Study on the method of freeway incident detection using wireless positioning terminal

Improving the performance of a incident detection system was essential to minimize the effect of incidents. A new method of incident detection was brought forward in this paper based on an in-car terminal which consisted of GPS module, GSM module and control module as well as some optional parts such as airbag sensors, mobile phone positioning system (MPPS) module, etc. When a driver or vehicle discovered the freeway incident and initiated an alarm report the incident location information located by GPS, MPPS or both would be automatically send to a transport management center (TMC), then the TMC would confirm the accident with a closed-circuit television (CCTV) or other approaches. In this method, detection rate (DR), time to detect (TTD) and false alarm rate (FAR) were more important performance targets. Finally, some feasible means such as management mode, education mode and suitable accident confirming approaches had been put forward to improve these targets.

A numerical method to quantify the axial shortening of vertical elements in concrete buildings

Differential axial shortening, distortion and deformation in high rise buildings is a serious concern. They are caused by three time dependent modes of volume change; “shrinkage”, “creep” and “elastic shortening” that takes place in every concrete element during and after construction. Vertical concrete components in a high rise building are sized and designed based on their strength demand to carry gravity and lateral loads. Therefore, columns and walls are sized, shaped and reinforced differently with varying concrete grades and volume to surface area ratios. These structural components may be subjected to the detrimental effects of differential axial shortening that escalates with increasing the height of buildings. This can have an adverse impact on other structural and non-structural elements. Limited procedures are available to quantify axial shortening, and the results obtained from them differ because each procedure is based on various assumptions and limited to few parameters. All these prompt to a need to develop an accurate numerical procedure to quantify the axial shortening of concrete buildings taking into account the important time varying functions of (i) construction sequence (ii) Young’s Modulus and (iii) creep and shrinkage models associated with reinforced concrete. General assumptions are refined to minimize variability of creep and shrinkage parameters to improve accuracy of the results. Finite element techniques are used in the procedure that employs time history analysis along with compression only elements to simulate staged construction behaviour. This paper presents such a procedure and illustrates it through an example. Keywords: Differential Axial Shortening, Concrete Buildings, Creep and Shrinkage, Construction Sequence, Finite Element Method.

A method of lines approach for modelling saltwater intrusion in coastal aquifiers

The equations governing saltwater intrusion in coastal aquifers are complex. Backward Euler time stepping approaches are often used to advance the solution to these equations in time, which typically requires that small time steps be taken in order to ensure that an accurate solution is obtained. We show that a method of lines approach incorporating variable order backward differentiation formulas can greatly improve the efficiency of the time stepping process.

Toward a fuzzy domain ontology extraction method for adaptive e-learning

With the widespread applications of electronic learning (e-Learning) technologies to education at all levels, increasing number of online educational resources and messages are generated from the corresponding e-Learning environments. Nevertheless, it is quite difficult, if not totally impossible, for instructors to read through and analyze the online messages to predict the progress of their students on the fly. The main contribution of this paper is the illustration of a novel concept map generation mechanism which is underpinned by a fuzzy domain ontology extraction algorithm. The proposed mechanism can automatically construct concept maps based on the messages posted to online discussion forums. By browsing the concept maps, instructors can quickly identify the progress of their students and adjust the pedagogical sequence on the fly. Our initial experimental results reveal that the accuracy and the quality of the automatically generated concept maps are promising. Our research work opens the door to the development and application of intelligent software tools to enhance e-Learning.

Moderating drinking by correspondence : an evaluation of a new method of intervention

Recognizing the need to offer alternative methods of brief interventions, this study developed correspondence treatments for low-dependent problem drinkers and evaluated their impact. One hundred and twenty-one problem drinkers were recruited by media advertisements and were randomly allocated to a full cognitive behavioural treatment programme (CBT) or to a minimal intervention condition (MI) that gave information regarding alcohol misuse and instructions to record drinking. As predicted, CBT was more effective than MI in reducing alcohol consumption over the 4-month controlled trial period. CBT produced a 50% fall in consumption, bringing the average intake of subjects within recommended maximum levels. Treatment gains at 6 months were well maintained to 12 months. High levels of consumer satisfaction, a high representation of women and a substantial participation from isolated rural areas attested to the feasibility of the correspondence programme as an alternative treatment. However, some drinking occasions still involved high intake for a significant subgroup of subjects, and this issue will be addressed in future programmes. The results supported the use of correspondence delivery as a means of promoting early engagement and equity of access between city and country areas.

