VO2 thin films and nanoparticles for energy-saving applications in architectural elements

Vanadium dioxide (VO2) is a promising material with large interest in construction industry and architecture, due to its thermochromic properties. This material may be used to create "smart" coatings that result in improvements in the buildings energy efficiency, by reducing heat exchanges and, consequently, the need for acclimatization. In this work, VO2 thin films and coatings were produced and tested in laboratory, to apply in architectural elements, such as glass, rooftop tiles and exterior paints. Thin films were produced by RF magnetron sputtering and VO2 nanoparticles were obtained through hydrothermal synthesis, aiming to create "smart" windows and tiles, respectively. These coatings have demonstrated the capability to modulate the transmittance of infrared radiation by around 20%. The VO2 nanoparticle coatings were successfully applied on ceramic tiles. The critical temperature was reduced to around 40ºC by tungsten doping. Ultimately, two identical house models were built, in order to test the VO2 coatings, in real atmospheric conditions during one of the hottest months of the year, in Portugal – August.

Caraterização metrológica de contadores de micro caudal

Nas últimas décadas, as empresas têm sido sujeitas a uma maior concorrência, ao desenvolvimento tecnológico mais acelerado e a novos desafios no que respeita à qualidade. A Metrologia deverá assim acompanhar estas tendências do mercado. O Departamento de Metrologia (DMET) do Instituto Português da Qualidade, I.P. (IPQ) tem vindo a desenvolver esforços significativos que visam a melhoria contínua das técnicas e dos processos de medição e de calibração realizados nos laboratórios. A presente dissertação de mestrado foi realizada no Laboratório de Volume e Caudal (LVC) do DMET. Os objetivos iniciais do trabalho centraram-se na caraterização metrológica de contadores de fluidos, tendo como base a medição do caudal, utilizando como método de referência o método gravimétrico. De forma a validar o sistema de medição foram realizados ensaios entre 1 mL/h a 100 mL/h, em condições de reprodutibilidade, com dois sistemas padrão distintos de acordo com o caudal a ensaiar. Em todos os ensaios efetuados foi necessário monitorizar as condições ambientais, i.e. temperatura, pressão atmosférica, humidade relativa e a temperatura do líquido padrão, para a aplicação das correções necessárias. Outro feito importante foi a caraterização das fontes de incerteza, que permitiram caraterizar o resultado das medições. A metodologia utilizada para a avaliação e para a estimativa da incerteza de medição encontra-se descrita no Guide to the Expression of Uncertainty in Measurement (GUM). Neste projeto foram contempladas fontes de incerteza como as associadas à evaporação, à impulsão do tubo, à resolução da balança, entre outras. Com os resultados obtidos foi possível elaborar um procedimento técnico para a Calibração de Caudalímetros de Líquidos. Os resultados obtidos permitiram garantir a rastreabilidade das medições de caudal de líquidos ao SI, essencial para a calibração de equipamentos no Laboratório Nacional de Metrologia (LNM) do IPQ, nomeadamente para micro caudalímetros no intervalo de medição entre 0,12 mL/h e 600 mL/h.

Distributed solar micro generation

Taking into account the fact that the sun’s radiation is estimated to be enough to cover 10.000 times the world’s total energy needs (BRAKMANN & ARINGHOFF, 2003), it is difficult to understand how solar photovoltaic systems (PV) are still such a small part of the energy source matrix across the globe. Though there is an ongoing debate as to whether energy consumption leads to economic growth or whether it is the other way around, the two variables appear correlated and it is clear that ensuring the availability of energy to match a country’s growth targets is one of the prime concerns for any government. The topic of centralized vs distributed electricity generation is also approached, especially in what regards the latter fit to developing countries needs, namely the lack of investment capabilities and infrastructure, scattered population, and other factors. Finally, Brazil’s case is reviewed, showing that the current cost of electricity from the grid versus the cost from PV solutions still places an investment of this nature with 9 to 16 years to reach breakeven (from a 25 year panel lifespan), which is too high compared to the required 4 years for most Brazilians. Still, recently passed legislation opened the door, even if unknowingly, to the development of co-owned solar farms, which could reduce the implementation costs by as much as 20% and hence reduce the number of years to breakeven by 3 years.

