Aeroelastic characteristics of slender wing/bodies with freeplay non-linearities

This article presents a time domain approach to the flutter analysis of a missile-type wing/body configuration with concentrated structural non-linearities. The missile wing is considered fully movable and its rotation angle contains the structural freeplay-type non-linearity. Although a general formulation for flexible configurations is developed, only two rigid degrees of freedom are taken into account for the results: pitching of the whole wing/body configuration and wing rotation angle around its hinge. An unsteady aerodynamic model based on the slender-body approach is used to calculate aerodynamic generalized forces. Limit-cycle oscillations and chaotic motion below the flutter speed are observed in this study.

Simplified computational method for non-linear seismic analysis of bridges

After the experience gained during the past years it seems clear that nonlinear analysis of bridges are very important to compute ductility demands and to localize potential hinges. This is specially true for irregular bridges in which it is not clear weather or not it is possible to use a linear computation followed by a correction using a behaviour factor. To simplify the numerical effort several approximate methods have been proposed. Among them, the so-called Dynamic Plastic Hinge Method in which an evolutionary shape function is used to reduce the structure to a single degree of freedom system seems to mantein a good balance between accuracy and simplicity. This paper presents results obtained in a parametric study conducted under the auspicies of PREC-8 european research program.

Mode II fracture energy in the adhesive bonding of dissimilar substrates: carbon fibre composite to aluminium joints

The end-notched flexure (ENF) test calculates the value of mode II fracture energy in adhesive bonding between the substrates of same nature. Traditional methods of calculating fracture energy in the ENF test are not suitable in cases where the thickness of the adhesive is non-negligible compared with adherent thicknesses. To address this issue, a specific methodology for calculating mode II fracture energy has been proposed in this paper. To illustrate the applicability of the proposed method, the fracture energy was calculated by the ENF test for adhesive bonds between aluminium and a composite material, which considered two different types of adhesive (epoxy and polyurethane) and various surface treatments. The proposed calculation model provides higher values of fracture energy than those obtained from the simplified models that consider the adhesive thickness to be zero, supporting the conclusion that the calculation of mode II fracture energy for adhesives with non-negligible thickness relative to their adherents should be based on mathematical models, such as the method proposed in this paper, that incorporate the influence of this thickness.

Seismic performance case study of bridge pile cap foundation

The purpose of this report is to build a model that represents, as best as possible, the seismic behavior of a pile cap bridge foundation by a nonlinear static (analysis) procedure. It will consist of a reproduction of a specimen already built in the laboratory. This model will carry out a pseudo static lateral and horizontal pushover test that will be applied onto the pile cap until the failure of the structure, the formation of a plastic hinge in the piles due to the horizontal deformation, occurs. The pushover test consists of increasing the horizontal load over the pile cap until the horizontal displacement wanted at the height of the pile cap is reached. The output of this model will be a Skeleton curve that will plot the lateral load (kN) over the displacement (m), so that the maximum movement the pile cap foundation can reach before its failure can be calculated. This failure will be achieved when the load at that specific shift is equal to 85% of the maximum. The pile cap foundation finite element model was based on pile cap built for a laboratory experiment already carried out by the Master student Deming Zhang at Tongji University. Two different pile caps were tested with a difference in height above the ground level. While one has 0:3m, the other rises 0:8m above the ground level. The computer model was calibrated using the experimental results. The pile cap foundation will be programmed in a finite element environment called OpenSees (Open System for Earthquake Engineering Simulation [28]). This environment is a free software developed by Berkeley University specialized, as it name says, in the study of earthquakes and its effects on structures. This specialization is the main reason why it is being used for building this model as it makes it possible to build any finite element model, and perform several analysis in order to get the results wanted. The development of OpenSees is sponsored by the Pacific Earthquake Engineering Research Center through the National Science Foundation engineering and education centers program. OpenSees uses Tcl language to program it, which is a language similar to C++.

Moment transfer and influence of transverse beams in interior waffle flat plate-column connections under lateral loading

This paper addresses two aspects of the behavior of interior reinforced concrete waffle flat plate?column connections under lateral loads: the share of the unbalanced moment between flexure and excentric shear, and the effect of the transverse beams. A non-linear finite element model (benchmark model) was developed and calibrated with the results of quasi-static cyclic tests conducted on a 3/5 scale specimen. First, from this numerical model, the portion cv of the unbalanced moment transferred by the excentricity of shear about the centroid of the critical sections defined by Eurocode 2 (EC-2) and by ACI 318-11 was calculated and compared with the share-out prescribed by these codes. It is found that while the critical section of EC-2 is consistent with the cv provided by this code, in the case of ACI 318-11, the value assigned to cv is far below (about 50% smaller) the actual one obtained with the numerical simulations. Second, from the benchmark model, seven additional models were developed by varying the depth D of the transverse beam over the thickness h of the plate. It was found that the ductility of the connection and the effective width of the plate can respectively be increased up to 50% and 10% by raising D/h to 2 and 1.5.

Mechanical behavior of tungsten-vanadium-lanthana alloys as function of temperature

The mechanical behavior of three tungsten (W) alloys with vanadium (V) and lanthana (La2O3) additions (W–4%V, W–1%La2O3, W–4%V–1%La2O3) processed by hot isostatic pressing (HIP) have been compared with pure-W to analyze the influence of the dopants. Mechanical characterization was performed by three point bending (TPB) tests in an oxidizing air atmosphere and temperature range between 77 (immersion tests in liquid nitrogen) and 1273 K, through which the fracture toughness, flexural strength, and yield strength as function of temperature were obtained. Results show that the V and La2O3 additions improve the mechanical properties and oxidation behavior, respectively. Furthermore, a synergistic effect of both dopants results in an extraordinary increase of the flexure strength, fracture toughness and resistance to oxidation compared to pure-W, especially at higher temperatures. In addition, a new experimental method was developed to obtain a very small notch tip radius (around 5–7 μm) and much more similar to a crack through the use of a new machined notch. The fracture toughness results were lower than those obtained with traditional machining of the notch, which can be explained with electron microscopy, observations of deformation in the rear part of the notch tip. Finally, scanning electron microscopy (SEM) examination of the microstructure and fracture surfaces was used to determine and analyze the relationship between the macroscopic mechanical properties and the micromechanisms of failure involved, depending on the temperature and the dispersion of the alloy.

