Gas-metal reactions and porosity in the inert gas arc welding of copper

A study has been made of the effects of welding and material variables on the occurrence of porosity in tungsten inert gas arc welding of copper. The experiments were based on a statistical design and variables included, welding current, welding speed, arc atmosphere composition, inert gas flow rate, weld preparation, and base material. The extent of weld metal porosity was assessed by density measurement and its morphology by X-ray radiography and metallography. In conjunction with this the copper-steam reaction has been investigated under conditions of controlled atmosphere arc melting. The welding experiments have shown that the extent of steam porosity is increased by increased water vapour content of the arc atmosphere, increased oxygen content of the base material and decreased welding speed. The arc melting experiments have shown that the steam reaction occurs in the body of the weld pool and proceeds to an apparent equi1ibrium state appropriate to to its temperature, the hydrogen and oxygen being supplied by the dissociation of water vapour in the arc atmosphere. It has been shown conclusively that nitrogen porosity can occur in the tungsten inert gas arc welding of copper and that this porosity can be eliminated by using filler wires containing small amounts of aluminum and titanium. Since it has been shown to be much more difficult to produce sound butt welds than melt runs it has been concluded that the porosity associated with joint fit up is due to nitrogen entrained into tho arc atmosphere. Clearly atmospheric entrainment would also, to a much lesser extent, involve water vapour. From a practical welding point of view it has thus been postulated that use of a filler wire containing small amounts of aluminum and/or titanium would eliminate both forms of porosity since these elements are both strongJy deoxidising and denitriding.

Ultrasonic inspection of austenitic stainless steel weldments

Ultrasonic waves interact in a complex manner with the metallurgical structure of austenitic weldments resulting in ambiguity when interpreting reflections and at times in misinterpretation of defect positions. In this work, current knowledge of the structure of austenitic welds is outlined, and the influence of this structure on the propagation of ultrasonic waves is reviewed. Using an established and highly accurate technique, data on velocity variations as a function of the angle between the direction of soundwave propagation and the axes of preferred grain orientation existing in such welds, are experimentally obtained. These results and existing theory are used to provide quantitative evidence of (i) anisotropy factors in austenitic welds, (ii) beam skewing effects for different wave modes and polarizations, and (iii) the extent of acoustic impedance mismatch between parent and weld metals. The existence of "false" indications is demonstrated, and suggestions are made into their nature. The effectiveness of conventional transverse wave techniques for inspecting artificial and real defects existing in austenitic weldments is experimentally investigated, the limitations are demonstrated, and possible solutions are proposed. The possibilities offered by the use of longitudinal angle probes for ultrasonic inspection of real and artificial defects existing in austenitic weldments are experimentally investigated, and parameters such as probe angle, frequency and scanning position are evaluated. Detailed work has been carried out on the interaction of ultrasound with fatigue and corrosion-fatigue cracks in the weld metal and the heat affected zones (HAZs) of 316 and 347 types of austenitic weldments, together with the influence of elastic compressive stresses, defect topography and defect geometry. Practical applications of all results are discussed, and more effective means of ultrasonic inspection of austenitic weldments are suggested.

Deformation and failure of welded steels used in offshore constructions

Hydrocarbons are the most common form of energy used to date. The activities involving exploration and exploitation of large oil and gas fields are constantly in operation and have extended to such hostile environments as the North Sea. This enforces much greater demands on the materials which are used, and the need for enhancing the endurance of the existing ones which must continue parallel to the explorations. Due to their ease in fabrication, relatively high mechanical properties and low costs, steels are the most widely favoured material for the construction of offshore platforms. The most critical part of an offshore structure prone to failure are the welded nodal joints, particulary those which are used within the vicinity of the splash zones. This is an area of high complex stress concentrations, varying mechanical and metallurgical properties in addition to severe North Sea environmental conditions. The main are of this work has been concerned with the durability studies of this type of steel, based on the concept of the worst case analysis, consisting of combinations of welds of varying qualities, various degrees of stress concentrations and the environmental conditions of stress corrosion and hydrogen embrittlement. The experiments have been designed to reveal significance of defects as sites of crack initiation in the welded steels and the extent to which stress corrosion and hydrogen embrittlement will limit their durability. This has been done for various heat treatments and in some experiments deformation has been forced through the welded zone of the specimens to reveal the mechanical properties of the welds themselves to provide data for finite element simulations. A comparison of the results of these simulations with the actual deformation and fracture behaviour has been done to reveal the extent to which both mechanical and metallurgical factors control behaviour of the steels in the hostile environments of high stress, corrosion, and hydrogen embrittlement at their surface.

