Kraft recovery boilers – Principles and practice

This book was created as postgraduate lecture notes for Lappeenranta University of Technology's special course of steam power plants. But as with anything ever written the ideas shown have nurtured for a long time. Parts of these chapters have appeared elsewhere as individual papers or work documents. One of the most helpful episodes have been presentations and discussions during Pohto Operator training seminars. Input from those sessions can be seen in chapter firing. You who run recovery boilers, I salute you. The purpose of this text is to give the reader an overview of recovery boiler operation. Most parts of the recovery boiler operation are common to boilers burning other fuels. The furnace operation differs significantly from operation of other boiler furnaces. Oxygen rich atmosphere is needed to burn fuel efficiently. But the main function of recovery boiler is to reduce spent cooking chemicals. Reduction reactions happen best in oxygen deficient atmosphere. This dual, conflicting nature of recovery furnace makes understanding it so challenging. To understand the processes happening in the recovery furnace one must try to understand the detailed processes that might occur and their limitations. Therefore chapters on materials, corrosion and fouling have been added.

Benefits of gas driven ground source heat pump systems

This thesis studies energy efficiencies and technical properties of gas driven ground source heat pumps and pump systems. The research focuses on two technologies: gas engine driven compressor heat pump and thermally driven gas absorption heat pump. System consist of a gas driven compressor or absorption ground source heat pump and a gas condensing boiler, which covers peak load. The reference system is a standard electrically powered compressor heat pump with electric heating elements for peak load. The systems are compared through primary energy ratios. Coefficient of performances of different heat pump technologies are also compared. At heat pump level, gas driven heat pumps are having lower coefficient of performances as compared with corresponding electric driven heat pump. However, gas heat pumps are competitive when primary energy ratios, where electricity production losses are counted in, are compared. Technically, gas heat pumps can potentially achieve a slightly higher temperatures with greater total energy efficiency as compared to the electric driven heat pump. The primary energy ratios of gas heat pump systems in relation to EHP-system improves when the share of peak load increases. Electric heat pump system's overall energy efficiency is heavily dependent on the electricity production efficiency. Economy as well as CO2-emissions were not examined in this thesis, which however, would be good topics for further study.

Meesauunin vaipan konepajavalmistus ja laaduntarkastus

Meesauuni on osa sulfaattisellutehdasta ja sen kemikaalikiertoa. Se on pyörivä kaltevaan tasoon asetettu rumpu-uuni, joka voi olla jopa 160 metriä pitkä ja halkaisijaltaan 5,5 metriä. Kalkki on kiertävä apukemikaali, jota käytetään soodakattilalta tulevan viherlipeän muuttamiseen valkolipeäksi. Meesauunin tehtävänä on kierrättää kalkki (CaO) uudelleen käytettäväksi kaustisoinnissa syntyneestä meesasta (CaCO3). Meesauunin vaipan konepajavalmistus on prosessina hyvin yksinkertainen, mutta toleranssivaatimukset ovat hyvin tiukat suhteutettuna meesauunin kokoon. Vaippalohkojen valmistus on siirtynyt halpatyövoiman maihin lähelle loppukäyttäjiä, joten vaatimukset piirustusten laadulle, valmistukselle, ohjeille ja tarkastamiselle ovat lisääntyneet. Uunin vaippa toimitetaan asennuspaikalle useassa lohkossa ja jokainen vaippalohko on tarkastettava ennen toimitusta. Virheellisten vaippalohkojen siirtyminen asennuspaikalle on estettävä. Työn tavoitteena oli parantaa meesauunin vaippalohkojen konepajavalmistuksen laaduntarkastusta. Tässä työssä tutkitaan mittausmenetelmiä vaippalohkojen geometrian mittaamiseen. Tärkeimmät uunin toiminnallisiin ominaisuuksiin vaikuttavat muototoleranssit vaippalohkoille ovat ympyrämäisyys ja keskiviivan suoruus. Virheet näissä toleransseissa aiheuttavat vaurioita uunin muurauksille ja liian suuria kuormituksia tuennoille. Vaippalohkot on mitattava pyöritysrullaston päällä ja konepajan olosuhteissa, mikä aiheuttaa omat haasteensa. Vaippalohkojen suuret massat ja dimensiot aiheuttavat vaippalohkoihin muodonmuutoksia. Muodonmuutokset täytyy olla hallinnassa, mikäli halutaan käyttää CMS-laitteistoja (Coordinate Measuring System). Meesauunin vaippalohkot ovat mitattavissa radiaalimittauksina tai käyttäen CMS-laitteistoja.