Comportamiento a fatiga por cortante de elementos lineales de hormigón armado sin cercos

Las estructuras de hormigón son susceptibles de sufrir los efectos asociados a las acciones de fatiga cuando estas se ven sometidas a un elevado número de cargas repetidas. Muchas de estas estructuras no requieren armadura transversal para cumplir los condicionantes de dimensionamiento estático como por ejemplo las losas superiores de tableros de puentes, los muros de contención, las losas de transición de puentes, las torres eólicas o las estructuras marítimas. La mayor parte de los códigos de diseño vigentes no incluyen una comprobación específica del nivel de seguridad a cortante de estas estructuras para acciones de fatiga, y aquellas que lo hacen prefieren utilizar expresiones de tipo empírico basadas en curvas S-N que relacionan el número de ciclos resistentes con el valor de la carga aplicada. A pesar de que el empleo de curvas S-N es de gran utilidad desde un punto de vista práctico, estas curvas no permiten comprender el proceso de rotura por cortante para cargas repetidas. El objetivo principal de esta Tesis es el de estudiar el comportamiento a cortante de elementos de hormigón armado sin cercos sometidos a fatiga. Además, el análisis es ampliado al estudio del comportamiento transversal de los voladizos de las losas superiores de tableros de puentes de hormigón que de forma habitual son diseñados sin armadura de cortante. De forma habitual estos elementos se diseñan atendiendo a criterios de dimensionamiento estáticos sin tener en cuenta la resistencia a cortante cuando se ven sometidos a cargas cíclicas. A pesar de que las cargas de fatiga son inferiores a aquellas que producen el fallo estático, es importante tener en cuenta el comportamiento de estos elementos ante cargas repetidas. Los trabajos experimentales existentes en vigas de hormigón armado sin cercos evidenciaron diferencias significativas entre los modos de fallo ante cargas estáticas y cíclicas. Estos trabajos llegaron a la conclusión de que estos elementos diseñados para tener un fallo dúctil por flexión pueden llegar a desarrollar un tipo de fallo frágil por cortante cuando se ven sometidos a cargas repetidas. El proceso de rotura por cortante en elementos de hormigón armado sin cercos sometidos a fatiga es un proceso complejo que debe ser estudiado en profundidad debido al carácter frágil de este tipo de fallo. Los trabajos experimentales permitieron comprobar que el origen de este fallo tiene lugar tras la formación de una fisura de cortante a partir de una fisura de flexión formada durante los primeros ciclos en el vano de cortante. Tras la formación de esta fisura, esta se va propagando hacia la cabeza de compresión hasta que finalmente se produce el fallo como consecuencia de la destrucción de la cabeza de compresión cuando la altura alcanzada por esta es insuficiente para resistir la fuerza de compresión aplicada en esta zona. Por otra parte, la propagación de esta fisura diagonal puede desarrollarse por completo en el instante en el que esta se forma derivando en un tipo de fallo por cortante más frágil que el anterior. El proceso de fatiga es estudiado en esta Tesis mediante un modelo mecánico. Por una parte, se propone un modelo predictivo para determinar el número de ciclos acumulados hasta que se forma la fisura diagonal en función del estado tensional que se tiene en la punta de una fisura crítica de flexión formada en los primeros ciclos. Por otra parte, la resistencia a fatiga tras la formación de la fisura diagonal se analiza teniendo en cuenta el daño por fatiga acumulado en la cabeza de compresión y las variables que afectan a la propagación de esta fisura de cortante. Para la evaluación de la resistencia a fatiga tras la formación de la fisura crítica de cortante en este tipo de elementos, se plantea un modelo teórico basado en conceptos de Mecánica de la Fractura adaptados al hormigón. Este modelo puede ser aplicado a vigas de hormigón armado sin cercos de canto constante o variable siguiendo diferentes procedimientos. Una campaña experimental ha sido llevada a cabo con el objetivo de estudiar el comportamiento a cortante de vigas de hormigón armado sin cercos de canto variable sometidas a cargas estáticas y de fatiga. Se han desarrollado un total de diez ensayos estáticos y de fatiga para diferentes niveles de carga y esbelteces de cortante, teniendo lugar diferentes modos de fallo. Estos elementos fueron diseñados para reproducir, a escala real y de forma simplificada, los voladizos laterales de las losas superiores de tableros de puentes de carretera de hormigón. Los resultados experimentales demostraron que el tipo de fallo desarrollado depende de varios parámetros como por ejemplo el nivel de carga máxima, el nivel de oscilación de tensiones en la armadura longitudinal, la esbeltez de cortante o la calidad del hormigón utilizado entre otros. Para valores similares de esbeltez de cortante, los ensayos de fatiga realizados permitieron comprobar que la rotura por cortante de estos elementos está asociada a niveles de carga máxima elevados, mientras que el fallo por fatiga de la armadura longitudinal tiene mayor probabilidad de ocurrir en elementos sometidos a elevados niveles de oscilación de tensiones en esta armadura. Además, estos ensayos han sido analizados a través del modelo propuesto para tratar de comprender el comportamiento resistente de estos elementos sometidos a cargas de fatiga. Concrete structures are able to suffer fatigue when they are subjected to high number of cyclic loads. Many of these need not shear reinforcement to satisfy static design requirements, such as bridge deck slabs, retaining walls, bridge approach slabs, wind towers or maritime structures among others. Many codes of practice do not include a verification of the shear fatigue safety. Moreover, those which include it still prefer empirical S-N-based approaches that provide the number of cycles as a function of applied forces. S-N models are practical but they do not provide information to understand the shear fatigue process. The main objective of this Thesis is to study shear behaviour of reinforced concrete elements without stirrups subjected to fatigue loads. In addition, the analysis is extended in order to study the transverse behaviour of cantilever slabs of concrete bridges that traditionally are designed without shear reinforcement. These elements usually are designed on the basis of static strength and it is unusual that codes consider fatigue strength of concrete in shear. Accordingly, it is important to take into account the fatigue behaviour of structural members subjected to cyclic loads although these loads are lower than those which produce the static failure. Existing experimental works show important differences between the static and cyclic failure modes of reinforced concrete beams without stirrups. These works concluded that beams without transverse reinforcement, designed to have a ductile failure mode in flexure, can submit a brittle shear failure mode when they are subjected to repeated loads. Shear fatigue failure of reinforced concrete beams without stirrups is a rather complex process from the mechanical viewpoint. Since it leads to a brittle failure mode it should be better understood. Experimental evidence indicates that a diagonal crack first develops from the inclination of flexural cracks in the shear span. Thereafter, the diagonal crack propagates into the compression zone. Failure normally takes place by the destruction of the compression zone when its depth is too small to resist the applied force. The propagation of the diagonal crack can also be instantaneous, leading to sudden diagonal cracking fatigue failure rather than shear-compression failure. Fatigue process is studied in this Thesis on a mechanical basis. On the one hand, a predictive model is derived to obtain the number of cycles up to diagonal cracking, as a function of the stress state at the tip of a critical flexural crack. On the other hand, the residual fatigue strength after diagonal cracking is analyzed taking into account the fatigue damage accumulated by the compression zone and the variables affecting the propagation of the diagonal crack. In order to assess the residual fatigue strength after diagonal cracking of such elements, a theoretical model is proposed based on concepts from fracture mechanics adapted to concrete. This model can be successfully applied for straight or haunched reinforced concrete beams without stirrups following different procedures. In order to achieve a more advanced knowledge in this subject, an experimental campaign has been carried out with the aim of study the shear behaviour of reinforced concrete haunched beams without stirrups subjected to static and fatigue loads. A total of ten static and fatigue tests have been performed with distinct load levels and shear span-to-depth ratios, presenting different failures modes. These elements were designed to reproduce in a simplified form the cantilever slab of concrete bridges at real scale. Experimental results showed that the type of failure depends on several parameters as for example the maximum load level, the stress oscillation level on the longitudinal reinforcement, the shear span-to-depth ratio or the quality of the concrete used among others. For a similar value of the shear span-to-depth ratio, tests evidenced that shear fatigue failure is related to high maximum load levels, while steel fatigue failure is easier to occur in elements subjected to high stress oscillation level on the reinforcement bars. Besides, these tests have been analyzed through the proposed model in order to clarify the structural behaviour of such elements subjected to fatigue loads.

