Pounding force assessment in performance-based design of bridges

Bridges with deck supported on either sliding or elastomeric bearings are very common in mid-seismicity regions. Their main seismic vulnerabilities are related to the pounding of the deck against abutments or between the different deck elements. A simplified model of the longitudinal behavior of those bridges will allow to characterize the reaction forces developed during pounding using the Pacific Earthquake Engineering Research Center framework formula. In order to ensure the general applicability of the results obtained, a large number of system parameter combinations will be considered. The heart of the formula is the identification of suitable intermediate variables. First, the pseudo acceleration spectral value for the fundamental period of the system (Sa(Ts)) will be used as an intensity measure (IM). This IM will result in a very large non-explained variability of the engineering demand parameter. A portion of this variability will be proved to be related to the relative content of high-frequency energy in the input motion. Two vector-valued IMs including a second parameter taking this energy content into account will then be considered. For both of them, a suitable form for the conditional intensity dependence of the response will be obtained. The question of which one to choose will also be analyzed. Finally, additional issues related to the IM will be studied: its applicability to pulse-type records, the validity of scaling records and the sufficiency of the IM.

Seismic vulnerability analysis of wide-beam buildings in Spain

A number of short-to-mid height RC buildings with wide beams have been constructed in moderate-seismicity areas of Spain. The seismic behavior in the direction of the wide beams appears to be deficient because of low lateral strength, low ductility of the wide beams, big strut compressive forces inside the column-beam connections, and unreliable contribution of the spandrel zones of the wide beams. In the orthogonal direction, the behavior is worse since only the joists and the façade beams contribute to the lateral resistance. The objective is to assess the seismic capability of these structures; further research will involve proposing retrofit strategies. The research approach consists of selecting a number of representative buildings and evaluating their vulnerability by code-type, push-over and dynamic analyses. The cooperation of the masonry infill walls is accounted for. The main conclusion is that the seismic behavior of these buildings is inadequate in most of the situations.

Modelling of Topographic Irregularities for Seismic Site Response

Seismic evaluation methodology is applied to an existing viaduct in the south of Spain, near Granada, which is a medium seismicity region. The influence of both geology and topography in the spatial variability of ground motion are studied as well as seismic hazard analysis and ground motion characterization. Artificial hazard-consistent ground motion records are synthesised applying seismic hazard analysis and site effects are estimated through a diffraction study. Direct BEM is used to calculate the valley displacement response to vertically propagating SV waves and transfer functions are generated allowing the transformation of free field motion to motion at each support. A closed formulae is used to estimate these transfer function. Finally, the results obtained are compared.

An evaluation of seismic hazard in La Hispaniola, after the 2010 Haiti earthquake

An evaluation of the seismic hazard in La Hispaniola Island has been carried out, as part of the cooperative project SISMO-HAITI, supported by the Technical University of Madrid (UPM) and developed by several Spanish Universities, the National Observatory of Environment and Vulnerability) ONEV of Haiti, and with contributions from the Puerto Rico Seismic Network (PRSN) and University Seismological Institute of Dominican Republic (ISU). The study was aimed at obtaining results suitable for seismic design purposes. It started with the elaboration of a seismic catalogue for the Hispaniola Island, requiring an exhaustive revision of data reported by more than 20 seismic agencies, apart from these from the PRSN and ISU. The final catalogue contains 96 historical earthquakes and 1690 instrumental events, and it was homogenized to moment magnitude, Mw. Seismotectonic models proposed for the region were revised and a new regional zonation was proposed, taking into account geological andtectonic data, seismicity, focal mechanisms, and GPS observations. In parallel, attenuation models for subduction and crustal zones were revised in previous projects and the most suitable for the Caribbean plate were selected. Then, a seismic hazard analysis was developed in terms of peak ground acceleration, PGA, and spectral accelerations, SA (T), for periods of 0.1, 0.2, 0.5, 1 and 2s, using the Probabilistic Seismic Hazard Assessment (PSHA) methodology. As a result, different hazard maps were obtained for the quoted parameters, together with Uniform Hazard Spectra for Port au Prince and the main cities in the country. Hazard deaggregation was also carried out in these towns, for the target motion given by the PGA and SA (1s) obtained for return periods of 475, 975 and 2475 years. Therefore, the controlling earthquakes for short- and long-period target motions were derived. This study was started a few months after the 2010 earthquake, as a response to an aid request from the Haitian government to the UPM, and the results are available for the definition of the first building code in Haiti.