Kiertoleijupetikattilateknologia ja sen matemaattinen mallinnus energiantuotantoprosessissa

Työn teoreettisessa osuudessa tehdään katsaus kiertoleijupetiteknologian eri osa-alueisiin: leijupedin virtausdynamiikkaan, hiukkaserottimeen ja kiintoaineen palautusmekanismiin. Myös teknologian historiaa ja muita käyttötarkoituksia energiantuotannon ohella käydään läpi. Termodynamiikkaa sekä lämmönsiirron ja voimalaitosprosessien teoriaa käsitellään mallinnuksessa tarvittavilta osin. Mallinnusosiossa käydään läpi kiertoleijupetihöyrykattilan matemaattisen mallin tekoprosessia. Malli perustuu yleisesti saatavilla oleviin yhtälöihin ja korrelaatioihin. Mallintaminen koostuu höyrykattilan jakamisesta lämpöpintoihin ja niiden mitoittamisesta. Mallissa esitetään myös näkemys siitä, miten lämpö siirtyy savukaasuun ja miten petimateriaalin kierto tapahtuu tulipesässä.

Separation of lignin in Pulp Mill process and its effect on sodium sulphur balance

The aim of this thesis is to define effects of lignin separation process on Pulp mill chemical balance especially on sodium/sulphur-balance. The objective is to develop a simulation model with WinGEMS Process Simulator and use that model to simulate the chemical balances and process changes. The literature part explains what lignin is and how kraft pulp is produced. It also introduces to the methods that can be used to extract lignin from black liquor stream and how those methods affect the pulping process. In experimental part seven different cases are simulated with the created simulation model. The simulations are based on selected reference mill that produces 500 000 tons of bleached air-dried (90 %) pulp per year. The simulations include the chemical balance calculation and the estimated production increase. Based on the simulations the heat load of the recovery boiler can be reduced and the pulp production increased when lignin is extracted. The simulations showed that decreasing the waste acid stream intake from the chlorine dioxide plant is an effective method to control the sulphidity level when about 10 % of lignin is extracted. With higher lignin removal rates the in-mill sulphuric acid production has been discovered to be a better alternative to the sulphidity control.

Biomassakattilan simulointi

Tässä diplomityössä mallinnetaan Apros-simulointiohjelmistolla kylläistä höyryä tuottava KPA Uniconin toimittama Biograte-kattilalaitos. Työ on rajattu käsittelemään vesihöyrypiiri syöttövesisäiliöstä prosessiin lähtevään höyryyn saakka. Savukaasupuoli on mallinnettu polttoaineen ja palamisilman syötöstä savupiippuun asti, mutta savukaasujen puhdistus on jätetty pois simulaatiomallista. Työssä kerrotaan yleisesti biopolttoaineista, kattilalaitoksista ja tulipesäratkaisuista. Simuloitava kattilalaitos ja sen säätöjärjestelmä käydään läpi yksityiskohtaisemmin. Simuloinnista ja sen mahdollisuuksista kerrotaan yleisesti, jonka jälkeen esitellään tehty simulaatiomalli. Simulointituloksia verrataan kattilan mitoitusarvoihin ja tärkeimpien prosessisuureiden muutoksia tutkitaan kuormanmuutostilanteissa. Lopuksi tuloksista tehdään yhteenveto ja esitellään jatkotoimenpidesuunnitelmat. Simuloitu kattilalaitos tuottaa kylläistä höyryä halutun määrän oikeassa paineessa ja lämpötilassa. Kattilan prosessisuureet vastaavat melko hyvin mitoitusarvoja ja simulaatiomalli toimii vakaasti myös kuormanmuutostilanteissa. Suurimmat kompromissit ja yksinkertaistukset on tehty tulipesän ja polttoaineensyötön mallinnuksessa. Näitä osa-alueita kehittämällä simulaation tarkkuutta olisi mahdollista parantaa entisestään. Jatkossa simulointimallia on tarkoitus kehittää laajentamalla se kattamaan myös laitoksen sekundääripuoli kokonaisuudessaan. Tulosten perusteella simulaatiota voidaan pitää onnistuneena mallina Biograte-kattilalaitoksesta.

