ELECTRODEPOSITION OF PLATINUM PARTICLES ON GLASSY-CARBON MODIFIED WITH COBALT PORPHYRIN AND NAFION FILM AND THEIR ELECTROCATALYTIC REDUCTION OF DIOXYGEN

In this paper, five types of chemically modified electrode (CMEs) prepared with the deposition of platinum particles on various surfaces of glassy carbon (GC) modified with cobalt porphyrin and Nafion(R) solution are characterized using the electron scanning microscope (SEM). Their activities in the four-electron reduction of dioxygen to water on the basis of their electrochemical data from cyclic voltammetric and rotating ring-disk electrode (RRDE) experiments are examined and compared. Platinum particles dispersed on the GC surface adsorbed with the cobalt porphyrin exhibit the highest activity for the electrocatalytic reduction of dioxygen. However it is interesting that the cobalt ion is lost from the center of the porphyrin ring during the preparation of the cobalt porphyrin + Nafion mixture solution, while the porphyrin ring still remains in the Nafion film, as shown by EDX analysis. The incorporation of the porphyrin may change the structure of the Nafion film into a looser form, since the platinum particles dispersed in the film are more readily exposed, resulting in more favourable mass transfer and higher activity for the electrocatalytic reduction of dioxygen.

ELECTRODEPOSITION OF POLYCRYSTALLINE CD-RICH HG1-XCDXTE AND PHOTOELECTRO-CHEMICAL BEHAVIOR OF HG0.09CD0.91TE THIN-FILM

Electrodeposition process of polycrystalline Cd-rich Hg_(1-z)Cd_xTe (x>0.5) in acidic bath of CdSO_4+HTeO_2~+HgCl_2 was investigated. The simultaneous electrodeposition technique of three kinds of ions at the same potential has been achieved. The XRD, SEM and EDAX analysis of the thin film electrodeposited on titanium substrate showed a typical cubic zinc blende polycrystalline structure and homogeneous dispersion. The photoelectrochemical behavior of (1-x)=0.09 polycrystalline thin film in a polysulfide re...

Report for the British Board of Film Classification on viewers of the Lord of the Rings, aged under 16

This is a report on what can be learnt from our world dataset about viewers of The Lord of the Rings who were aged under 16. In this report, I draw both on the world set, and on the UK subset, sometimes drawing comparisons between them. The reason for using both is that, obviously, the world set is so much larger (comprising 24,739 in toto, with 2475 under 16), but the UK set (comprising 3115 in toto, and 306 under 16s) allows us to explore both some of the specificities of responses here, the qualitative meaning of some responses (given we worked in 14 languages, many are inaccessible to us for analysis), and of course their relations to the quantitative patterns that emerge.

Beyond simple imaging with energetic beams – nanopatterning, correlative microscopy and statistical analysis of inclusions

Electron microscopy (EM) has advanced in an exponential way since the first transmission electron microscope (TEM) was built in the 1930’s. The urge to ‘see’ things is an essential part of human nature (talk of ‘seeing is believing’) and apart from scanning tunnel microscopes which give information about the surface, EM is the only imaging technology capable of really visualising atomic structures in depth down to single atoms. With the development of nanotechnology the demand to image and analyse small things has become even greater and electron microscopes have found their way from highly delicate and sophisticated research grade instruments to key-turn and even bench-top instruments for everyday use in every materials research lab on the planet. The semiconductor industry is as dependent on the use of EM as life sciences and pharmaceutical industry. With this generalisation of use for imaging, the need to deploy advanced uses of EM has become more and more apparent. The combination of several coinciding beams (electron, ion and even light) to create DualBeam or TripleBeam instruments for instance enhances the usefulness from pure imaging to manipulating on the nanoscale. And when it comes to the analytic power of EM with the many ways the highly energetic electrons and ions interact with the matter in the specimen there is a plethora of niches which evolved during the last two decades, specialising in every kind of analysis that can be thought of and combined with EM. In the course of this study the emphasis was placed on the application of these advanced analytical EM techniques in the context of multiscale and multimodal microscopy – multiscale meaning across length scales from micrometres or larger to nanometres, multimodal meaning numerous techniques applied to the same sample volume in a correlative manner. In order to demonstrate the breadth and potential of the multiscale and multimodal concept an integration of it was attempted in two areas: I) Biocompatible materials using polycrystalline stainless steel and II) Semiconductors using thin multiferroic films. I) The motivation to use stainless steel (316L medical grade) comes from the potential modulation of endothelial cell growth which can have a big impact on the improvement of cardio-vascular stents – which are mainly made of 316L – through nano-texturing of the stent surface by focused ion beam (FIB) lithography. Patterning with FIB has never been reported before in connection with stents and cell growth and in order to gain a better understanding of the beam-substrate interaction during patterning a correlative microscopy approach was used to illuminate the patterning process from many possible angles. Electron backscattering diffraction (EBSD) was used to analyse the crystallographic structure, FIB was used for the patterning and simultaneously visualising the crystal structure as part of the monitoring process, scanning electron microscopy (SEM) and atomic force microscopy (AFM) were employed to analyse the topography and the final step being 3D visualisation through serial FIB/SEM sectioning. II) The motivation for the use of thin multiferroic films stems from the ever-growing demand for increased data storage at lesser and lesser energy consumption. The Aurivillius phase material used in this study has a high potential in this area. Yet it is necessary to show clearly that the film is really multiferroic and no second phase inclusions are present even at very low concentrations – ~0.1vol% could already be problematic. Thus, in this study a technique was developed to analyse ultra-low density inclusions in thin multiferroic films down to concentrations of 0.01%. The goal achieved was a complete structural and compositional analysis of the films which required identification of second phase inclusions (through elemental analysis EDX(Energy Dispersive X-ray)), localise them (employing 72 hour EDX mapping in the SEM), isolate them for the TEM (using FIB) and give an upper confidence limit of 99.5% to the influence of the inclusions on the magnetic behaviour of the main phase (statistical analysis).