Fatigue cracking from stress concentration in mild steel

Pulsating; tension fatigue tests have been carried out on edge notched specimens of a mild steel. An electrical potential drop technique was used to determine the number of cycles taken to initiate cracks and the rate at which the cracks grew across the specimen. The results could be described by the range of stress intensity factor, which for crack initiation was modified to take account of the notch root radius. Analysis of elastic stress distributions at cracks and notches and models of plasticity at crack tips are used to discuss the results. Limited evidence in the literature indicates that the fracture mechanics approach may provide a general description of crack initiation and growth in notched specimens, and a simple graphical method of calculating fatigue lives is described. The results are used to illustrate the effects of specimen size and geometry on the fatigue life of notched specimens. The relevance of the work to the assessment of the significance of defects in welds is discussed.

On Graph-Based Cryptography and Symbolic Computations

We have been investigating the cryptographical properties of in nite families of simple graphs of large girth with the special colouring of vertices during the last 10 years. Such families can be used for the development of cryptographical algorithms (on symmetric or public key modes) and turbocodes in error correction theory. Only few families of simple graphs of large unbounded girth and arbitrarily large degree are known. The paper is devoted to the more general theory of directed graphs of large girth and their cryptographical applications. It contains new explicit algebraic constructions of in finite families of such graphs. We show that they can be used for the implementation of secure and very fast symmetric encryption algorithms. The symbolic computations technique allow us to create a public key mode for the encryption scheme based on algebraic graphs.

The application of laser welding on Left Ventricular Assist Device (LVAD)

A successful and useful treatment for end-stage heart failure is Left ventricular assist device (LVAD). An important part - a hydrodynamically suspended impeller exposed to corrosive conditions, required to sealed hermetically into micro packages. Laser beam welded (LBW) Ti6Al4V alloy has been adopted in anti-corrosion micro packages for the impeller of a (LVAD). Thin and narrow welds were required for such medical equipment. Pulsed Nd:YAG welding was successfully adopted as sealing method for the impeller. ©2011 IEEE.

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Avaliação da soldagem GMAW mecanizada e automatizada para união de dutos utilizando fontes convencional e com controle de curto- circuito

Welding is one of the most employed process for joining steel pipes. Although, manual welding is still the most used one, mechanized version and even automatized one have increased its demand. Thus, this work deals with girth welding of API 5L X65 pipes with 8” of nominal diameter and 8.0 mm thickness, beveled with V-30º narrow gap. Torch is moved by a bug carrier (mechanized welding) and further the parameters are controlled as a function of angular position (automatized welding). Welding parameters are presented for filling the joint with two-passes (root and filling/capping passes). Parameters for the root pass were extracted from previous author´s work with weldments carried out in plates, but validated in this work for pipe welding. GMAW processes were assessed with short-circuit metal transfer in both conventional and derivative modes using different technologies (RMD, STT and CMT). After the parameter determination, mechanical testing was performed for welding qualification (uniaxial tension, face and root bending, nick break, Charpy V-notch impact, microhardness and macrograph). The initially obtained results for RMD and CMT were acceptable for all testing and, in a second moment, also for the STT. However, weld beads carried out by using the conventional process failed and revealed the existence of lack of fusion, which required further parametrization. Thus, a Parameter-Variation System for Girth Welding (SVP) was designed and built to allow varying the welding parameters as a function of angular position by using an inclinometer. The parameters were set for each of the three angular positions (flat, vertical downhill and overhead). By using such equipment and approach, the conventional process with parameter variation allowed reducing the welding time for joint accomplishment of the order of 38% for the root pass and 30% for the filling/capping pass.

Body measurements and blood plasma lipid, PCB and OH-PCB content of polar bear (U. maritimus) mothers and cubs, Svalbard

The aim of this study was to examine the plasma concentrations and prevalence of polychlorinated biphenyls (PCBs) and hydroxylated PCB-metabolites (OH-PCBs) in polar bear (Ursus maritimus) mothers (n = 26) and their 4 months old cubs-of-the-year (n = 38) from Svalbard to gain insight into the mother-cub transfer, biotransformation and to evaluate the health risk associated with the exposure to these contaminants. As samplings were performed in 1997/1998 and 2008, we further investigated the differences in levels and pattern of PCBs between the two sampling years. The plasma concentrations of Sum(21)PCBs (1997/1998: 5710 ± 3090 ng/g lipid weight [lw], 2008: 2560±1500 ng/g lw) and Sum(6)OH-PCBs (1997/1998: 228 ± 60 ng/g wet weight [ww], 2008: 80 ± 38 ng/g ww) in mothers were significantly lower in 2008 compared to in 1997/1998. In cubs, the plasma concentrations of Sum(21)PCBs (1997/1998: 14680 ± 5350 ng/g lw, 2008: 6070 ± 2590 ng/g lw) and Sum(6)OH-PCBs (1997/1998: 98 ± 23 ng/g ww, 2008: 49 ± 21 ng/g ww) were also significantly lower in 2008 than in 1997/1998. Sum(21)PCBs in cubs was 2.7 ± 0.7 times higher than in their mothers. This is due to a significant maternal transfer of these contaminants. In contrast, Sum(6)OH-PCBs in cubs were approximately 0.53 ± 0.16 times the concentration in their mothers. This indicates a lower maternal transfer of OH-PCBs compared to PCBs. The majority of the metabolite/precursor-ratios were lower in cubs compared to mothers. This may indicate that cubs have a lower endogenous capacity to biotransform PCBs to OH-PCBs than polar bear mothers. Exposure to PCBs and OH-PCBs is a potential health risk for polar bears, and the levels of PCBs and OH-PCBs in cubs from 2008 were still above levels associated with health effects in humans and wildlife.

