In vitro osteogenesis induced by cells derived from sites submitted to sinus grafting with anorganic bovine bone

Objectives: This study evaluated key parameters of the in vitro osteogenesis induced by osteoblastic cells obtained from sites submitted to sinus grafting with anorganic bovine bone (ABB) in comparison with cells derived from bone sites of the same patients. Materials and methods: In three patients, the augmentation of maxillary sinus was carried out using ABB (Bio-Oss (R)). After at least 6 months, during the surgical intervention for titanium implants placement, biopsies were taken from these areas using trephine burs (grafted group). Bone fragments, of the same patients, from sites that had not received graft were also obtained with trephine burs and used as a control group. Osteoblastic cells were obtained from grafted and control groups by enzymatic digestion and cultured under standard osteogenic condition until subconfluence. First passaged cells were cultured in 24-well culture plates. Cell adhesion was evaluated at 24 h. For proliferation and viability assay, cells were cultured for 1, 3, 7, and 10 days. Total protein content and alkaline phosphatase (ALP) activity were measured at 3, 7, 10, 14, 17, and 21 days. Cultures were stained with Alizarin red S at 21 days, for detection of mineralized matrix. Data were compared by Student`s t-test. Results: Cell adhesion and viability were not affected by cell source (P>0.05). Total protein content was greater (P<0.05) for grafted group. Cell proliferation, ALP activity, and bone-like nodule formation were all greater (P<0.05) for the control group. Conclusions: Taken together, these results indicate that the in vivo long-term contact of cells with ABB downregulates the expression of osteoblast phenotype and consequently the in vitro osteogenesis.

Seeding Osteoblastic Cells into a Macroporous Biodegradable CaP/PLGA Scaffold by a Centrifugal Force

This study aims to construct a hybrid biomaterial by seeding osteoblastic cells into a CaP/PLGA scaffold by a centrifugal force. Constructs are evaluated with respect to potential application in bone tissue engineering. Cells adher, spread, and form a layer of tissue lining the scaffold and are capable of migrating, proliferating, and producing mineralized matrix. We have demonstrated that the centrifugal force is highly efficient for constructing a hybrid biomaterial, which acts similarly to bone explants in a cell culture environment. In this way, these constructs could mimic an autogenous bone graft in clinical circumstances. Such a strategy may be useful for bone tissue engineering.

Media stress intensity analysis for vertical stirred mills

Experimental work has been carried out to investigate the effect of major operating variables on milling efficiency of calcium carbonate in laboratory and pilot size Tower and Sala Agitated (SAM) mills. The results suggest that the stirrer speed, media size and slurry density affect the specific energy consumption required to achieve the given product size. Media stress intensity analysis developed for high-speed horizontal mills was modified to include the effect of gravitational force in the vertical stirred mills such as the Tower and SAM units. The results suggest that this approach can be successfully applied for both mill types. For a given specific energy input, an optimum stress intensity range existed, for which the finest product was achieved. Finer product and therefore higher milling efficiency was obtained with SAM in the range of operating conditions tested. (C) 2001 Elsevier Science Ltd. All rights reserved.

Model-based procedure for scale-up of wet, overflow ball mills - Part II: Worked example

A new ball mill scale-up procedure is developed which uses laboratory data to predict the performance of MI-scale ball mill circuits. This procedure contains two laboratory tests. These laboratory tests give the data for the determination of the parameters of a ball mill model. A set of scale-up criteria then scales-up these parameters. The procedure uses the scaled-up parameters to simulate the steady state performance of the full-scale mill circuit. At the end of the simulation, the scale-up procedure gives the size distribution, the volumetric flowrate and the mass flowrate of all the streams in the circuit, and the mill power draw. A worked example shows how the new ball mill scale-up procedure is executed. This worked example uses laboratory data to predict the performance of a full-scale re-grind mill circuit. This circuit consists of a ball mill in closed circuit with hydrocyclones. The MI-scale ball mill has a diameter (inside liners) of 1.85m. The scale-up procedure shows that the full-scale circuit produces a product (hydrocyclone overflow) that has an 80% passing size of 80 mum. The circuit has a recirculating load of 173%. The calculated power draw of the full-scale mill is 92kW (C) 2001 Elsevier Science Ltd. All rights reserved.

Developments in the understanding of South African style SAG mills

The South African style SAG (RoM) mills operate in a window that is almost exclusive from the operation of the Australian and North American mills that have been used for the development of SAG mill models. Combining good quality, test data from the RoM mills is extending and improving these models, and assisting in a practical manner in improving our understanding of SAG/AG milling. Data from high mill loads, both in absolute filling and ball loading, have been used to extend and improve the JK SAG mill model. This improved understanding has been successfully applied to increasing the throughput of a mill by 8%. Data is presented on relationships between power and load for high mill loading. Slurry pooling is common in closed-circuit RoM mills, and the detrimental effect of this has been dramatically demonstrated at ALCOA with a mill throughput increase of over 20%. Techniques for calculating the effects of slurry pooling have been developed and a new pulp lifter system designed to give optimal slurry discharge. The influence of mill speed in shifting the product size distribution has also been measured. (C) 2001 Elsevier Science Ltd. All rights reserved.