Spatial divisions of society

The encounter of architecture and urbanism with parcelisation is marked with the sign of a historical debt. Parcelisation is a tremendously powerful design tool. Architecture and urban planning attest to its capacity to shape sociospatial relations across a range of scales and contexts. From Renaissance palazzi to modernist slabs, from nation-wide agrarian reforms and Haussmann’s Paris to Christopher Alexander’s new theory of urban design and Michael Webb’s Suitaloon — most of the historical revolutions and experimental projects that have shaken these fields have relied, consciously or not, on a critique and restructuration of inherited divisions of land and space. The layout of parcel patterns has a series of implications including forms of property, the divide between private and public realms, the distribution of spatial contents and uses through zoning, typological decisions and so forth. The behaviour of any urban structure depends on the tissue of plots that configures the urban fabric and many of the challenges urban design faces today —complexity, urban vitality, social equality, etc.— hinge upon the forms of land division and distribution we adopt.

A discrete spectral model for intermediate crack debonding in FRP-strengthened RC beams

One of the common failure modes of reinforced concrete (RC) beams strengthened in flexure with a bonded fibre-reinforced polymer (FRP) is intermediate crack (IC) debonding, which is originated at a critical section in the vicinity of flexural cracks and propagates to a plate end. Despite considerable research over the last years, few reliable and simplified IC debonding strength models have been developed. This paper firstly presents a one-dimensional model based on the discrete crack approach for concrete and the spectral element method for the numerical simulation of the IC debonding process. The progressive formation of flexural cracks and subsequent concrete-FRP interfacial debonding is formulated by the introduction of a new element able to represent both phenomena simultaneously without perturbing the numerical procedure. Furthermore, with the proposed model, high frequency dynamic response for these kinds of structures can also be obtained in a very simple and non-expensive way, which makes this procedure very useful as a tool for diagnoses and detection of debonding in its initial stage by monitoring the change in local dynamic characteristics.

Diseño metodológico para la creación y desarrollo de organizaciones innovadoras, basadas en un modelo de liderazgo que genere entornos facilitadores de la creatividad, implantación de procesos de innovación y creación de productos y servicios innovadores