Puu- ja turvetuhkan hyötykäyttökelpoisuuteen vaikuttavat tekijät pienillä polttolaitoksilla

Energiantuotannossa syntyvä tuhka voi olla laadultaan hyvin vaihtelevaa ja laadunvaihtelulle on haastavaa löytää yksiselitteistä syy-seuraussuhdetta. Ympäristönsuojelulainsäädäntö ja taloudelliset intressit ohjaavat tuhkantuottajia etsimään tuhkalle sopivia hyötykäyttökohteita, ja sen vuoksi tuhkan laatuun ja hyötykäyttökelpoisuuteen vaikuttavia tekijöitä on tarpeen selvittää. Tässä diplomityössä on tutkittu pienissä, alle 50 MW:n polttolaitoksissa syntyvää tuhkaa. Tavoitteena oli selvittää, kuinka tuhkan hyötykäyttökelpoisuuteen voidaan vaikuttaa. Tutkimuksen kohteena oli polttoainekoostumuksen, poltto-olosuhteiden ja tuhkan jälkikäsittelyn vaikutus tuhkassa olevien haitta-aineiden pitoisuuksiin ja liukoisuuksin. Työhön sisältyi myös aiemmin tehtyjen tuhka-analyysien tarkastelu sekä tuhkakokeet kahdella kohderyhmään kuuluvalla laitoksella. Työssä todettiin lentotuhkan haitta-ainepitoisuuksien ja -liukoisuuksien olevan keskimäärin korkeampia kuin pohjatuhkan vastaavien, ja että tyypillisesti arinakattilan tuhkien haitta-aineet ylittävät useammin hyötykäyttökelpoisuuden raja-arvoja kuin kuplaleijupetikattilan tuhkien. Lisäksi havaittiin metsätähdehaketuhkan kelpaavan useammin hyötykäyttöön kuin rankahaketuhkan.

Voimalaitosten kattilaputkien sisäpuolisten kerrostumien paksuuden mittaaminen ultraäänimenetelmällä

Höyryvoimalaitoksen käyttöönotossa muodostuu kattilaputkien sisäpinnoille niitä korroosiolta suojaava ohut metallioksidikerros. Tämän kerroksen päälle kasvaa kattilan käytön aikana haitallista kerrostumaa paikallisen korroosion tai kattilavedessä olevien epäpuhtauksien kerääntymisen tai kiteytymisen seurauksena. Kerrostuma haittaa lämmönsiirtoa tulipesästä putkiseinämän läpi kattilaveteen. Putkien lämpötilan nousu suunniteltua korkeammaksi kasvattaa putkivaurioiden ja sisäpuolisen korroosion riskiä. Tästä johtuen paksuksi kasvaneet kerrostumat pyritään poistamaan happokäsittelyllä eli peittauksella ennen vaurioiden syntyä. Perinteisesti kerrostumapaksuus on määritetty kattilasta irrotetuista näyteputkista mikroskoopilla. Työn tavoitteena oli tutkia uudenlaisen ultraäänimittauksen teoriaa ja selvittää sen toimivuus höyrystinputkien kerrostumapaksuusmittauksissa. Lisäksi tavoitteena oli tutkia voimalaitoksen höyrystimen sisäpuolisten kerrostumien muodostumista ja niiden vaikutuksia sekä kattilan peittaustarpeen arviointia. Höyrystimen kerrostumien kasvunopeuteen vaikuttavat eniten voimalaitostyyppi, käytetty vesikemia ja kattilaveteen kulkeutuvien epäpuhtauksien määrä. Kasvunopeus vaihtelee laitosten välillä suuresti ja eroaa myös tulipesän eri kohdissa. Kattilaveden epäpuhtauspitoisuus ja kerrostumapaksuus vaikuttavat molemmat korroosiovaurioiden todennäköisyyteen. Peittauspaksuuden ohjearvoissa tulisi huomioida kattilan käyttöpaine, kattilatyyppi ja riski kattilaveden laadun heikkenemiselle. Putkinäytteistä ja laitoksilla suoritettujen mittauksien perusteella uusi ultraäänitekniikka tuottaa luotettavia tuloksia tavanomaisten kerrostumien mittauksessa. Vain yhdellä laitoksella esiintyi irtonaisen sakan kaltaista kerrostumaa, jota mittaus ei kyennyt havaitsemaan. Mittaustulokset kerrostumista tulipesän eri osissa antavat hyvän perustan peittaustarpeen arviointiin.

