Using a Double-pass solar drier for drying of bamboo shoots

Three different drying methods, a forced convection double-pass solar drier (DPSD), typical cabinet type natural convection solar drier (CD) and traditional open-sun drying (OSD) were used for draying of bamboo shoots in central Vietnam. During drying the operational parameters such as drying temperature, relative humidity, air velocity, insolation and water evaporation have been recorded hourly. The mean drying temperatures and relative humidity in the drying chamber were 55.2°C, 23.7%; 47.5°C, 37,6%; 36.2°C, 47.8% in DPSD, CD and OSD, respectively. The mean global radiation during all experimental runs was 670 Wm^−2. The result also shows that fastest drying process was occurred in DPSD where the falling-rate period was achieved after 7 hours, in change to OSD where it took 16 hours. The overall drying efficiency was 23.11%, 15.83% and 9.73% in case of DPSD, CD and OSD, respectively. Although the construction cost of DPSD was significantly higher than in CD, the drying costs per one kilogram of bamboo shoots were by 42.8% lower in case of DPSD as compared to CD. Double-pass solar drier was found to be technically and economically suitable for drying of bamboo shoots under the specific conditions in central Vietnam and in all cases, the use of this drier led to considerable reduction in drying time in comparison to traditional open-sun drying.

Agri-environmental evaluation of traditional and alternative corn production systems in Chiapas, Mexico

This study evaluates the effects of environmental variables on traditional and alternative agroecosystems in three Ejidos (communal lands) in the Chiapas rainforest in Mexico. The tests occurred within two seasonal agricultural cycles. In spring-summer, experiments were performed with the traditional slash, fell and burn (S-F-B) system, no-burn systems and rotating systems with Mucuna deeringiana Bort., and in the autumn-winter agricultural cycle, three no-burn systems were compared to evaluate the effect of alternative sowing with corn (no-burn and topological modification of sowing). The results show a high floristic diversity in the study area (S_S = 4 - 23%), with no significant differences among the systems evaluated. In the first cycle, the analysis of the agronomical variables of the corn indicated better properties in the fallowing systems, with an average yield of 1950 kg ha^‑1, but there was variation related to the number of years left fallow. In the second cycle, the yields were positive for the alternative technology (average yield 3100 kg ha^‑1). The traditional S-F-B systems had reduced pests and increased organic matter and soil phosphorous content. These results are the consequence of fallow periods and adaptation to the environment; thus, this practice in the Chiapas rainforest constitutes an ethnocultural reality, which is unlikely to change in the near future if the agrosystems are managed based on historical principles.

Optimization of Processing Technology for Commercial Drying of Bananas (Matooke)

