Numerical and Experimental Analysis of Balanced and Unbalanced Adhesive Single-Lap Joints between Aluminium Adherends

The single-lap joint is the most commonly used, although it endures significant bending due to the non-collinear load path, which negatively affects its load bearing capabilities. The use of material or geometric changes is widely documented in the literature to reduce this handicap, acting by reduction of peel and shear peak stresses or alterations of the failure mechanism emerging from local modifications. In this work, the effect of using different thickness adherends on the tensile strength of single-lap joints, bonded with a ductile and brittle adhesive, was numerically and experimentally evaluated. The joints were tested under tension for different combinations of adherend thickness. The effect of the adherends thickness mismatch on the stress distributions was also investigated by Finite Elements (FE), which explained the experimental results and the strength prediction of the joints. The numerical study was made by FE and Cohesive Zone Modelling (CZM), which allowed characterizing the entire fracture process. For this purpose, a FE analysis was performed in ABAQUS® considering geometric non-linearities. In the end, a detailed comparative evaluation of unbalanced joints, commonly used in engineering applications, is presented to give an understanding on how modifications in the bonded structures thickness can influence the joint performance.

Visible range plasmonic effect produced by aluminium nanoparticles embedded in amorphous silicon

We present results, obtained by means of an analytic study and a numerical simulation, about the resonant condition necessary to produce a Localized Surface Plasmonic Resonance (LSPR) effect at the surface of metal nanospheres embedded in an amorphous silicon matrix. The study is based on a Lorentz dispersive model for a-Si:H permittivity and a Drude model for the metals. Considering the absorption spectra of a-Si:H, the best choice for the metal nanoparticles appears to be aluminium, indium or magnesium. No difference has been observed when considering a-SiC:H. Finite-difference time-domain (FDTD) simulation of an Al nanosphere embedded into an amorphous silicon matrix shows an increased scattering radius and the presence of LSPR induced by the metal/semiconductor interaction under green light (560 nm) illumination. Further results include the effect of the nanoparticles shape (nano-ellipsoids) in controlling the wavelength suitable to produce LSPR. It has been shown that is possible to produce LSPR in the red part of the visible spectrum (the most critical for a-Si:H solar cells applications in terms of light absorption enhancement) with aluminium nano-ellipsoids. As an additional results we may conclude that the double Lorentz-Lorenz model for the optical functions of a-Si:H is numerically stable in 3D simulations and can be used safely in the FDTD algorithm. A further simulation study is directed to determine an optimal spatial distribution of Al nanoparticles, with variable shapes, capable to enhance light absorption in the red part of the visible spectrum, exploiting light trapping and plasmonic effects. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Strength improvement of adhesively-bonded scarf repairs in aluminium structures with external reinforcements

Adhesively bonded techniques are an attractive option to repair aluminium structures, compared to more traditional methods. Actually, as a result of the improvement in the mechanical characteristics of adhesives, adhesive bonding has progressively replaced the traditional joining methods. There are several bonded repair configurations, as single-strap, double-strap and scarf. Compared with strap repairs, scarf repairs have the advantages of a higher efficiency and the absence of aerodynamic disturbance. The higher efficiency is caused by the elimination of the significant joint eccentricities of strap repairs. Moreover, stress distributions along the bond length are more uniform, due to tapering of the scarf edges. The main disadvantages of this technique are the difficult machining of the surfaces, associated costs and requirement of specialised labour. This work reports on an experimental and numerical study of the tensile behaviour of two-dimensional (2D) scarf repairs of aluminium structures bonded with the ductile epoxy adhesive Araldite® 2015. The numerical analysis, by Finite Elements (FE), was performed in Abaqus® and used cohesive zone models (CZM) for the simulation of damage onset and growth in the adhesive layer, thus enabling the strength prediction of the repairs. A parametric study was performed on the scarf angle (α) and different configurations of external reinforcement (applied on one or two sides of the repair, and also different reinforcement lengths). The obtained results allowed the establishment of design guidelines for repairing, showing that the use of external reinforcements enables increasing α for equal strength recovery, which makes the repair procedure easier. The numerical technique was accurate in predicting the repairs’ strength, enabling its use for design and optimisation purposes.