La presente investigación tiene como objetivo el desarrollo de una metodología que favorezca la innovación en las empresas a través de la actividad directiva, analizando a su vez, su influencia a nivel macro, en los sistemas de innovación, en las políticas de innovación y en el capital intelectual y a nivel micro, en la innovación, en el desempeño y en el clima organizacional. Se estima importante realizar un estudio sobre este tema debido a que la innovación se considera un pilar crítico para el desarrollo social a través de la competitividad de las empresas, así como, una fuente importante de ventaja competitiva. Existe abundante literatura sobre la influencia de la innovación en la gestión empresarial y el papel que el liderazgo desempeña en términos generales. Sin embargo, la literatura presenta diversos estilos de liderazgo sin mostrar una línea consistente de interrelación entre ellos, por lo que finalmente no existe una relación sólida entre el liderazgo, la gestión empresarial y la innovación. Este hecho se debe, como se muestra en la tesis, a que la literatura analiza las organizaciones y el liderazgo desde una perspectiva sociológica u organizacional, y otra desde la perspectiva psicológica sin aportar una línea de articulación entre ambas. Es decir, la literatura analiza el comportamiento organizacional pero no su causa. A lo largo de la tesis se van desarrollando diferentes líneas de trabajo que se convierten en aportaciones empíricas y académicas. Así, una de las aportaciones de la tesis es la sustitución de la figura del líder como persona, por la de un directivo con una doble función; por un lado, la función de liderazgo cuyo objetivo es generar cambio y por el otro, la función de gestionar el día a día o desempeño. Sustituir la figura del líder por una doble funcionalidad directiva facilita la comprensión del concepto liderazgo, lo que permite a su vez, establecer estrategias para su desarrollo, haciendo una realidad el que el liderazgo puede ser aprendido. Este resultado constituye la primera aportación de la tesis. Así mismo, a través de un exhaustivo análisis de la literatura, se desarrolla una propuesta de liderazgo integrado de acuerdo con el modelo Stuart-Kotze, el cual se describe también ampliamente. Encontrar un modelo único de liderazgo supone la piedra angular para el desarrollo de la metodología. Esta propuesta de liderazgo integrado da lugar a la segunda aportación de la tesis. Del mismo modo, se realiza un estudio en profundidad de la perspectiva psicológica de las organizaciones desarrollando el constructo Miedo al Error (ME) que resulta ser un rasgo de la personalidad existente en todos los seres humanos y que presenta una influencia negativa tanto en el desempeño, como en la innovación empresarial. Este resultado permite identificar cuales son las verdaderas barreras para el ejercicio del liderazgo, señalando que la disminución del ME debe ser considerada como una competencia de la Inteligencia Emocional a ser desarrollada por los directivos. Este resultado constituye la tercera aportación de la tesis. Una vez desarrollado el modelo de gestión empresarial expuesto, se procede a su validación, analizando la relación entre los constructos que definen el modelo de gestión: el desempeño, la innovación y el ME. Para identificar las influencias o relaciones de causalidad que subyacen entre los constructos, se utilizó la técnica del modelo de ecuaciones estructurales (SEM). La población objeto de estudio estuvo constituida por 350 profesionales con responsabilidad directiva, procedentes de empresas del sector servicios repartidas por toda la geografía española. Como fuente primaria de recolección de información se utilizó el cuestionario desarrollado por Stuart-Kotze M-CPI (Momentum Continuous Performance Improvement). En primer lugar se procedió a evaluar las propiedades psicométricas del modelo de medida, llevándose a cabo un análisis factorial exploratorio (AFE) y un análisis factorial confirmatorio (AFC) de segundo orden. Los resultados obtenidos ponen de manifiesto que el constructo desempeño (D) viene determinado por dos dimensiones, (DOP), desempeño orientado hacia la planificación y (DORT), desempeño orientado hacia la realización de la tarea. Es decir, la muestra de directivos no percibe que la planificación en el día a día y la realización de la tarea estén articuladas. Posteriormente se procede a realizar el contraste del modelo a través del método de ecuaciones estructurales. Los resultados muestran que la relación de influencia de la dimensión DOP no es significativa, por lo que el constructo D queda representado únicamente por la dimensión DORT. Los resultados de la investigación proporcionan conclusiones e hipótesis para futuras investigaciones. Si bien la muestra de directivos realiza un plan estratégico, éste no se tiene en cuenta en el día a día. Este hecho podría explicar el alto grado de administración por crisis tan frecuente en la empresa española. A su vez, el ME presenta una influencia negativa en la innovación, lo que concuerda con la literatura. Al respecto, considerar el ME como un rasgo de la personalidad, presente tanto en directivos como en colaboradores, facilita la comprensión de las barreras de la organización hacia la comunicación abierta a la vez, que una dirección de trabajo para la mejora de la capacidad innovadora de la organización. Por último, los resultados establecen la existencia de una relación causal entre el desempeño diario y la innovación. Con respecto a este segundo resultado y analizando los comportamientos que identifican el constructo D surgen también varias conclusiones e hipótesis para futuras investigaciones. Los resultados ponen de manifiesto que la muestra de directivos genera iniciativas de cambio con la finalidad de que el trabajo diario salga adelante según los estándares de calidad definidos. Sin embargo, estas iniciativas sólo proceden de los directivos, sin participación alguna de los colaboradores, los cuales son sólo responsables de la implementación produciéndose la consiguiente desmotivación y pérdida de oportunidades. Esta conclusión pone de manifiesto que la innovación de las empresas de la muestra sucede para garantizar la eficiencia de los procesos existentes, pero en ningún caso surge de la iniciativa de buscar una mejor eficacia empresarial. Este hecho plantea un origen doble de la innovación en los procesos. La innovación proactiva que buscaría la mejora de la eficacia de la organización y una innovación de carácter reactiva que buscaría la salvaguarda de la eficiencia. Quizás sea esta la causa del gap existente entre la innovación en España y la innovación de los países que ocupan los primeros puestos en el ranking de producción de innovación lo que constituye un importante punto de partida para una investigación futura. ABSTRACT This research aims to develop a methodology that supports innovation in companies through the managers’ activity, analysing in turn its influence at the macro level: innovation systems, innovation policies and Intellectual capital and at the micro level: innovation itself, performance and organizational climate. It is considered important to conduct a study on this subject due to the fact that innovation is considered a critical pillar for the development and future of the enterprise and an important source of competitive advantage. There is abundant literature about the influence of innovation in business management and the role that leadership plays in general terms. However, the literature presents various styles of leadership without showing a consistent relationship among them, so finally there is not a strong relationship among leadership, business management and innovation. As shown in the thesis, this is due to the fact that the literature analyses organizations and leadership from a sociological or organizational perspective and from a psychological perspective, without providing a hinge line between the two. That is, the existing literature discusses organizational behaviour but not its cause. Throughout the thesis, different lines of work that become empirical and academic contributions have been developed. Thus, one of the contributions of the thesis is replacing the figure of the leader as a person, by a manager with a dual function. Firstly, we have the leadership role which aims to generate change and, on the other hand, the function to manage the day-to-day task or performance. Replacing the figure of the leader by a dual managerial functionality facilitates the understanding of the leadership concept, allowing in turn, to establish development strategies and making true that leadership can be learned. This outcome is the first contribution of the thesis. Likewise, through a comprehensive literature review, an integrated leadership proposal is developed, according to the Kotze model, which is also described widely. Finding a specific leadership model represents the cornerstone for the development of the methodology. This integrated leadership proposal leads to the second contribution of the thesis. Similarly, an in-depth study was conducted about the psychological perspective of the organizations disclosing the construct Fear of Failure. This construct is a personality trait that exists in all human beings and has a negative influence on both performance and business innovation. This outcome allows identifying which are the real barriers to the exercise of leadership, noting that the decrease in fear of failure must be considered as an Emotional Intelligence competence to be developed by managers. This outcome represents the third contribution of the thesis. Once a business management model has been developed, we proceed to its validation by analysing the relationship among the model constructs: management, innovation and fear of failure. To identify the influence or causal relationships underlying the constructs, a structural equation model (SEM) technique was used. The study population consisted of 350 professionals with managerial responsibility, from companies in the services sector scattered throughout the Spanish geography. As a primary source for gathering information a questionnaire developed by Kotze M-CPI (Continuous Performance Improvement Momentum) was used. First we proceeded to evaluate the psychometric properties of the measurement model, carrying out an exploratory factorial analysis (EFA) and a confirmatory factorial analysis (CFA) of second order. The results show that the performance construct D is determined by two-dimensions (DOP: performance oriented to planning) and (DORT: aiming at the realization of the task). That is, the sample of managers does not perceive that planning and the daily task are articulated. Then, we proceeded to make the contrast of the model through a structural equation model SEM. The results show that the influence of the DOP dimension is not significant, so that only the DORT dimension finally represents the construct D. The research outcomes provide conclusions and hypotheses for future research. Although the managers in the sample develop a strategic plan, it seems that managers do not take it into account in their daily tasks. This could explain the high degree of crisis management so prevalent in the Spanish companies. In turn, the fear of failure has a negative influence on innovation, consistent with the literature. In this regard, the fear of failure is considered as a personality trait, present in both managers and employees, which enables the understanding of organizational barriers to open communication and provides a direction to improve the organization’s innovative capacity as well. Finally, the results establish a causal relationship between daily performance and innovation. Regarding this second outcome and analysing the behaviours that identify the construct D, several conclusions and hypotheses for future research arise as well. The results show that the managers in the sample show initiatives of change in order to make everyday work go ahead, according to defined quality standards. However, these initiatives only come from managers without any participation of coworkers, which are only responsible for the implementation, and this produces discouragement and loss of opportunities. This finding shows that the innovation by the companies in the sample happens to guarantee the efficiency of existing processes, but do not arise from an initiative that seeks better business efficacy. This raises two sources of innovation in processes. The first source would be a proactive innovation that would seek improved organizational efficacy. The second one is a reactive innovation that would seek to safeguard efficiency. Perhaps this is the cause of the existing gap between the innovation activity in Spain and the innovation activity in those countries that occupy the top positions in the ranking of innovation outcomes. The Spanish companies seek process efficiency and the top innovators business efficacy. This is an important starting point for future research.

