Monomer conversion of composite dental resins photoactivated by a halogen lamp and a LED: a FT-Raman spectroscopy study

Eighteen circular blocks of resins cured either by a LED or a halogen lamp (20, 40 and 60 s), had their top (T) and bottom (B) surfaces studied using a FT-Raman spectrometer. Systematic changes in the intensity of the methacrylate C=C stretching mode at 1638 cm-1 as a function of exposure duration were observed. The calculated degree of conversion (DC) ranged from 45.0% (B) to 52.0% (T) and from 49.0% (B) to 55.0% (T) for the LED and halogen lamp, respectively. LED and halogen light produced similar DC values with 40 and 60 s of irradiation.

Computational and Experimental Investigation of the Grooved Roll in Paper Machine Environment

In the paper machine, it is not a desired feature for the boundary layer flows in the fabric and the roll surfaces to travel into the closing nips, creating overpressure. In this thesis, the aerodynamic behavior of the grooved roll and smooth rolls is compared in order to understand the nip flow phenomena, which is the main reason why vacuum and grooved roll constructions are designed. A common method to remove the boundary layer flow from the closing nip is to use the vacuum roll construction. The downside of the use of vacuum rolls is high operational costs due to pressure losses in the vacuum roll shell. The deep grooved roll has the same goal, to create a pressure difference over the paper web and keep the paper attached to the roll or fabric surface in the drying pocket of the paper machine. A literature review revealed that the aerodynamic functionality of the grooved roll is not very well known. In this thesis, the aerodynamic functionality of the grooved roll in interaction with a permeable or impermeable wall is studied by varying the groove properties. Computational fluid dynamics simulations are utilized as the research tool. The simulations have been performed with commercial fluid dynamics software, ANSYS Fluent. Simulation results made with 3- and 2-dimensional fluid dynamics models are compared to laboratory scale measurements. The measurements have been made with a grooved roll simulator designed for the research. The variables in the comparison are the paper or fabric wrap angle, surface velocities, groove geometry and wall permeability. Present-day computational and modeling resources limit grooved roll fluid dynamics simulations in the paper machine scale. Based on the analysis of the aerodynamic functionality of the grooved roll, a grooved roll simulation tool is proposed. The smooth roll simulations show that the closing nip pressure does not depend on the length of boundary layer development. The surface velocity increase affects the pressure distribution in the closing and opening nips. The 3D grooved roll model reveals the aerodynamic functionality of the grooved roll. With the optimal groove size it is possible to avoid closing nip overpressure and keep the web attached to the fabric surface in the area of the wrap angle. The groove flow friction and minor losses play a different role when the wrap angle is changed. The proposed 2D grooved roll simulation tool is able to replicate the grooved aerodynamic behavior with reasonable accuracy. A small wrap angle predicts the pressure distribution correctly with the chosen approach for calculating the groove friction losses. With a large wrap angle, the groove friction loss shows too large pressure gradients, and the way of calculating the air flow friction losses in the groove has to be reconsidered. The aerodynamic functionality of the grooved roll is based on minor and viscous losses in the closing and opening nips as well as in the grooves. The proposed 2D grooved roll model is a simplification in order to reduce computational and modeling efforts. The simulation tool makes it possible to simulate complex paper machine constructions in the paper machine scale. In order to use the grooved roll as a replacement for the vacuum roll, the grooved roll properties have to be considered on the basis of the web handling application.