Development and implementation of strategies for the incorporation of reinforcing elements in aluminium alloys by solid state processing

Dissertação para obtenção do Grau de Mestre em Engenharia Mecânica

Strength and damage analysis of composite-aluminium adhesively-bonded single-lap joints

With the need to find an alternative way to mechanical and welding joints, and at the same time to overcome some limitations linked to these traditional techniques, adhesive bonds can be used. Adhesive bonding is a permanent joining process that uses an adhesive to bond the components of a structure. Composite materials reinforced with fibres are becoming increasingly popular in many applications as a result of a number of competitive advantages. In the manufacture of composite structures, although the fabrication techniques reduce to the minimum by means of advanced manufacturing techniques, the use of connections is still required due to the typical size limitations and design, technological and logistical aspects. Moreover, it is known that in many high performance structures, unions between composite materials with other light metals such as aluminium are required, for purposes of structural optimization. This work deals with the experimental and numerical study of single lap joints (SLJ), bonded with a brittle (Nagase Chemtex Denatite XNRH6823) and a ductile adhesive (Nagase Chemtex Denatite XNR6852). These are applied to hybrid joints between aluminium (AL6082-T651) and carbon fibre reinforced plastic (CFRP; Texipreg HS 160 RM) adherends in joints with different overlap lengths (LO) under a tensile loading. The Finite Element (FE) Method is used to perform detailed stress and damage analyses allowing to explain the joints’ behaviour and the use of cohesive zone models (CZM) enables predicting the joint strength and creating a simple and rapid design methodology. The use of numerical methods to simulate the behaviour of the joints can lead to savings of time and resources by optimizing the geometry and material parameters of the joints. The joints’ strength and failure modes were highly dependent on the adhesive, and this behaviour was successfully modelled numerically. Using a brittle adhesive resulted in a negligible maximum load (Pm) improvement with LO. The joints bonded with the ductile adhesive showed a nearly linear improvement of Pm with LO.

Friction surfacing of aluminium alloys

Dissertação para a obtenção do grau de Mestre em Engenharia Mecânica

Gas tungsten arc welding of NiTi shape memory alloy

Shape memory alloys are characterized by the ability of recovering their initial shape after being deformed and by superelasticity. Since the discovery of these alloys, a new field of interest emerged not only for the scientific community but also to many industries. However, these alloys present poor machinability which constitute a constrain in the design of complex components for new applications. Thus, the demand for joining techniques able to join these alloys without compromising their properties became of great importance to enlarge the complexity of existing applications. Literature shows that these alloys are joined mainly using laser welding. In the present study, similar NiTi butt joints, were produced using TIG welding. The welds were performed in 1.5 mm thick plates across the rolling direction. A special fixture and gas assist device was designed and manufactured. Also a robot arm was adapted to accommodate the welding torch to assure the repeatability of the welding parameters. Welds were successfully achieved without macroscopic defects, such as pores and distortions. Very superficial oxidation was seen on the top surface due to insufficient shielding gas flow on the weld face. The welded joints were mechanically tested and structurally characterized. Testing methods were used to evaluate macro and microstructure, as well as the phase transformation temperatures, the mechanical single and cyclic behaviour and the shape recovery ability. Differential Scanning Calorimetry (DSC), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), microhardness measurements were techniques also used to evaluate the welded joints. A depletion in Ni in the fusion zone was seen, as well as a shift in Ms temperature. For strain values of 4% the accumulated irrecoverable strain was of about 30% and increased with the strain imposed during cycling. Nevertheless, a complete recovery of initial shape was observed when testing the shape memory effect on a dedicated device that introduces a deformation of 6.7%. That is, the welding procedure does not remove the ability of the specimens to recover their initial shape.