Optimal Recycling Combination of Ash in South-East Finland

The present world energy production is heavily relying on the combustion of solid fuels like coals, peat, biomass, municipal solid waste, whereas the share of renewable fuels is anticipated to increase in the future to mitigate climate change. In Finland, peat and wood are widely used for energy production. In any case, the combustion of solid fuels results in generation of several types of thermal conversion residues, such as bottom ash, fly ash, and boiler slag. The predominant residue type is determined by the incineration technology applied, while its composition is primarily relevant to the composition of fuels combusted. An extensive research has been conducted on technical suitability of ash for multiple recycling methods. Most of attention was drawn to the recycling of the coal combustion residues, as coal is the primary solid fuel consumed globally. The recycling methods of coal residues include utilization in a cement industry, in concrete manufacturing, and mine backfilling, to name few. Biomass combustion residues were also studied to some extent with forest fertilization, road construction, and road stabilization being the predominant utilization options. Lastly, residues form municipal solid waste incineration attracted more attention recently following the growing number of waste incineration plants globally. The recycling methods of waste incineration residues are the most limited due to its hazardous nature and varying composition, and include, among others, landfill construction, road construction, mine backfilling. In the study, environmental and economic aspects of multiple recycling options of thermal conversion residues generated within a case-study area were studied. The case-study area was South-East Finland. The environmental analysis was performed using an internationally recognized methodology — life cycle assessment. Economic assessment was conducted applying a widely used methodology — cost-benefit analysis. Finally, the results of the analyses were combined to enable easier comparison of the recycling methods. The recycling methods included the use of ash in forest fertilization, road construction, road stabilization, and landfill construction. Ash landfilling was set as a baseline scenario. Quantitative data about the amounts of ash generated and its composition was obtained from companies, their environmental reports, technical reports and other previously published literature. Overall, the amount of ash in the case-study area was 101 700 t. However, the data about 58 400 t of fly ash and 35 100 t of bottom ash and boiler slag were included in the study due to lack of data about leaching of heavy metals in some cases. The recycling methods were modelled according to the scientific studies published previously. Overall, the results of the study indicated that ash utilization for fertilization and neutralization of 17 600 ha of forest was the most economically beneficial method, which resulted in the net present value increase by 58% compared to ash landfilling. Regarding the environmental impact, the use of ash in the construction of 11 km of roads was the most attractive method with decreased environmental impact of 13% compared to ash landfilling. The least preferred method was the use of ash for landfill construction since it only enabled 11% increase of net present value, while inducing additional 1% of negative impact on the environment. Therefore, a following recycling route was proposed in the study. Where possible and legally acceptable, recycle fly and bottom ash for forest fertilization, which has strictest requirements out of all studied methods. If the quality of fly ash is not suitable for forest fertilization, then it should be utilized, first, in paved road construction, second, in road stabilization. Bottom ash not suitable for forest fertilization, as well as boiler slag, should be used in landfill construction. Landfilling should only be practiced when recycling by either of the methods is not possible due to legal requirements or there is not enough demand on the market. Current demand on ash and possible changes in the future were assessed in the study. Currently, the area of forest fertilized in the case-study are is only 451 ha, whereas about 17 600 ha of forest could be fertilized with ash generated in the region. Provided that the average forest fertilizing values in Finland are higher and the area treated with fellings is about 40 000 ha, the amount of ash utilized in forest fertilization could be increased. Regarding road construction, no new projects launched by the Center of Economic Development, Transport and the Environment in the case-study area were identified. A potential application can be found in the construction of private roads. However, no centralized data about such projects is available. The use of ash in stabilization of forest roads is not expected to increased in the future with a current downwards trend in the length of forest roads built. Finally, the use of ash in landfill construction is not a promising option due to the reducing number of landfills in operation in Finland.