Experimental and modeling analysis of the reliability of the anisotropic conductive films

Experiments as well as computer modeling methods have been used to investigate the effect of the solder reflow process on the electrical characteristics and reliability of anisotropic conductive film (ACF) interconnections. In the experiments, the contact resistance of the ACF interconnections was found to increase after a subsequent reflow and the magnitude of this increase was strongly correlated to the peak temperature of the reflow profile. In fact, nearly 40 percent of the joints were opened (i.e. lifted away from the pad) after the reflow with a peak temperature of 260 OC while no openings was observed when the peak temperature was 210 "C. It is believed that the CTE mismatch between the polymer particle and the adhesive matrix is the main cause of this contact degradation. To understand this phenomenon better, a 3-D model of an ACF joint structure was built and Finite Element Analysis was used to predict the stress distrihution in the conductive particles, adhesive matrix and metal pads during the reflow process. The effects of the peak temperature, the CTE of the adhesive matrix and the bump height on the reliability of the ACF interconnections were discussed.

Macro-Micro Modelling Analysis for High Density Packaged Flip Chips

A wide range of flip chip technologies with solder or adhesives have become dominant solutions for high density packaging applications due to the excellent electrical performance, high I/O density and good thermal performance. This paper discusses the use of modeling technique to predict the reliability of high density packaged flip chips in the humid environment. Reliability assessment is discussed for flip chip package at ultra-fine pitch with anisotropic conductive film (ACF). The purpose of this modeling work is to understand the role that moisture plays in the failure of ACF flip chips. A macro-micro 3D finite element modeling technique was used in order to make the multi-length-scale modeling of the ACF flip chip possible. Modeling results are consistent with the findings in the experimental work

An analysis of a microfabricated solenoid inductor

A microscale solenoid inductor is manufactured using electrodeposition method. The inductor is designed for switching mode DC-DC converters operating at switching frequencies in the mega-Hertz range. Two magnetic core materials, electroformed permalloy Ni80 Fe20 film and Vitrovac 6025 which is a commercial magnetic film, have been analyzed using experimental and computer modeling techniques

Role of bonding time and temperature on the physical properties of coupled anisotropic conductive–nonconductive adhesive film for flip chip on glass technology

Using thermosetting epoxy based conductive adhesive films for the flip chip interconnect possess a great deal of attractions to the electronics manufacturing industries due to the ever increasing demands for miniaturized electronic products. Adhesive manufacturers have taken many attempts over the last decade to produce a number of types of adhesives and the coupled anisotropic conductive-nonconductive adhesive film is one of them. The successful formation of the flip chip interconnection using this particular type of adhesive depends on, among factors, how the physical properties of the adhesive changes during the bonding process. Experimental measurements of the temperature in the adhesive have revealed that the temperature becomes very close to the required maximum bonding temperature within the first 1s of the bonding time. The higher the bonding temperature the faster the ramp up of temperature is. A dynamic mechanical analysis (DMA) has been carried out to investigate the nature of the changes of the physical properties of the coupled anisotropic conductive-nonconductive adhesive film for a range of bonding parameters. Adhesive samples that are pre-cured at 170, 190 and 210°C for 3, 5 and 10s have been analyzed using a DMA instrument. The results have revealed that the glass transition temperature of this type of adhesive increases with the increase in the bonding time for the bonding temperatures that have been used in this work. For the curing time of 3 and 5s, the maximum glass transition temperature increases with the increase in the bonding temperature, but for the curing time of 10s the maximum glass transition temperature has been observed in the sample which is cured at 190°C. Based on these results it has been concluded that the optimal bonding temperature and time for this kind of adhesive are 190°C and 10s, respectively.