Contribución metodológica para incorporar fallas activas en la modelización de la fuente dirigida a estimaciones de peligrosidad sísmica. Aplicación al sur de España

En el presente trabajo se desarrolla una metodología para caracterizar fallas activas como fuentes sísmicas independientes en combinación con zonas sismogenéticas tipo área de cara a la estimación probabilista poissoniana de la peligrosidad sísmica. Esta metodología está basada en el reparto de la tasa de momento sísmico registrada en una región entre las fuentes potencialmente activas subyacentes (fallas activas modelizadas de forma independiente y una zonificación sismogenética), haciendo especial hincapié en regiones de sismicidad moderada y fallas de lento movimiento. Se desarrolla una aplicación de la metodología en el sureste de España, incorporando al cálculo 106 fuentes sísmicas independientes: 95 de tipo falla (catalogadas como fallas activas en la base de datos QAFI) y 11 zonas sismogenéticas de tipo área. Del mismo modo, se estima la peligrosidad sísmica con el método clásico zonificado y se comparan los resultados, analizando la influencia de la inclusión de las fallas de forma independiente en la estimación de la peligrosidad. Por último, se desarrolla una aplicación de la metodología propuesta en la estimación de la peligrosidad sísmica considerando un modelo temporal no poissoniano. La aplicación se centra en la falla de Carboneras, mostrando la repercusión que puede tener este cambio de modelo temporal en la estimación final de la peligrosidad. ABSTRACT A new methodology of seismic source characterization to be included in poissonian, probabilistic seismic hazard assessments, is developed in this work. Active faults are considered as independent seismogenic sources in combination with seismogenic area sources. This methodology is based in the distribution of the seismic moment rate recorded in a region between the potentially active underlying seismic sources that it contains (active faults modeled independently and an area-source seismic model), with special emphasis on regions with moderate seismicity and faults with slow deformation rates. An application of the methodology is carried out in the southeastern part of Spain, incorporating 106 independent seismic sources in the computations: 95 of fault type (catalogued as active faults in the Quaternary Active Fault Database, QAFI) and 11 of area-source type. At the same time, the seismic hazard is estimated following the classical area-source method. The results obtained using both methodologies (the classical one and the one proposed in this work9 are compared, analyzing the influence of the inclusion of faults as independent sources in hazard estimates. Finally, an application of the proposed methodology considering a non-poissonian time model is shown. This application is carried out in the Carboneras fault and shows the repercussion that this change of time model has in the final hazard estimates.

Stability analysis of dam failures. Application to aurul tailing pond in Baia Mare (Romania)

La gestión de estériles de una explotación minera es un punto clave en el desarrollo económico de una actividad extractiva, y en especial, del entorno natural y social en el que se emplaza dicho proyecto. La minería de metales preciosos lleva asociada la construcción de balsas de residuos muy peligrosos, fruto de su proceso extractivo, como por ejemplo la cianuración en el caso del oro. Para un correcto funcionamiento de dichos emplazamientos es necesario escoger correctamente el método constructivo a partir de estudios de reconocimiento previos, como estudios de estabilidad geotécnica, contexto geológico de la zona, sismicidad, hidrología, etc. Así mismo, han de llevarse a cabo unas exhaustivas medidas de control y vigilancia para asegurar las condiciones de seguridad exigidas. La ruptura de la balsa de decantación de Aurul S.A. en Baia Mare (Rumania) el 30 de Enero del año 2000 ha sido escogido como caso de estudio de estabilidad de diques. ABSTRACT Tailing's management of a mining exploitation is a key point in the economical development of the extractive activity and, especially, of the natural and social environment of the site. Precious metals mining has high hazardous embankment construction associated, product of its extractive process, i.e. gold cyanidation. A correct operation of those sites makes necessary to choose a suitable construction method, based on previous studies as geotechnical stability studies, geological context of the area, seismicity, hydrology, etc. At the same time, exhaustive control and monitoring must be carried out in order to assure the required safety conditions. Aurul's decantation pond failure in Baia Mare (Romania), on 30th January 2000, has been chosen as a stability analysis case-study.

