Compósitos de matriz metálica à base níquel com adição de TaC e NbC produzidos via metalurgia do pó

Carbide reinforced metallic alloys potentially improve some important mechanical properties required for the overall use of important engineering materials such as steel and nickel. Nevertheless, improved performance is achieved not only by composition enhancement but also by adequate processing techniques, such as novel sintering methods in the case of powder metallurgy. The method minimizes energy losses in addition to providing uniform heating during sintering. Thus, the general objective of this study was to evaluate the density, hardness, flexural strength, dilatometric behavior and to analyze the microstructure of metal matrix composites based nickel with addition of carbides of tantalum and / or niobium when sintered in a conventional furnace and Plasma assisted debinding and sintering (PADS). Initially, were defineds best parameters of granulation, screening and mixing procedure. After, mixtures of carbonyl Ni and 5%, 10% and 15 wt.% NbC and TaC were prepared in a Y-type mixer under wet conditions during 60 minutes. The mixtures were then dried and granulated using 1.5 wt. % paraffin diluted in hexane. Granulates were cold pressed under 600 MPa. Paraffin was then removed from the pressed pellets during a pre-sintering process carried out in a tubular furnace at 500 °C during 30 min. The heating rate was 3 ºC/min. The pellets were then sintered using either a plasma assisted reactor or a conventional resistive tubular furnace. For both methods, the heating rate was set to 8 ºC/min up to 1150 °C. The holding time was 60 minutes. The microstructure of the sintered samples was evaluated by SEM. Brinell hardness tests were also carried out. The results revealed that higher density and higher hardness values were observed in the plasma-assisted sintered samples. Hardness increased with the concentration of carbides in the Ni-matrix. The flexural strength also increased by adding the carbides. The decline was larger for the sample with addition of 5% 5% TaC and NbC. In general, compositions containing added carbide 10% showed less porous and more uniform distribution of carbides in the nickel matrix microstructural appearance. Thus, both added carbide and plasma sintering improved density, hardness, flexural strength and microstructural appearance of the composites

Efeito da adição de fibras da palma do licuri (syagrus coronata) no comportamento físico e mecânico de compósitos de matriz cimentícia

This research was motivated by the requirement of asbestos s replacement in building systems and the need to generate jobs and income in the country side of the state of Bahia, Brazil. The project aimed at using fibers from licuri leaves (syagrus coronata), an abundant palm in the region, to produce composites appropriate for the sustainable production of cement fibre reinforced products in small plants. The composites were produced in laboratory using Portland cement CP-II-F32, sand, water, licuri palm fiber contents of 1.0, 1.5 and 2.0% by weight of binder (two different fiber length) and metakaolin. The latter was chosen as an additional binder for its efficiency to reduce the alkalinity of cementitious matrixes therefore preventing the degradation of vegetable fibers. The characterization of the composite components was carried out by sieving and laser particle size analyses, thermal analysis, fluorescence and X-ray diffraction. The composites performance was evaluated by 3- point-bending tests, compressive strength, ultrasound module of elasticity, free and restrained shrinkage, water capillarity absorption and apparent specific gravity. It has been found that the addition of fibers increased the time to onset of cracking over 200.00% and a 25% reduction in cracks opening in the restrained shrinkage test. The capillary absorption reduced about 25% when compared to fiber-free composites. It was also observed with regard to flexural strength, compressive strength and specific gravity, that the addiction of fibers did not affect the composite performance presenting similar results for compounds with and without fibers. In general it can be stated that the reinforced composite fibers of palm licuri presents physical and mechanical characteristics which enable them to be used in the intended proposals of this research