Plasma nitriding of AA2011 alloy and surface characterization by NDT techniques

Al-Cu alloys are widely used in the aerospace and automotive industries due to their high specific strength in some tempered conditions. However, due to poor corrosion and wear resistance, they are often anodized and/or painted. Plasma nitriding has been proposed as an alternative, though the developments in this technique are still in a recent stage for Al alloys. Electrical characterization techniques are well implemented NDTs in the industry because of good accuracy associated with lower cost, compared to other methods. Some, like eddy currents and 4-point probe techniques, are often used in coating inspection. The objective of this study was to perform Al nitriding at low temperatures to minimize the tempering initial condition damage and to assess the feasibility of eddy currents technique as a method for evaluating surface properties. The work developed can be divided in two stages. The first one was the process tuning, done at the Shibaura Institute of Technology, in Tokyo; and the second was the electrical characterization done in Faculdade de Ciências e Tecnologia, UNL. Low temperature nitriding of AA2011 alloy specimens was successfully achieved. Electrical conductivity results show that lift-off measurements by eddy currents testing can be related to surface properties.

Mechanical, fatigue and wear properties of sintered Carbon Nanotube-based functionally graded materials

Tese de Doutoramento Engenharia Mecânica

The influence of nitrogen and oxygen additions on the thermal characteristics of aluminium-based thin films

The ternary aluminium oxynitride (AlNxOy) system offers the possibility to obtain a wide range of properties by tailoring the ratio between pure Al, AlNx and AlOy and therefore opening a significant number of possible applications. In this work the thermal behaviour of AlNxOy thin films was analysed by modulated infrared radiometry (MIRR), taking as reference the binary AlOy and AlNx systems. MIRR is a non-contact and non-destructive thermal wave measurement technique based on the excitation, propagation and detection of temperature oscillations of very small amplitudes. The intended change of the partial pressure of the reactive gas (N2 and/or O2) influenced the target condition and hence the deposition characteristics which, altogether, affected the composition and microstructure of the films. Based on the MIRR measurements and their qualitative and quantitative interpretation, some correlations between the thermal transport properties of the films and their chemical/physical properties have been found. Furthermore, the potential of such technique applied in this oxynitride system, which present a wide range of different physical responses, is also discussed. The experimental results obtained are consistent with those reported in previous works and show a high potential to fulfil the demands needed for the possible applications of the systems studied. They are clearly indicative of an adequate thermal response if this particular thin film system is aimed to be applied in small sensor devices or in electrodes for biosignal acquisition, such as those for electroencephalography or electromyography as it is the case of the main research area that is being developed in the group.

Efeito da adição de Zr no endurecimento de ligas Al-Sc

Dissertação de mestrado integrado em Engenharia de Materiais

Optimisation of a surface mount technology process using a SnAgCu lead-free alloy

The impending introduction of lead-free solder in the manufacture of electrical and electronic products has presented the electronics industry with many challenges. European manufacturers must transfer from a tin-lead process to a lead-free process by July 2006 as a result of the publication of two directives from the European Parliament. Tin-lead solders have been used for mechanical and electrical connections on printed circuit boards for over fifty years and considerable process knowledge has been accumulated. Extensive literature reviews were conducted on the topic and as a result it was found there are many implications to be considered with the introduction of lead-free solder. One particular question that requires answering is; can lead-free solder be used in existing manufacturing processes? The purpose of this research is to conduct a comparative study of a tin-lead solder and a lead-free solder in two key surface mount technology (SMT) processes. The two SMT processes in question were the stencil printing process and the reflow soldering process. Unreplicated fractional factorial experimental designs were used to carry out the studies. The quality of paste deposition in terms of height and volume were the characteristics of interest in the stencil printing process. The quality of solder joints produced in the reflow soldering experiment was assessed using x-ray and cross sectional analysis. This provided qualitative data that was then uniquely scored and weighted using a method developed during the research. Nested experimental design techniques were then used to analyse the resulting quantitative data. Predictive models were developed that allowed for the optimisation of both processes. Results from both experiments show that solder joints of comparable quality to those produced using tin-lead solder can be produced using lead-free solder in current SMT processes.