Implementation of a probabilistic based framework for safety assessment of existing timber elements

The assessment of existing timber structures is often limited to information obtained from non or semi destructive testing, as mechanical testing is in many cases not possible due to its destructive nature. Therefore, the available data provides only an indirect measurement of the reference mechanical properties of timber elements, often obtained through empirical based correlations. Moreover, the data must result from the combination of different tests, as to provide a reliable source of information for a structural analysis. Even if general guidelines are available for each typology of testing, there is still a need for a global methodology allowing to combine information from different sources and infer upon that information in a decision process. In this scope, the present work presents the implementation of a probabilistic based framework for safety assessment of existing timber elements. This methodology combines information gathered in different scales and follows a probabilistic framework allowing for the structural assessment of existing timber elements with possibility of inference and updating of its mechanical properties, through Bayesian methods. The probabilistic based framework is based in four main steps: (i) scale of information; (ii) measurement data; (iii) probability assignment; and (iv) structural analysis. In this work, the proposed methodology is implemented in a case study. Data was obtained through a multi-scale experimental campaign made to old chestnut timber beams accounting correlations of non and semi-destructive tests with mechanical properties. Finally, different inference scenarios are discussed aiming at the characterization of the safety level of the elements.

Ontology-based representation and generation of workflows for micro-task human-machine computation

Doctoral Program in Computer Science

Thin panels of cement composites reinforced with recycled fibres for the shear strengthening of reinforced concrete elements

A new technique was developed for producing thin panels of a cement based material reinforced with relatively high content of steel fibres originated from the industry of tyre recycling. Flexural tests with notched and un-notched specimens were carried out to characterize the mechanical properties of this Fibre Reinforced Cement Composite (FRCC) and the results are presented and discussed. The values of the fracture mode I parameters of the developed FRCC were determined by performing inverse analysis with test results obtained in three point notched beam bending tests. To appraise the potentialities of these FRCC panels for the increase of the shear capacity of reinforced (RC) beams, numerical research was performed on the use of developed FRCC panel for shear reinforcement by applying the panels in the lateral faces of RC beams deficiently reinforced in shear.

Investigating the durability of FRP-masonry elements immersed in water

Nowadays, there is an increasing interest in using fiber reinforced polymers (FRP) for strengthening masonry elements. It has been observed that these materials, when used for externally bonded reinforcement (EBR), improve the performance of masonry components. However, issues such as durability and long-term performance of strengthened elements are still open. The bond between composite material and masonry substrate is a critical mechanism in EBR strengthening techniques, and therefore its durability and long-term performance should be deeply investigated and characterized. In the present study, the influence of water immersion on the bond performance is investigated by performing single-lap shear bond tests on two sets of GFRP-strengthened specimens immersed in water for six months. Different surface preparation techniques are used for each set of specimens to study their effect on the bond degradation. The specimens are prepared following the wet lay-up procedure. The observations and the obtained results are presented and discussed.

Biofunctionalization of titanium surfaces for dental implants: osteogenic, anti-microbial and tribocorrosion resistant surfaces

PhD thesis in Biomedical Engineering

Renewable energy system for an isolated micro grid

This paper presents the development of the power electronics needed for the interaction between the electrical generator of a wind turbine and an isolated ac micro grid. In this system there are basically two types of receptors for the energy produced by the wind turbine, which are the loads connected to the isolated micro grid and the batteries used to store energy. There are basically two states in which the system will work. One of the states is when there is enough wind power to supply the loads and the extra energy is used to charge the batteries. The other state is when there is low wind power and the batteries have to compensate the lack of power, so that the isolated micro grid has enough power to supply at least the priority loads. In this paper are presented the hardware and the control algorithm for the developed system. The topology was previously tested in computer simulations, using the software PSIM 9.0, and then validated with the implementation of a laboratory prototype.

Creep behaviour of cracked steel fibre reinforced self-compacting concrete laminar structures

Tese de Doutoramento - Civil Engineering

Quantificação de macro e micro nutrientes em algumas etnovariedades de cubiu (Solanum sessiliflorum Dunal)

