Synthesis and application of stimuli responsive tunable systems based on physical interactions

Novel single step synthetic procedure for hydrophobically modified alkali soluble latexes (HASE) via a miniemulsion-analogous method is presented. This facile method simplifies the copolymerization of the monomers with basically “opposite” character in terms of their hydrophilic/hydrophobic nature, which represent one of the main challenges in water based systems. Considered systems do not represent classical miniemulsions due to a high content of water soluble monomers. However, the polymerization mechanism was found to be rather similar to miniemulsion polymerization process.rnThe influence of the different factors on the system stability has been investigated. The copolymerization behavior studies typically showed strong composition drifts during copolymerization. It was found that the copolymer composition drift can be suppressed via changing the initial monomer ratio.rnThe neutralization behavior of the obtained HASE systems was investigated via potentiometric titration. The rheological behavior of the obtained systems as a function of the different parameters, such as pH, composition (ultrahydrophobe content) and additive type and content has also been investigated.rnDetailed investigation of the storage and loss moduli, damping factor and the crossover frequencies of the samples showed that at the initial stages of the neutralization the systems show microgel-like behavior.rnThe dependence of the rheological properties on the content and the type of the ultrahydrophobe showed that the tuning of the mechanical properties can be easily achieved via minor (few percent) but significant changes in the content of the latter. Besides, changing the hydrophobicity of the ultrahydrophobe via increasing the carbon chain length represents another simple method for achieving the same results.rnThe influence of amphiphilic additives (especially alcohols) on the rheological behavior of the obtained systems has been studied. An analogy was made between micellation of surfactants and the formation of hydrophobic domains between hydrophobic groups of the polymer side chain.rnDilution induced viscosity reduction was investigated in different systems, without or with different amounts or types of the amphiphilic additive. Possibility of the controlled response to dilution was explored. It was concluded that the sensitivity towards dilution can be reduced, and in extreme cases even the increase of the dynamic modulus can be observed, which is of high importance for the setting behavior of the adhesive material.rnIn the last part of this work, the adhesive behavior of the obtained HASE systems was investigated on different substrates (polypropylene and glass) for the standard labeling paper. Wet tack and setting behavior was studied and the trends for possible applications have been evaluated.rnThe novel synthetic procedure, investigation of rheological properties and the possibility of the tuning via additives, investigated in this work create a firm background for the development of the HASE based adhesives as well as rheology modifiers with vast variety of possible applications due to ease of tuning the mechanical and rheological properties of the systems.

[Management of oxygen delivery and consumption during sepsis]

Maintaining an adequate tissue oxygen delivery (DO(2)) and consumption (VO(2)) is crucial in the treatment of septic patients. A fall in V0(2) is associated with a higher mortality. The early recognition of shock or tissue hypo perfusion impacts on patient prognosis. In occasions, hypovolemia or important regional oxygen debts are not recognized, since macro homodynamic variables have been compensated. In this situation, the use of metabolic hypo perfusion markers such as lactate, central venous oxygen saturation and gastric goniometry, can be helpful. However, interpretation of these markers should be cautious and always considering the overall clinical status of the patient. In the initial stages of sepsis, the dependency of V0(2) on DO(2) predominates as histopathological mechanism of multiple organic failure. In late stages, other factors predominate as determinants of multiple organic failure and mortality, such as hyper or hypo immune response, microcirculatory alterations and cytopathic hypoxia.

Examining the gateway to the limbic system with diffusion tensor imaging: the perforant pathway in dementia

Current treatments for Alzheimer's disease (AD) are only able to slow the progression of mental deterioration, making early and reliable diagnosis an essential part of any promising therapeutic strategy. In the initial stages of AD, the first neuropathological alterations occur in the perforant pathway (PP), a large neuronal fiber tract located at the entrance to the limbic system. However, to date, there is no sensitive diagnostic tool for performing in vivo assessments of this structure. In the present bimodal magnetic resonance imaging (MRI) study, we examined 10 elderly controls, 10 subjects suffering from mild cognitive impairment (MCI), and 10 AD patients in order to evaluate the sensitivity of diffusion tensor imaging (DTI), a new MRI technique, for detecting changes in the PP. Furthermore, the diagnostic explanatory power of DTI data of the PP should be compared to high-resolution MRI volumetry and intervoxel coherences (COH) of the hippocampus and the entorhinal cortex, two limbic regions also involved in the pathophysiology of early AD. DTI revealed a marked decrease in COH values in the PP region of MCI (right side: 26%, left side: 29%, as compared to controls) and AD patients (right side: 37%, left side: 43%, as compared to controls). Reductions in COH values of the PP region were significantly correlated with cognitive impairment. DTI data of the PP zone were the only parameter differing significantly between control subjects and MCI patients, while the volumetric measures and the COH values of the hippocampus and the entorhinal cortex did not. DTI of medial temporal brain regions is a promising non-invasive tool for the in vivo diagnosis of the early/preclinical stages of AD.