Molecular and pathogenic variability of Drechslera isolates from oats

Severe epidemics of leaf blotch and black leaf spot of oat (Avena sativa) caused by Drechslera avenae and Drechslera sp., respectively, are frequently observed in the State of Paraná, Brazil. Although some morphological differences between the isolates causing two different symptoms were noticed, the genetic relationship between them was not clear. Twenty-four isolates of D. avenae and Drechslera sp, collected between 1996-98, were assessed for the genetic variability by molecular and pathogenic analyses. The amplification products using primer pair ITS4/ITS5 showed a fragment length of approximately 600 bp for all the isolates except for one black spot isolate, where the fragment length was approximately 550 bp. Restriction enzymes Hinf I and Taq I, that cut in the ITS region, produced similar restriction patterns for all the isolates, whereas four others produced variable restriction patterns. RAPD analysis also showed distinctive patterns for some isolates. No clear difference between the black spot and the leaf blotch isolates was observed either by the molecular or by the pathogenicity analysis. Nonetheless, the rDNA analysis suggests that Drechslera probably comprises at least three distinct taxa. The results indicate that the difference observed between the isolates originating from two types of symptoms is due to intra-specific variants of D. avenae.

Natural colonization of leaves of 'Pêra' sweet orange and related varieties by Guignardia citricarpa

The purpose of this research was to evaluate the differences in the colonization and production of structures in the leaves of 'Pêra' sweet orange (Citrus sinensis) clones and related varieties by Guignardia citricarpa. The natural colonization and the production of reproductive structures in the leaves and in vitro of ten 'Pêra' sweet orange was quantified in the following clones: Bianchi, Dibbern C.V., EEL, IAC 2000, Olímpia 15161, Premunizada 1212, Premunizada 1743/82, R. Gullo 1569/244, R. Gullo 1570/246 and Vimusa; and in five related varieties: Redonda C.N, Ovale 968, Ovale San Lio 969, Lamb Summer and Corsa Tardia. The quantification of the colonization density of G. citricarpa in the leaves was obtained through isolation. Incidence and colonization density (cm²) were calculated for each clone. The production of reproductive structures was accomplished through the moistening and drying process of the leaves. The incidence (percentage of affected leaves) and the leaf surface percentage occupied by the reproductive fungus structures were quantified. The in vitro production of reproductive structures was accomplished in water-agar medium. The number of immature and total reproductive fungus structures (cm²), and the percentage of picnidia with liberation of spores were quantified. Significant differences were not observed among clones related to the colonization of the leaves. But there were differences in the induction experiments, i.e., in the leaf surface percentage occupied by the reproductive fungus structures and the in vitro production of reprodutive fungus structures.

In vitro effect of substrate, temperature and photoperiod on Phakopsora pachyrhizi urediniospore germination and germ tube growth

In vitro experiments were conducted to assess the effects of substrate, temperature and time of exposure to temperature and photoperiod on P. pachyrhizi uredospore germination and germ tube growth. The following substrates were tested: water-agar and soybean leaf extract-agar at different leaf concentrations (0.5, 1.0, 2.0 and 4.0 g of leaves and 15g agar/L water), temperatures (10, 15, 20, 25, 30, and 35oC) and times of exposure (1, 2, 3, 4, 5, 6, 7, and 8 hours) to temperature and 12 different photoperiods. The highest germination and germ tube length was found for the soybean leaf extract agar. Maximum P. pachyrhizi uredospore germination was obtained at 21.8 and 22.3°C, and maximum germ tube growth at 21.4 and 22.1°C. The maximum uredospore germination was found at 6.4 hours exposure, while the maximum germ tube length was obtained at 7.7 h exposure. Regarding photoperiod, the maximum spore germination and the maximum uredospore germ tube length were found in the dark. Neither spore germination nor uredospore germ tube growth was completely inhibited by the exposure to continuous light.

Quantification of incubation, latent and infection periods of Phakopsora pachyrhizi in soybean, according to chronological time and degree-days