Residual Stresses and Fatigue Behavior of Welded Structural Members, HR-94, 1967

A research project entitled "Residual Stresses and Fatigue Behavior of Welded Structural Members" was conducted at the Structural Research Laboratory of the Engineering Research Institute at Iowa State University under the sponsorship of the Iowa State Highway Commission. The objective of the project was to study experimentally the fatigue behavior of flange plates in welded beam sections as influenced by different residual stress distributions which are caused by different sizes of welds.

Putkien päittäishitsaaminen orbitaali-TIG-hitsauksella

Tämän kandidaatintyön tavoitteena oli esitellä orbitaali-TIG-hitsauksen käyttämistä putkien päittäishitsaamiseen. Työssä esitellään Suomesta saatavia orbitaali-TIG-laitteita ja TIG-hitsausprosessi pääperiaatteiltaan sekä prosessin käyttämistä orbitaalihitsaukseen. Myös orbitaali-TIG-hitsauksen tuottavuuteen ja laatuun liittyviä asioita käydään läpi. Suomesta saatavilla olevista laitteista valittiin toiminnallisten mittojen kannalta sopivimmat kandidaatintyötä varten suunniteltuun ripaputkilämmönvaihtimen hitsaukseen. Työ on pääasiallisesti tehty kirjallisuustutkimuksena käyttäen apuna orbitaalilaitteistojen valmistajien ja jälleenmyyjien haastatteluja. Kirjalliset lähteet koostuvat kotimaisesta ja kansainvälisestä hitsauksen alan kirjallisuudesta ja teksti on pyritty sitomaan yhteen käyttäen useaa eri lähdettä. Laitekohtaiset tiedot saatiin laitevalmistajien tuotetiedotteista ja sähköpostihaastatteluna laitteiden jälleenmyyjiltä ja laitevalmistajilta. Suomessa orbitaali-TIG-laitteita maahantuo ja jälleenmyy Masino Welding Oy ja Suomen Teknohaus Oy. Suomessa laitteita valmistaa Kemppi Oy, jonka orbitaalilaitteilla on useita jälleenmyyjiä. Masino Welding Oy myy saksalaisia Orbitalum GmbH:n laitteita ja Suomen Teknohaus Oy ranskalaisia Polysoude S.A.S.:n laitteita. Näiden laitevalmistajien joukosta suunnitellun ripaputkilämmönvaihtimen hitsaukseen soveltuu Orbitalumilta ja Polysoudelta yhdet sekä Kempiltä kaksi umpipihtimallista orbitaalihitsauspäätä. Orbitaali-TIG-hitsauslaitteissa virtalähteet ovat kehittyneet eniten vuosien aikana ja eri laitevalmistajien laitteistojen erot ovat pääasiassa virtalähteisiin liittyviä. Ripaputkilämmönvaihtimen hitsaamiseen sopivin hitsauspäämalli on umpipihti, sillä lämmönvaihtimen päädyt ovat hyvin ahtaita ja umpipihdit ovat orbitaalihitsauspäistä kaikkein kompakteimmat. Suomessa orbitaali-TIG-laitteita ei ole kauheasti tarjolla ja laitteiden markkinointi on jossain määrin kannattamatonta. Orbitaalihitsaus on kuitenkin varteenotettava vaihtoehto TIG-käsinhitsaukselle, jos hitsataan paljon samankaltaisia hitsejä.