Investigation of the effects of chrome ball charge on slurry rheology and milling performance

Ten surveys of the ball milling circuit at the Mt Isa Mines (MIM) Copper Concentrator were conducted aiming to identify any changes in slurry theology caused by the use of chrome balls charge, and the associated effect on grinding performance. Slurry theology was measured using an on-line viscometer. The data were mass balanced and analysed with statistical tools. Comparison of the rheogram demonstrated that slurry density and fines content affected slurry rheology significantly, while the effect of the chrome ball charge being negligible. Statistical analysis showed the effects of mill throughput and cyclone efficiency on the Grinding Index (a term describing the overall breakage). There was no difference in the Grinding Index between using the chrome ball charge and the ordinary steel ball charge. (C) 2002 Elsevier Science Ltd. All rights reserved.

'Vigilant Hospitality': The Online Imperative and Teaching Cultural Studies

Information technology (IT) sees information as a fluid, to be stored, regulated and exchanged. This is a profoundly economic model, whose dreams are those of the marketplace – and now, university managers. But no teacher, of course, holds that teaching can be reduced to the movement of information from one point to another. Teaching is never quite absorbed into the models of IT. Where they meet, we do not have the utopia of the virtual classroom, at last freed from the strictures of timetables and the face-to-face; we have, rather, the grinding of two radically irreducible models. This has nothing to do with Luddism; on the contrary, it is the value and necessity of IT for us at present, as teachers. At a time when the tertiary sector’s massive investment in IT is motivated in part by its own dream of the teacherless classroom, one of the pressing tasks for us may be simply to argue as rigorously as we can the structural necessity of our own position as teachers, without nostalgia or humanist sentimentality.

Practical and economic advantages of choice feeding systems for laying poultry

Poultry can be managed under different feeding systems, depending on the husbandry skills and the feed available. These systems include the following: (1) a complete dry feed offered as a mash ad libitum; (2) the same feed offered as pellets or crumbles ad libitum; (3) a complete feed with added whole grain; (4) a complete wet feed given once or twice a day; (5) a complete feed offered on a restricted basis; (6) choice feeding. Of all these, an interesting alternative to offering complete diets is choice feeding which can be applied on both a small or large commercial scale. Under choice feeding or free-choice feeding birds are usually offered a choice between three types of feedstuffs: (a) an energy source (e.g. maize, rice bran, sorghum or wheat); (b) a protein source (e.g. soyabean meal, meat meal, fish meal or coconut meal) plus vitamins and minerals and (c), in the case of laying hens, calcium in granular form (i.e. oyster-shell grit). This system differs from the modern commercial practice of offering a complete diet comprising energy and protein sources, ground and mixed together. Under the complete diet system, birds are mainly only able to exercise their appetite for energy. When the environmental temperature varies, the birds either over- or under-consume protein and calcium. The basic principle behind practising choice feeding with laying hens is that individual hens are able to select from the various feed ingredients on offer and compose their own diet, according to their actual needs and production capacity. A choice-feeding system is of particular importance to small poultry producers in developing countries, such as Indonesia, because it can substantially reduce the cost of feed. The system is flexible and can be constructed in such a way that the various needs of a flock of different breeds, including village chickens, under different climates can be met. The system also offers a more effective way to use home-produced grain, such as maize, and by-products, such as rice bran, in developing countries. Because oyster-shell grit is readily available in developing countries at lower cost than limestone, the use of cheaper oyster-shell grit can further benefit small-holders in these countries. These benefits apart, simpler equipment suffices when designing and building a feed mixer on the farm, and transport costs are lower. If whole (unground) grain is used, the intake of which is accompanied by increased efficiency of feed utilisation, the costs of grinding, mixing and many of the handling procedures associated with mash and pellet preparation are eliminated. The choice feedstuffs can all be offered in the current feed distribution systems, either by mixing the ingredients first or by using a bulk bin divided into three compartments.

Discrete element modelling of the influence of lifters on power draw of tumbling mills

Crushing and grinding are the most energy intensive part of the mineral recovery process. A major part of rock size reduction occurs in tumbling mills. Empirical models for the power draw of tumbling mills do not consider the effect of lifters. Discrete element modelling was used to investigate the effect of lifter condition on the power draw of tumbling mill. Results obtained with PFC3D code show that lifter condition will have a significant influence on the power draw and on the mode of energy consumption in the mill. Relatively high lifters will consume less power than low lifters, under otherwise identical conditions. The fraction of the power that will be consumed as friction will increase as the height of the lifters decreases. This will result in less power being used for high intensity comminution caused by the impacts. The fraction of the power that will be used to overcome frictional resistance is determined by the material's coefficient of friction. Based on the modelled results, it appears that the effective coefficient of friction for in situ mill is close to 0.1. (C) 2003 Elsevier Science Ltd. All rights reserved.

