Effect of coal-over-coal reburn on furnace temperature and heat flux distributions in 1 MW tangentially fired furnace

The furnace temperature and heat flux distributions of 1 MW tangentially fired furnace were studied during coal-over-coal reburn, and the influences of the position of reburn nozzle and reburn fuel fraction on furnace temperature and heat flux distributions were investigated. Compared with the baseline, the flue gas temperature is 70–90 C lower in primary combustion and 130–150 C higher at furnace exit, and the variations of the flue gas temperature distributions along furnace height are slower. The temperature distribution along the width of furnace wall decreases with the increase of the relative furnace height. In the primary combustion zone and the reburn zone, the temperature and heat flux distributions of furnace wall are much non-uniform and asymmetric along the width of furnace wall, those of furnace wall in the burnout zone are relatively uniform, and the temperature non-uniformity coefficients of the primary combustion zone, the reburn zone and the burnout zone are 0.290, 0.100 and 0.031, respectively.

A single-layer magnetic atom chip for trapping an array of Bose-Einstein condensate

We propose a simple single-layer magnetic microtrap configuration which can trap an array of magnetically-trapped Bose-Einstein condensate. The configuration consists of two series of parallel wires perpendicular to each other and all of the crossing points are cut off for maintaining the uniformity of the current. We analyse the trapping potential, the position of trapping centres and the uniformity of the array of the traps. The trapping depth and trapping frequency with different parameters are also calculated. Lastly, the effect of the cut-off crossing points, dissipate power, chip production are introduced concisely.

双掺杂LiNbO3晶体中光栅均匀性的优化研究

研究了非挥发全息记录中南于紫外光的强吸收而引起的光栅非均匀性，分析了这种非均匀性对光栅衍射效率的影响。结果显示，非均匀性致使光折变光栅的平均强度减弱，衍射效率降低。提出了采用两束等光强的敏化紫外光由晶体两侧入射的优化方案以改善光栅的均匀性，提高光栅的衍射效率。通过联立两中心带输运物质方程和双光束耦合波方程，进行了相应的理论模拟，并给出实验验证。结果表明双侧紫外光照射能够实现均匀性较好的光栅，是提高衍射效率的有效途径之一。

Ultrafast temporal pattern generation and recognition

Ultrafast temporal pattern generation and recognition with femtosecond laser technology is presented, analyzed, and experimentally implemented. Ultrafast temporal pattern generation and recognition are realized by taking advantage of two well-known techniques: the space-time conversion technique and the ultrafast pulse measurement technique. Here the temporal pattern for the designed multiple pulses, optimized with a preassumed Gaussian spectral distribution of an ultrashort pulse, is described. With the simulation of a Gaussian spectral distribution, we realize that the uniformity of the generated multiple ultrafast temporal pulses is relevant to the repeated number of modulation periods in the mask in the spectral plane. Moreover, the change of Gaussian spectral phases with the wavelengths in the modulated phase plate is considered. Experiments of ultrafast temporal pattern recognition by the frequency-resolved optical gating (FROG) characterization technique are also given. (C) 2004 Society of Photo-Optical Instrumentation Engineers.

Estimativa do erro de discretização analítico na solução de equações diferenciais utilizando o Método de Volumes Finitos

As análises de erros são conduzidas antes de qualquer projeto a ser desenvolvido. A necessidade do conhecimento do comportamento do erro numérico em malhas estruturadas e não-estruturadas surge com o aumento do uso destas malhas nos métodos de discretização. Desta forma, o objetivo deste trabalho foi criar uma metodologia para analisar os erros de discretização gerados através do truncamento na Série de Taylor, aplicados às equações de Poisson e de Advecção-Difusão estacionárias uni e bidimensionais, utilizando-se o Método de Volumes Finitos em malhas do tipo Voronoi. A escolha dessas equações se dá devido a sua grande utilização em testes de novos modelos matemáticos e função de interpolação. Foram usados os esquemas Central Difference Scheme (CDS) e Upwind Difference Scheme(UDS) nos termos advectivos. Verificou-se a influência do tipo de condição de contorno e a posição do ponto gerador do volume na solução numérica. Os resultados analíticos foram confrontados com resultados experimentais para dois tipos de malhas de Voronoi, uma malha cartesiana e outra triangular comprovando a influência da forma do volume finito na solução numérica obtida. Foi percebido no estudo que a discretização usando o esquema CDS tem erros menores do que a discretização usando o esquema UDS conforme literatura. Também se percebe a diferença nos erros em volumes vizinhos nas malhas triangulares o que faz com que não se tenha uma uniformidade nos gráficos dos erros estudados. Percebeu-se que as malhas cartesianas com nó no centróide do volume tem menor erro de discretização do que malhas triangulares. Mas o uso deste tipo de malha depende da geometria do problema estudado

