Different Polymerization Cycles.

This study investigated the effect of simulated microwave disinfection (SMD) on the linear dimensional changes, hardness and impact strength of acrylic resins under different polymerization cycles. Metal dies with referential points were embedded in flasks with dental stone. Samples of Classico and Vipi acrylic resins were made following the manufacturers' recommendations. The assessed polymerization cycles were: A) water bath at 74 ºC for 9 h; B) water bath at 74 ºC for 8 h and temperature increased to 100 ºC for 1 h; C) water bath at 74 ºC for 2 h and temperature increased to 100 ºC for 1 h; and D) water bath at 120 ºC and pressure of 60 pounds. Linear dimensional distances in length and width were measured after SMD and water storage at 37 ºC for 7 and 30 days using an optical microscope. SMD was carried out with the samples immersed in 150 mL of water in an oven (650 W for 3 min). A load of 25 gf for 10 s was used in the hardness test. Charpy impact test was performed with 40 kpcm. Data were submitted to ANOVA and Tukey's test (5%). The Classico resin was dimensionally steady in length in the A and D cycles for all periods, while the Vipi resin was steady in the A, B and C cycles for all periods. The Classico resin was dimensionally steady in width in the C and D cycles for all periods, and the Vipi resin was steady in all cycles and periods. The hardness values for Classico resin were steady in all cycles and periods, while the Vipi resin was steady only in the C cycle for all periods. Impact strength values for Classico resin were steady in the A, C and D cycles for all periods, while Vipi resin was steady in all cycles and periods. SMD promoted different effects on the linear dimensional changes, hardness and impact strength of acrylic resins submitted to different polymerization cycles when after SMD and water storage were considered.

Relationship Between Lower-limb Muscle Strength And Functional Independence Among Elderly People According To Frailty Criteria: A Cross-sectional Study.

Muscle strength and functional independence are considered to be determinants of frailty levels among elderly people. The aim here was to compare lower-limb muscle strength (LLMS) with functional independence in relation to sex, age and number of frailty criteria, and to ascertain the influence of these variables on elderly outpatients' independence. Quantitative cross-sectional study, in a tertiary hospital. The study was conducted on 150 elderly outpatients of both sexes who were in a cognitive condition allowing oral communication, between October 2005 and October 2007. The following instruments were used: five-times sit-to-stand test (FTSST), Functional Independence Measurement (FIM) and Lawton's Instrumental Activities of Daily Living Scale (IADL). Descriptive, comparative, multivariate, univariate and Cronbach alpha analyses were performed. The mean time taken in the FTSST was 21.7 seconds; the mean score for FIM was 82.2 and for IADL was 21.2; 44.7% of the subjects presented 1-2 frailty criteria and 55.3% > 3 criteria. There was a significant association between LLMS and functional independence in relation to the number of frailty criteria, without homogeneity regarding sex and age. Functional independence showed significant influence from sex and LLMS. Elderly individuals with 1 or 2 frailty criteria presented greater independence in all FTSST scores. The subjects with higher LLMS presented better functional independence.

Microtensile Bond Strength Of Methacrylate And Silorane Resins To Enamel And Dentin.

The aim of this study was to evaluate the microtensile bond strength (µTBS) of two substrates (enamel and dentin) considering two study factors: type of composite resin [methacrylate-based (Filtek Supreme) or silorane-based (Filtek LS)] and aging time (24 h or 3 months). Twenty human molars were selected and divided into 2 groups (n=10) considering two dental substrates, enamel or dentin. The enamel and dentin of each tooth was divided into two halves separated by a glass plate. Each tooth was restored using both tested composite resins following the manufacturer's instructions. The samples were sectioned, producing 4 sticks for each composite resin. Half of them were tested after 24 h and half after 3 months. µTBS testing was carried out at 0.05 mm/s. Data were analyzed by three-way ANOVA and Tukey's HSD tests at α=0.05. Significant differences between composite resins and substrates were found (p<0.05), but no statistically significant difference was found for aging time and interactions among study factors. The methacrylate-based resin showed higher µTBS than the silorane-based resin. The µTBS for enamel was significantly higher than for dentin, irrespective of the composite resin and storage time. Three months of storage was not sufficient time to cause degradation of the bonding interaction of either of the composite resins to enamel and dentin.

Effect Of Composite Containing An Iodonium Salt On The Bond Strength Of Brackets To Bovine Enamel.

This study investigated the effect of the incorporation of an iodonium salt in experimental composites, on the bond strength of metallic brackets bonded to bovine teeth. Two hundred and seventy bovine teeth were embedded in self-curing acrylic resin and divided into 18 groups (n=15), according to the experimental composite with an iodonium salt at molar concentrations 0 (control), 0.5, or 1%; the light-activation times (8, 20 and 40 s); and the storage times (10 min or 24 h). Metallic brackets were fixed on the tooth surface using experimental composites. Photoactivation was performed with a quartz-tungsten-halogen light-curing unit curing unit for 8, 20 and 40 s. The specimens were stored in distilled water at 37 °C for 10 min or 24 h and submitted to bond strength test at 0.5 mm/min. The data were subjected to three-way ANOVA and Tukey's test (α=0.05). The Adhesive Remnant Index (ARI) was used to classify the failure modes. The shear bond strengths (MPa) at 10 min for light-activation times of 8, 20 and 40 s were: G1 - 4.6, 6.9 and 7.1; G2 - 8.1, 9.2 and 9.9; G3 - 9.1, 10.4 and 10.7; and at 24 h were: G1 - 10.9, 11.1 and 11.7; G2 - 11.8, 12.7 and 14.2; G3 - 12.1, 14.4 and 15.8. There was a predominance of ARI score 3 for groups with 10 min storage time, and ARI score 2 for groups with 24 h storage time. In conclusion, the addition of iodonium salt (C05 and C1) to the experimental composite may increase the bond strength of brackets to bovine enamel using reduced light exposure times.