The JK three-product cyclone - performance and potential applications

In spite of their wide application in comminution circuits, hydrocyclones have at least one significant disadvantage in that their operation inherently tends to return the fine denser liberated minerals to the grinding mill. This results in unnecessary overgrinding which adds to the milling cost and can adversely affect the efficiency of downstream processes. In an attempt to solve this problem, a three-product cyclone has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to generate a second overflow in which the fine dense liberated minerals can be selectively concentrated for further treatment. In this paper, the design and operation of the three-product cyclone are described. The influence of the length of the second vortex finder on the performance of a 150-mm unit treating a mixture of magnetite and silica is investigated. Conventional cyclone tests were also conducted under similar conditions. Using the operational performance data of the three-product and conventional cyclones, it is shown that by optimising the length of the second vortex finder, the amount of fine dense mineral particles that reports to the three-product cyclone underflow can be reduced. In addition, the three-product cyclone can be used to generate middlings stream that may be more suitable for flash flotation than the conventional cyclone underflow, or alternatively, could be classified with a microscreen to separate the valuables from the gangue. At the same time, a fines stream having similar properties to those of the conventional overflow can be obtained. Hence, if the middlings stream was used as feed for flash flotation or microscreening, the fines stream could be used in lieu of the conventional overflow without compromising the feed requirements for the conventional flotation circuit. Some of the other potential applications of the new cyclone are described. (C) 2003 Elsevier Science B.V. All rights reserved.

Inv(f)erno da Universidade de Verão

Despesa em educação é investimento constitucional: art.s 75º e 76º da Constituição. Como referiu o director da Revista Ensino Superior, nº 53, pp. 4-5, ex-presidente do Sindicato Nacional do Ensino Superior, Professor da Faculdade de Economia da Universidade de Coimbra, Doutor Paulo Peixoto, o ensino superior tornou-se em grande parte uma “máquina de triturar intelectuais”. A tentativa de impor uma mentalidade única pode provocar a destruição da génese da própria universalidade. § Spending on education is constitutional investment: Articles 75 and 76 of the Constitution. As the director of the Journal of Higher Education, # 53, pp. 4-5, former president of the National Union of Higher Education, Professor of Economics, University of Coimbra, Dr. Paulo Peixoto, higher education has become largely an 'intellectual grinding machine. "The attempt to impose a single mindset may cause the destruction of the very universality genesis.

Produção de bioetanol a partir de um resíduo orgânico proveniente da central de compostagem da LIPOR

Mestrado em Engenharia Química

Simulação e programação offline de robôs industriais afectos a tarefas de lixagem

Este trabalho teve o intuito de testar a viabilidade da programação offline para tarefas de lixamento na empresa Grohe Portugal. Para tal era necessário perceber o que é a programação offline e para isso foi efectuada uma pesquisa referente a essa temática, onde ficou evidente que a programação offline é em tudo semelhante à programação online, tendo apenas como principal diferença o facto de não usar o robô propriamente dito durante o desenvolvimento do programa. Devido à ausência do robô, a programação offline exige que se conheça detalhadamente a célula de trabalho, bem como todas as entradas e saídas associadas à célula, sendo que o conhecimento das entradas e saídas pode ser contornada carregando um backup do robô ou carregando os módulos de sistema. No entanto os fabricantes habitualmente não fornecem informação detalhada sobre as células de trabalho, o que dificulta o processo de implementação da unidade no modelo 3D para a programação offline. Após este estudo inicial, foi efectuado um estudo das características inerentes a cada uma das células existentes, com o objectivo de se obter uma melhor percepção de toda a envolvente relacionada com as tarefas de lixamento. Ao longo desse estudo efectuaram-se vários testes para validar os diversos programas desenvolvidos, bem como para testar a modelação 3D efectuada. O projecto propriamente dito consistiu no desenvolvimento de programas offline de forma a minimizar o impacto (em especial o tempo de paragem) da programação de novos produtos. Todo o trabalho de programação era até então feito utilizando o robô, o que implicava tempos de paragem que podiam ser superiores a três dias. Com o desenvolvimento dos programas em modo offline conseguiu-se reduzir esse tempo de paragem dos robôs para pouco mais de um turno (8h), existindo apenas a necessidade de efectuar algumas afinações e correcções nos movimentos de entrada, saída e movimentações entre rotinas e unidades, uma vez que estes movimentos são essenciais ao bom acabamento da peça e convém que seja suaves. Para a realização e conclusão deste projecto foram superadas diversas etapas, sendo que as mais relevantes foram: - A correcta modelação 3D da célula, tendo em conta todo o cenário envolvente, para evitar colisões do robô com a célula; - A adaptação da programação offline para uma linguagem mais usual aos afinadores, ou seja, efectuar a programação com targets inline e criar diferentes rotinas para cada uma das partes da peça, facilitando assim a afinação; - A habituação à programação recorrendo apenas ao uso de módulos para transferir os programas para a célula, bem como a utilização de entradas, saídas e algumas rotinas e funcionalidades já existentes.