Comportamiento, para el terremoto de Lorca de 11-05-2011, de edificios de vigas planas proyectados sin tener en cuenta la acción sísmica

(SPA) El terremoto de Lorca (11-05-2011) fue el movimiento sísmico más destructivo registrado en España, a pesar de su moderada magnitud. Este artículo describe la simulación numérica de la respuesta dinámica, al registro principal del terremoto de Lorca, de seis edificios de tres y seis plantas con forjados unidireccionales de hormigón con vigas planas; estos edificios fueron proyectados sin tener en cuenta la acción sísmica. Se ha elegido esta tipología constructiva por presentar, potencialmente, una elevada vulnerabilidad sísmica. Los seis edificios han sido seleccionados para representar un número importante de edificios de este tipo existentes en zonas de sismicidad baja o media (como Lorca) de España y correspondientes a los años 1974-1994, posteriores a la PDS-1 1974 y previos a la NCSE-94. Los resultados obtenidos muestran que estos edificios, aun contando con la cooperación de los muros, no poseen capacidad para resistir la componente más intensa del registro de Lorca. (ENG)The recent earthquake in Lorca (11-05-2011) was the most destructive recorded event in Spain, despite its moderate magnitude. This paper describes the numerical simulation of the dynamic response to the main record of the Lorca earth-quake of six 3 and 6-story buildings with one-way concrete slabs with wide beams; these buildings were designed without any seismic consideration. We have chosen this type of construction because it is potentially highly vulnerable. The six considered buildings were selected to represent a large number of buildings of this type in areas of low-to-medium seismicity (as Lorca) of Spain along the period 1974-1994. The results show that these buildings, even with the cooperation of the walls, do not have sufficient capacity to withstand the most severe component of the Lorca record.

Sismicidad inducida por la manipulación del subsuelo

Los terremotos inducidos por la inyección de gas realizadas en la plataforma continental del golfo de Valencia, proyecto El Castor, en septiembre-octubre 2013, han creado cierta alarma social en las poblaciones costeras próximas. Esto, que es novedoso en España, ha ocurrido con cierta frecuencia en otras áreas pobladas en distintos países y por causa de varios tipos de manipulación del subsuelo. Este artículo intenta ilustrar el problema de la sismicidad inducida por la actividad del hombre. Según se describe en el texto, la sismicidad inducida tiene unos límites, máximo terremoto inducido, que pueden ser investigados en cada caso. De esa manera, se pueden establecer protocolos de actuación que impidan que dichas actividades causen daños materiales en las localidades próximas. Earthquakes induced by the gas injection in the continental platform, of the golf of Valencia, Castor Project, last September-October 2013, has motivated some social alarm within the nearby coastal population. That, which is new for Spain, has happened with some frequency at some other populated areas, in different countries and due to various types of subsoil manipulations. This article tries to illustrate the induced seismicity problem due to human activities. As it is described in the text, the induced seismicity has some limits (maximum induced earthquake) that can be investigated for each particular case. By this way, protocols of operation can be established to avoid that theses activities might cause material damage to local population.

Modelización de las fallas activas para la estimación de la Peligrosidad Sísmica. Aplicación Metodológica en Haití

The development of this Master's Thesis is aimed at modeling active for estimating seismic hazard in Haití failures. It has been used zoned probabilistic method, both classical and hybrid, considering the incorporation of active faults as independent units in the calculation of seismic hazard. In this case, the rate of seismic moment is divided between the failures and the area seismogenetic same region. Failures included in this study are the Septentrional, Matheux and Enriquillo fault. We compared the results obtained by both methods to determine the importance of considering the faults in the calculation. In the first instance, updating the seismic catalog, homogenization, completeness analysis and purification was necessary to obtain a catalog ready to proceed to the estimation of the hazard. With the seismogenic zoning defined in previous studies and the updated seismic catalog, they are obtained relations Gutenberg-Richter recurrence of seismicity, superficial and deep in each area. Selected attenuation models were those used in (Benito et al., 2011), as the tectonic area of study is very similar to that of Central America. Its implementation has been through the development of a logical in which each branch is multiplied by an index based on the relevance of each combination of models. Results are presented as seismic hazard maps for return periods of 475, 975 and 2475 years, and spectral acceleration (SA) in structural periods: 0.1 - 0.2 - 0.5 - 1.0 and 2.0 seconds, and the difference accelerations between maps obtained by the classical method and the hybrid method. Maps realize the importance of including faults as separate items in the calculation of the hazard. The morphology of the zoned maps presented higher values in the area where the superficial and deep zone overlap. In the results it can determine that the minimum values in the zoned approach they outweigh the hybrid method, especially in areas where there are no faults. Higher values correspond to those obtained in fault zones by the hybrid method understanding that the contribution of the faults in this method is very important with high values. The maximum value of PGA obtained is close to Septentrional in 963gal, near to 460 gal in Matheux, and the Enriquillo fault line value reaches 760gal PGA in the Eastern segment and Western 730gal in the segment. This compares with that obtained in the zoned approach in this area where the value of PGA obtained was 240gal. These values are compared with those obtained by Frankel et al., (2011) with those have much similarity in values and morphology, in contrast to those presented by Benito et al., (2012) and the Standard Seismic Dominican Republic