English Channel towed sledge seabed images. Phase 2: Analysis of selected tow images

During the 1970s and 1980s, the late Dr Norman Holme undertook extensive towed sledge surveys in the English Channel and some in the Irish Sea. Only a minority of the resulting images were analysed and reported before his death in 1989 but logbooks, video and film material has been archived in the National Marine Biological Library (NMBL) in Plymouth. A study was therefore commissioned by the Joint Nature Conservation Committee and as a part of the Mapping European Seabed Habitats (MESH) project to identify the value of the material archived and the procedure and cost to undertake further work (Phase 1 of the study reported here: Oakley & Hiscock, 2005). Some image analysis was undertaken as a part of Phase 1. Phase 2 (this report) was to further analyse selected images. Having determined in Phase 1 that only the 35 mm photographic transparencies provided sufficient clarity to identify species and biotopes, the tows selected for analysis were ones where 35mm images had been taken. The tows selected for analysis of images were mainly in the vicinity of Plymouth and especially along the area between Rame Head and the region of the Eddystone. The 35 mm films were viewed under a binocular microscope and the taxa that could be recognised recorded in note form. Twenty-five images were selected for inclusion in the report. Almost all of the images were of level sediment seabed. Where rocks were included, it was usually unplanned and the sled was hauled before being caught or damaged. The main biotopes or biotope complexes identified were: SS.SMU.CSaMu. Circalittoral sandy mud. Extensively present between the shore and the Eddystone Reef complex and at depths of about 48 to 52 m. At one site offshore of Plymouth Sound, the turret shell Turritella communis was abundant. In some areas, this biotope had dense anemones, Mesacmaea mitchelli and (more rarely) Cerianthus lloydii. Queen scallops, Aequipecten opercularis and king scallops, Pecten maximus, were sometimes present in small numbers. Hard substratum species such as hydroids, dead mens fingers Alcyonium digitatum and the cup coral Caryophyllia smithii occurred in a few places, probably attached to shells or stones beneath the surface. South of the spoil ground off Hilsea Point at 57m depth, the sediment was muddier but is still assigned to this biotope complex. It is notable that three small sea pens, most likely Virgularia mirabilis, were seen here. SS.SMx.CMx. Circalittoral mixed sediment. Further offshore but at about the same depth as SS.SMU.CSaMu occurred, coarse gravel with some silt was present. The sediment was characterised must conspicuously by small queen scallops, Aequipecten opercularis. Peculiarly, there were ‘bundles’ of the branching bryozoan Cellaria sp. – a species normally found attached to rock. It could not be seen whether these bundles of Cellaria had been brought-together by terebellid worms but it is notable that Cellaria is recorded in historical surveys. As with many other sediments, there were occasional brittle stars, Ophiocomina nigra and Ophiura ophiura. Where sediments were muddy, the burrowing anemone Mesacmaea mitchelli was common. Where pebbles or cobbles occurred, there were attached species such as Alcyonium digitatum, Caryophyllia smithii and the fleshy bryozoan Alcyonidium diaphanum. Undescribed biotope. Although most likely a part of SS.SMx.CMx, the biotope visually dominated by a terebellid worm believed to be Thelepus cincinnatua, is worth special attention as it may be an undescribed biotope. The biotope occurred about 22 nautical miles south of the latitude of the Eddystone and in depths in excess of 70 m. SS.SCS.CCS.Blan. Branchiostoma lanceolatum in circalittoral coarse sand with shell gravel at about 48m depth and less. This habitat was the ‘classic’ ‘Eddystone Shell Gravel’ which is sampled for Branchiostoma lanceolatum. However, no Branchiostoma lanceolatum could be seen. The gravel was almost entirely bare of epibiota. There were occasional rock outcrops or cobbles which had epibiota including encrusting calcareous algae, the sea fan Eunicella verrucosa, cup corals, Caryophyllia smithii, hydroids and a sea urchin Echinus esculentus. The variety of species visible on the surface is small and therefore identification to biotope not usually possible. Historical records from sampling surveys that used grabs and dredges at the end of the 19th century and early 20th century suggest similar species present then. Illustrations of some of the infaunal communities from work in the 1920’s is included in this report to provide a context to the epifaunal photographs.