Estudio teórico-experimental para la mejora de la resistencia estructural de autocares basado en el diseño de uniones y asientos

La presente tesis analiza la mejora de la resistencia estructural ante vuelco de autocares enfocando dos vías de actuación: análisis y propuestas de requisitos reglamentarios a nivel europeo y la generación de herramientas que ayuden al diseño y a la verificación de estos requisitos. Los requisitos reglamentarios de resistencia estructural a vuelco contemplan la superestructura de los vehículos pero no para los asientos y sistemas de retención. La influencia de los pasajeros retenidos es superior a la incluida en reglamentación (Reg. 66.01) debiendo considerarse unida al vehículo un porcentaje de la masa de los pasajeros del 91% para cinturón de tres puntos y del 52% para cinturón subabdominal frente al 50% reglamentario para todos los casos. Se ha determinado la cinemática y dinámica del vuelco normativo en sus diferentes fases, formulando las energías en las fases iniciales (hasta el impacto contra el suelo) y determinando la fase final de deformación a través del análisis secuencial de ensayos de módulos reales. Se han determinado los esfuerzos para los asientos que se dividen en dos fases diferenciadas temporalmente: una primera debida a la deformación estructural y una segunda debida al esfuerzo del pasajero retenido que se produce en sentido opuesto (con una deceleración del pasajero en torno a 3.3 g). Se ha caracterizado a través de ensayos cuasi.estáticos el comportamiento de perfiles a flexión y de las uniones estructurales de las principales zonas del vehículo (piso, ventana y techo) verificándose la validez del comportamiento plástico teórico Kecman.García para perfiles de hasta 4 mm de espesor y caracterizando la resistencia y rigidez en la zona elástica de las uniones en función del tipo de refuerzo, materiales y perfiles (análisis de más de 180 probetas). Se ha definido un método de ensayo cuasi.estático para asientos ante esfuerzos de vuelco, ensayándose 19 butacas y determinándose que son resistentes (salvo las uniones a vehículo con pinzas), que son capaces de absorber hasta más de un 17% de la energía absorbida, aunque algunos necesitan optimización para llegar a contribuir en el mecanismo de deformación estructural. Se han generado modelos simplificados para introducir en los modelos barra.rótula plástica: un modelo combinado unión+rótula plástica (que incluye la zona de rigidez determinada en función del tipo de unión) para la superestructura y un modelo simplificado de muelles no.lineales para los asientos. Igualmente se ha generado la metodología de diseño a través de ensayos virtuales con modelos de detalle de elementos finitos tanto de las uniones como de los asientos. Se ha propuesto una metodología de diseño basada en obtener el “mecanismo óptimo de deformación estructural” (elevando la zona de deformación lateral a nivel de ventana y en pilar o en costilla en techo). Para ello se abren dos vías: diseño de la superestructura (selección de perfiles y generación de uniones resistentes) o combinación con asientos (que en lugar de solo resistir las cargas pueden llegar a modificar el mecanismo de deformación). Se ha propuesto una metodología de verificación alternativa al vuelco de vehículo completo que contempla el cálculo cuasi.estático con modelos simplificados barra.rótula plástica más el ensayo de una sección representativa con asientos y utillajes antropomórficos retenidos que permite validar el diseño de las uniones, determinar el porcentaje de energía que debe absorberse por deformación estructural (factor C) y verificar el propio asiento como sistema de retención. ABSTRACT This research analyzes the improvement of the structural strength of buses and coaches under rollover from two perspectives: regulatory requirements at European level and generation of tools that will help to the design and to the verification of requirements. European Regulations about rollover structural strength includes requirements for the superstructure of the vehicles but not about seats, anchorages and restraint systems. The influence of the retained passengers is higher than the one included currently in the Regulations (Reg. 66.01), being needed to consider a 91% of the passenger mass as rigidly joint to the vehicle (for 3 points’ belt, a 52% for 2 points’ belt) instead of the 50% included in the Regulation. Kinematic and dynamic of the normative rollover has been determined from testing of different sections, formulating the energies of the first phases (up to the first impact with the ground) and determining the last deformation phase through sequential analysis of movements and deformations. The efforts due to rollover over the seats have been established, being divided in two different temporal phases: a first one due to the structural deformation of the vehicle and a second one due to the effort of the restrained passenger being this second one in opposite sense (with a passenger deceleration around 3.3 g). From quasi.static testing, the behavior of the structural tubes under flexural loads, including the principal joints in the vehicle (floor, window and roof), the validity of the theoretical plastic behavior according Kecman.García theories have been verified up to 4 mm of thickness. Strength of the joints as well as the stiffness of the elastic zone has been determined in function of main parameters: type of reinforcement, materials and section of the tubes (more than 180 test specimens). It has been defined a quasi.static testing methodology to characterize the seats and restrain system behavior under rollover, testing 19 double seats and concluding that they are resistant (excepting clamping joints), that they can absorb more than a 17 of the absorbed energy, and that some of them need optimization to contribute in the structural deformation mechanism. It has been generated simplified MEF models, to analyze in a beam.plastic hinge model: a combined model joint+plastic hinge (including the stiffness depending on the type of joint) for the superstructure and a simplified model with non.lineal springs to represent the seats. It has been detailed methodologies for detailed design of joints and seats from virtual testing (MEF models). A design methodology based in the “optimized structural deformation mechanism” (increasing the height of deformation of the lateral up to window level) is proposed. Two possibilities are analyzed: design of the superstructure based on the selection of profiles and design of strength joints (were seats only resist the efforts and contribute in the energy absorption) or combination structure.seats, were seats contributes in the deformation mechanism. An alternative methodology to the rollover of a vehicle that includes the quasi.static calculation with simplified models “beam.joint+plastic hinge” plus the testing of a representative section of the vehicle including seats and anthropomorphic ballast restrained by the safety belts is presented. The test of the section allows validate the design of the joints, determine the percentage of energy to be absorbed by structural deformation (factor C) and verify the seat as a retention system.