Experimental study on polyester based concretes filled with glass fibre reinforced plastic recyclates – a contribution to composite materials sustainability

The development and applications of thermoset polymeric composites, namely fibre reinforced plastics (FRP), have shifted in the last decades more and more into the mass market [1]. Despite of all advantages associated to FRP based products, the increasing production and consume also lead to an increasing amount of FRP wastes, either end-of-lifecycle products, or scrap and by-products generated by the manufacturing process itself. Whereas thermoplastic FRPs can be easily recycled, by remelting and remoulding, recyclability of thermosetting FRPs constitutes a more difficult task due to cross-linked nature of resin matrix. To date, most of the thermoset based FRP waste is being incinerated or landfilled, leading to negative environmental impacts and supplementary added costs to FRP producers and suppliers. This actual framework is putting increasing pressure on the industry to address the options available for FRP waste management, being an important driver for applied research undertaken cost efficient recycling methods. [1-2]. In spite of this, research on recycling solutions for thermoset composites is still at an elementary stage. Thermal and/or chemical recycling processes, with partial fibre recovering, have been investigated mostly for carbon fibre reinforced plastics (CFRP) due to inherent value of carbon fibre reinforcement; whereas for glass fibre reinforced plastics (GFRP), mechanical recycling, by means of milling and grinding processes, has been considered a more viable recycling method [1-2]. Though, at the moment, few solutions in the reuse of mechanically-recycled GFRP composites into valueadded products are being explored. Aiming filling this gap, in this study, a new waste management solution for thermoset GFRP based products was assessed. The mechanical recycling approach, with reduction of GFRP waste to powdered and fibrous materials was applied, and the potential added value of obtained recyclates was experimentally investigated as raw material for polyester based mortars. The use of a cementless concrete as host material for GFRP recyclates, instead of a conventional Portland cement based concrete, presents an important asset in avoiding the eventual incompatibility problems arisen from alkalis silica reaction between glass fibres and cementious binder matrix. Additionally, due to hermetic nature of resin binder, polymer based concretes present greater ability for incorporating recycled waste products [3]. Under this scope, different GFRP waste admixed polymer mortar (PM) formulations were analyzed varying the size grading and content of GFRP powder and fibre mix waste. Added value of potential recycling solution was assessed by means of flexural and compressive loading capacities of modified mortars with regard to waste-free polymer mortars.

Desenvolvimento de programação offline e de novos processos robotizados de lixamento

Atualmente a vantagem competitiva de uma empresa passa pela sua rápida adaptação às variações de procura do mercado, sendo necessário garantir elevados níveis de produtividade e, simultaneamente, grande flexibilidade, indispensável ao fabrico de pequenos lotes. A necessidade de ajuste do processo e a diminuição da média de vida do produto levam a paragens cada vez mais frequentes da célula de fabrico para programação e afinação, com consequentes perdas de produtividade. De forma a dar resposta a estes problemas, neste trabalho é testada a viabilidade da utilização da programação e simulação offline de tarefas de lixamento na Grohe Portugal, complementando a solução com o desenvolvimento de um novo método de afinação do programa, permitindo uma adaptação às flutuações do processo produtivo. Para isso foi necessário analisar o estado da arte dos robôs industriais na área de acabamento superficial e respetivos métodos de programação. Em seguida, após um trabalho prévio rigoroso de preparação e modelação da célula de trabalho, é possível fazer a programação offline das várias rotinas e trajetórias complexas que compõem um ciclo de lixamento de um produto, contribuindo para o aumento da qualidade do produto final sem comprometer os níveis de produtividade. Nesta dissertação são descritos e detalhados alguns dos procedimentos fulcrais no sucesso da aplicação deste método de programação. Por último é feita uma nova abordagem ao método de ajuste ponto-a-ponto convencional, desenvolvendo-se para isso um sistema de ajuste automático do programa, dotando o robô da capacidade de se adaptar às variações do processo, assegurando a consistência do mesmo. Foram realizados testes em pequena escala, extrapolando-se os resultados para a aplicação deste novo método no processo produtivo da Grohe Portugal, como forma de complemento ao método convencional de ajuste ponto-a-ponto do programa, reduzindo o tempo de paragem da célula de trabalho.