English Channel towed sledge seabed images. Phase 1: scoping study and example analysis

During the 1970’s and 1980’s, the late Dr Norman Holme undertook extensive towed sledge surveys in the English Channel and some in the Irish Sea. Only a minority of the resulting images were analysed and reported before his death in 1989 but logbooks, video and film material has been archived in the National Marine Biological Library (NMBL) in Plymouth. A scoping study was therefore commissioned by the Joint Nature Conservation Committee and as a part of the Mapping European Seabed Habitats (MESH) project to identify the value of the material archived and the procedure and cost to undertake further work. The results of the scoping study are: 1. NMBL archives hold 106 videotapes (reel-to-reel Sony HD format) and 59 video cassettes (including 15 from the Irish Sea) in VHS format together with 90 rolls of 35 mm colour transparency film (various lengths up to about 240 frames per film). These are stored in the Archive Room, either in a storage cabinet or in original film canisters. 2. Reel-to-reel material is extensive and had already been selectively copied to VHS cassettes. The cost of transferring it to an accepted ‘long-life’ medium (Betamax) would be approximately £15,000. It was not possible to view the tapes as a suitable machine was not located. The value of the tapes is uncertain but they are likely to become beyond salvation within one to two years. 3. Video cassette material is in good condition and is expected to remain so for several more years at least. Images viewed were generally of poor quality and the speed of tow often makes pictures blurred. No immediate action is required. 4. Colour transparency films are in good condition and the images are very clear. They provide the best source of information for mapping seabed biotopes. They should be scanned to digital format but inexpensive fast copying is problematic as there are no between-frame breaks between images and machines need to centre the image based on between-frame breaks. The minimum cost to scan all of the images commercially is approximately £6,000 and could be as much as £40,000 on some quotations. There is a further cost in coding and databasing each image and, all-in-all it would seem most economic to purchase a ‘continuous film’ scanner and undertake the work in-house. 5. Positional information in ships logs has been matched to films and to video tapes. Decca Chain co-ordinates recorded in the logbooks have been converted to latitude and longitude (degrees, minutes and seconds) and a further routine developed to convert to degrees and decimal degrees required for GIS mapping. However, it is unclear whether corrections to Decca positions were applied at the time the position was noted. Tow tracks have been mapped onto an electronic copy of a Hydrographic Office chart. 6. The positions of start and end of each tow were entered to a spread sheet so that they can be displayed on GIS or on a Hydrographic Office Chart backdrop. The cost of the Hydrographic Office chart backdrop at a scale of 1:75,000 for the whole area was £458 incl. VAT. 7. Viewing all of the video cassettes to note habitats and biological communities, even by an experienced marine biologist, would take at least in the order of 200 hours and is not recommended. English Channel towed sledge seabed images. Phase 1: scoping study and example analysis. 6 8. Once colour transparencies are scanned and indexed, viewing to identify seabed habitats and biological communities would probably take about 100 hours for an experienced marine biologist and is recommended. 9. It is expected that identifying biotopes along approximately 1 km lengths of each tow would be feasible although uncertainties about Decca co-ordinate corrections and exact positions of images most likely gives a ±250 m position error. More work to locate each image accurately and solve the Decca correction question would improve accuracy of image location. 10. Using codings (produced by Holme to identify different seabed types), and some viewing of video and transparency material, 10 biotopes have been identified, although more would be added as a result of full analysis. 11. Using the data available from the Holme archive, it is possible to populate various fields within the Marine Recorder database. The overall ‘survey’ will be ‘English Channel towed video sled survey’. The ‘events’ become the 104 tows. Each tow could be described as four samples, i.e. the start and end of the tow and two areas in the middle to give examples along the length of the tow. These samples would have their own latitude/longitude co-ordinates. The four samples would link to a GIS map. 12. Stills and video clips together with text information could be incorporated into a multimedia presentation, to demonstrate the range of level seabed types found along a part of the northern English Channel. More recent images taken during SCUBA diving of reef habitats in the same area as the towed sledge surveys could be added to the Holme images.