ABSTRACT In experiments conducted in a growth chamber, the chronological time and the accumulated degree-days were determined for the duration of incubation, latent and infectious periods of Phakopsora pachyrhizi cultivars BRSGO 7560 and BRS 246 RR. Detached soybean leaflets were placed in gerbox-type acrylic boxes and inoculated with 20 x 103 uredospores/mL. The study was conducted at 12-h photoperiod and temperatures of 10ºC, 15ºC, 22ºC, 25ºC and 30°C for 30 days. Lesions and uredia/cm2were evaluated and the number of uredia per lesion was quantified after the beginning of sporulation. The sporulation potential was also quantified for cultivars BRSGO 7560 and BRS 246 RR. The steps of the infection process can be quantified based on both the chronological time and the accumulated heat. The cultivar BRSGO 7560 produced 4,012.8 spores/cm2 and BRS 246 RR, 7,348.4 uredospores/cm2. The largest number of uredia was produced at 25ºC in both cultivars; however, BRS 246 RR presented 372.7 uredia/cm2 and BRSGO 7560, 231.6 uredia/cm2. At 10ºC and 30°C, leaf infection did not occur in both cultivars.

Establishment of Xaraés and Marandu grasses under levels of soil compaction

In Cerrado soils under grazing, changes occur in physical attributes, such as increased density, decreasing on the size of water stable aggregates, and macroporosity reduction. Thus, the aim of this study was to study the effect of compaction on the establishment of two forages. It was adopted a completely randomized design with three replications, in 2 x 4 factorial design, and two forages (Xaraés grass and Marandu grass), and four levels of compaction (soil densities of 1.0, 1.2, 1.4, and 1.6 Mg m-3). The following variables were evaluated 48 days after sowing: tiller population, plant height, dry matter production of shoots and components, leaf and stem, as well as the root dry mass. The stem dry mass decreased with soil density in a similar manner for both forages. It was observed that the leaf dry mass and shoots dry mass of Xaraés grass remained constant in the levels of soil compaction, not adjusting to any regression model. The establishment of Xaraés grass has not been negatively affected by compaction, which may be suitable for situations where there may be layers that restrict the growth of different forages.

Yield and quality of elephant grass biomass produced in the cerrados region for bioenergy

The objective of this study was to evaluate the performance of two genotypes of elephant grass, fertilized with and without N, for biomass production for energy use under the edaphoclimatic conditions of the Cerrado. The genotypes Roxo and Paraíso, grown in a field experiment in a Latosol in the Cerrado region were evaluated for biomass yield, nitrogen accumulation, C:N and stem:leaf ratios, fibre, ash and P and K contents and calorific value. The accumulated dry biomass ranged from 30 to 42 Mg ha-1 and showed no response to nitrogen fertilization with the lowest biomass obtained by the genotype Paraíso and the highest by Roxo. The total N accumulation followed the same pattern as for dry matter, ranging from 347 to 539 kg N ha-1. C:N and stem:leaf ratio of the biomass produced did not vary with treatments. The fibre contents were higher in genotype Paraíso and the highest levels of ash in the genotype Roxo. The K content in the biomass was higher in genotype Roxo and P did not vary between genotypes. The calorific value averaged 18 MJ kg-1 of dry matter and did not vary with the levels of N in leaves and stems of the plant. Both genotypes, independent of N fertilization, produced over 30 Mg ha-1 of biomass under Cerrado conditions.

Glyphosate translocation in hairy fleabane (Conyza bonariensis) biotypes

The objective of this work was to evaluate the translocation of glyphosate in C. bonariensis plants resistant and susceptible to that herbicide. The 14C-glyphosate was mixed with commercial gyhphosate (800 g ha-1) and applied on the center of the adaxial face of a third node leaf, using a micro syringe, and adding 10 µL of a solution with specific activity of 1,400 Bq, 45 days after plant emergence. The concentration of the glyphosate translocated in the plant was evaluated at time intervals of 6, 12, 36 and 72 hours after being applied on the application leaf, stem, roots and leaves. Ten hours after treatment application, the distribution of the product in the application leaf, divided into base, center and apex, was also evaluated by measuring the radiation emitted by 14C-glyphosate in a liquid scintillation spectrometer. Greater glyphosate retention was observed in the resistant biotype leaf, approximately 90% of the total absorbed up to 72 hours. In the susceptible biotype, this value was close to 70% in the same period. Susceptible biotype leaves, stem and roots showed greater concentration of glyphosate, indicating greater translocation efficiency in this biotype. In the resistant biotype, the herbicide accumulated in greater quantity at the apex and center of the application leaf, while in the susceptible biotype greater accumulation was observed at the base and center leaf. Thus, it can be stated that the resistance mechanism is related to the differential translocation of this herbicide in the biotypes.

