Changes in motor planning of feedforward postural responses of the trunk muscles in low back pain

Changes in trunk muscle recruitment have been identified in people with low-back pain (LBP). These differences may be due to changes in the planning of the motor response or due to delayed transmission of the descending motor command in the nervous system. These two possibilities were investigated by comparison of the effect of task complexity on the feedforward postural response of the trunk muscles associated with rapid arm movement in people with and without LBP. Task complexity was increased by variation of the expectation for a command to either abduct or flex the upper limb. The onsets of electromyographic activity (EMG) of the abdominal and deltoid muscles were measured. In control subjects, while the reaction time of deltoid and the superficial abdominal muscles increased with task complexity, the reaction time of transversus abdominis (TrA) was constant. However, in subjects with LBP, the reaction time of TrA increased along with the other muscles as task complexity was increased. While inhibition of the descending motor command cannot be excluded, it is more likely that the change in recruitment M of TrA represents a more complex change in organisation of the postural response.

Planning for institutional capacity building in war-torn areas: the case of Jaffna, Sri Lanka

This paper examines an attempt to build capacity and empower local institutions in war-torn Jaffna,, on the northern tip of Sri Lanka. A participatory approach that is aimed at social empowerment is seen to be possible even under the most restrictive of political environments. However, whether or not the development intervention provides a foundation for longer-term improvement depends on the extent to which institutional capacity is built. Through an examination of the Jaffna Reconstruction Project, it is argued that if any of the ingredients of this institutional capacity are missing, not only will the 'islands of participation and empowerment' that are built by the development initiative be short-lived, but there may also be a negligible contribution to building a foundation for longer-term improvement in quality of life. (C) 2001 Elsevier Science Ltd. All rights reserved.

High dependency units: Issues to consider in their planning

This review discusses the issues to be considered in establishing new or extending existing high dependency unit (HDU) services. A defined high dependency service becomes cost-effective when patient care requires more than one nurse for three patients. Professional guidelines for HDUs vary and there are no national accreditation criteria. Casemix and service delivery specifications for the HDU need to be defined and agreed upon within the institution. Establishing a new HDU service requires changes to care delivery. Many potential HDU patients are currently managed in general wards or in the intensive care unit. The service should be discussed widely and marketed within the institution, and the development of defined working relationships with the ICU and primary care teams oil the wards is mandatory.

Beneficial effects of air inclusions on the performance of ethylene vinyl acetate (EVA) mouthguard material

Objective: To investigate the impact characteristics of an ethylene vinyl acetate (EVA) mouthguard material with regulated air inclusions, which included various air cell volumes and wall thickness between air cells. In particular, the aim was to identify the magnitude and direction of forces within the impacts. Method: EVA mouthguard material, A mm thick and with and without air inclusions, was impacted with a constant force impact pendulum with an energy of 4.4 J and a velocity of 3 m/s. Transmitted forces through the EVA material were measured using an accelerometer, which also allowed the determination of force direction and magnitude within the impacts. Results: Statistically significant reductions in the transmitted forces were observed with all the air inclusion materials when compared with EVA without air inclusions. Maximum transmitted force through one air inclusion material was reduced by 32%. Force rebound was eliminated in one material, and reduced second force impulses were observed in all the air inclusion materials. Conclusion: The regulated air inclusions improved the impact characteristics of the EVA mouthguard material, the material most commonly used in mouthguards world wide.

Effect of ethylene vinyl acetate (EVA) closed cell foam on transmitted forces in mouthguard material

Objectives: To compare transmitted forces through ethylene vinyl acetate (EVA) mouthguard material and the same EVA material with gas inclusions in the form of a closed cell foam. Method: EVA mouthguard materials with and without foam gas inclusions and 4 mm thick were impacted with a constant force from an impact pendulum. Various porosity levels in the foam materials were produced by 1%, 5%, and 10% by weight foaming agent. The forces transmitted through the EVA after energy absorption by the test materials were measured with a force sensor and compared. Results: Only minor non-significant differences in transmitted forces through the EVA with and without foam were shown. Conclusions: The inclusion of gas in the form of a closed cell foam in 4 mm thick EVA mouthguard materials did not improve the impact performance of the EVA mouthguard material.

The devolution of indigenous local government authority in Queensland: Opportunities for statutory planning

Government policy change to self detennination over the past two decades has gradually given rise to various structures of Indigenous self government across Australia. Indigenous Local Government Authorities (LGAs) are the governing structure which receive the greatest devolution of State authority, especially those found in Queensland and the Northern Territory. Their statutory basis has developed over a relatively short period of time and is still very much evolving. This paper explores what opportunities exist for Indigenous LGAs to adopt statutory planning mechanisms.

A design method for superconducting MRI magnets with ferromagnetic material

The emphasis of this work is on the optimal design of MRI magnets with both superconducting coils and ferromagnetic rings. The work is directed to the automated design of MRI magnet systems containing superconducting wire and both `cold' and `warm' iron. Details of the optimization procedure are given and the results show combined superconducting and iron material MRI magnets with excellent field characteristics. Strong, homogeneous central magnetic fields are produced with little stray or external field leakage. The field calculations are performed using a semi-analytical method for both current coil and iron material sources. Design examples for symmetric, open and asymmetric clinical MRI magnets containing both superconducting coils and ferromagnetic material are presented.

Rapid field calculations for the effect of ferromagnetic material in MRI magnet design

Magnetic resonance imaging (MRI) magnets have very stringent constraints on the homogeneity of the static magnetic field that they generate over desired imaging regions. The magnet system also preferably generates very little stray field external to its structure, so that ease of siting and safety are assured. This work concentrates on deriving, means of rapidly computing the effect of 'cold' and 'warm' ferromagnetic material in or around the superconducting magnet system, so as to facilitate the automated design of hybrid material MR magnets. A complete scheme for the direct calculation of the spherical harmonics of the magnetic field generated by a circular ring of ferromagnetic material is derived under the conditions of arbitrary external magnetizing fields. The magnetic field produced by the superconducting coils in the system is computed using previously developed methods. The final, hybrid algorithm is fast enough for use in large-scale optimization methods. The resultant fields from a practical example of a 4 T, clinical MRI magnet containing both superconducting coils and magnetic material are presented.