Summary - Cooking banana is one of the most important crops in Uganda; it is a staple food and source of household income in rural areas. The most common cooking banana is locally called matooke, a Musa sp triploid acuminate genome group (AAA-EAHB). It is perishable and traded in fresh form leading to very high postharvest losses (22-45%). This is attributed to: non-uniform level of harvest maturity, poor handling, bulk transportation and lack of value addition/processing technologies, which are currently the main challenges for trade and export, and diversified utilization of matooke. Drying is one of the oldest technologies employed in processing of agricultural produce. A lot of research has been carried out on drying of fruits and vegetables, but little information is available on matooke. Drying of matooke and milling it to flour extends its shelf-life is an important means to overcome the above challenges. Raw matooke flour is a generic flour developed to improve shelf stability of the fruit and to find alternative uses. It is rich in starch (80 - 85%db) and subsequently has a high potential as a calorie resource base. It possesses good properties for both food and non-food industrial use. Some effort has been done to commercialize the processing of matooke but there is still limited information on its processing into flour. It was imperative to carry out an in-depth study to bridge the following gaps: lack of accurate information on the maturity window within which matooke for processing into flour can be harvested leading to non-uniform quality of matooke flour; there is no information on moisture sorption isotherm for matooke from which the minimum equilibrium moisture content in relation to temperature and relative humidity is obtainable, below which the dry matooke would be microbiologically shelf-stable; and lack of information on drying behavior of matooke and standardized processing parameters for matooke in relation to physicochemical properties of the flour. The main objective of the study was to establish the optimum harvest maturity window and optimize the processing parameters for obtaining standardized microbiologically shelf-stable matooke flour with good starch quality attributes. This research was designed to: i) establish the optimum maturity harvest window within which matooke can be harvested to produce a consistent quality of matooke flour, ii) establish the sorption isotherms for matooke, iii) establish the effect of process parameters on drying characteristics of matooke, iv) optimize the drying process parameters for matooke, v) validate the models of maturity and optimum process parameters and vi) standardize process parameters for commercial processing of matooke. Samples were obtained from a banana plantation at Presidential Initiative on Banana Industrial Development (PIBID), Technology Business Incubation Center (TBI) at Nyaruzunga – Bushenyi in Western Uganda. A completely randomized design (CRD) was employed in selecting the banana stools from which samples for the experiments were picked. The cultivar Mbwazirume which is soft cooking and commonly grown in Bushenyi was selected for the study. The static gravitation method recommended by COST 90 Project (Wolf et al., 1985), was used for determination of moisture sorption isotherms. A research dryer developed for this research. All experiments were carried out in laboratories at TBI. The physiological maturity of matooke cv. mbwazirume at Bushenyi is 21 weeks. The optimum harvest maturity window for commercial processing of matooke flour (Raw Tooke Flour - RTF) at Bushenyi is between 15-21 weeks. The finger weight model is recommended for farmers to estimate harvest maturity for matooke and the combined model of finger weight and pulp peel ratio is recommended for commercial processors. Matooke isotherms exhibited type II curve behavior which is characteristic of foodstuffs. The GAB model best described all the adsorption and desorption moisture isotherms. For commercial processing of matooke, in order to obtain a microbiologically shelf-stable dry product. It is recommended to dry it to moisture content below or equal to 10% (wb). The hysteresis phenomenon was exhibited by the moisture sorption isotherms for matooke. The isoteric heat of sorption for both adsorptions and desorption isotherms increased with decreased moisture content. The total isosteric heat of sorption for matooke: adsorption isotherm ranged from 4,586 – 2,386 kJ/kg and desorption isotherm from 18,194– 2,391 kJ/kg for equilibrium moisture content from 0.3 – 0.01 (db) respectively. The minimum energy required for drying matooke from 80 – 10% (wb) is 8,124 kJ/kg of water removed. Implying that the minimum energy required for drying of 1 kg of fresh matooke from 80 - 10% (wb) is 5,793 kJ. The drying of matooke takes place in three steps: the warm-up and the two falling rate periods. The drying rate constant for all processing parameters ranged from 5,793 kJ and effective diffusivity ranged from 1.5E-10 - 8.27E-10 m2/s. The activation energy (Ea) for matooke was 16.3kJ/mol (1,605 kJ/kg). Comparing the activation energy (Ea) with the net isosteric heat of sorption for desorption isotherm (qst) (1,297.62) at 0.1 (kg water/kg dry matter), indicated that Ea was higher than qst suggesting that moisture molecules travel in liquid form in matooke slices. The total color difference (ΔE*) between the fresh and dry samples, was lowest for effect of thickness of 7 mm, followed by air velocity of 6 m/s, and then drying air temperature at 70˚C. The drying system controlled by set surface product temperature, reduced the drying time by 50% compared to that of a drying system controlled by set air drying temperature. The processing parameters did not have a significant effect on physicochemical and quality attributes, suggesting that any drying air temperature can be used in the initial stages of drying as long as the product temperature does not exceed gelatinization temperature of matooke (72˚C). The optimum processing parameters for single-layer drying of matooke are: thickness = 3 mm, air temperatures 70˚C, dew point temperature 18˚C and air velocity 6 m/s overflow mode. From practical point of view it is recommended that for commercial processing of matooke, to employ multi-layer drying of loading capacity equal or less than 7 kg/m², thickness 3 mm, air temperatures 70˚C, dew point temperature 18˚C and air velocity 6 m/s overflow mode.

