Environmental formaldehyde analysis by active diffusive sampling with a bundle of polypropylene porous capillaries followed by capillary zone electrophoretic separation and contactless conductivity detection

Compared to other volatile carbonylic compounds present in outdoor air, formaldehyde (CH2O) is the most toxic, deserving more attention in terms of indoor and outdoor air quality legislation and control. The analytical determination of CH2O in air still presents challenges due to the low-level concentration (in the sub-ppb range) and its variation with sampling site and time. Of the many available analytical methods for carbonylic compounds, the most widespread one is the time consuming collection in cartridges impregnated with 2,4-dinitrophenylhydrazine followed by the analysis of the formed hydrazones by HPLC. The present work proposes the use of polypropylene hollow porous capillary fibers to achieve efficient CH2O collection. The Oxyphan (R) fiber (designed for blood oxygenation) was chosen for this purpose because it presents good mechanical resistance, high density of very fine pores and high ratio of collection area to volume of the acceptor fluid in the tube, all favorable for the development of air sampling apparatus. The collector device consists of a Teflon pipe inside of which a bundle of polypropylene microporous capillary membranes was introduced. While the acceptor passes at a low flow rate through the capillaries, the sampled air circulates around the fibers, impelled by a low flow membrane pump (of the type used for aquariums ventilation). The coupling of this sampling technique with the selective and quantitative determination of CH2O, in the form of hydroxymethanesulfonate (HMS) after derivatization with HSO3-, by capillary electrophoresis with capacitively coupled contactless conductivity detection (CE-(CD)-D-4) enabled the development of a complete analytical protocol for the CH2O evaluation in air. (C) 2008 Published by Elsevier B.V.

Soda-Treated Sisal/Polypropylene Composites

Treated sisal fibers were used as reinforcement of polypropylene (PP) composites, with maleic anhydride-grafted PP (MAPP) as coupling agent. The composites were made by melting processing of PP with the fiber in a heated roller followed by multiple extrusions in a single-screw extruder. Injection molded specimens were produced for the characterization of the material. In order to improve the adhesion between fiber and matrix and to eliminate odorous substances, sisal fibers were treated with boiling water and with NaOH solutions at 3 and 10 wt.%. The mechanical properties of the composites were assessed by tensile, bend and impact tests. Additionally, the morphology of the composites and the adhesion at he fiber-matrix interface were analyzed by SEM. The fiber treatment led to very light and odorless materials, with yields of 95, 74 and 62 wt.% for treatments with hot water, 3 and 10 wt.% soda solution respectively. Fiber treatment caused an appreciable change in fiber characteristics, yet the mechanical properties under tensile and flexural tests were not influenced by that treatment. Only the impact strength increased in the composites with alkali-treated sisal fibers.

Mechanical, thermal and morphological characterization of polypropylene/biodegradable polyester blends with additives

The (bio)degradation of polyolefins can be accelerated by modifying the level of crystallinity or by incorporation of carbonyl groups by adding pro-oxidants to masterbatches or through exposure to ultraviolet irradiation. In this work we sought to improve the degradation of PP by adding cobalt, calcium or magnesium stearate to Ecoflex(R), PP or Ecoflex(R)/PP blends. The effect of the pro-oxidants on biodegradability was assessed by examining the mechanical properties and fluidity of the polymers. PP had higher values for tensile strength at break and Young`s modulus than Ecoflex(R), and the latter had little influence on the properties of PP in Ecoflex(R)/PP blends. However, the presence of pro-oxidants (except for calcium) reduced these properties. All of the pro-oxidants enhanced the fluidity of PP, a phenomenon that facilitated polymer degradation at high temperatures. (C) 2009 Elsevier Ltd. All rights reserved.

Evaluation of surface treatment techniques for polypropylene andimplementation of a method for testing ink adhesion

If a plastic material is used as a print bearer there are a need of a special surface treatment to get agod and durable printing. The most used surface treatment technique for the moment is coronatreatment. This kind of treatment has unfortunately showed not to be so durable in the long term.Plasma treatment which in this case uses different kind of gases in the treatment of polypropyleneis shown as a more effective treatment in this project. When the plasma treated surface has beenprinted is the good quality last much longer and the adhesion between the ink and the surface isremained. To test this adhesion is for the moment a standard used (ASTM D3359). This standardhas appeared unstable and dependent at many different factors, which gives a big variation in thetest results. Because of this has new test methods been carried out to give a more even and morereliable result in the test of the adhesion.