Dynamic optical coupled system employing even-numbered Dammann gratings

Dammann gratings are well known for their ability to generate arrays of Lmiform-intensity beams from an incoming monochromatic beam. We apply the even-numbered Dammann grating to achieve dynamic optical coupled technology. A 1 x N dynamic optical coupled system is developed by employing two complementary even-numbered Dammann gratings. With this system we can achieve a beam splitter and combiner as a switch between them according to the relative shift between the gratings. Also, this system is a preferable approach in integral packaging. More importantly, this device has the potential to be applied to the splitting of a large array, e.g., 8 x 16 array and 64 x 64 array, which is difficult to be realized with conventional splitting methods. We experimentally demonstrated a 1 x 8 coupler at the wavelength of 1550 nm. Furthermore we analyze the effects of the alignment errors between gratings and the wavelength-dependent error on efficiency and uniformity. The experimental results and the influence of alignment error and wavelength-dependent error are analyzed in detail. (c) 2006 Optical Society of America.

基于达曼光栅的动态光耦合器

提出了一种基于达曼光栅的动态光耦合器,通过控制装置中达曼光栅位移参量,可实现入射光束的分束或合束以及两者之间的动态转换。适当选择达曼光栅类型可实现任意N×M的动态光耦合。实验中以1550 nm光波长为例,对1×8达曼动态光耦合器进行测量,测得其实现光开关功能时插入损耗为0.43 dB,实现光分束功能时均匀性达到0.03,单路插入损耗均值为10.5 dB。该实验装置易于调节、体积小、能耗低,且关键元件达曼光栅制作工艺成熟,易于批量化生产。特别是在实现中大规模光交换阵列时,该方案就具有更明显的优越性,有实用意

Microwave dynamics of quasiparticles and critical fields in superconducting films

The microwave response of the superconducting state in equilibrium and non-equilibrium configurations was examined experimentally and analytically. Thin film superconductors were mostly studied in order to explore spatial effects. The response parameter measured was the surface impedance.

For small microwave intensity the surface impedance at 10 GHz was measured for a variety of samples (mostly Sn) over a wide range of sample thickness and temperature. A detailed analysis based on the BCS theory was developed for calculating the surface impedance for general thickness and other experimental parameters. Experiment and theory agreed with each other to within the experimental accuracy. Thus it was established that the samples, thin films as well as bulk, were well characterised at low microwave powers (near equilibrium).

Thin films were perturbed by a small dc supercurrent and the effect on the superconducting order parameter and the quasiparticle response determined by measuring changes in the surface resistance (still at low microwave intensity and independent of it) due to the induced current. The use of fully superconducting resonators enabled the measurement of very small changes in the surface resistance (< 10^-9 Ω/sq.). These experiments yield information regarding the dynamics of the order parameter and quasiparticle systems. For all the films studied the results could be described at temperatures near T_c by the thermodynamic depression of the order parameter due to the static current leading to a quadratic increase of the surface resistance with current.

For the thinnest films the low temperature results were surprising in that the surface resistance decreased with increasing current. An explanation is proposed according to which this decrease occurs due to an additional high frequency quasiparticle current caused by the combined presence of both static and high frequency fields. For frequencies larger than the inverse of the quasiparticle relaxation time this additional current is out of phase (by π) with the microwave electric field and is observed as a decrease of surface resistance. Calculations agree quantitatively with experimental results. This is the first observation and explanation of this non-equilibrium quasiparticle effect.

For thicker films of Sn, the low temperature surface resistance was found to increase with applied static current. It is proposed that due to the spatial non-uniformity of the induced current distribution across the thicker films, the above purely temporal analysis of the local quasiparticle response needs to be generalised to include space and time non-equilibrium effects.

The nonlinear interaction of microwaves arid superconducting films was also examined in a third set of experiments. The surface impedance of thin films was measured as a function of the incident microwave magnetic field. The experiments exploit the ability to measure the absorbed microwave power and applied microwave magnetic field absolutely. It was found that the applied surface microwave field could not be raised above a certain threshold level at which the absorption increased abruptly. This critical field level represents a dynamic critical field and was found to be associated with the penetration of the app1ied field into the film at values well below the thermodynamic critical field for the configuration of a field applied to one side of the film. The penetration occurs despite the thermal stability of the film which was unequivocally demonstrated by experiment. A new mechanism for such penetration via the formation of a vortex-antivortex pair is proposed. The experimental results for the thinnest films agreed with the calculated values of this pair generation field. The observations of increased transmission at the critical field level and suppression of the process by a metallic ground plane further support the proposed model.