Experimental and CFD study on low temperature drying of loose and compressed bulks

Die Trocknung ist eines der am häufigsten verwendeten Verfahren, um die Haltbarkeit von landwirtschaftlichen Gütern zu verlängern. Von den vielen gebräuchlichen Trocknungsarten ist die Konvektionstrocknung, die Luft als Energie- und Feuchteträger verwendet, weiterhin die wichtigste. Trotz ihrer Nachteile und ihres hohen spezifischen Energieverbrauchs sind Satztrockner für die Getreide-, Kräuter- und Heutrocknung noch weit verbreitet. Ferner werden Konvektionstrockner gemeinhin zur künstlichen Trocknung eingesetzt. Diese Arbeit ist Teil eines Forschungsprojekts, welches eine sorptionsgestützte solare Trocknung von landwirtschaftlichen Gütern untersucht. Bei dieser wird kühle feuchte Luft in Kontakt mit einer konzentrierten hygroskopischen Salzlösung gebracht. Während dieses Prozesses wird die Luft entfeuchtet und mit Hilfe der freigesetzten Verdampfungsenthalpie erwärmt. Die Anwendung dieses Verfahrens zur Trocknung landwirtschaftlicher Güter ist besonders interessant für Produkte, die bei niedrigen Temperaturen verarbeitet werden, um ihre Qualität nicht negativ zu beeinflussen. Bei allen energieintensiven Prozessen und vor allem bei der Verwendung von Solarenergie ist ein effizienter Energieverbrauch äußerst wichtig für den technischen und ökonomischen Erfolg. Eine ungleichmäßige Trocknung ist oftmals bei Satztrocknern zu beobachten, was die Energieeffizienz negativ beeinflusst. Aus diesem Grund lag im agrartechnischen Teil des Projekts der Schwerpunkt auf der Trocknung bei niedrigen Temperaturen und geringer Luftfeuchte, die der Sorptionsprozess liefert, sowie auf der Verbesserung der Luftverteilung und der Gleichmäßigkeit der Trocknung in lockeren und verdichteten Schüttungen. Es wurden Dünnschicht-Trocknungsexperminente für Blattsellerie bei unterschiedlichen Lufttemperaturen und unterschiedlicher relativer Luftfeuchte durchgeführt. Die Ergebnisse zeigen eindeutig, dass nicht nur die Lufttemperatur einen großen Einfluss auf die Trocknungsgeschwindigkeit hat, sondern auch die relative Luftfeuchte. Dies ist vor allem bei niedrigen Temperaturen, wie sie vom Sorptionssystem geliefert werden, der Fall. Um die Luftverteilung und Gleichmäßigkeit der Trocknung lockerer Schüttungen zu untersuchen, wurde ein Kistentrockner experimentell und in Strömungssimulationen getestet. Die Leistung des ursprünglichen Trockners wurde signifikant durch einfache Veränderungen des Designs verbessert. Diese stellten einen gleichmäßigeren Luftstrom durch das Produkt sicher. Die Trocknung von Heu-Rundballen stellt eine Herausforderung dar, da diese sehr stark verdichtet sind und die Dichte innerhalb eines Ballens stark schwankt. Strömungs- und Trocknungssimulationen so wie experimentelle Messungen zeigten, dass das Trocknerdesign einen großen Einfluss auf die Gleichmäßigkeit der Trocknung hat. Bei den einfachsten Trocknervarianten war die Verteilung auch bei optimal gepressten Ballen unzureichend, während komplexere Trockner eine gleichmäßigere Trocknung erzielten. Jedoch werden auch hier die Ergebnisse stark von der Verteilung der Dichte im Ballen beeinflusst, welche in der Praxis weiterhin nicht ideal ist. Abschließend wurde, um den Trocknungsfortschritt zu überwachen, eine Methodik getestet, bei der zur Messung des durchschnittlichen aktuellen Feuchtegehalts des Produktes psychrometrische Messungen und Messungen des Luftstroms in kurzen Abständen durchgeführt wurden. Die Menge des tatsächlich entfernten Wassers stimmte in den meisten Fällen gut mit der geschätzten Menge überein. Jedoch hängt der Erfolg dieser Methode stark von der Genauigkeit der Messfühler ab.