Corn yield response to weed and fall armyworm controls

The interference imposed the by weeds on corn decreases practically all vegetative characteristics. As consequence, the green ear and grain yield are also reduced. Losses due to the fall armyworm (Spodoptera frugiperda) attack can reduce corn grain yield up to 34%. In general, weed and insect control issues are addressed separately in research papers. Nevertheless, interaction between weeds and insects may exist. This study aimed to evaluate green ear and corn grain yield response to weed and fall armyworm control. A completely randomized block design with split-plots and five replicates was adopted. Corn cultivar AG 1051 was grown under weedy conditions or with control by hand hoeings performed at 20 and 40 days after planting. Fall armyworm control (applied to subplots) was performed with sprays of water (control), deltamethrin (5g active ingredient ha-1); neem oil, at 0.5% (diluted in water), and neem leaf extract at 5%. Each product was sprayed three times, at seven-day intervals, starting at the 7th day after planting, using 150 L ha-1 of the tank solution. Dry mass of the above-ground part, internode diameter, leaf length, leaf width, leaf area, green ear yield and grain yield of corn were reduced due to the lack of weed control. Fall armyworm control in the weeded plots did not influence green ear yield and grain yield, except green mass of marketable, husked ears, which was reduced when the caterpillar was not controlled. Without weed control, neem extracts and deltamethrin sprays provided highest yields of number and total weight of green ears with husks, number and weight of marketable ears with husks and number of marketable ears without husks. The best results for husked ear mass and for grain yield were obtained with neem extract and deltamethrin, respectively.

Management of Bidens pilosa and Commelina benghalensis in organic corn cultivation under no-tillage

Mowing is one of the most important methods used to control weeds in organic farming, under the no-tillage system. This study aimed to evaluate the effects of three weed management techniques on weed development, using the weeds Bidens pilosa and Commelina benghalensis, in competition with organic corn {mowing at the three-leaf stage (14 days after corn emergence - DACE), mowing at the three- and six-leaf stage (14 and 25 DACE), and no mowing. Single cultivation with no mowing was also evaluated for these weeds. Mowings performed at 14 and 25 DACE prevented the production of B. pilosa seeds, ensuring efficient control of this species. However, the use of this technique was shown to be inefficient in the control of C. benghalensis.

Improving diquat efficacy on grasses by adding adjuvants to the spray solution before use

The effect of five adjuvants (non-ionic surfactant, paraffinic oil, vegetable oil, mixture of fatty acids methyl esters plus surfactant blend, and organosilicone) on diquat efficacy was assessed on poverty brome, sterile oat, and Italian ryegrass in field and pot experiments. All tank mixtures with diquat increased diquat efficacy from 50-54% to 77-98% as for fresh weight reduction, indicating significant enhancement of diquat efficacy on grasses. The increased efficacy was most likely attributed to better droplet retention and diffusion on the leaf surfaces. When combined with non-ionic surfactant, diquat showed slightly more rapid control of grass weeds (i.e. symptoms were visible within a few hours after application).

Biomechanical and histological evaluation of hydrogel implants in articular cartilage