Gust wind tunnel study on ballast pick-up by high-speed trains

This paper describes the experimental setup, procedure, and results obtained, concerning the dynamics of a body lying on a floor, attached to a hinge, and exposed to an unsteady flow, which is a model of the initiation of rotational motion of ballast stones due to the wind generated by the passing of a high-speed train. The idea is to obtain experimental data to support the theoretical model developed in Sanz-Andres and Navarro-Medina (J Wind Eng Ind Aerodyn 98, 772–783, (2010), aimed at analyzing the initial phase of the ballast train-induced-wind erosion (BATIWE) phenomenon. The experimental setup is based on an open circuit, closed test section, low-speed wind tunnel, with a new sinusoidal gust generator mechanism concept, designed and built at the IDR/UPM. The tunnel’s main characteristic is the ability to generate a flow with a uniform velocity profile and sinusoidal time fluctuation of the speed. Experimental results and theoretical model predictions are in good agreement.

Relationship between residual stresses and mechanical behavior in ceramic composites

En este trabajo, materiales de tipo alúmina/Y-TZP (ZrO2 tetragonal, estabilizada con 3 mol. % Y2O3), como sistema cerámico popular por sus mejoradas propiedades mecánicas en comparación con las cerámicas de alúmina puras, han sido estudiados en términos de propiedades mecánicas y tensiones residuales. El novedoso método de colado en cinta, consistente en el apilamiento de cintas de cerámica verde a temperatura ambiente y el uso de bajas presiones, se ha escogido para la presente investigación con el fin de poder aprovechar al máximo el futuro desarrollo de materiales laminados de alúmina-óxido de circonio. Se han determinado las propiedades de los materiales obtenidos por este nuevo método de procesamiento comparándolas con las de los materiales obtenidos por “slip casting”, con el fin de analizar si el método propuesto afecta a la microestructura y, por tanto, a las propiedades mecánicas y tensiones residuales propias de estos materiales. Para analizar la idoneidad del proceso de fabricación, utilizado para evitar la presencia de discontinuidades en las intercaras entre las láminas así como otros fenómenos que puedan interferir con las propiedades mecánicas, se estudiaron materiales cerámicos con la misma composición en cintas. Por otra parte también se analizó el efecto de la adición de óxido de circonio sobre la aparición de tensiónes residuales en cerámicas Al2O3/Y-TZP, teniendo en cuenta su notable influencia sobre las propiedades microestructurales y mecánicas de los materiales, así como el requisito de co-sinterización de capas con diferentes materiales compuestos en materiales laminados. La caracterización del material incluye la determinación de la densidad, el análisis de la microestructura, la obtención de las propiedades mecánicas (módulo de elasticidad, dureza, resistencia a la flexión y tenacidad de fractura) así como de las tensiones residuales. En combinación con otros métodos de medida tradicionales, la nanoindentación también se empleó como una técnica adicional para la medida del módulo de elasticidad y de la dureza. Por otro lado, diferentes técnicas de difracción con neutrones, tanto las basadas en longitud de onda constante (CW) como en tiempo de vuelo (TOF), han sido empleadas para la medición fiable de la deformación residual a través del grosor en muestras a granel. Las tensiones residuales fueron determinadas con elevada precisión, aplicando además métodos de análisis apropiados, como por ejemplo el refinamiento de Rietveld. Las diferentes fases en cerámicas sinterizadas, especialmente las de zirconia, se examinaron con detalle mediante el análisis de Rietveld, teniendo en cuenta el complicado polimorfismo del Óxido de Zirconio (ZrO2) así como las posibles transformaciones de fase durante el proceso de fabricación. Los efectos del contenido de Y-TZP en combinación con el nuevo método de procesamiento sobre la microestructura, el rendimiento mecánico y las tensiones residuales de los materiales estudiados (Al2O3/Y-TZP) se resumen en el presente trabajo. Finalmente, los mecanismos de endurecimiento, especialmente los relacionados con las tensiones residuales, son igualmente discutidos. In present work, Alumina/Y-TZP (tetragonal ZrO2 stabilized with 3 mol% Y2O3) materials, as an popular ceramic system with improved mechanical properties compared with the pure alumina ceramics, have been studied in terms of mechanical properties and residual stresses. The novel tape casting method, which involved the stacking of green ceramics tapes at room temperature and using low pressures, is selected for manufacturing and investigation, in order to take full advantage of the future development of alumina-zirconia laminated materials. Features of materials obtained by the new processing method are determined and compared with those of materials obtained by conventional slip casting in a plaster mold, in order to study whether the proposed method of processing affects microstructure and thereby the mechanical properties and residual stresses characteristics of materials. To analyse the adequacy of the manufacturing process used to avoid the presence of discontinuities at the interfaces between the sheets and other phenomena that interfere with the mechanical properties, ceramic materials with the same composition in tapes were investigated. Moreover, the effect of addition of zirconia on residual stress development of Al2O3/Y-TZP ceramics were taken into investigations, considering its significantly influence on the microstructure and mechanical properties of materials as well as the requirement of co-sintering of layers with different composites in laminated materials. The characterization includes density, microstructure, mechanical properties (elastic modulus, hardness, flexure strength and fracture toughness) and residual stresses. Except of the traditional measurement methods, nanoindentation technique was also used as an additional measurement of the elastic modulus and hardness. Neutron diffraction, both the constant-wavelength (CW) and time-of-flight (TOF) neutron diffraction techniques, has been used for reliable through-thickness residual strain measurement in bulk samples. Residual stresses were precisely determined combined with appropriate analysis methods, e.g. the Rietveld refinement. The phase compositions in sintered ceramics especially the ones of zirconia were accurately examined by Rietveld analysis, considering the complex polymorph of ZrO2 and the possible phase transformation during manufacturing process. Effects of Y-TZP content and the new processing method on the microstructure, mechanical performance and residual stresses were finally summarized in present studied Al2O3/Y-TZP materials. The toughening mechanisms, especially the residual stresses related toughening, were theoretically discussed.