Impact of casting parameters and chemical composition on the solidification behaviour of Al-Si-Cu hypoeutectic alloy

Magdeburg, Univ., Fak. für Maschinenbau, Diss., 2010

Technologische Erfordernisse beim Aluminium-Dünnwand-Kokillengießen

Magdeburg, Univ., Fak. für Maschinenbau, Diss., 2010

Ecologie industrielle de l'aluminium, flux de matières et d'énergie : réalités et enjeux du recyclage

Dans les dernières années du 20ème siècle, l'aluminium a fait l'objet de beaucoup de communications outrancières et divergentes cautionnées par des scientifiques et des organismes faisant autorité. En 1986, la société PECHINEY le décrète perpétuel tel le mouvement « L'aluminium est éternel. Il est recyclable indéfiniment sans que ses propriétés soient altérées », ce qui nous avait alors irrité. Peu de temps après, en 1990, une communication tout aussi outrancière et irritante d'une grande organisation environnementale, le World Wild Fund, décrète que « le recyclage de l'aluminium est la pire menace pour l'environnement. Il doit être abandonné ». C'est ensuite à partir de la fin des années 1990, l'explosion des publications relatives au développement durable, le bien mal nommé. Au développement, synonyme de croissance obligatoire, nous préférons société ou organisation humaine et à durable, mauvaise traduction de l'anglais « sustainable », nous préférons supportable : idéalement, nous aurions souhaité parler de société durable, mais, pour être compris de tous, nous nous sommes limités à parler dorénavant de développement supportable. Pour l'essentiel, ces publications reconnaissent les très graves défauts de la métallurgie extractive de l'aluminium à partir du minerai et aussi les mérites extraordinaires du recyclage de l'aluminium puisqu'il représente moins de 10% de la consommation d'énergie de la métallurgie extractive à partir du minerai (on verra que c'est aussi moins de 10% de la pollution et du capital). C'est précisément sur le recyclage que se fondent les campagnes de promotion de l'emballage boisson, en Suisse en particulier. Cependant, les données concernant le recyclage de l'aluminium publiées par l'industrie de l'aluminium reflètent seulement en partie ces mérites. Dans les années 1970, les taux de croissance de la production recyclée sont devenus plus élevés que ceux de la production électrolytique. Par contre, les taux de recyclage, établis à indicateur identique, sont unanimement tous médiocres comparativement à d'autres matériaux tels le cuivre et le fer. Composante de l'industrie de l'aluminium, le recyclage bénéficie d'une image favorable auprès du grand public, démontrant le succès des campagnes de communication. A l'inverse, à l'intérieur de l'industrie de l'aluminium, c'est une image dévalorisée. Les opinions émises par tous les acteurs, commerçants, techniciens, dirigeants, encore recueillies pendant ce travail, sont les suivantes : métier de chiffonnier, métier misérable, métier peu technique mais très difficile (un recycleur 15 d'aluminium n'a-t-il pas dit que son métier était un métier d'homme alors que celui du recycleur de cuivre était un jeu d'enfant). A notre avis ces opinions appartiennent à un passé révolu qu'elles retraduisent cependant fidèlement car le recyclage est aujourd'hui reconnu comme une contribution majeure au développement supportable de l'aluminium. C'est bien pour cette raison que, en 2000, l'industrie de l'aluminium mondiale a décidé d'abandonner le qualificatif « secondaire » jusque là utilisé pour désigner le métal recyclé. C'est en raison de toutes ces données discordantes et parfois contradictoires qu'a débuté ce travail encouragé par de nombreuses personnalités. Notre engagement a été incontestablement facilité par notre connaissance des savoirs indispensables (métallurgie, économie, statistiques) et surtout notre expérience acquise au cours d'une vie professionnelle menée à l'échelle mondiale dans (recherche et développement, production), pour (recherche, développement, marketing, stratégie) et autour (marketing, stratégie de produits connexes, les ferro-alliages, et concurrents, le fer) de l'industrie de l'aluminium. Notre objectif est