Simultaneous Drying and Separation of Composite Agricultural Material for Hay Processing

In composite agricultural materials such as grass, tee, medicinal plants; leaves and stems have a different drying time. By this behavior, after leaving the dryer, the stems may have greater moisture content than desired, while the leaves one minor, which can cause either the appearance of fungi or the collapse of the over-dried material. Taking into account that a lot of grass is dehydrated in forced air dryers, especially rotary drum dryers, this research was developed in order to establish conditions enabling to make a separation of the components during the drying process in order to provide a homogeneous product at the end. For this, a rotary dryer consisting of three concentric cylinders and a circular sieve aligned with the more internal cylinder was proposed; so that, once material enters into the dryer in the area of the inner cylinder, stems pass through sieve to the middle and then continue towards the external cylinder, while the leaves continue by the inner cylinder. For this project, a mixture of Ryegrass and White Clover was used. The characteristics of the components of a mixture were: Drying Rate in thin layer and in rotation, Bulk density, Projected Area, Terminal velocity, weight/Area Ratio, Flux through Rotary sieve. Three drying temperatures; 40°C, 60° C and 80° C, and three rotation speeds; 10 rpm, 20 rpm and 40 rpm were evaluated. It was found that the differences in drying time are the less at 80 °C when the dryer rotates at 40 rpm. Above this speed, the material adheres to the walls of the dryer or sieve and does not flow. According to the measurements of terminal velocity of stems and leaves of the components of the mixture, the speed of the air should be less than 1.5 m s-1 in the inner drum for the leaves and less than 4.5 m s-1 in middle and outer drums for stems, in such way that only the rotational movement of the dryer moves the material and achieves a greater residence time. In other hand, the best rotary sieve separation efficiencies were achieved when the material is dry, but the results are good in all the moisture contents. The best rotary speed of sieve is within the critical rotational speed, i.e. 20 rpm. However, the rotational speed of the dryer, including the sieve in line with the inner cylinder should be 10 rpm or less in order to achieve the greatest residence times of the material inside the dryer and the best agitation through the use of lifting flights. With a finite element analysis of a dryer prototype, using an air flow allowing speeds of air already stated, I was found that the best performance occurs when, through a cover, air enters the dryer front of the Middle cylinder and when the inner cylinder is formed in its entirety through a sieve. This way, air flows in almost equal amounts by both the middle and external cylinders, while part of the air in the Middle cylinder passes through the sieve towards the inner cylinder. With this, leaves do not adhere to the sieve and flow along drier, thanks to the rotating movement of the drums and the showering caused by the lifting flights. In these conditions, the differences in drying time are reduced to 60 minutes, but the residence time is higher for the stems than for leaves, therefore the components of the mixture of grass run out of the dryer with the same desired moisture content.

El Corán y la paz.

Después de los ataques del 11-s, este artículo pretende aclarar la raíz del problema entre el mundo musulmán y el occidental, la clave se encuentra en el Corán. Tras una introducción histórica sobre los orígenes del Islam, pasa a analizar el contenido, la estructura y varios versículos (o 'aliyas') del Corán (o 'Alcorán') que tratan sobre el determinismo, la incitación a la guerra, la discriminación de las mujeres, la salvación de los judíos y cristianos y la autorización de la hiperpoligamia.

