Material Growth and Device Fabrication of GaAs Based 1.3μm GaInNAs Quantum Well Laser Diodes

Material growth and device fabrication of the first 1.3μm quantum well （QW） edge emitting laser diodes in China are reported. Through the optimization of the molecular beam epitaxy （MBE） growth conditions and the tuning of the indium and nitrogen composition of the GalnNAs QWs, the emission wavelengths of the QWs can be tuned to 1.3μm. Ridge geometry waveguide laser diodes are fabricated. The lasing wavelength is 1.3μm under continuous current injection at room temperature with threshold current of 1kA/cm^2 for the laser diode structures with the cleaved facet mirrors. The output light power over 30mW is obtained.

High performance 1.55 mu m InGaAsP/InP strained layer quantum well laser diodes fabricated by MOCVD overgrowth method

High performance uncooled 1.55 mu m InGaAsP/InP strained layer quantum well (SL-QW) lasers grown by low pressure metal organic chemical vapor deposition (LP-MOCVD) were reported in this paper. Whole MOCVD over growth method were applied in this work. The threshold currents of 5mA and the highest lasing temperature of 122 degrees C were obtained.

Void swelling in MA956 ODS steel irradiated with 122 MeV Ne-ions at elevated temperatures

An investigation of a commercial oxide dispersion-strengthened steel (MA9561) irradiated with high energy Ne-ions to high doses at elevated temperatures is presented. Specimens of MA956 oxide dispersion strengthened steel together with a 9% Cr ferritic/martensitic steel, e.g., Grade 92 steel were irradiated simultaneously with 20Ne-ions (with 122 MeV) to successively increasing damage levels of 1, 5 and 10 dpa at the damage peak at 440 C and 570 C, respectively. Cross-sectional microstructures of the specimens were investigated with transmission electron microscopy. MA956 oxide dispersion strengthened steel showed a higher resistance to void swelling especially to void growth at the grain boundaries than the ferritic/martensitic steel, e.g., Grade 92 steel did, and thus exhibited a prominence for an application in the situation of a high He production at high temperatures. The suppression of the growth of voids especially at the grain boundaries in MA956 is ascribed to an enhanced recombination of the point defects and a trapping of Ne atoms at the interfaces of the yttrium–aluminum oxide particles and the matrix.

MEASUREMENT OF THE PROTON-PROTON CORRELATION FUNCTION FROM THE BREAK-UP OF Mg-22 AND Ne-20

An experiment of Mg-22 and Ne-20 beams bombarding on a C-12 target at an energy of 60 similar to 70 A MeV has been performed at the RIKEN projectile fragment separator (RIPS)in the RIKEN Ring Cyclotron Facility to study the two-proton correlated emission from Mg-22 and Ne-20 excited states. The two-protons momentum correlation functions have been obtained for Mg-22 and Ne-20, respectively. The trajectories of the Mg-22 decayed products (Ne-20 + p + p) were also measured to get the angular correlations between the two protons in Center of Mass of decaying system by relativistic-kinematics reconstruction. The results exhibit that Mg-22 has the features of He-2 cluster decay mechanism.

Degradation of polyimide induced by nitrogen laser irradiation

The degradation behavior of polyimide (PMDA-ODA) induced by nitrogen laser irradiation was studied. The changes in the surface morphology and the composition of the irradiated polyimide films were examined by scanning electron microscopy, X-ray photoelectron spectroscopy and FT-IR spectroscopy. The initial reaction was achieved by photochemical degradation of polyimide in the highly electronic excited state by the absorption of a second 337 nm photon. Atmospheric oxygen sequentially reacted with the produced radicals to form a highly oxidized layer. The formation of carbonyl group was enhanced by the heat remaining on the irradiated polyimide film surfaces. (C) 2000 Elsevier Science B.V. All rights reserved.