Considerando a ampla variabilidade genética de cubiu (Solanum sessiliflorum Dunal), quantificaram-se os macro e micro-nutrientes, objetivando a ampliação da tabela de composição química de alimentos típicos da região amazônica. Os frutos provenientes da Estação Experimental de Hortaliças Alejo von der Pahlen (EEH) do Instituto Nacional de Pesquisas da Amazônia (INPA), localizados no km 14 da Rodovia AM 010 em Manaus, AM, foram processados no Laboratório de Alimentos e Nutrição do INPA. Avaliaram-se oito etnovariedades de cubiu identificados como: 2 I, 3 I, 6, 7, 12, 14, 17, 29 I e III em estádio de maturação comercial. Os teores de elementos minerais foram quantificados pela técnica de Ativação por Nêutrons Instrumental e a fibra alimentar pelo método enzímico-gravimétrico. Os resultados demonstram ser o cubiu um fruto com baixo conteúdo energético (média de 33 kcal), com conteúdo de fibra alimentar total na ordem de 1,6%. Em relação aos macros elementos minerais, a etnovariedade 6, apresentou a maior concentração em potássio (513,5±3,1mg), cálcio (18,9±0,6mg) e a etnovariedade 2 I em Fe (564,4±58,1µg) e Cr (99,3±8,3µg). A menor concentração foi constatada na etnovariedade 12 para os elementos K (229,0±4,5mg), Na (53,7±5,5µg) e Zn (89,3±4,7µg). Apesar das variações em relação as diferentes etno variedades e conseqüentemente concentrações em elementos minerais, o cubiu, pode estar contribuindo para atingir as recomendações desses nutrientes.

Estudo da adaptação da espécie Piper hispidinervum C. DC. (pimenta longa) à região do Vale do Itajaí - SC, através da composição química do óleo essencial obtido por hidrodestilação por micro-ondas e convencional

Neste trabalho, a espécie Piper hispidinervum (pimenta longa), endêmica do estado do Acre, foi cultivada na região do Vale do Itajaí - SC, e sua adaptação foi avaliada em relação à composição química do óleo essencial obtido pelos processos de hidrodestilação convencional e por micro-ondas. O safrol foi identificado como o constituinte majoritário do óleo essencial desta espécie, o qual foi empregado como parâmetro de avaliação da capacidade de adaptação desta planta à região sul do Brasil, já que a proposta abrange avaliar a utilização desta espécie como fonte alternativa de safrol, em substituição a Canela Sassafrás (Ocotea odorifera), espécie muito explorada até a década de 90 nesta região. As amostras da planta foram obtidas de diferentes regiões do Acre e foram cultivadas na estação experimental da EPAGRI - Itajaí-SC. O óleo essencial das folhas forneceu um teor médio de safrol entre 76,6% e 89,9%. A análise por CG-DIC e CG-EM do óleo com maior concentração de safrol, apresentou os seguintes constituintes: safrol (89,93%), α-terpineno (0,35%), (E)-β-ocimeno (0,54%), terpinoleno (3,10%), valenceno (0,21%), (Z)-β-bisaboleno (1,70%) e guaiol (0,29%).

Brazil nuts: determination of natural elements and aflatoxin

A study was carried out to evaluate the association of levels of radioactivity, selenium and aflatoxin in shelled Brazil nuts, which were classified in different sizes, for export. The selenium determinations were performed by inductively coupled plasma optical emission spectrometry (LOQ = 3.0 µg g-1), and aflatoxins were detected by Liquid chromatography-mass spectrometry (LOQ = 0.85 µg kg-1), recovery rates were between 92 and 100%. Radioactivity was measured by high-resolution gamma spectrometry. The selenium mean concentration was (22.7 ± 7.4) µg g-1. (n = 30). Mean activities determined for the following radium isotopes were: 15.77 Bq kg-1 for 224Ra, 104.8 Bq kg-1 for 226Ra and 99.48 Bq kg-1 for 228Ra. For 226Ra, the levels did not vary significantly with nut sizes, although such differences were observed for 224Ra and 228Ra. There was no statistically significant association between the level of selenium and the activity of radionuclides, however, there was correlation between the radionuclides. Aflatoxins above the quantification limit were not found.

Wear of PEEK-Ti6Al4V systems under micro-abrasion and linear sliding conditions

Dissertação de mestrado integrado em Engenharia Biomédica

Controlled aggregation of gold nanoparticles in a di-ureasilmatrix. Optical and micro indentation investigation

Nanocomposite materials with an organic-inorganic urea-silicate (di-ureasil) based matrix containing gold nanoparticles (NPs) were synthesized and characterized by optical (UV/Vis) spectroscopy and indentation measurement. The urea silicate gels were obtained by reaction between silicon alkoxyde modified by isocyanate group and polyethylene glycol oligomer with amine terminal groups in presence of catalyst. The latter ensures the successful incorporation of citrate-stabilized gold NPs in the matrix. It is shown that using a convenient destabilizing agent (AgNO3) and governing the preparative conditions, the aggregation degree of gold NPs can be controlled. The developed synthesis procedure significantly simplifies the preparative procedure of gold/urea silicate nanocomposites, compared to the procedure using gold NPs, preliminary covered with silica shells. Mechanical properties of the prepared sample were characterised using depth sensing indentation methods (DSI) and an idea about the type of aggregation structures was suggested.