de faire la vérité sur le recyclage de l'aluminium, un matériau qui a très largement contribué à faire le 20ème siècle, grâce à une revue critique embrassant tous les aspects de cette activité méconnue ; ainsi il n'y a pas d'histoire du recyclage de l'aluminium alors qu'il est plus que centenaire. Plus qu'une simple compilation, cette revue critique a été conduite comme une enquête scientifique, technique, économique, historique, socio-écologique faisant ressortir les faits principaux ayant marqué l'évolution du recyclage de l'aluminium. Elle conclut sur l'état réel du recyclage, qui se révèle globalement satisfaisant avec ses forces et ses faiblesses, et au-delà du recyclage sur l'adéquation de l'aluminium au développement supportable, adéquation largement insuffisante. C'est pourquoi, elle suggère les thèmes d'études intéressant tous ceux scientifiques, techniciens, historiens, économistes, juristes concernés par une industrie très représentative de notre monde en devenir, un monde où la place de l'aluminium dépendra de son aptitude à satisfaire les critères du développement supportable. ABSTRACT Owing to recycling, the aluminium industry's global energetic and environmental prints are much lower than its ore extractive metallurgy's ones. Likewise, recycling will allow the complete use of the expected avalanche of old scraps, consequently to the dramatic explosion of aluminium consumption since the 50's. The recycling state is characterized by: i) raw materials split in two groups :one, the new scrap, internal and prompt, proportional to semi-finished and finished products quantities, exhibits a fairly good and regular quality. The other, the old scrap, proportional to the finished products arrivïng at their end-of--life, about 22 years later on an average, exhibits a variable quality depending on the collect mode. ii) a poor recycling rate, near by that of steel. The aluminium industry generates too much new internal scrap and doesn't collect all the availa~e old scrap. About 50% of it is not recycled (when steel is recycling about 70% of the old scrap flow). iii) recycling techniques, all based on melting, are well handled in spite of aluminium atiiníty to oxygen and the practical impossibility to purify aluminium from any impurity. Sorting and first collect are critical issues before melting. iv) products and markets of recycled aluminium :New scraps have still been recycled in the production lines from where there are coming (closed loop). Old scraps, mainly those mixed, have been first recycled in different production lines (open loop) :steel deoxidation products followed during the 30's, with the development of the foundry alloys, by foundry pieces of which the main market is the automotive industry. During the 80's, the commercial development of the beverage can in North America has permitted the first old scrap recycling closed loop which is developing. v) an economy with low and erratic margins because the electrolytic aluminium quotation fixes scrap purchasing price and recycled aluminium selling price. vi) an industrial organisation historically based on the scrap group and the loop mode. New scrap is recycled either by the transformation industry itself or by the recycling industry, the remelter, old scrap by the refiner, the other component of the recycling industry. The big companies, the "majors" are often involved in the closed loop recycling and very seldom in the open loop one. To-day, aluminium industry's global energetic and environmental prints are too unbeara~ e and the sustainaЫe development criteria are not fully met. Critical issues for the aluminium industry are to better produce, to better consume and to better recycle in order to become a real sustainaЫe development industry. Specific issues to recycling are a very efficient recycling industry, a "sustainaЫe development" economy, a complete old scrap collect favouring the closed loop. Also, indirectly connected to the recycling, are a very efficient transformation industry generating much less new scrap and a finished products industry delivering only products fulfilling sustainaЫe development criteria.