Monte Carlo simulation of pulsed-laser polymerization in emulsion

The pulsed-laser polymerization in emulsions has been simulated by the Monte Carlo method. Our simulation shows that the best measure of the propagation rate coefficients K-p is the peak maximum of molecular weight distribution for microemulsions when the droplets are small. However, the inflection point at the low-molecular-weight side of the peaks provides the best measure of K-p of bigger droplets. (C) 2000 Elsevier Science Ltd. All rights reserved.

Excimer-laser irradiated polyimide films as temperature-sensitive materials

The temperature dependence of the resistivity of KrF laser irradiated polyimide films was studied. In all cases, the resistivity decreased with increasing temperature. The irradiated polyimide film exhibited a typical semiconducting property. This result indicated that the irradiated polyimide films can be used as temperature-sensitive materials. We demonstrated that both the sensitivity and the sensitive temperature range of the irradiated polyimide films can be altered by adjusting laser irradiation parameters. The intrinsic relationship between the temperature coefficient of the resistivity and irradiation condition was interpreted in terms of the microstructural change. The result provided a new insight into the fundamental aspects of laser irradiated polyimide film structure and a method of preparing temperature-sensitive materials. (C) 2000 Elsevier Science B.V. All rights reserved.

Formation of conducting layers on excimer-laser-irradiated polyimide film surfaces

Conducting layers on KrF excimer-laser-irradiated polyimide film surfaces were investigated by XPS, SEM and Fourier transform infrared (FTIR)-Raman spectroscopy, Analysis of polyimide residue after laser irradiation provided valuable insight into the nature of the formation of conducting layers. The subtle different between KrF laser irradiation and the pyrolysis of polyimide was found by comparison of the formation process of conducting layers. A physical picture was presented to describe better the formation of conducting layers. Under KrF laser irradiation, polyimide films underwent thermal decomposition assisted by photoinduced direct bond breaking. Polycrystalline graphite was subsequently formed as the product of the secondary addition reaction of carbon-enriched clusters, Such reaction was supported by the remaining energy on the irradiated polyimide film surface. This result shows that the thermal process played an important role that was not just restricted to the formation of conducting layers, Copyright (C) 2000 John Wiley & Sons, Ltd.

Thermal influence on excimer-laser-induced electrical conductivity on polyimide film surfaces

The thermal influence on the electrical conductivity of polyimide film surfaces induced by KrF-laser irradiation was investigated, The formation of conducting phases was demonstrated to be highly temperature sensitive, as evidenced by strong dependence of the electrical conductivity on repetition rate and ambient temperature. XPS and Raman studies showed that the efficiency of the formation of conducting phases could be enhanced by the increase of temperature on irradiated polyimide film surfaces. After the disruption of polymeric chain, the carbon-enriched clusters remained on the irradiated polyimide film surfaces organized into polycrystalline graphite-like clusters responsible for electrical conductivity. The resulting dangling bonds from the decomposition process of polyimide acted as centers for the rearrangement of carbon-enriched clusters. It is suggested that the motion of radicals was promoted with increasing the temperature. Therefore the formation of polycrystalline graphite-like clusters benefited from high remaining temperature on the irradiated polyimide film surfaces. These results revealed that thermal influence played a dominant role on the formation of conducting phases.

Structural studies of excimer laser-induced percolative phase transition on polyimide thin film surfaces

The behavior of electrical conductivity for excimer laser irradiated polyimide films in the vicinity of the critical number of laser shots was described by three-dimensional percolative phase transition model. It is: found that electrical conductivity changed more rapidly than that predicted by the percolation model. Thus, the change in microstructure with increasing number of laser shots was analyzed by FT-IR Raman spectrometry and laser desorption time-of-flight mass spectrometry. It is demonstrated that not only the number but also the average size of graphite particles on the irradiated polyimide film surfaces increased with increasing number of laser shots. These results were helpful to better understand the critical change in electrical conductivity on the irradiated polyimide film surfaces. (C) 2001 Elsevier Science B.V. All rights reserved.