Esplendores del Corán.

Título anterior de la publicación: Boletín de la Comisión Española de la UNESCO

Subsurface drip irrigation emitter spacing effects on soil water redistribution, corn yield and water productivity

Emitter spacings of 0.3 to 0.6 m are commonly used for subsurface drip irrigation (SDI) of corn on the deep, silt loam soils of the U.S. Great Plains. Subsurface drip irrigation emitter spacings of 0.3, 0.6, 0.9 and 1.2 m were examined for the resulting differences in soil water redistribution, corn grain yield, yield components, seasonal water use, and water productivity in a 4‐year field study (2005 through 2008) at the Kansas State University Northwest Research‐Extension Center, Colby, Kansas. The results indicate that there is increased preferential water movement along the dripline (parallel) as compared to perpendicular to the dripline and that this phenomenon partially compensates for wider emitter spacings in terms of soil water redistribution. Corn yield and water productivity (WP) were not significantly affected by the emitter spacing with application of a full irrigation regime

Introducing improved cultivars: Understanding farmers' seed drying and storage practices in central Ghana

Improved upland rice cultivars introduced in Volta Region, Ghana, have been perceived to store poorly compared to farmers' traditional cultivars. A survey was conducted in 2003 in the Hohoc district of this region, where a participatory Varietal Selection programme had started in 1997, to gain insight into fanners' seed production and storage practices that are likely to affect seed quality in storage. Farmers rated keeping quality (p < 0.001), tolerance to storage pests (p < 0.001), seed quality (p < 0.001) and establishment of their local cultivars Kawomo, Viono and Wuwulili as much better than the improved cultivar IDSA 85. Initial seed moisture content ranged from 12.8 to 18% and germination from 0 to 82%. There was a significant relationship between seed moisture content and duration of drying prior to storage (p < 0.001) and storage method (p = 0.015). Germination loss in storage was rapid at high moisture content and slow at low moisture content. Between 60 and 80% of seeds germinated after six Months storage at 12.8% moisture content. The viability equation predicted accurately germination of farmer-saved seed stored under ambient temperature in Ghana. Except for the japonica rice cultivar WAB 126-18-HB, the traditional cultivars Kawomo, Viono and Wuwulili survived better in storage than improved cultivars. There is a need to improve seed quality of improved cultivars if farmers are to benefit from their higher yields and grain quality and to improve storage practices.

Priming and re-drying improve the survival of mature seeds of Digitalis purpurea during storage

Most priming studies have been conducted on commercial seed lots of unspecified uniformity and maturity, and subsequent seed longevity has been reported to both increase and decrease. Here a seed lot of Digitalis purpurea L. with relatively uniform maturity and known history was used to analyse the effects of priming on seed longevity in air-dry storage. Seeds collected close to natural dispersal and dried at 15 % relative humidity (RH), 15 degrees C, were placed into experimental storage (60 % RH, 45 degrees C) for 14 or 28 d, primed for 48 h at 0, -1, -2, -5, -10 or -15 MPa, re-equilibrated (47 % RH, 20 degrees C) and then returned to storage. Further seed samples were primed for 2 or 48 h at -1 MPa and either dried at 15 % RH, 15 degrees C or immediately re-equilibrated for experimental storage. Finally, some seeds were given up to three cycles of experimental storage and priming (48 h at -1 MPa). Priming at -1 MPa had a variable effect on subsequent survival during experimental storage. The shortest lived seeds in the control population showed slightly increased life spans; the longer lived seeds showed reduced life spans. In contrast, seeds first stored for 14 or 28 d before priming had substantially increased life spans. The increase tended to be greatest in the shortest lived fraction of the seed population. Both the period of rehydration and the subsequent drying conditions had significant effects on longevity. Interrupting air-dry storage with additional cycles of priming also increased longevity. The extent of prior deterioration and the post-priming desiccation environment affect the benefits of priming to the subsequent survival of mature seeds. Rehydration-dehydration treatments may have potential as an adjunct or alternative to the regeneration of seed accessions maintained in gene banks for plant biodiversity conservation or plant breeding.