Desarrollos metodológicos y aplicaciones hacia el cálculo de la peligrosidad sísmica en el ecuador continental y estudio de riesgo sísmico en la ciudad de Quito

En el presente trabajo de tesis se desarrolla, en primer lugar, un estudio de peligrosidad sísmica en Ecuador continental, siguiendo una metodología probabilista zonificada. El estudio se plantea a escala regional y presenta como principales aportaciones: 1) la elaboración de un Estado del Arte sobre Tectónica y Geología de Ecuador, concluyendo con la identificación de las principales fuentes sísmicas; 2) La confección de un Catálogo Sísmico de proyecto, recopilando información de distintas agencias, que ha sido homogeneizado a magnitud momento, Mw, depurado de réplicas y premonitores y corregido por la falta de completitud para la estimación de tasas en diferentes rangos de magnitud; 3) la propuesta de un nueva zonificación sísmica, definiendo las zonas sismogenéticas en tres regímenes tectónicos: cortical, subducción interfase y subducción in-slab; 4) la caracterización sísmica de cada zona estimando los parámetros de recurrencia y Magnitud Máxima (Mmax), considerando para este último parámetro una distribución de valores posibles en función de la sismicidad y tectónica, tras un exhaustivo análisis de los datos existentes; 5) la generación de mapas de peligrosidad sísmica de Ecuador continental en términos de aceleración pico (PGA) y espectral SA (T= 1s) , en ambos casos para periodos de retorno (PR) de 475, 975 y 2475 años; 6) La estimación de espectros de peligrosidad uniforme (UHS) y sismos de control mediante desagregación de la peligrosidad, para PR de 475 y 2475 años en 4 capitales de provincia: Quito, Esmeraldas, Guayaquil y Loja. Una segunda parte del trabajo se destina al cálculo del riesgo sísmico en el Barrio Mariscal Sucre de Quito, lo que supone incidir ya a una escala municipal. Como principales contribuciones de este trabajo se destacan: 1) definición del escenario sísmico que más contribuye a la peligrosidad en Quito, que actuará como input de cálculo del riesgo; 2) caracterización de la acción sísmica asociada a ese escenario, incluyendo resultados de microzonación y efecto local en la zona de estudio; 3) Elaboración de una Base de Datos partiendo de información catastral e identificación de las tipologías dominantes; 4) Asignación de clases de vulnerabilidad y obtención de porcentajes de daño esperado en cada clase ante la acción sísmica definida previamente, con la consiguiente representación de mapas de vulnerabilidad y daño; 5) mapas de indicadores globales del riesgo sísmico; 6) Base de datos georreferenciada con toda la información generada en el estudio. Cabe destacar que el trabajo, aunque no formula nuevos métodos, si plantea una metodología integral de cálculo del riesgo sísmico, incorporando avances en cada fase abordada, desde la estimación de la peligrosidad o la definición de escenarios sísmicos con carácter hibrido (probabilista-determinista), hasta la asignación de vulnerabilidades y estimación de escenarios de daño. Esta tesis trata de presentar contribuciones hacia el mejor conocimiento de la peligrosidad sísmica en Ecuador y el riesgo sísmico en Quito, siendo uno de los primeros estudios de tesis que se desarrolla sobre estos temas en el país. El trabajo puede servir de ejemplo y punto de partida para estudios futuros; además de ser replicable en otras ciudades y municipios de Ecuador. -------------------- ABSTRACT: ------------------ This thesis first develops a study of seismic hazard in mainland Ecuador, following a zoned, probabilistic methodology. The study considers a regional scale and presents as main contributions: 1) The development of a State of Art on the Tectonics and Geology of Ecuador, concluding with the identification of the main seismic sources; 2) The creation of a Seismic Catalog project, collecting information from different agencies, which has been homogenized to Moment magnitude, Mw, purged from aftershocks and premonitories and corrected for the lack of completeness to estimate rates in different maggnitude ranges; 3) The proposal of a new seismic zoning, defining the seismogenic zones in three tectonic regimes: cortical, subduction interface and subduction in-slab; 4) The seismic characterization of each zone, estimating the parameters of recurrence and Maximum Magnitude (Mmax), considering the latter as a distribution of possible values, depending on the seismicity and tectonics, and after a thorough analysis of the existing data; 5) Seismic hazard maps of continental Ecuador in terms of peak ground acceleration (PGA) and spectral SA(T=1), and return periods (PR) of 475, 975 and 2475 years; 6) Uniform hazard spectra (UHS) and control earthquakes obtained by hazard disaggregation, for PR 475 and 2475 years in four provincial capitals: Quito, Esmeraldas, Guayaquil and Loja. The second section focuses on the calculation of seismic risk in the Quito Mariscal Sucre parish, which is already supposed to be influencing at a municipal level. The main contributions here are the: 1) Definition of the seismic scenario that contributes most to the hazard in Quito, which acts as an input in the risk calculation; 2) Characterization of the seismic action associated with that scenario, including results of micro-zoning and local effect in the study area; 3) Development of a database, based on cadastral data and identification of key typologies; 4) Allocation of vulnerability classes and obtaining percentages of damage expected in each class faced with the seismic action previously defined, with the consequent representation of maps of vulnerability and damage; 5) Global maps of seismic risk indicators; 6) Geo-referenced database with all the information generated in the study. It should be noted that although new methods are not prescribed, this study does set a comprehensive methodology for the calculation of seismic risk, incorporating advances in each phase approached, from the hazard estimation, or definition of seismic scenarios applying a hybrid (deterministic-probabilistic) method, to the allocation of vulnerabilities and estimation of damage scenarios. This thesis aims to present contributions leading to a better understanding of seismic hazard in Ecuador and seismic risk in Quito, and is one of the first studies in the country to develop such themes. This study can serve as an example and starting point for future studies, which could replicate this methodology in other cities and municipalities.

