Curvature and velocity of methane-air Bunsen flame tips.

PIV and photographic recording are used to measure the velocity of the fresh gas and the shape of the reaction layer in a region around the tip of a methane-air Bunsen flame attached to a cylindrical burner. The results compare well with numerical simulations carried out with an infinite activation energy reaction model. The experimental and numerical results confirm that the well-known linear relation between flame velocity and flame stretch derived from asymptotic theory for weakly curved and strained flames is valid for small and moderate values of the flame stretch if the modified definition of stretch introduced by Echekki and Mungal (Proc Combust Inst 23:455–461, 1990) and Poinsot et al. (Combust Sci Technol 81:45–73, 1992) is used. However, the relation between flame velocity and modified stretch ceases to be linear and approaches a square root law for large values of the stretch, when the curvature of the flame tip becomes large compared to the inverse of the thickness of a planar flame.

Impact of N2 plasma power and duration on AlGaN/GaN HEMT

urface treatments have been recently shown to play an active role in electrical characteristics in AlGaN/GaN HEMTs, in particular during the passivation processing [1-4]. However, the responsible mechanisms are partially unknown and further studies are demanding. The effects of power and time N2 plasma pre-treatment prior to SiN deposition using PE-CVD (plasma enhanced chemical vapour deposition) on GaN and AlGaN/GaN HEMT have been investigated. The low power (60 W) plasma pre-treatment was found to improve the electronic characteristics in GaN based HEMT devices, independently of the time duration up to 20 min. In contrast, high power (150 and 210 W) plasma pretreatment showed detrimental effects in the electronic properties (Fig. 1), increasing the sheet resistance of the 2DEG, decreasing the 2DEG charge density in AlGaN/GaN HEMTs, transconductance reduction and decreasing the fT and fmax values up to 40% respect to the case using 60 W N2 plasma power. Although AFM (atomic force microscopy) results showed AlGaN and GaN surface roughness is not strongly affected by the N2-plasma, KFM (Kelvin force microscopy) surface analysis shows significant changes in the surface potential, trending to increase its values as the plasma power is higher. The whole results point at energetic ions inducing polarization-charge changes that affect dramatically to the 2-DEG charge density and the final characteristics of the HEMT devices. Therefore, we conclude that AlGaN surface is strongly sensitive to N2 plasma power conditions, which turn to be a key factor to achieve a good surface preparation prior to SiN passivation.

Curvature and velocity of methane-air Bunsen flame tips

PIV and photographic recording are used to measure the velocity of the fresh gas and the shape of the reaction layer in a region around the tip of a methane- air Bunsen flame attached to a cylindrical burner. The results compare well with numerical simulations carried out with an infinite activation energy reaction model. The experimental and numerical results confirm that the well-known linear relation between flame velocity and flame stretch derived from asymptotic theory for weakly curved and strained flames is valid for small and moderate values of the flame stretch if the modified definition of stretch introduced by Echekki and Mungal (Proc Combust Inst 23:455–461,1990) and Poinsot et al. (Combust Sci Technol 81:45–73,1992) is used. However, the relation between flame velocity and modified stretch ceases to be linear and approaches a square root law for large values of the stretch, when the curvature of the flame tip becomes large compared to the inverse of the thickness of a planar flame

STC power for 15MW of PV comparing nameplate, initial power and power after 4 years

To date, the majority of quality controls performed at PV plants are based on the measurement of a small sample of individual modules. Consequently, there is very little representative data on the real Standard Test Conditions (STC) power output values for PV generators. This paper presents the power output values for more than 1300 PV generators having a total installed power capacity of almost 15.3 MW. The values were obtained by the INGEPER-UPNA group, in collaboration with the IES-UPM, through a study to monitor the power output of a number of PV plants from 2006 to 2009. This work has made it possible to determine, amongst other things, the power dispersion that can be expected amongst generators made by different manufacturers, amongst generators made by the same manufacturer but comprising modules of different nameplate ratings and also amongst generators formed by modules with the same characteristics. The work also analyses the STC power output evolution over time in the course of this 4-year study. The values presented here could be considered to be representative of generators with fault-free modules.

Effect of strain and magnetic field on the critical current and electric resistance of the joints between HTS coated conductors

Engineering of devices and systems such as magnets, fault current limiters or cables, based on High Temperature Superconducting wires requires a deep characterization of the possible degradation of their properties by handling at room temperature as well as during the service life thus establishing the limits for building up functional devices and systems. In the present work we report our study regarding the mechanical behavior of spliced joints between commercial HTS coated conductors based on YBCO at room temperature and service temperature, 77 K. Tensile tests under axial stress and the evolution of the critical current and the electric resistance of the joints have been measured. The complete strain contour for the tape and the joint has been obtained by using Digital Image Correlation. Also, tensile tests under external magnetic field have been performed and the effect of the applied field on the critical current and the electric resistance of the joints has been studied. Finally, a preliminary numerical study by means of Finite Element Method (FEM) of the mechanical behavior of the joints between commercial HTS is presented.

Effect of strain and magnetic field on the critical current and electric resistance of the joints between HTS coated conductors

Engineering of devices and systems such as magnets, fault current limiters or cables, based on High Temperature Superconducting wires requires a deep characterization of the possible degradation of their properties by handling at room temperature as well as during the service life thus establishing the limits for building up functional devices and systems. In the present work we report our study regarding the mechanical behavior of spliced joints between commercial HTS coated conductors based on YBCO at room temperature and service temperature, 77 K. Tensile tests under axial stress and the evolution of the critical current and the electric resistance of the joints have been measured. The complete strain contour for the tape and the joints has been obtained by using Digital Image Correlation. Also, tensile tests under external magnetic field have been performed and the effect of the applied field on the critical current and the electric resistance of the joints has been studied. Additionally, fatigue tests under constant cyclic stress and loading-unloading ramps have been carried out in order to evaluate the electromechanical behavior of the joints and the effect of maximum applied stress on the critical current. Finally, a preliminary numerical study by means of the Finite Element Method (FEM) of the electromechanical behavior of the joints between commercial HTS is presented.

Study of a-Si crystallization dependence on power and irradiation time using a CW green laser

An advantage of laser crystallization over conventional heating methods is its ability to limit rapid heating and cooling to thin surface layers. Laser energy is used to heat the a-Si thin film to change the microstructure to poly-Si. Thin film samples of a-Si were irradiated with a CW-green laser source. Laser irradiated spots were produced by using different laser powers and irradiation times. These parameters are identified as key variables in the crystallization process. The power threshold for crystallization is reduced as the irradiation time is increased. When this threshold is reached the crystalline fraction increases lineally with power for each irradiation time. The experimental results are analysed with the aid of a numerical thermal model and the presence of two crystallization mechanisms are observed: one due to melting and the other due to solid phase transformation.