Possibilities of advanced MAG-welding processes in shipbuilding

In shipbuilding industry welding of primer coated and tack welded steel products cause different issues. Primer coated steel products are commonly used at shipyards to ensure corrosion free storage of products in outdoor conditions. However usage of primer can cause imperfections to welds. To prevent porosity primed steel products are usually welded with tubular welding wires. Tack welds cause commonly interferences in mechanized welding when over welded, which increases costs related to welding due to increased need of preparing and repairing. The aim of this study is to research possibilities of advanced solid wire MAG-welding processes to deal with these two previously mentioned problems. This study concentrates to examine possibilities of MAG-welding, pulse MAG-welding, double pulse MAG-welding, RapidArc and ForceArc processes. Large amount of experiments were made to find out the produced porosity and the ability to over weld tack welds with each process in different circumstances. In welding of primed steel products porosity is caused mainly by hydrogen, CO, CO2, nitrous gases and zinc fumes. It was found in experiments that porosity of MAG-welding can be greatly decreased by using pulse MAG-welding instead. Also reduction of welding speed, usage of air gap and usage of solid wire product with higher amount of alloying elements reduces porosity. Researched advanced MAG-welding processes did not have an improvement into over welding of tack welds. With studied throat thicknesses and welding positions conventional MAG-welding managed better over welding of tack welds than the four studied advanced MAG-welding processes. Studied solid wire MAG-welding processes would be best suited at shipyard for mechanized welding in welding position PB. In welding positions PD and PG tubular welding wires are clearly more productive.

Hitsin juurenpuolen kriittisyys suurlujuus teräksillä

Kandidaatintyön tarkoituksena oli selvittää pienahitsin juuren kriittisyyttä. Työ oli saanut aiheen rakenneputki kokeiden yhteydessä tehdyistä havainnoista. Työssä tutustuttiin millaiset ovat pienahitsin mitoitus menetelmät ja tausta tutkimusta kuinka sitä sovelletaan käytäntöön suurlujuusteräksille. Työssä esitellään käytetyt tutkimusmenetelmät kuinka menetelmätriangulaatio saavutettiin. Tutkimuskysymyksenä oli hitsien kestävyyden mitoituksen riittävyys. Tutkimukset suoritettiin tarkastellen staattisesti kuormitettuja pienahitsejä. Pienahitsi kappaleista tehtiin laboratoriokoekappale ja FEM-laskentamalli joista vertailtiin tuloksia. Laboratoriokokeessa mittaus menetelmänä käytettiin DIC-mittausta, jolle voitiin tehdä jälkikäsittelyjä ja sieltä määrittää haluttuja datapisteitä. Laskennassa suurimmat jännityskeskittymät syntyivät hitsin kohdalle mutta vetokokeessa koekappaleeseen syntyi vauriot sularajalle ja vetokorvakkeen kiinnityshitsin rajaviivalle. Tällä kohtaa todettiin materiaalimalli riittämättömäksi, koska siihen ei ollut määritelty muutosvyöhykkeen parametreja.

Hitsauksen reaaliaikaisen NDT-tarkastuksen nykytilanne

Tämän kandidaatintyön tarkoituksena on selvittää hitsien tarkastukseen käytettyjen NDT-menetelmien nykytilannetta. Työssä kerrotaan mitä reaaliaikainen NDT-tarkastus on ja mitä menetelmiä siihen voidaan käyttää. Työn tarkoituksena on antaa lukijalle kokonaiskuva NDT-tarkastuksen nykytilasta ja siinä käytettävistä menetelmistä. Tutkimus suoritettiin kirjallisuuskatsauksena. Kirjallisuuskatsaus on luonteeltaan toteava. Lähteiden etsintä suoritettiin suurimmalta osin Internet-hakuna. NDT-tarkastusmenetelmät voidaan jakaa kahteen pääkategoriaan; pinta- ja volumetrisiin menetelmiin. Kaikki tarkastusmenetelmät eivät sovellu reaaliaikaiseen tarkastukseen. Hitsien tarkastuksessa käytetyimmät reaaliaikaiset menetelmät ovat: ultraäänitarkastus, radiografinen tarkastus, optinen spektroskopia, termografia ja pyörrevirtatarkastus. Kaikilla reaaliaikaisilla menetelmillä on omat vahvuutensa ja heikkoutensa. Työssä esitetään myös CASE-esimerkkejä reaaliaikaisesta hitsien tarkastamisesta.Tärkeimpinä johtopäätöksinä voidaan nähdä se, että hitsien NDT-tarkastuksen onnistuminen on aina hyvin tapauskohtaista ja riippuu useista muuttujista. Tästä syystä tällä hetkellä NDT-tarkastusmenetelmistä ei voi valita parasta kaikkiin käyttökohteisiin sopivaa menetelmää. Monessa prosessissa NDT-tarkastustehokkuutta ei määritä mekaanisen laitteiston mittaustarkkuus, vaan tulosten analysointiin käytettyjen algoritmien tehottomuus. Tutkimuksessa esitetään myös idea hybridi-NDT-tarkastusjärjestelmästä, jolla saataisiin havaittua tehokkaasti sekä pinta-että volumetrisia virheitä.