O corpo como matriz pedagógica

The contemporary conjuncture based on the capitalistic knowledge converges to the corporal consciousness that makes us see, feel, taste and hear, be in/to pieces. Disembodied reason legitimate and legislate ways of being and living socially and its development is the dehumanization of human relations causing pain and suffering. The objective of this work is to discuss the body as pedagogical matrix through imagistic/artistic elements: music, painting and literature. Metaphors lead to self knowledge of human subjectivity and approach us to the kaleidoscope of sensitive knowledge and enables learning to learn with the infinite combinations of images, knowledge, feelings and worldviews. The song Memória da Pele comes in the voice of Maria Betânia speak of the memories that are not mine, but are tattooed in me in the memory of skin, singing the memories of a love lived by who tries to forget rationally, but the body insists on remembering. It is password to think about what we are. The short story by Clarice Lispector, entitled Miss Algarve, narrates the life story of an unmarried and virgin woman, and her encounter with an alien called Ixtlan. Until then, she who lived as if every day were a Monday, found herself seduced by the pleasure of having a body in contact with another body, which also allowed her to give visibility to the bodies of others. She had repudiation by the immorality that her body and the other s perspired. The discovery of the body brings important lessons for nursing, involving our body and the others'. The painting the flying bed or Henry Ford Hospital, by Frida Kahlo, is our final metaphor. The traumatic experience of abortion is shown in this painting trough the picture of the artist naked in a hospital bed. This painting invites us to reflect on our work process. We need to think in multiple dimensions of the being and accept the invitation of art, so that the lightness confronts us with the weight imposed by the hegemonic ideology. I believe it is not a single view, but the many views that should justify the knowledge and practices of nursing; what matters is that they are woven into the dialogue, democracy, provided that protagonism of those individuals involved in this process, in the wandering and uncertainty, in the rewiring, solidarity, plurality. To this end, the body must be the great pedagogue that is able to be viewed not as a tapestry seen by the right view, as the logical knowledge sees, but seen by the opposite side in its singular, irregular, discontinuous weavings

Emergência de plântulas de pequizeiro em função da planta matriz e uso de ácido giberélico

Em Goiás, o pequi (Caryocar brasiliense) se destaca, dentre as frutíferas nativas do Cerrado, como promissora para a produção comercial. Um dos obstáculos para a sua produção em grande escala, no entanto, é o fato de que a germinação de sementes seja baixa e irregular. Com o objetivo de avaliar a emergência de sementes de pequizeiro e o desenvolvimento inicial de mudas oriundas de 16 plantas, aos dez meses após a colheita, na presença e ausência de ácido giberélico (GA3), foram conduzidos dois experimentos. O primeiro foi implantado em delineamento de blocos ao acaso, com parcelas subdivididas, tendo as matrizes nas parcelas e, nas subparcelas, um tratamento de imersão por 48 horas, em água pura e em solução de 500 mg L-1 de GA3. Foram realizadas avaliações a cada sete dias, para determinação da percentagem final, tempo médio e índice de velocidade de emergência. Para o segundo experimento, foi utilizado delineamento inteiramente casualizado, com número variado de repetições, de acordo com o número de mudas obtidas no primeiro experimento. Para percentagem, índice de velocidade e tempo médio de emergência, o efeito dos tratamentos foi significativo, sendo que, para os dois primeiros, houve interação significativa entre genótipo e tratamento, para superação da dormência. Observou-se que a utilização de 500 mg L-1 de ácido giberélico pode minimizar a dormência em sementes de Caryocar brasiliense e que o crescimento das matrizes em campo foi linear e contínuo, ao longo do tempo.

Análise do balanço energético e da matriz de emissões de poluentes no Estado do Rio Grande do Norte

This thesis intends to show the level of pollutant emissions in the State of Rio Grande do Norte, generated by the final consumption of energy in the many different sectors of the economy. This information was obtained from the energetic matrix and from the pollutant emissions of the State and the data was taken from the Balanço Energético Estadual and from the Sistema de Informações Energéticas da Olade. The result will permit to identify the energy and most polluting economic sectors in Rio Grande do Norte, contributing to energy planning, giving direction to the public policy development that aim at the change of the energy matrix of the State. Also with the objective of reducing pollutant emissions through rationalization, efficiency and energy substitution, which the main objective is to promote the economic development based on energy consumption of less harmful impact on the environment, contributing to establishment of sustainable development

Avaliação da matriz nutricional da enzima fitase em rações contendo sorgo para poedeiras comerciais