Effects of corn silage derived from a genetically modified variety containing two Transgenes on feed intake, milk production, and composition, and the absence of detectable Transgenic deoxyribonucleic acid in milk in holstein dairy cows

The objectives were to compare the chemical composition, nutritive value, feed intake, milk production and composition, and presence in milk of transgenic DNA and the encoded protein Cry1Ab when corn silages containing 2 transgenes (2GM: herbicide tolerance: mepsps and insect resistance: cry1Ab) were fed as part of a standard total mixed ration (TMR) compared with a near isogenic corn silage ( C) to 8 multiparous lactating Holstein dairy cows in a single reversal design study. Cows were fed a TMR ration ad libitum and milked twice daily. Diets contained [ dry matter (DM) basis] 45% corn silage, 10% alfalfa hay, and 45% concentrate (1.66 Mcal of net energy for lactation/kg of DM, 15.8% crude protein, 35% neutral detergent fiber, and 4.1% fat). Each period was 28-d long. During the last 4 d of each period, feed intake and milk production data were recorded and milk samples taken for compositional analysis, including the presence of transgenic DNA and Cry1Ab protein. There was no significant difference in the chemical composition between C and 2GM silages, and both were within the expected range (37.6% DM, 1.51 Mcal of net energy for lactation/kg, 8.6% crude protein, 40% neutral detergent fiber, 19.6% acid detergent fiber, pH 3.76, and 62% in vitro DM digestibility). Cows fed the 2GM silage produced milk with slightly higher protein (3.09 vs. 3.00%), lactose ( 4.83 vs. 4.72%) and solids-not-fat (8.60 vs. 8.40%) compared with C. However, the yield (kg/d) of milk (36.5), 3.5% fat-corrected milk (34.4), fat (1.151), protein (1.106), lactose (1.738), and solids-not-fat ( 3.094), somatic cell count (log(10): 2.11), change in body weight (+ 7.8 kg), and condition score (+ 0.09) were not affected by type of silage, indicating no overall production difference. All milk samples were negative for the presence of transgenic DNA from either trait or the Cry1Ab protein. Results indicate that the 2GM silage modified with 2 transgenes did not affect nutrient composition of the silages and had no effect on animal performance and milk composition. No transgenic DNA and Cry1Ab protein were detected in milk.

Effects of restricted water availability and increased temperature on the grain filling, drying and quality of winter wheat

Experiments in controlled environments examined the effects of the timing and severity of drought, and increased temperature, on grain development of Hereward winter wheat. Environmental effects on grain specific weight, protein content, Hagberg Falling Number, SDS-sedimentation volume, and sulphur content were also studied. Drought and increased temperature applied before the end of grain filling shortened the grain filling period and reduced grain yield, mean grain weight and specific weight. Grain filling was most severely affected by drought between days 1-14 after anthesis. Protein content was increased by stresses before the end of grain growth, because nitrogen harvest index was less severely affected than was dry matter harvest index. Hagberg Falling Number was increased to the greatest extent by stresses applied 15-28 days after anthesis. Treatment effects on grain sulphur content were similar to those on protein content, such that N:S ratio was not significantly affected by drought nor temperature stresses. The effects of restricted water on grain yield and quality were linearly related to soil moisture between 44 and about 73% field capacity (FC) from days 15-28. Drought stress (but not temperature stress) before the end of grain filling decreased SDS-sedimentation volume relative to drought applied later. (C) 2003 Elsevier Science Ltd. All rights reserved.