[Precancerous and high risk lesions of the oral mucosa--Diagnosis, therapy and follow-up in two cases]

Stomatologic lesions at risk to develop an oral squamous cell carcinoma (OSCC) such as oral leukoplakia, erythroplakia/erythroleukoplakia, or oral lichen planus, need an early detection, diagnosis and a long-term/lifelong follow-up to prevent malignant transformation. In the following report, two patients are presented with oral mucosal lesions, who were referred, diagnosed, treated, and underwent follow-up examinations at the Stomatology Service of the Department of Oral Surgery and Stomatology at the University of Bern. These two cases emphasize the importance of early detection and managment of precancerous lesions or initial stages of OSCC. Additionally, risk factors, such as tobacco and alcohol consumption and their influence on stomatologic lesions and their prognosis, will be discussed.

Photodegradation and photostabilization of weathered wood flour filled polyethylene composites

Wood plastic composites (WPCs) have gained popularity as building materials because of their usefulness in replacing solid wood in a variety of applications. These composites are promoted as being low-maintenance, high-durability products. However, it has been shown that WPCs exposed to weathering may experience a color change and/or loss in mechanical properties. An important requirement for building materials used in outdoor applications is the retention of their aesthetic qualities and mechanical properties during service life. Therefore, it is critical to understand the photodegradation mechanisms of WPCs exposed to UV radiation and to develop approaches to stabilize these composites (both unstabilized and stabilized) as well as the effect of weathering on the color fade and the retention of mechanical properties were characterized. Since different methods of manufacturing WPCs lead to different surface characteristics, which can influence weathering, the effect of manufacturing method on the photodegradation of WPCs was investigated first. Wood flour (WF) filled high-density polyethylene (HDPE) composite samples were either injection molded, extruded, or extruded and then planed. Fourier transform infrared (FTIR) spectroscopy was used to monitor the surface chemistry of the manufactured composites. The spectra showed that the surface of planed samples had more wood component than extruded and injection molded samples, respectively. After weathering, the samples were analyzed for color fade, and loss of flexural properties. The final lightness of the composites was not dependent upon the manufacturing method. However the mechanical property loss was dependent upon manufacturing method. The samples with more wood component at the surface (planed samples) experienced a larger percentage of total loss in flexural properties after weathering due to a greater effect of moisture on the samples. The change in surface chemistry of HDPE and WF/HDPE composites after weathering was studied using spectroscopic techniques. X-ray photoelectron spectroscopy (XPS) was used to characterize the occurrence of surface oxidation whereas FTIR spectroscopy was used to monitor the development of degradation products, such as carbonyl groups and vinyl groups, and to determine changes in HDPE crystallinity. Surface oxidation occurred immediately after exposure for both the neat HDPE and WF/HDPE composites. After weathering, the surface of the WF/HDPE composites was oxidized to a greater extent than the neat HDPE after weathering. This suggests that photodegradation is exacerbated by the addition of the carbonyl functional groups of the wood fibers within the HDPE atrix during composite manufacturing. While neat HDPE may undergo cross-linking in the initial stages of accelerated weathering, the WF may physically hinder the ability of the HDPE to cross-link resulting in the potential for HDPE chain scission to dominate in the initial weathering stages of the WF/HDPE composites. To determine which photostabilizers are most effective for WF/HDPE composites, factorial experimental designes were used to determine the effects of adding two hindered amine light stabilizers, an ultraviolet absorber, and a pigment on the color made and mechanical properties of both unweathered and UV weathered samples. Both the pigment and ultraviolet absorber were more effective photostabilizers for WF/HDPE composites than hinder amine light stabilizers. The ineffectiveness of hindered amine light stabilizers in protecting WPCs against UV radiation was attribuated to the acid/base reactions occurring between the WF and hindered amine light stabilizer. The efficiency of an ultraviolet absorber and/or pigment was also examined by incorporating different concentration of an ultraviolet absorber and/or pigment into WF/HDPE composites. Color change and flexural properties were determined after accelerated UV weathering. The lightness of the composite after weathering was influenced by the concentration of both the ultraviolet absorber by masking the bleaching wood component as well as blocking UV light. Flexural MOE loss was influenced by an increase in ultraviolet absorber concentration, but increasing pigment concentration from 1 to 2% had little influence on MOE loss. However, increasing both ultraviolet absorber and pigment concentration resulted in improved strength properties over the unstabilized composites after 3000 h of weather. Finally, the change in surface chemistry due to weathering of WF/HDPE composites that were either unstabilized or stabilized with an ultraviolet absorber and/or pigment was analyzed using FTIR spectroscopy. The samples were tested for loss in modulus of elasticity, carbonyl and vinyl group formation at the surface, and change in HDPE crystallinity. It was concluded that structural changes in the samples; carbonyl group formation, terminal vinyl group formation, and crystallinity changes cannot reliably be used to predict changes in modulus of elasticity using a simple linear relationship. The effect of cross-linking, chain scission, and crystallinity changes due to ultraviolet exposure as well as the interfacial degradation due to moisture exposure are inter-related factors when weathering HDPE and WF/HDPE composites.