Avaliaram-se os efeitos da inclusão de fitase e de sua matriz nutricional em rações contendo sorgo sobre o desempenho das aves, a qualidade dos ovos, a ingestão e a excreção e retenção de fósforo e nitrogênio em poedeiras comerciais. Utilizaram-se 180 poedeiras comerciais, distribuídas em delineamento inteiramente ao acaso em esquema fatorial 2 × 2 + 1, com dois níveis de fitase (0 e 500 FTU/kg de ração) e dois níveis de substituição do milho pelo sorgo (50 e 100%) e uma ração testemunha (isenta de sorgo e fitase), constituindo cinco tratamentos com seis repetições de seis aves. As rações foram à base de milho e farelo de soja, sem fitase e sorgo, considerando a matriz nutricional da fitase. O desempenho e a qualidade dos ovos foram avaliados em quatro períodos de 28 dias. Ao final do experimento, um ensaio de metabolismo foi realizado para quantificar a ingestão, excreção e retenção aparente de fósforo e nitrogênio e avaliar a viabilidade econômica das rações. Ao considerar a matriz nutricional da fitase, as exigências em energia, cálcio, fósforo, proteína e aminoácidos foram atendidas, mesmo com a redução dos níveis nutricionais da dieta, e o desempenho e a qualidade dos ovos não foram comprometidos. A adição de fitase nas rações possibilitou reduzir todos os parâmetros econômicos avaliados. O sorgo pode substituir totalmente o milho e ser o único grão energético da dieta.

Avaliação técnica e econômica da matriz nutricional da enzima fitase em rações contendo farelo de girassol para poedeiras comerciais

Cento e oitenta poedeiras comerciais Isa Brown, com 60 semanas de idade, foram distribuídas em delineamento inteiramente ao acaso, em esquema fatorial 2 õ 2, com dois níveis de fitase (0 e 500 ftu/kg de ração) e dois de farelo de girassol (4 e 8%), totalizando cinco dietas, avaliadas com seis repetições de seis aves. As dietas foram formuladas a partir de uma ração controle, à base de milho e farelo de soja, isenta de fitase e farelo de girassol, valorizando na formulação das dietas a matriz nutricional da fitase. O período experimental foi dividido em quatro ciclos de 28 dias cada. A matriz nutricional preconizada para fitase permitiu o atendimento pleno das exigências das aves, mesmo quando as dietas foram formuladas com níveis nutricionais reduzidos, isso quando desconsiderados os nutrientes presentes na matriz nutricional da enzima, de acordo com recomendação da empresa produtora. A adição de fitase na dieta reduz a excreção de fósforo pelas aves e melhora os parâmetros econômicos. A inclusão de farelo de girassol no nível de 8% prejudica a produção de ovos, mas não afeta os demais parâmetros de desempenho e qualidade dos ovos.

Enumeração de espectro de distâncias de esquemas de modulação codificada em treliça empregando codificação turbo

In this work, a performance analysis of transmission schemes employing turbo trellis coded modulation. In general, the performance analysis of such schemes is guided by evaluating the error probability of these schemes. The exact evaluation of this probability is very complex and inefficient from the computational point of view, a widely used alternative is the use of union bound of error probability, because of its easy implementation and computational produce bounds that converge quickly. Since it is the union bound, it should use to expurge some elements of distance spectrum to obtain a tight bound. The main contribution of this work is that the listing proposal is carried out from the puncturing at the level of symbol rather than bit-level as in most works of literature. The main reason for using the symbol level puncturing lies in the fact that the enummerating function of the turbo scheme is obtained directly from complex sequences of signals through the trellis and not indirectly from the binary sequences that require further binary to complex mapping, as proposed by previous works. Thus, algorithms can be applied through matrix from the adjacency matrix, which is obtained by calculating the distances of the complex sequences of the trellis. This work also presents two matrix algorithms for state reduction and the evaluation of the transfer function of this. The results presented in comparisons of the bounds obtained using the proposed technique with some turbo codes of the literature corroborate the proposition of this paper that the expurgated bounds obtained are quite tight and matrix algorithms are easily implemented in any programming software language

Estudo das propriedades termofísicas com variação da expansibilidade de compósito desenvolvido com matriz PUR-NOP e carga funcional de argilomineral