We evaluated the mechanical behavior of the repaired surfaces of defective articular cartilage in the intercondylar region of the rat femur after a hydrogel graft implant. The results were compared to those for the adjacent normal articular cartilage and for control surfaces where the defects remained empty. Hydrogel synthesized by blending poly(2-hydroxyethyl methacrylate) and poly(methyl methacrylate-co-acrylic acid) was implanted in male Wistar rats. The animals were divided into five groups with postoperative follow-up periods of 3, 5, 8, 12 and 16 weeks. Indentation tests were performed on the neoformed surfaces in the knee joint (with or without a hydrogel implant) and on adjacent articular cartilage in order to assess the mechanical properties of the newly formed surface. Kruskal-Wallis analysis indicated that the mechanical behavior of the neoformed surfaces was significantly different from that of normal cartilage. Histological analysis of the repaired defects showed that the hydrogel implant filled the defect with no signs of inflammation as it was well anchored to the surrounding tissues, resulting in a newly formed articular surface. In the case of empty control defects, osseous tissue grew inside the defects and fibrous tissue formed on the articular surface of the defects. The repaired surface of the hydrogel implant was more compliant than normal articular cartilage throughout the 16 weeks following the operation, whereas the fibrous tissue that formed postoperatively over the empty defect was stiffer than normal articular cartilage after 5 weeks. This stiffness started to decrease 16 weeks after the operation, probably due to tissue degeneration. Thus, from the biomechanical and histological point of view, the hydrogel implant improved the articular surface repair.

Measuring higher order optical aberrations of the human eye: techniques and applications

In the present paper we discuss the development of "wave-front", an instrument for determining the lower and higher optical aberrations of the human eye. We also discuss the advantages that such instrumentation and techniques might bring to the ophthalmology professional of the 21st century. By shining a small light spot on the retina of subjects and observing the light that is reflected back from within the eye, we are able to quantitatively determine the amount of lower order aberrations (astigmatism, myopia, hyperopia) and higher order aberrations (coma, spherical aberration, etc.). We have measured artificial eyes with calibrated ametropia ranging from +5 to -5 D, with and without 2 D astigmatism with axis at 45º and 90º. We used a device known as the Hartmann-Shack (HS) sensor, originally developed for measuring the optical aberrations of optical instruments and general refracting surfaces in astronomical telescopes. The HS sensor sends information to a computer software for decomposition of wave-front aberrations into a set of Zernike polynomials. These polynomials have special mathematical properties and are more suitable in this case than the traditional Seidel polynomials. We have demonstrated that this technique is more precise than conventional autorefraction, with a root mean square error (RMSE) of less than 0.1 µm for a 4-mm diameter pupil. In terms of dioptric power this represents an RMSE error of less than 0.04 D and 5º for the axis. This precision is sufficient for customized corneal ablations, among other applications.

Inotropic effect of Citrus sinensis (L.) Osbeck leaf extracts on the guinea pig atrium

The objective of the present investigation was to determine the contractile effect of crude and acetone leaf extracts of Citrus sinensis (L.) Osb. on mammalian myocardium. Crude leaf extracts have been used in folk medicine to treat neurological disorders. Some flavonoids isolated from this plant presented a positive inotropic effect on myocardium. This motivated us to test the extracts on the atria of guinea pigs of both sexes (300-500 g) and surprisingly we observed inotropic depression instead of an increase in force. The maximum effect of the crude extract was 79.4 ± 8.1% of the control force amplitude (N = 5 hearts, 10 trials, 27 ± 0.1ºC, stimulus: 2 Hz, 400 V, 0.5 ms). The EC50 for crude, ethanol, acetic, aqueous, and acetone extracts was 300, 300, 600, 1000, and 140 µg/ml, respectively, with a Hill constant of 1.8, 2.0, 2.5, 2.0, and 1.4, respectively. Blockade of cholinergic, beta-adrenergic, or opioid membrane receptors with 1.5 µM atropine sulfate, 1 µM propranolol, and 10 µM naloxone, respectively, did not change the effect of the crude extract. The acetone extract abolished the Bowditch positive staircase phenomenon (N = 5 hearts, 10 trials, 27 ± 0.1ºC), suggesting a possible reduction of the calcium inward current, and also promoted the so-called Woodworth phenomenon. The effect was concentration-dependent and indicated the existence of another inhibitory contractile mechanism such as the simultaneous activation of some of the membrane potassium channels reducing the myocardial action potential duration and further decreasing the cellular calcium entry.