Scale dependence in earthquake phenomena and its relevance to earthquake prediction.

The recent discovery of a low-velocity, low-Q zone with a width of 50-200 m reaching to the top of the ductile part of the crust, by observations on seismic guided waves trapped in the fault zone of the Landers earthquake of 1992, and its identification with the shear zone inferred from the distribution of tension cracks observed on the surface support the existence of a characteristic scale length of the order of 100 m affecting various earthquake phenomena in southern California, as evidenced earlier by the kink in the magnitude-frequency relation at about M3, the constant corner frequency for earthquakes with M below about 3, and the sourcecontrolled fmax of 5-10 Hz for major earthquakes. The temporal correlation between coda Q-1 and the fractional rate of occurrence of earthquakes in the magnitude range 3-3.5, the geographical similarity of coda Q-1 and seismic velocity at a depth of 20 km, and the simultaneous change of coda Q-1 and conductivity at the lower crust support the hypotheses that coda Q-1 may represent the activity of creep fracture in the ductile part of the lithosphere occurring over cracks with a characteristic size of the order of 100 m. The existence of such a characteristic scale length cannot be consistent with the overall self-similarity of earthquakes unless we postulate a discrete hierarchy of such characteristic scale lengths. The discrete hierarchy of characteristic scale lengths is consistent with recently observed logarithmic periodicity in precursory seismicity.

Intermediate-term earthquake prediction.

An earthquake of magnitude M and linear source dimension L(M) is preceded within a few years by certain patterns of seismicity in the magnitude range down to about (M - 3) in an area of linear dimension about 5L-10L. Prediction algorithms based on such patterns may allow one to predict approximately 80% of strong earthquakes with alarms occupying altogether 20-30% of the time-space considered. An area of alarm can be narrowed down to 2L-3L when observations include lower magnitudes, down to about (M - 4). In spite of their limited accuracy, such predictions open a possibility to prevent considerable damage. The following findings may provide for further development of prediction methods: (i) long-range correlations in fault system dynamics and accordingly large size of the areas over which different observed fields could be averaged and analyzed jointly, (ii) specific symptoms of an approaching strong earthquake, (iii) the partial similarity of these symptoms worldwide, (iv) the fact that some of them are not Earth specific: we probably encountered in seismicity the symptoms of instability common for a wide class of nonlinear systems.