Effects of the frequency chirp on the fields of a chirped Gaussian pulse passing through a hard-edged aperture

Based on the Huygens-Fresnel diffraction integral and Fourier transform, propagation expression of a chirped Gaussian pulse passing through a hard-edged aperture is derived. Intensity distributions of the pulse with different frequency chirp in the near-field and far-field are analyzed in detail by numerical calculations. In the near-field, amplitudes of the intensity peaks generated by the modulation of the hard-edged aperture decrease with increasing the frequency chirp, which results in the improving of the beam uniformity. A physical explanation for the smoothing effect brought by increasing the frequency chirp is given. The smoothing effect is achieved not only in the pulse with Gaussian transverse profile but also in the pulse with Hermite-Gaussian transverse profile when the frequency chirp increases. (C) 2005 Elsevier B.V. All rights reserved.

Transverse intensity distributions of a broadband laser modulated by a hard-edged aperture

By means of the Huygens-Fresnel diffraction integral, the field representation of a laser beam modulated by a hard-edged aperture is derived. The near-field and far-field transverse intensity distributions of the beams with different bandwidths are analyzed by using the representation. The numerical calculation results indicate that the amplitudes and numbers of the intensity spikes decrease with increasing bandwidth, and beam smoothing is achieved when the bandwidth takes a certain value in the near field. In the far field, the radius of the transverse intensity distribution decreases as the bandwidth increases, and the physical explanation of this fact is also given. (c) 2005 Optical Society of America.

谱色散均匀化的计算研究

利用光传输理论对ICF驱动器中使用的光谱色散平滑(SSD)技术作了理论分析，并结合典型的随机相位板(RPP)技术，用计算机模拟了使用光谱色散平滑技术前后激光靶面辐照不均匀性的变化及其技术中不同带宽和调制频率下激光靶面辐照不均匀性的变化。

利用消衍射透镜列阵及光谱色散平滑实现焦斑均匀辐照

提出将空间域的透镜列阵法和时间域的光谱色散平滑法结合起来实现靶面的均匀辐照．消衍射型透镜列阵能获得边缘陡峭且顶部较平坦的准近场焦斑，光谱色散平滑则能有效地抹平焦斑内部由多光束干涉引起的细密条纹．数值结果显示，通过该方案能获得均匀性较好的焦斑．进一步分析了光谱色散平滑单元中位相调制和光栅的参数对辐照均匀性的影响，发现参数的选取要在焦斑均匀性和能量利用率之间取得合理平衡，以在整体上获得最佳的均匀辐照效果．

列阵透镜对能量测量影响的分析

结合列阵透镜的透过率分析了其后的光场分布。列阵透镜由多个列阵元拼接而成，用以改善主透镜焦点附近能量分布的均匀性。列阵透镜在提高辐照均匀性的同时，给能量测量带来了不利的影响。这是由于经过列阵元的相邻子光束会产生干涉，干涉条纹处的激光能量密度和功率密度相应都大为增加，其数值在干涉区域中心处能上升到原来的4倍。更高的能量密度和功率密度对能量计提出了更苛刻的要求。在没有采取适当措施的时候使用，就会损坏能量计。

厄米-高斯光束中带宽对横向强度分布均匀性的影响

使用惠更斯-菲涅耳衍射积分和傅里叶变换，推导了横向模式为厄米高斯的激光束通过硬边光阑的传输表达式。利用所得公式通过数值计算详细分析了光束的频带宽度对光束横向强度分布的影响。分析发现激光束通过硬边光阑后会出现大量的强度尖峰，引起近场的强度分布不均匀。然而，当带宽增加时，强度尖峰的数量减少，幅度减小，光束的均匀性得到改善。在远场，光束的横向强度分布没有强度尖峰出现，但宽度随带宽的增加而减小。因此带宽增加会带来近场强度匀滑化和远场光束宽度变窄的效应。另外，数值结果表明带宽对模指数为1和2的厄米-高斯光束的强度分

Beam smoothing by lens array with spectral dispersion

A scheme of combining technology of lens array (LA) and smoothing by spectral dispersion (SSD) is introduced to improve the irradiation uniformity in laser fusion based on the earlier works on LA. The feasibility of the scheme is also analyzed by numerical simulation. It shows that a focal pattern with flat-top and sharp-edge profile could be obtained, and the irradiation nonuniformity can fall down from 14% with only LA to 3% with both SSD and LA. And this smoothing scheme is depended less on the incidence comparing to other smoothing methods. The preliminary experiment has demonstrated its effectiveness. (c) 2006 Elsevier B.V. All rights reserved.