Energy efficiency of glassmaking production

Master’s thesis Energy efficiency of glassmaking production gives description of glassmaking production and possible energy saving measures. Due to the high electricity and fuel prices the problem of rational energy utilization rises sharply. In addition the environmental issues also require a great attention. This work represented the feasible increasing of the furnace efficiency as the most productive activity. Thesis also provides a detail description of utilizing waste heat boiler. Also possible boiler characteristics are calculated and represented at the end of the thesis. As well as brief description of the feasibility of using this method of energy saving. The solution of this problem has a huge importance. Due to the increasing of energy costs and limits of raw materials, glassmaking industry should overcome on high efficiency operation mode. Especially, if such measures is making a significant contribution in the safety of environment.

Second Welland Canal - Book 1, Survey Map 11 - St. Catharines and Locks 3 and 4

Survey map of the Second Welland Canal created by the Welland Canal Company showing the Town of St. Catharines. Identified structures associated with the Canal include Lock 3 and its Lock House, Lock 4 and its Lock House, Hydraulic Race, and a floating tow path. The surveyors' measurements and notes can be seen in red and black ink and pencil. Local area landmarks are also identified and include streets and roads (ex. Geneva Street, Ontario Street, St. Paul Street, and Merritville Road), Lincoln Mills and its Store House, T. M. Merritt's Store House, Cooper Shop, L. Shickluna's Dry Dock, Peter McGill's Grist Mill, J. Flint's Saw Factory, T. Hosteter's Gristing Mill, J. Dougan Builder's shop or office, Norris and Nelson Mill, G. N. Oil Foundry and its Machine Shop and Boiler, a barrel shed, woolen factory, Estate of P. Nihen (or T. Nihan), Norris and Nelson's Wharf, the W. C. Office, and structures (possibly houses) or small properties belonging to T. Adams, and A. K. Boomer. Properties and property owners of note are: Concession 6 Lots 16, 17, and 18, Concession 7 Lots 16, 17, and 18, Alva Dittrick, James R. Benson, W. B. Robinson, and C. Phelps.

Management approaches in organic potato and tomato production

The presented thesis considered three different system approach topics to ensure yield and plant health in organically grown potatoes and tomatoes. The first topic describes interactions between late blight (Phytophthora infestans) incidence and soil nitrogen supply on yield in organic potato farming focussing in detail on the yield loss relationship of late blight based on results of several field trials. The interactive effects of soil N-supply, climatic conditions and late blight on the yield were studied in the presence and absence of copper fungicides from 2002-2004 for the potato cultivar Nicola. Under conditions of central Germany the use of copper significantly reduced late blight in almost all cases (15-30 %). However, the reductions in disease through copper application did not result in statistically significant yield increases (+0 – +10 %). Subsequently, only 30 % of the variation in yield could be attributed to disease reductions. A multiple regression model (R²Max), however, including disease reduction, growth duration and temperature sum from planting until 60 % disease severity was reached and soil mineral N contents 10 days after emergence could explain 75 % of the observed variations in yield. The second topic describes the effect of some selected organic fertilisers and biostimulant products on nitrogen-mineralization and efficiency, yield and diseases in organic potato and tomato trials. The organic fertilisers Biofeed Basis (BFB, plant derived, AgroBioProducts, Wageningen, Netherlands) and BioIlsa 12,5 Export (physically hydrolysed leather shavings, hair and skin of animals; ILSA, Arizignano, Italy) and two biostimulant products BioFeed Quality (BFQ, multi-compound seaweed extract, AgroBioProducts) and AUSMA (aqueous pine and spruce needle extract, A/S BIOLAT, Latvia), were tested. Both fertilisers supplied considerable amounts of nitrogen during the main uptake phases of the crops and reached yields as high or higher as compared to the control with horn meal fertilisation. The N-efficiency of the tested fertilisers in potatoes ranged from 90 to 159 kg yield*kg-1 N – input. Most effective with tomatoes were the combined treatments of fertiliser BFB and the biostimulants AUSMA and BFQ. Both biostimulants significantly increased the share of healthy fruit and/or the number of fruits. BFQ significantly increased potato yields (+6 %) in one out of two years and reduced R. solani-infestation in the potatoes. This suggests that the biostimulants had effects on plant metabolism and resistance properties. However, no effects of biostimulants on potato late blight could be observed in the fields. The third topic focused on the effect of suppressive composts and seed tuber health on the saprophytic pathogen Rhizoctonia solani in organic potato systems. In the present study 5t ha-1 DM of a yard and bio-waste (60/40) compost produced in a 5 month composting process and a 15 month old 100 % yard waste compost were used to assess the effects on potato infection with R. solani when applying composts within the limits allowed. Across the differences in initial seed tuber infestation and 12 cultivars 5t DM ha-1 of high quality composts, applied in the seed tuber area, reduced the infestation of harvested potatoes with black scurf, tuber malformations and dry core tubers by 20 to 84 %, 20 to 49 % and 38 to 54 %, respectively, while marketable yields were increased by 5 to 25 % due to lower rates of wastes after sorting (marketable yield is gross yield minus malformed tubers, tubers with dry core, tubers with black scurf > 15% infested skin). The rate of initial black scurf infection of the seed tubers also affected tuber number, health and quality significantly. Compared to healthy seed tubers initial black scurf sclerotia infestation of 2-5 and >10 % of tuber surface led in untreated plots to a decrease in marketable yields by 14-19 and 44-66 %, a increase of black scurf severity by 8-40 and 34-86 % and also increased the amount of malformed and dry core tubers by 32-57 and 109-214 %.