Las casualidades controladas : la primera visibilidad del cambio del paradigma moderno

Como no pocos proyectos, el origen de esta tesis es fruto de una casualidad. Hace unos años me topé en Londres, en la librería Walden Books del 38 de Harmood St., con una primera edición de la conocida monografía de Mies a cargo de Philip Johnson. El librito, en realidad catálogo de la exposición que en 1947 el MoMA de Nueva York dedicara a la obra de Mies Van der Rohe a los diez años del desembarco del arquitecto en Estados Unidos, tiene un tamaño de 10 x 7,5 pulgadas, es decir, la mitad del formato americano Crown (20x15 pulgadas), equivalente a 508 x 381 mm. Se imprimieron, en su primera tirada, editada por The Plantin Press, 12.000 ejemplares. Ese mismo año, con edición al cuidado de Reynal y Hitchcock, se publicaría la primera traducción al inglés de Cuando las catedrales eran blancas de Le Corbusier y una selección de poemas de Lorca, siete años después de su Poeta en Nueva York. En la monografía, en la página 109, aparece el conocido croquis de Mies Sketch for a glass house on a hillside. c. 1934, escasamente unas líneas, aunque precisas y llenas de matices, de la casa en una ladera que rápidamente nos remite a aquella primera propuesta de Saarinen para una casa en el aire, primero en 1941 en Pensilvania y después, en 1945, con Charles Eames, en Los Angeles, que nunca llegarían a construirse, sino en su aliteraciones posteriores realizadas por Harry Seidler (Julian Rose House, Wahroonga, Sydney, 1949), Philip Johnson (Leonhardt house, Long Island, Nueva York, 1956) o Craig Ellwood (Smith House, Crestwood Hills, 1958; Frank & Polly Pierson House, Malibú, 1962; Chamorro House, Hollywood Hills, 1963, o la serie Weekend House, con Gerald Horn, entre 1964 y 1970, hasta el magnífico Art Center College of Design de Pasadera, su puente habitado de 1977). El relato que da origen al texto discurre en un estricto período de tiempo, desde los primeros dibujos de la Case Study House nº8, dentro del programa promovido por John Entenza y su revista Arts & Architecture en California, realizados en el estudio de Saarinen en Bloomfield Hills, Michigan, hasta que el proyecto de la casa Eames finaliza cinco años después de acabar la obra en 1955, en la versión conocida, radicalmente distinta al proyecto original, cuando la pareja Charles y Ray Eames edita el corto House After Five Years of Living. La discusión original en torno a esta casita, o mejor, a las circunstancias, casualidades controladas, que rodean su construcción, se produce estrictamente cuando rastreamos aquellos invariantes que se mantienen en las dos versiones y las reconcilian. En este corto período de tiempo se producen en el proyecto una serie de decisiones que permiten descubrir, tanto en la forma como en el mismo proceso transformador del proyecto, en su obsesivo registro, en los nuevos referentes asumidos y propuestos, la primera visibilidad del cambio del paradigma moderno. Pero este momento germinal que cristaliza el paso a la postmodernidad no es inédito en la historia de la arquitectura americana. Así, el relato abre su ámbito temporal hasta un nuevo período de cincuenta años que arranca en 1893, año de la celebración en Chicago de la Exposición Internacional Colombina. En la White City de Hunt & McKim y del traidor Burham, Louis Sullivan construye su Golden Doorway en el pabellón de los Transportes. Aquella que visitará Adolf Loos antes de volver, renovado, a Viena; la misma que admirará André Bouillet, representante de la Union Centrale des Arts Decoratifs de Paris, y que deslumbrará en los museos de toda Europa, de París a Moscú en grandes fotografías y maquetas. Hasta que en Finlandia alguien muestra una de esas fotografías a un joven estudiante de diecinueve años en el Instituto Politécnico. Eliel Saarinen queda fascinado por la poderosa novedad de la imagen. Cuelga la fotografía frente a su tablero de dibujo, consciente de que la Golden Doorway, esa puerta de la aventura y la catarsis que Sullivan acuñaría como distintivo y que resolvería como único elemento complejo sus proyectos más maduros, desprovistos de todo ornamento; la misma que repetirían más tarde, con profundo reconocimiento, Ladovsky, Wright, Scarpa o Moneo, puerta dentro de puerta, fuelle y umbral, contenía, en sus propias palabras emocionadas, todo el futuro de la arquitectura. Desde ahí, pasando por el año 1910, momento de la huida de Wright a La Toscana y el descubrimiento de su arquitectura en Europa, entre otros por un joven Mies van der Rohe, meritorio en el estudio de Peter Behrens, a través del Wasmuth Portfolio; y así como algo después, en 1914, Schindler y en 1923 Neutra, harán el camino inverso, hasta que Mies les siga en 1937, animado por un Philip Johnson que había viajado a Europa en 1930, volviendo a 1945 y el inicio del programa Case Study House en California, hasta 1949, momento de la construcción de la CSH#8, y, por fin, al año 1955, after 5 years of living, en el que Julius Shulman fotografía la casa de Ray y Charles Eames en el prado de Chautauqua sobre las Pacific Palisades de Los Angeles, lanzando sus finas líneas amarillas hasta Alison y Peter Smithson y su tardomoderno heroico, hasta el primer Foster y su poético hightech y hasta el O-riginal Ghery, deconstruyendo el espacio esencial de su casa desde el espacio mismo, abiertas ya las puertas al nuevo siglo. Y en estos cambios de paradigma, desde el rígido eclecticismo de los estilos al lirismo moderno en el gozne secular y de ahí a la frivolidad, ligereza, exhibicionismo y oportunismo cultos del hecho postmoderno, hay algo que se mantiene invariante en los bandazos de la relación del hombre contemporáneo con su entorno. Como la escultura, que según Barnett Newman no es sino aquello contra lo que uno choca cuando retrocede para mirar un cuadro, en estos prístinos lugares, comunes y corrientes, recorrido, puerta, umbral, recinto y vacío, te topas con la arquitectura antes de darte cuenta de que es arquitectura. ABSTRACT As with many other projects, the origin of this doctoral thesis is the result of a chance. A few years ago I found in a bookstore in London, 38 Harmood st., Walden Books, a first edition of the well-known monograph about Mies by Philip Johnson. The tiny book, in fact a catalog of the exhibition that the MoMA of New York devoted to the work of Mies van der Rohe in 1947, ten years after his landing in the United States, has a size of 10 x 7.5 inches, that is, half of Crown American format (20 x 15 inches), equivalent to 508 x 381 mm. In the first printing, published by The Plantin Press, 12,000 copies were released. That same year, produced by Reynal and Hitchcock, both the first English translation of When the cathedrals were white by Le Corbusier and a selection of poems by Lorca were published, seven years after his Poet in New York. Inside the book, the famous drawing from Mies Sketch for a glass house on a hillside c. 1934 appears on page 109, barely a few lines, precise and nuanced though, the house on a hillside that quickly reminds us of the proposals of Eero Saarinen for a house in the air, first in 1941, in Pennsylvania, and later, in 1945, with Charles Eames, in Los Angeles, that would never be built, but in their later alliterations made by Harry Seidler (Julian Rose House, Wahroonga, Sydney, 1949), Philip Johnson (Leonhardt house, Long Island, New York, 1956) or Craig Ellwood (Smith House, Crestwood Hills, 1958; Frank Pierson & Polly House, Malibu, 1962, Chamorro House, Hollywood Hills, 1963, or the Weekend House series, with Gerald Horn, between 1964 and 1970, to the magnificent Art Center College of Design Pasadena, the inhabited bridge, in 1977). The story that gives rise to the text flows in a short amount of time, from the first drawings of the Case Study House No. 8, within the program promoted by John Entenza and his magazine Arts & Architecture in California, made in the study of Saarinen in Bloomfield Hills, Michigan, until the project of the Eames house is completed five years after finishing the construction in 1955, in the final version we know, radically different from the initial state, when the couple, Charles and Ray, published the film House after Five Years of Living. The original discussion around this house, or better, about the circumstances, controlled coincidences, regarding its construction, appears when one takes account of those that remain, the invariants, in the two versions, drawn and built, which precisely allow the reconciliation between both projects. In this short period of time a series of decisions made in the transformation process of the project reveal, in the obsessive record made by Charles Eames and in the new proposed references, the first visibility of the changing of the modern paradigm. But this germinal moment that crystallizes the transition to postmodernism is not unprecedented in the history of American architecture. So, the story opens its temporal scope to a fifty-year period that started in 1893, date of the celebration of the Chicago World´s Columbian Exposition. In the White City by Hunt & McKim and Burnham, the traitor, Louis Sullivan builds his Golden Doorway in the Transportation Building. That visited by a renovated Adolf Loos before his coming back to Vienna; the same that André Bouillet, Head of the Union Centrale des Arts Decoratifs in Paris, admired and dazzled in museums all over Europe, from Paris to Moscow, in large photographs and models. Until someone in Finland showed one of those photos to a young nineteen-years-old student at the Polytechnic Institute. Eliel Saarinen became fascinated by the powerful new image: he hanged the picture in front of his drawing board, aware that the Golden Doorway, that door of adventure and catharsis Sullivan coined as distinctive and as a single complex element which would solve their most mature projects, devoid of all ornament; the same that would repeat later, with deep appreciation, Ladovsky, Wright, Scarpa, or Moneo, a door inside a door, a threshold, a gap that contained, in its own moving words, the whole future of architecture. From there, through 1910, when Wright's flight to Tuscany allows Europe to discover his architecture, including a young Mies van der Rohe, meritorious in the studio of Peter Behrens, via the Wasmuth Portfolio; and as a little bit later, in 1914, Schindler and Neutra in 1923, made the travel in opposite direction, until Mies follows them in 1937, led by a Philip Johnson who had traveled to Europe in 1930, we return to 1945 and the beginning of the program Case Study House in California, and from 1949, when construction of the CSH # 8 begins, and finally, to 1955, after five years of living, when Julius Shulman photographs the inside of the house with Ray and Charles Eames, and all their belongins, at the Chautauqua meadows on Pacific Palisades in Los Angeles, launching its fine yellow lines to Alison and Peter Smithson and his heroic late modern, up to the first Foster and his poetic hightech and even the O-riginal Gehry, deconstructing the essential space of his home from the space itself, opening the doors to the new century. And these paradigm shifts, from the hard eclectic styles to modern secular lyricism in the hinge and then overcoming the cultured frivolity, lightness, exhibitionism, and opportunism of the postmodern skeptical focus, something remains intense, invariant in the lurching relationship of contemporary man and his environment. As the sculpture, which according to Barnett Newman is what you bump into when you back up to see a painting, in these pristine, ordinary places, promenade, door, threshold, enclosure and emptiness, you stumble upon the architecture even before realizing that it is architecture.