The failure of Australian legislation on indirect discrimination to detect the systemic racism which prevents Aboriginal people from fully participating in the workforce

Government figures put the current indigenous unemployment rate at around 23%, 3 times the unemployment rate for other Australians. This thesis aims to assess whether Australian indirect discrimination legislation can provide a remedy for one of the causes of indigenous unemployment - the systemic discrimination which can result from the mere operation of established procedures of recruitment and hiring. The impact of those practices on indigenous people is examined in the context of an analysis of anti-discrimination legislation and cases from all Australian jurisdictions from the time of the passing of the Racial Discrimination Act by the Commonwealth in 1975 to the present. The thesis finds a number of reasons why the legislation fails to provide equality of opportunity for indigenous people seeking to enter the workforce. In nearly all jurisdictions it is obscurely drafted, used mainly by educated middle class white women, and provides remedies which tend to be compensatory damages rather than change to recruitment policy. White dominance of the legal process has produced legislative and judicial definitions of "race" and "Aboriginality" which focus on biology rather than cultural difference. In the commissions and tribunals complaints of racial discrimination are often rejected on the grounds of being "vexatious" or "frivolous", not reaching the required standard of proof, or not showing a causal connection between race and the conduct complained of. In all jurisdictions the cornerstone of liability is whether a particular employment term, condition or practice is reasonable. The thesis evaluates the approaches taken by appellate courts, including the High Court, and concludes that there is a trend towards an interpretation of reasonableness which favours employer arguments such as economic rationalism, the maintenance of good industrial relations, managerial prerogative to hire and fire, and the protection of majority rights. The thesis recommends that separate, clearly drafted legislation should be passed to address indigenous disadvantage and that indigenous people should be involved in all stages of the process.

A differential kinetic spectrophotometric method for determination of three sulphanilamide artificial sweeteners with the aid of chemometrics

A simple and sensitive spectrophotometric method for the simultaneous determination of acesulfame-K, sodium cyclamate and saccharin sodium sweeteners in foodstuff samples has been researched and developed. This analytical method relies on the different kinetic rates of the analytes in their oxidative reaction with KMnO4 to produce the green manganate product in an alkaline solution. As the kinetic rates of acesulfame-K, sodium cyclamate and saccharin sodium were similar and their kinetic data seriously overlapped, chemometrics methods, such as partial least squares (PLS), principal component regression (PCR) and classical least squares (CLS), were applied to resolve the kinetic data. The results showed that the PLS prediction model performed somewhat better. The proposed method was then applied for the determination of the three sweeteners in foodstuff samples, and the results compared well with those obtained by the reference HPLC method.

Simultaneous kinetic-spectrophotometric determination of maltol and ethyl maltol in food samples by using chemometrics

A fast and accurate procedure has been researched and developed for the simultaneous determination of maltol and ethyl maltol, based on their reaction with iron(III) in the presence of o-phenanthroline in sulfuric acid medium. This reaction was the basis for an indirect kinetic spectrophotometric method, which followed the development of the pink ferroin product (λmax = 524 nm). The kinetic data were collected in the 370–900 nm range over 0–30 s. The optimized method indicates that individual analytes followed Beer’s law in the concentration range of 4.0–76.0 mg L−1 for both maltol and ethyl maltol. The LOD values of 1.6 mg L−1 for maltol and 1.4 mg L−1 for ethyl maltol agree well with those obtained by the alternative high performance liquid chromatography with ultraviolet detection (HPLC-UV). Three chemometrics methods, principal component regression (PCR), partial least squares (PLS) and principal component analysis–radial basis function–artificial neural networks (PC–RBF–ANN), were used to resolve the measured data with small kinetic differences between the two analytes as reflected by the development of the pink ferroin product. All three performed satisfactorily in the case of the synthetic verification samples, and in their application for the prediction of the analytes in several food products. The figures of merit for the analytes based on the multivariate models agreed well with those from the alternative HPLC-UV method involving the same samples.