Mammalian pre-mRNA 3' end processing factor CF I m 68 functions in mRNA export

Export of mRNA from the nucleus is linked to proper processing and packaging into ribonucleoprotein complexes. Although several observations indicate a coupling between mRNA 3' end formation and export, it is not known how these two processes are mechanistically connected. Here, we show that a subunit of the mammalian pre-mRNA 3' end processing complex, CF I(m)68, stimulates mRNA export. CF I(m)68 shuttles between the nucleus and the cytoplasm in a transcription-dependent manner and interacts with the mRNA export receptor NXF1/TAP. Consistent with the idea that CF I(m)68 may act as a novel adaptor for NXF1/TAP, we show that CF I(m)68 promotes the export of a reporter mRNA as well as of endogenous mRNAs, whereas silencing by RNAi results in the accumulation of mRNAs in the nucleus. Moreover, CF I(m)68 associates with 80S ribosomes but not polysomes, suggesting that it is part of the mRNP that is remodeled in the cytoplasm during the initial stages of translation. These results reveal a novel function for the pre-mRNA 3' end processing factor CF I(m)68 in mRNA export.

E-Learning Systems, Environments and Approaches

The volume consists of twenty-five chapters selected from among peer-reviewed papers presented at the CELDA (Cognition and Exploratory Learning in the Digital Age) 2013 Conference held in Fort Worth, Texas, USA, in October 2013 and also from world class scholars in e-learning systems, environments and approaches. The following sub-topics are included: Exploratory Learning Technologies (Part I), e-Learning social web design (Part II), Learner communities through e-Learning implementations (Part III), Collaborative and student-centered e-Learning design (Part IV). E-Learning has been, since its initial stages, a synonym for flexibility. While this dynamic nature has mainly been associated with time and space it is safe to argue that currently it embraces other aspects such as the learners’ profile, the scope of subjects that can be taught electronically and the technology it employs. New technologies also widen the range of activities and skills developed in e-Learning. Electronic learning environments have evolved past the exclusive delivery of knowledge. Technology has endowed e-Learning with the possibility of remotely fomenting problem solving skills, critical thinking and team work, by investing in information exchange, collaboration, personalisation and community building.

Successful Careers in Football – Findings of a Person-Oriented Study

A successful career in football is the result of the appropriate interaction between different aspects of an individual’s life, since the various areas and phases of one’s life depend on each other. An endogenous causal relationship exists throughout a person’s entire history (Mayer, 1990). In particular, their family, work and sports career must be tuned to each other. The transition from the initial stages of education (compulsory schooling) to vocational training, which coincides with the beginning of the selection for the national youth teams, is a particularly critical phase (Wylleman, Theeboom, & Lavallee, 2004). In order to do justice to the overall life situation of a young sports talent during this transition phase, we have adopted a holistic perspective and follow Bergman, Magnusson and El-Khouri (2003) in using a person-oriented and systemic approach. In doing so, our main focus lies on the person-environment system. This overall system is made up of various subsystems, consisting of several operating factors which interact with one another. The different levels to which these operating factors are expressed lead to observable patterns, which can be summarised in the form of types. Particularly promising types can therefore be identified and the developmental process can be described. Former players on the Swiss U16 to U21 national football teams, born between 1981 and 1987 (n=159), were interviewed concerning their careers, and the operating factors school/vocational training, family support and sports environment were examined. With the help of the LICUR method (Linking of Clusters after removal of Residue) (Bergman et al., 2003), developmental types were identified which were promising in terms of achieving top performance in adulthood. A range of developmental types and anti-types emerge for the transition from the under-15 phase to the over-16 phase. One particularly promising type is observed in the over-16 phase, for which the operating factors education, family support and participation in national U16 to U18 teams have slightly above-average scores, with scores that are well above average in the sports environment.