Co-fuelling of peat with meat and bone meal in a pilot scale bubbling bed reactor

Co-combustion performance trials of Meat and Bone Meal (MBM) and peat were conducted using a bubbling fluidized bed (BFB) reactor. In the combustion performance trials the effects of the co-combustion of MBM and peat on flue gas emissions, bed fluidization, ash agglomeration tendency in the bed and the composition and quality of the ash were studied. MBM was mixed with peat at 6 levels between 15% and 100%. Emissions were predominantly below regulatory limits. CO concentrations in the flue gas only exceeded the 100 mg/m3 limit upon combustion of pure MBM. SO2 emissions were found to be over the limit of 50 mg/m3, while in all trials NOx emissions were below the limit of 300 mg/m3. The HCl content of the flue gases was found to vary near the limit of 30 mg/m3. VOCs however were within their limits. The problem of bed agglomeration was avoided when the bed temperature was about 850 °C and only 20% MBM was co-combusted. This study indicates that a pilot scale BFB reactor can, under optimum conditions, be operated within emission limits when MBM is used as a co-fuel with peat. This can provide a basis for further scale-up development work in industrial scale BFB applications

UK Zero Carbon Homes 2016 - Exemplary Development

In October 2008 UK government announced very ambitious commitment to reduce greenhouse gas emissions of at least 34% by 2020 and by 80% by 2050 against a 1990 baseline. Consequently the government declares that new homes should be built to high environmental standards which means that from 2016 new homes will have to be built to a Zero Carbon standard. The paper sets out to present UK zero carbon residential development achieving the highest, Level 6 of Code for Sustainable Homes standard. Comprehensive information is provided about various environmental aspects of the housing development. Special attention is given to energy efficiency features of the houses and low carbon district heating solution which include biomass boiler, heat pumps, solar collectors and photovoltaic panels. The paper presents also challenges which designers and builders had to face delivering houses of the future.

Reduction of greenhouse gas emissions from UK hotels in 2030

The feasibility of halving greenhousegasemissions from hotels by 2030 has been studied as part of the Carbon Vision Buildings Programme. The aim of that programme was to study ways of reducing emissions from the existing stock because it will be responsible for the majority of building emissions over the next few decades. The work was carried out using detailed computer simulation using the ESP-r tool. Two hotels were studied, one older and converted and the other newer and purpose-built, with the aim of representing the most common UKhotel types. The effects were studied of interventions expected to be available in 2030 including fabric improvements, HVAC changes, lighting and appliance improvements and renewable energy generation. The main finding was that it is technically feasible to reduce emissions by 50% without compromising guest comfort. Ranking of the interventions was problematical for several reasons including interdependence and the impacts on boiler sizing of large reductions in the heating load