Dentin Bond Strength Of A Fluoride-releasing Adhesive System Submitted To Ph-cycling.

To evaluate the microtensile bond strength (µTBS) of a fluoride-containing adhesive system submitted to a pH-cycling and storage time regimen for primary outcomes. As secondary outcomes the fluoride released amount was evaluated. Twelve dentin surfaces from sound third molar were divided into 2 groups according to adhesive systems: Clearfil SE Protect (PB) and Clearfil SE Bond (SE). Sticks obtained (1.0 mm2) from teeth were randomly divided into 3 subgroups according to storage regimen model: immediate (24h); 5-month deionized water (W); and pH-cycling model (C). All sticks were tested for µTBS in a universal testing machine. Fluoride concentration was obtained from 1-4 days and 30-day in W and 1-4 days in demineralization (DE)/remineralization (RE) solutions from C, using a fluoride-specific electrode. µTBS and fluoride released data were, respectively, submitted to ANOVA in a split plot design and Tukey, and Friedman' tests (a=0.05). There was no significant interaction between adhesive system and storage regimen for µTBS. W showed the lowest µTBS values. There was no significant difference between 24 h and C models for µTBS. There was no significant difference between adhesive systems. Failure mode was predominantly cohesive within composite for the 24 h and W, for the C group it was mixed for SE and cohesive within composite for PB adhesive system. Fluoride concentrations in the DE/RE solutions were less than 0.03125 ppm and not detected in W. In conclusion, the fluoride-containing adhesive system performed similarly to the regular one. Hydrolytic degradation is the main problem with both adhesive systems, regardless of fluoride contents.

Undulatory Physical Resistance Training Program Increases Maximal Strength In Elderly Type 2 Diabetics.

To investigate the effects of a specific protocol of undulatory physical resistance training on maximal strength gains in elderly type 2 diabetics. The study included 48 subjects, aged between 60 and 85 years, of both genders. They were divided into two groups: Untrained Diabetic Elderly (n=19) with those who were not subjected to physical training and Trained Diabetic Elderly (n=29), with those who were subjected to undulatory physical resistance training. The participants were evaluated with several types of resistance training's equipment before and after training protocol, by test of one maximal repetition. The subjects were trained on undulatory resistance three times per week for a period of 16 weeks. The overload used in undulatory resistance training was equivalent to 50% of one maximal repetition and 70% of one maximal repetition, alternating weekly. Statistical analysis revealed significant differences (p<0.05) between pre-test and post-test over a period of 16 weeks. The average gains in strength were 43.20% (knee extension), 65.00% (knee flexion), 27.80% (supine sitting machine), 31.00% (rowing sitting), 43.90% (biceps pulley), and 21.10% (triceps pulley). Undulatory resistance training used with weekly different overloads was effective to provide significant gains in maximum strength in elderly type 2 diabetic individuals.

Dentine Bond Strength And Antimicrobial Activity Evaluation Of Adhesive Systems.

This study evaluated the dentine bond strength (BS) and the antibacterial activity (AA) of six adhesives against strict anaerobic and facultative bacteria. Three adhesives containing antibacterial components (Gluma 2Bond (glutaraldehyde)/G2B, Clearfil SE Protect (MDPB)/CSP and Peak Universal Bond (PUB)/chlorhexidine) and the same adhesive versions without antibacterial agents (Gluma Comfort Bond/GCB, Clearfil SE Bond/CSB and Peak LC Bond/PLB) were tested. The AA of adhesives and control groups was evaluated by direct contact method against four strict anaerobic and four facultative bacteria. After incubation, according to the appropriate periods of time for each microorganism, the time to kill microorganisms was measured. For BS, the adhesives were applied according to manufacturers' recommendations and teeth restored with composite. Teeth (n=10) were sectioned to obtain bonded beams specimens, which were tested after artificial saliva storage for one week and one year. BS data were analyzed using two-way ANOVA and Tukey test. Saliva storage for one year reduces the BS only for GCB. In general G2B and GCB required at least 24h for killing microorganisms. PUB and PLB killed only strict anaerobic microorganisms after 24h. For CSP the average time to eliminate the Streptococcus mutans and strict anaerobic oral pathogens was 30min. CSB showed no AA against facultative bacteria, but had AA against some strict anaerobic microorganisms. Storage time had no effect on the BS for most of the adhesives. The time required to kill bacteria depended on the type of adhesive and never was less than 10min. Most of the adhesives showed stable bond strength after one year and the Clearfil SE Protect may be a good alternative in restorative procedures performed on dentine, considering its adequate bond strength and better antibacterial activity.