In this study were conducted experimental procedures for determination of variation of the expandability of rigid polyurethane foam (PUR) from a natural oil polyol (NOP), specifically the Castor oil plant, Ricinus communis, pure and additions of the vermiculite in phase dispersed in different percentage within a range from 0% to 20%, mass replacement. From the information acquired, were defined the parameters for production of bodies of test, plates obtained through controlled expansion, with the final volume fixed. Initially, the plates were subjected to thermal performance tests and evaluated the temperature profiles, to later be extracted samples duly prepared in accordance with the conditions required for each test. Was proceeded then the measurement of the coefficient of thermal conductivity, volumetric capacity heat and thermal diffusivity. The findings values were compared with the results obtained in the tests of thermal performance, contributing to validation of the same. Ultimately, it was investigated the influence that changes in physical-chemical structure of the material had exerted on the variation of thermophysical quantities through gas pycnometry, scanning electron microscopy (SEM) combined with energy dispersive X-ray fluorescence spectroscopy (EDXRF), infrared spectroscopy using Fourier transform (FTIR), thermogravimetric analysis (TGA) and differential thermal analysis (DTA). Based on the results obtained was possible to demonstrate that all load percentage analyzed promoted an increase in the potential expansion (PE) of the resin. In production of the plates, the composites with density near at the free expansion presented high contraction during the cure, being the of higher density adopted as definitive standard. In the thermal performance tests, the heating and cooling curves of the different composites had presented symmetry and values very close for lines of the temperature. The results obtained for the thermophysical properties of composites, showed little difference in respect of pure foam. The percentage of open pores and irregularities in the morphology of the composites were proportionate to the increment of vermiculite. In the interaction between the matrix and dispersed phase, there were no chemical transformations in the region of interface and new compounds were not generated. The composites of PUR-NOP and vermiculite presented thermal insulating properties near the foam pure and percentage significantly less plastic in its composition, to the formulation with 10% of load

Estudo do aproveitamento de resíduo de gesso como carga para compósito com matriz de resina expansiva de mamona

In the execution of civil engineering works, either by wasting during the coating of wall or demolition of gypsum walls, the generation of the gypsum waste involves serious environmental concerns. These concerns are increased by the high demand of this raw material in the sector and by the difficulties of proper disposal byproduct generated. In the search for alternatives to minimize this problem, many research works are being conducted, giving emphasis in using gypsum waste as fillers in composites materials in order to improve the acoustic, thermal and mechanical performances. Through empirical testing, it was observed that the crystallization water contained in the residue (CaSO4.2H2O) could act like primary agent in the expanding of the polyurethane foam. Considering that polyurethane produced from vegetable oils are biodegradable synthetic polymers and that are admittedly to represent an alternative to petrochemical synthetic polyurethane, this research consist an analysis of the thermal behavior of a composite whose matrix obtained from a resin derived from the expansive castor oil seed, with loads of 4%, 8%, 12% and 16% of gypsum waste replacing to the polyol prepolymer blend. Contributors to this analysis: a characterization of the raw material through analysis of spectroscopy by Fourier transform infrared (FTIR), chemical analysis by X-Ray Fluorescence (XRF) and mineralogical analysis by X Ray Diffraction (XRD), complemented by thermo gravimetric analysis (TGA). In order to evaluate the thermo physical properties and thermal behavior of the composites manufactured in die closed with expansion contained, were also carried tests to determine the percentage of open pore volume using a gas pycnometer, scanning electronic microscopy (SEM), in addition to testing of flammability and the resistance to contact with hot surfaces. Through the analysis of the results, it appears that it is possible to produce a new material, which few changes in their thermo physical properties and thermal performance, promotes significant changes and attractive to the environment

Desenvolvimento e análise de material compósito a base de penas de frango (fibras de queratina-KF) e matriz de poliéster insaturado

Use of natural fibres as a reinforcement material in the manufacture of composites show a series of advantages: availability, biodegradability, low weight and regeneration in relation to synthetic fibres, thus justifying its utilization. In the present research work, composites were developed with chicken feathers (KF), using unsaturated polyester resin as matrix, for diversified applications, mainly in the furniture/timber industry.At present, in Brazil the chicken feathers are used as part of the animal feed, even though this material possesses low aggregated value. The chicken feathers are hollow, light and resistant. After washing with water at room temperature, a part of the chicken feathers were treated with 2% NaOH. Composites were manufactured using treated and untreated chicken feathers with unsaturated orthothalic polyester resin and 1% peroxide as catalyser, obtained in the commerce. Samples with size 150x25x3 mm for mechanical tests were cut by laser in the composite plate. Mechanical analyses were carried out in the Laboratório de Metais e Ensaios Mecânicos UFRN. All the analyses were in accordance with ASTM standards. SEM analyses were also carried out on the samples.In the analyses of the results obtained, it was observed that the composites made with untreated chicken feathers showed better results (Traction 11.406 MPa and 9.107 MPa Bending 34.947 and 20.918 MPa for samples with and without treatment respectively) compared to the composite with treated feathers. Very low values of the water absorption results, evidenced the impermeability characteristic of the feathers. From the SEM images, the structure, fracture and the fibre/matrix adsorption can be evidenced. In the flammability test, it was observed that despite the feathers having sulfur as a constituent, natural inhibitor of flame, no burning support of the composites, because the manufacturing process of the composite