Crystal structure of the HLA-Cw3 allotype-specific killer cell inhibitory receptor KIR2DL2

Killer cell inhibitory receptors (KIR) protect class I HLAs expressing target cells from natural killer (NK) cell-mediated lysis. To understand the molecular basis of this receptor-ligand recognition, we have crystallized the extracellular ligand-binding domains of KIR2DL2, a member of the Ig superfamily receptors that recognize HLA-Cw1, 3, 7, and 8 allotypes. The structure was determined in two different crystal forms, an orthorhombic P212121 and a trigonal P3221 space group, to resolutions of 3.0 and 2.9 Å, respectively. The overall fold of this structure, like KIR2DL1, exhibits K-type Ig topology with cis-proline residues in both domains that define β-strand switching, which sets KIR apart from the C2-type hematopoietic growth hormone receptor fold. The hinge angle of KIR2DL2 is approximately 80°, 14° larger than that observed in KIR2DL1 despite the existence of conserved hydrophobic residues near the hinge region. There is also a 5° difference in the observed hinge angles in two crystal forms of 2DL2, suggesting that the interdomain hinge angle is not fixed. The putative ligand-binding site is formed by residues from several variable loops with charge distribution apparently complementary to that of HLA-C. The packing of the receptors in the orthorhombic crystal form offers an intriguing model for receptor aggregation on the cell surface.