Bleaching and dyeing of superfine wool powder/polypropylene blend film

Fibers based regenerated protein draw much attention for recycling discarded protein resources and can produce biodegradable and environmental friendly polymers. In this study, superfine wool powder is blended with polypropylene (PP) to produce wool powder/PP blend film through extrusion and hot-pressing. Hydrogen peroxide is used to bleach the black colored surface of the blend films. The effects of peroxide concentration, bleaching time and powder content on the final whiteness and mechanical properties of the blend films are investigated.

The bleached films are dyed with acid red dyes and the dyed color is evaluated using a Computer Color Matching System. Color characters of dyed films, such as L*, a*, b*, ΔE*ab, C*ab and K/S values are measured and analyzed. The study not only reuses discarded wool resources into organic powder, widens the application of superfine wool powder on polymers, but also improves the dyeing properties of PP through the addition of protein content.

Improvement in mechanical properties of aluminum polypropylene composite fiber

Aluminum particles (Al) were added to polypropylene (PP) in the presence of poly ethylene glycol (PEG) and polypropylene-graft-maleic anhydride to produce composites. The composites were then melt-spun into a mono filament and tested for tensile properties, diameter evenness and morphology. Melt rheological properties of Al/PP composites were studied in linear viscoelastic response regions. It was observed that level of dispersion of aluminum particles within a polypropylene composite fiber could be improved by incorporating polyethylene glycol. The improvement of dispersion led to an improvement in the fibers mechanical properties through a reduction of the coefficient of variation of fiber diameter.

Exploring molecular changes at the surface of polypropylene after accelerated thermomolecular adhesion treatments

A central composite rotatable design (CCRD) method was used to investigate the performance of the accelerated thermomolecular adhesion process (ATmaP), at different operating conditions. ATmaP is a modified flame-treatment process that features the injection of a coupling agent into the flame to impart a tailored molecular surface chemistry on the work piece. In this study, the surface properties of treated polypropylene were evaluated using X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). All samples showed a significant increase in the relative concentration of oxygen (up to 12.2%) and nitrogen (up to 2.4%) at the surface in comparison with the untreated sample (0.7% oxygen and no detectable nitrogen) as measured by XPS. ToF-SIMS and principal components analysis (PCA) showed that ATmaP induced multiple reactions at the polypropylene surface such as chain scission, oxidation, nitration, condensation, and molecular loss, as indicated by changes in the relative intensities of the hydrocarbon (C₃H₇⁺ , C₃H₅⁺ , C₄H₇⁺, and C₅H₉⁺), nitrogen and oxygen-containing secondary ions (C₂H₃O⁺, C₃H₈N⁺, C₂H₅NO⁺, C₃H₆NO⁺, and C₃H₇NO⁺). The increase in relative intensity of the nitrogen oxide ions (C₂H₅NO⁺ and C₃H₇NO⁺) correlates with the process of incorporating oxides of nitrogen into the surface as a result of the injection of the ATmaP coupling agent.

Utilizing polypropylene fibers to improve physical and mechanical properties of concrete

The influence of polypropylene fibers has been studied in different proportioning and fiber aspect ratios to improve physical and mechanical properties of fiber-reinforced concretes. Fibers are used in two different lengths (12 mm and 19 mm) and proportions (0.1% and 0.3%) in concrete mixture design. Hardened concrete properties, such as 7- and 28-day compressive strength, splitting tensile strength, flexural strength, water and air absorption, and restrained shrinkage cracking were evaluated.

No statistically significant effects were observed for polypropylene fibers on the compressive strength of concrete, while toughness indexes, splitting tensile and flexural strength and durability parameters showed an increase in the presence of polypropylene fibers. Increased fiber availability (fiber aspect ratio) in the concrete matrix, in addition to the ability of longer polypropylene fibers to bridge on the micro cracks, are suggested as the reasons for the enhancement in mechanical properties. Finally, crack width in fiber-reinforced concrete is calculated analytically with fiber property variables (fiber type, length, diameter and proportion). Results are compared with experimental values and concluded that with an increase in fiber length and/or decrease in fiber diameter crack width, decrease significantly.