Análise térmica e mecânica de um compósito de matriz cerâmica com carga de EPS e raspa de pneu para construção de casas populares

Space Science was built using a composite made of plaster, EPS, shredded tires, cement and water. Studies were conducted to thermal and mechanical resistance. Inside the mold EPS plates were placed in order to obtain a higher thermal resistance on the wall constructed, as well as to give it an end environmentally friendly in view of both the tire and the EPS occupy a large space in landfills and year need to be degraded when released into the environment. Compression tests were performed according to ABNT blocks to seal, measurements of the temperature variation in the external and internal walls using a laser thermometer and check the temperature of the indoor environment using a thermocouple attached to a digital thermometer. The experiments demonstrated the heat provided by the composite values from the temperature difference between the internal and external surfaces on the walls, reaching levels of 12.4 ° C and room temperature in the interior space of the Science of 33.3 ° C, remaining within the zone thermal comfort for hot climate countries. It was also demonstrated the proper mechanical strength of such a composite for sealing walls. The proposed use of the composite can contribute to reducing the extreme housing shortage in our country, producing popular homes at low cost and with little time to work

Estudo de um compósito de matriz cerâmica com carga de recicláveis para o uso na construção civi

With a view to revitalizing public environments through criteria that include economy, tourism, aesthetics and respect for the environment, this paper proposes a model of kiosk manufactured with composite material blocks, to be employed as a public instrument. . The model consists of a structure composed of planned blocks and manufactured in cement-based composite, gypsum, ground and water, having the styrofoam inside filled with pet bottles of 500 ml dose. The social and environmental issue is the critical point of the work when it can, through the reuse of environmentally harmful materials such as polyethylene terephthalate PET, using such modules for the construction of various areas of Commerce, promoting the protection of the environment combined with the improvement of the quality of life of the population. The tourism factor, which is significant in the economy of the North, is also considered as the modulated kiosk has a visual aspect innovative and differentiated. The environmental issue is addressed by encouraging the reuse of PET material and EPS (polystyrene)

Viabilidade de utilização de um compósito de matriz cerâmica com cargas recicláveis na fabricação de equipamentos solares

Composite materials can be defined as materials formed from two or more constituents with different compositions, structures and properties, which are separated by an interface. The main objective in producing composites is to combine different materials to produce a single device with superior properties to the component unit. The present study used a composite consisting of plaster, cement, EPS, tire, PET and water to build prototype solar attempt to reduce the manufacturing cost of such equipment. It was built two box type solar cookers, a cooler to be cooled by solar energy, a solar dryer and a solar cooker concentration. For these prototypes were discussed the processes of construction and assembly, determination of thermal and mechanical properties, and raising the performance of such solar systems. Were also determined the proportions of the constituents of the composite materials according to specific performance of each prototype designed. This compound proved to be feasible for the manufacture of such equipment, low cost and easy manufacturing and assembly processes

Incorporação de resíduo de perfuração em matriz cerâmica: estabilização por solidificação

One of the waste generated during the drilling of oil wells are gravel which are impregnated of drilling fluid. This residue consists of highly toxic chemicals, including toxic metals. This study suggests an alternative process to the treatment of this waste, by incorporating it the form of raw material in the ceramic matrix , and by solidification and stabilize the metals present, Aluminum (Al), Iron (Fe), Manganese (Mn) and Zinc (Zn). The raw materials were characterized by the techniques of X ray fluorescence (FRX), X ray diffraction (DRX), laser granulometry (GL), thermogravimetry (TG) and differential thermal analysis (ADT). To evaluate the percentage of gravel effect the environmental and technological properties were obtained from formulations containing 0, 10 and 20 % by weight of gravel in the ceramic matrix. After sintering at temperatures 1080, 1120 and 1160 °C, the samples were tested for water absorption, the linear shrinkage firing, voltage of rupture and solubility. The results obtained showed that the stabilization by solidification, is a viable alternative to safe disposal of waste drilling. Ceramics products can be used in the manufacture of solid bricks