The effects of population density on the spread of disease

The objective of this study is to identify the relationship between population density and the initial stages of the spread of disease in a local population. This study proposes to concentrate on the question of how population density affects the distribution of the susceptible individuals in a local population and thus affects the spread of the disease, measles. Population density is measured by the average of the number of contacts with susceptible individuals by each individual in the population during a fixed-length time period. The term “contact with susceptible individuals” means sufficient contact between two people for the disease to pass from an infectious person to a susceptible person. The fixed-length time period is taken to be the average length of time an infected person is infectious without symptoms of the disease. For this study of measles, the time period will be seven days. ^ While much attention has been given to modeling the entire epidemic process of measles, attempts have not been made to study the characteristics of contact rates required to initiate an epidemic. This study explores the relationship between population density, given a specific herd immunity rate in the population, and initial rate of the spread of the disease by considering the underlying distribution of contacts with susceptibles by the individuals in the population. ^ This study does not seek to model an entire measles epidemic, but to model the above stated relationship for the local population within which the first infective person is introduced. This study describes the mathematical relationship between population density parameters and contact distribution parameters. ^ The results are displayed in graphs that show the effects of different population densities on the spread of disease. The results support the idea that the number of new infectives is strongly related to the distribution of susceptible contacts. The results also show large differences in the epidemic measures between populations with densities equal to four versus three. ^

Assessing the Environmental Hazard of Using Seawater for Ore Processing at the Lasail Mine Site in the Sultanate of Oman

The Lasail mining area (Sultanate of Oman) was contaminated by acid mine drainage during the exploitation and processing of local and imported copper ore and the subsequent deposition of sulphide-bearing waste material into an unsealed tailings dump. In this arid environment, the use of seawater in the initial stages of ore processing caused saline contamination of the fresh groundwater downstream of the tailings dump. After detection of the contamination in the 1980s, different source-controlled remediation activities were conducted including a seepage water collection system and, in 2005, surface sealing of the tailings dump using an HDPE-liner to prevent further infiltration of meteoric water. We have been assessing the benefits of the remediation actions undertaken so far. We present chemical and isotopic (δ18O, δ 2H, 3H) groundwater data from a long-term survey (8–16 years) of the Wadi Suq aquifer along a 28 km profile from the tailings dump to the Gulf of Oman. Over this period, most metal concentrations in the Wadi Suq groundwater decreased below detection limits. In addition, in the first boreholes downstream of the tailings pond, the salinity contamination has decreased by 30 % since 2005. This decrease appears to be related to the surface coverage of the tailings pond, which reduces flushing of the tailings by the sporadic, but commonly heavy, precipitation events. Despite generally low metal concentrations and the decreased salinity, groundwater quality still does not meet the WHO drinking water guidelines in more than 90 % of the Wadi Suq aquifer area. The observations show that under arid conditions, use of seawater for ore processing or any other industrial activity has the potential to contaminate aquifers for decades.

Bank Performance: Market Power or Efficient Structure?

Regulatory change not seen since the Great Depression swept the U.S. banking industry beginning in the early 1980s, culminating with the Interstate Banking and Branching Efficiency Act of 1994. Significant consolidations have occurred in the banking industry. This paper considers the market-power versus the efficient-structure theories of the positive correlation between banking concentration and performance on a state-by-state basis. Temporal causality tests imply that bank concentration leads bank profitability, supporting the market-power, rather than the efficient-structure, theory of that positive correlation. Our finding suggests that bank regulators, by focusing on local banking markets, missed the initial stages of an important structural change at the state level.

Improving care of women at risk of unsafe abortion: implementing a risk-reduction model at the Uruguayan-Brazilian border

OBJECTIVE: To describe the initial stages of the implementation of a risk-reduction model designed by Iniciativas Sanitarias to shield women from unsafe abortion in a traditional community on the Uruguay-Brazil border. METHODS: This mixed-design study was conducted first between 22 and 26 March 2010, and then between 2 and 7 May 2011, in Rivera, Uruguay, to gather information from women seen at health centers, healthcare providers, and local policy makers before the project started and midway through the project. RESULTS: At baseline most women and providers considered abortion justifiable only on narrow grounds, yet favored the implementation of a risk-reduction model that would include preabortion as well as postabortion counseling, the former providing information on different abortion methods and their risks. By the midterm assessment, the counseling service had assisted 87 women with unwanted pregnancies. Of the 52 who came for a postabortion visit, 50 had self-administered misoprostol, with no complications. Women were highly satisfied with the counseling. At baseline, misoprostol seemed to be available from both pharmacists and informal sellers. At midterm, it was still available from informal vendors but pharmacists said they did not provide misoprostol. The risk-reduction initiative heightened public attention to the abortion issue but the controversy it generated did not seriously impede its implementation. CONCLUSION: It is feasible to implement the proposed risk-reduction model in a traditional community such as Rivera, not only in Uruguay but in any country irrespective of its abortion laws.