Potential cost and environmental impact of feeding high-oil corn to poultry in Brazil

The objective of the study was to evaluate the cost and environmental impact of replacing traditional corn, which is the main ingredient in poultry diets, with a high-oil corn (HOC) variety. Using linear programming, diets were formulated with either traditional corn or HOC. The results indicate that HOC-based diets cost up to $11.38/tonne less than traditional corn-based diets. Using HOC rather than traditional corn in diets has the potential to reduce the annual nitrogen excreted to the environment from broilers and broiler breeders in Brazil by 6.44 Mtonnes. In addition, there is the potential to reduce P excretion by 4.52 Mtonnes/yr, because the need to supplement diets with inorganic P sources, such as dicalcium phosphate, is much lower with HOC-based diets. We estimate that 28.5 Mtonnes of dicalcium phosphate can be saved annually using HOC in Brazilian poultry diets. The literature suggests that replacing traditional corn with HOC does not affect bird metabolism, while positive impacts on growth rate have been recorded. Therefore, substituting traditional corn with HOC has cost and environmental benefits for the Brazilian poultry industry without compromising productivity.

Drying method influences the development of germinability, dessication tolerance and subsequent longevity of immature seeds of sumauma (Ceiba pentandra (L.) Gaertn. [Bombacaceae])

The ability to germinate, tolerate desiccation and survive in air-dry storage was investigated during early seed development in planta and subsequent ex planta maturation of sumauma (Ceiba pentandra). Immature fruits were collected on three different dates (i.e. from about 5 days before until 7 days after mass maturity). Immature fresh seeds were not able to germinate. Fruits or seeds were subjected immediately after each collection to three different drying treatments with progressively slower rates of dessication: (i) seeds were extracted from the fruits and dried immediately; (ii) fruits were dried in a thin layer; (iii) fruits were dried in a tied polyethylene bag (with 10 holes of 1cm diameter). Drying was in a room maintained at 25 degrees C +/- 3 degrees C and 65%+/- 5% r.h. For treatment (i) the seeds were dried for 6 days in order to reduce moisture content to around 13% ( +/- 2%) moisture content. For treatments (ii) and (iii) the fruits were subjected to different periods of drying depending upon collection date. The results of these post-collection treatments showed generally that the more immature the seeds the slower the rate of drying that is required to improve ability to germinate, ability to tolerate desiccation and potential longevity, but at the third harvest, 7 days after mass maturity, the intermediate drying rate treatment was the most beneficial. Thus post fruit collection treatments can be modified depending upon the stage of seed development in order to provide good to high quality seeds of sumauma when collection has to be made at a site with difficult access at less than ideal times. The results are relevant to seed collection practices for both forestry and ex situ plant biodiversity conservation.

Near infrared reflectance spectroscopy (NIRS) to predict biological parameters of maize silage: effects of particle comminution, oven drying temperature and the presence of residual moisture

Maize silage nutritive quality is routinely determined by near infrared reflectance spectroscopy (NIRS). However, little is known about the impact of sample preparation on the accuracy of the calibration to predict biological traits. A sample population of 48 maize silages representing a wide range of physiological maturities was used in a study to determine the impact of different sample preparation procedures (i.e., drying regimes; the presence or absence of residual moisture; the degree of particle comminution) on resultant NIR prediction statistics. All silages were scanned using a total of 12 combinations of sample pre-treatments. Each sample preparation combination was subjected to three multivariate regression techniques to give a total of 36 predictions per biological trait. Increased sample preparations procedure, relative to scanning the unprocessed whole plant (WP) material, always resulted in a numerical minimisation of model statistics. However, the ability of each of the treatments to significantly minimise the model statistics differed. Particle comminution was the most important factor, oven-drying regime was intermediate, and residual moisture presence was the least important. Models to predict various biological parameters of maize silage will be improved if material is subjected to a high degree of particle comminution (i.e., having been passed through a 1 mm screen) and developed on plant material previously dried at 60 degrees C. The extra effort in terms of time and cost required to remove sample residual moisture cannot be justified. (c) 2005 Elsevier B.V. All rights reserved.