Implications of fault constitutive properties for earthquake prediction.

The rate- and state-dependent constitutive formulation for fault slip characterizes an exceptional variety of materials over a wide range of sliding conditions. This formulation provides a unified representation of diverse sliding phenomena including slip weakening over a characteristic sliding distance Dc, apparent fracture energy at a rupture front, time-dependent healing after rapid slip, and various other transient and slip rate effects. Laboratory observations and theoretical models both indicate that earthquake nucleation is accompanied by long intervals of accelerating slip. Strains from the nucleation process on buried faults generally could not be detected if laboratory values of Dc apply to faults in nature. However, scaling of Dc is presently an open question and the possibility exists that measurable premonitory creep may precede some earthquakes. Earthquake activity is modeled as a sequence of earthquake nucleation events. In this model, earthquake clustering arises from sensitivity of nucleation times to the stress changes induced by prior earthquakes. The model gives the characteristic Omori aftershock decay law and assigns physical interpretation to aftershock parameters. The seismicity formulation predicts large changes of earthquake probabilities result from stress changes. Two mechanisms for foreshocks are proposed that describe observed frequency of occurrence of foreshock-mainshock pairs by time and magnitude. With the first mechanism, foreshocks represent a manifestation of earthquake clustering in which the stress change at the time of the foreshock increases the probability of earthquakes at all magnitudes including the eventual mainshock. With the second model, accelerating fault slip on the mainshock nucleation zone triggers foreshocks.

Dynamic friction and the origin of the complexity of earthquake sources.

We study a simple antiplane fault of finite length embedded in a homogeneous isotropic elastic solid to understand the origin of seismic source heterogeneity in the presence of nonlinear rate- and state-dependent friction. All the mechanical properties of the medium and friction are assumed homogeneous. Friction includes a characteristic length that is longer than the grid size so that our models have a well-defined continuum limit. Starting from a heterogeneous initial stress distribution, we apply a slowly increasing uniform stress load far from the fault and we simulate the seismicity for a few 1000 events. The style of seismicity produced by this model is determined by a control parameter associated with the degree of rate dependence of friction. For classical friction models with rate-independent friction, no complexity appears and seismicity is perfectly periodic. For weakly rate-dependent friction, large ruptures are still periodic, but small seismicity becomes increasingly nonstationary. When friction is highly rate-dependent, seismicity becomes nonperiodic and ruptures of all sizes occur inside the fault. Highly rate-dependent friction destabilizes the healing process producing premature healing of slip and partial stress drop. Partial stress drop produces large variations in the state of stress that in turn produce earthquakes of different sizes. Similar results have been found by other authors using the Burridge and Knopoff model. We conjecture that all models in which static stress drop is only a fraction of the dynamic stress drop produce stress heterogeneity.

Geometric incompatibility in a fault system.

Interdependence between geometry of a fault system, its kinematics, and seismicity is investigated. Quantitative measure is introduced for inconsistency between a fixed configuration of faults and the slip rates on each fault. This measure, named geometric incompatibility (G), depicts summarily the instability near the fault junctions: their divergence or convergence ("unlocking" or "locking up") and accumulation of stress and deformations. Accordingly, the changes in G are connected with dynamics of seismicity. Apart from geometric incompatibility, we consider deviation K from well-known Saint Venant condition of kinematic compatibility. This deviation depicts summarily unaccounted stress and strain accumulation in the region and/or internal inconsistencies in a reconstruction of block- and fault system (its geometry and movements). The estimates of G and K provide a useful tool for bringing together the data on different types of movement in a fault system. An analog of Stokes formula is found that allows determination of the total values of G and K in a region from the data on its boundary. The phenomenon of geometric incompatibility implies that nucleation of strong earthquakes is to large extent controlled by processes near fault junctions. The junctions that have been locked up may act as transient asperities, and unlocked junctions may act as transient weakest links. Tentative estimates of K and G are made for each end of the Big Bend of the San Andreas fault system in Southern California. Recent strong earthquakes Landers (1992, M = 7.3) and Northridge (1994, M = 6.7) both reduced K but had opposite impact on G: Landers unlocked the area, whereas Northridge locked it up again.