Analysis about the society of 'Pa Negre' (Agustí Villaronga, 2010)

This article has developed with the intention of analyzing how the stereotypes, prejudices and lies can influence the education of the children. Formation, that usually comes from family and teachers, who sometimes move for extremist ideologies. There exist multiple fictions in which we observe these social archetypes, but it is the case of the movie Pa negre (Agustí Villaronga, 2010), where the principal personage evolves psychologically, because of that its eyes observe and the ideas that the people transmit him on its family, in the rural environments, where the tradition of the rumors coexists.

Thickness-induced stabilization of ferroelectricity in SrRuO3/Ba0.5Sr0.5TiO3/Au thin film capacitors

Pulsed-laser deposition has been used to fabricate Au/Ba0.5Sr0.5TiO3/SrRuO3/MgO thin film capacitor structures. Crystallographic and microstructural investigations indicated that the Ba0.5Sr0.5TiO3 (BST) had grown epitaxially onto the SrRuO3 lower electrode, inducing in-plane compressive and out- of-plane tensile strain in the BST. The magnitude of strain developed increased systematically as film thickness decreased. At room temperature this composition of BST is paraelectric in bulk. However, polarization measurements suggested that strain had stabilized the ferroelectric state, and that the decrease in film thickness caused an increase in remanent polarization. An increase in the paraelectric-ferroelectric transition temperature upon a decrease in thickness was confirmed by dielectric measurements. Polarization loops were fitted to Landau-Ginzburg-Devonshire (LGD) polynomial expansion, from which a second order paraelectric-ferroelectric transition in the films was suggested at a thickness of similar to500 nm. Further, the LGD analysis showed that the observed changes in room temperature polarization were entirely consistent with strain coupling in the system. (C) 2002 American Institute of Physics.

Understanding thickness effects in thin film capacitors

Pulsed Laser Deposition (PLD) was used to make Au/(Ba0.5Sr0.5)TiO3/(La0.5Sr0.5) CoO3/MgO thin film capacitor structures. Functional properties were studied with changing BST thickness from similar to1265 nm to similar to63 nm. The dielectric constant was found to decrease, and migration of T-m (the temperature at which the dielectric constant is maximum) to lower temperatures occurred as thickness was reduced. Curie-Weiss plots of the as-obtained dielectric data, indicated that the Curie temperature was also systemmatically progressively depressed. Further, fitting to expressions previously used to describe diffuse phase transitions suggested increased diffuseness in transformation behaviour as film thickness decreased. This paper discusses the care needed in interpreting the observations given above. We make particular distinction between the apparent Curie-temperature derived from Curie-Weiss plots of as-measured data, and the inherent Curie temperature determined after correction for the interfacial capacitance. We demonstrate that while the apparent Curie temperature decreases as thickness decreases, the inherent Curie temperature is thickness independent. Thickness-invariant phase transition behaviour is confirmed from analysis of polarisation loops, and from examination of the temperature dependence of the loss-tangent. We particularly note that correction of data for interfacial capacitance does not alter the position of T-m. We must therefore conclude that the position of T-m is not related simply to phase transformation behaviour in BST thin films.

Funding, ideology and the aesthetics of the development film in postcolonial Zimbabwe

This article considers the relationships between aesthetics and ideology in donor-funded ‘development’ film-making from Zimbabwe, examining in particular how the films’ producers have attempted to popularize a genre of film-making that has its roots in colonial cinema. Making close reference to two productions from the Harare-based Media for Development Trust (MFD) – Neria (Godwin Mawaru, 1992), and Everyone’s Child (Tsitsi Dangarembga, 1996) (both of which may be regarded as archetypal examples of their genre) – the article demonstrates how the films deploy a range of aesthetic strategies to imbue a set of narratives drawn from colonial development films with greater impact and cultural resonance for contemporary local audiences. The article also suggests that close analysis of these strategies may provide insights into the relationships between the films’ aesthetic dimensions and wider ideological issues in the region.

Quantitative analysis of proton imaging measurements of laser-induced plasmas

A method for obtaining quantitative information about electric field and charge distributions from proton imaging measurements of laser-induced plasmas is presented. A parameterised charge distribution is used as target plasma. The deflection of a proton beam by the electric field of such a plasma is simulated numerically as well as the resulting proton density, which will be obtained on a screen behind the plasma according to the proton imaging technique. The parameters of the specific charge distributions are delivered by a combination of linear regression and nonlinear fitting of the calculated proton density distribution to the measured optical density of a radiochromic film screen changed by proton exposure. It is shown that superpositions of spherical Gaussian charge distributions as target plasma are sufficient to simulate various structures in proton imaging measurements, which makes this method very flexible.