A Numerical Solution Using an Adaptively Preconditioned Lanczos Method for a Class of Linear Systems Related with the Fractional Poisson Equation

This study considers the solution of a class of linear systems related with the fractional Poisson equation (FPE) (−∇2)α/2φ=g(x,y) with nonhomogeneous boundary conditions on a bounded domain. A numerical approximation to FPE is derived using a matrix representation of the Laplacian to generate a linear system of equations with its matrix A raised to the fractional power α/2. The solution of the linear system then requires the action of the matrix function f(A)=A−α/2 on a vector b. For large, sparse, and symmetric positive definite matrices, the Lanczos approximation generates f(A)b≈β0Vmf(Tm)e1. This method works well when both the analytic grade of A with respect to b and the residual for the linear system are sufficiently small. Memory constraints often require restarting the Lanczos decomposition; however this is not straightforward in the context of matrix function approximation. In this paper, we use the idea of thick-restart and adaptive preconditioning for solving linear systems to improve convergence of the Lanczos approximation. We give an error bound for the new method and illustrate its role in solving FPE. Numerical results are provided to gauge the performance of the proposed method relative to exact analytic solutions.

A pilot study utilising cross-age peer tutoring as a method of intervention for anxious adolescents

Anxiety disorders are the most common psychopathology experienced by young people, with up to 18% of adolescents developing an anxiety disorder. The consequences of these disorders, if left untreated, include impaired peer relationships, school absenteeism and self-concept problems. In addition, anxiety disorders may play a causal role in the development of depression in young people, precede eating disorders and predispose adolescents to substance abuse disorders. While the school is often chosen as a place to provide early intervention for this debilitating disorder, the fact that excessive anxiety is often not recognised in school and that young people are reluctant to seek help, makes identifying these adolescents difficult. Even when these young people are identified, there are problems in providing sensitive programs which are not stigmatising to them within a school setting. One method which may engage this adolescent population could be cross-age peer tutoring. This paper reports on a small pilot study using the “Worrybusters” program and a cross-age peer tutoring method to engage the anxious adolescents. These anxious secondary school students planned activities for teacher-referred anxious primary school students for a term in the high school setting and then delivered those activities to the younger students weekly in the next term in the primary school. Although the secondary school students decreased their scores on anxiety self-report measures there were no significant differences for primary school students’ self-reports. However, the primary school parent reports indicated a significant decrease in their child’s anxiety.

Practice as method : the ex/centric fixations project

In the past decade, scholars have proposed a range of terms to describe the relationship between practice and research in the creative arts, including increasingly nuanced definitions of practice-based research, practice-led research and practice-as-research. In this paper, I consider the efficacy of creative practice as method. I use the example of The Ex/Centric Fixations Project – a project in which I have embedded creative practice in a research project, rather than embedding research in a creative project. The Ex/Centric Fixations project investigates the way spectators interpret human experiences – especially human experiences of difference, marginalisation or discrimination – depicted onstage. In particular, it investigates the way postmodern performance writing strategies, and the presence of performing bodied to which the experience depicted can be attached, impacts on interpretations. It is part of a broader research project which examines the performativity of spectatorship, and intervenes in emergent debates about performance, ethics and spectatorship in the context of debate about whether live performance is a privileged site for the emergence of an ethical face-to-face encounter with the Other. Using the metaphor of the Mobius strip, I examines the way practice – as a method, rather than an output – has informed, influenced and problematised the broader research project.

Metal oxide nanofibres membranes assembled by spin-coating method

Ceramic membranes are of particular interest in many industrial processes due to their ability to function under extreme conditions while maintaining their chemical and thermal stability. Major structural deficiencies under conventional fabrication approach are pin-holes and cracks, and the dramatic losses of flux when pore sizes are reduced to enhance selectivity. We overcome these structural deficiencies by constructing hierarchically structured separation layer on a porous substrate using larger titanate nanofibres and smaller boehmite nanofibres. This yields a radical change in membrane texture. The differences in the porous supports have no substantial influences on the texture of resulting membranes. The membranes with top layer of nanofibres coated on different porous supports by spin-coating method have similar size of the filtration pores, which is in a range of 10–100 nm. These membranes are able to effectively filter out species larger than 60 nm at flow rates orders of magnitude greater than conventional membranes. The retention can attain more than 95%, while maintaining a high flux rate about 900 L m-2 h. The calcination after spin-coating creates solid linkages between the fibres and between fibres and substrate, in addition to convert boehmite into -alumina nanofibres. This reveals a new direction in membrane fabrication.

Low-fat oxidation may be a factor in obesity among men with schizophrenia

Objective: Obesity associated with atypical antipsychotic medications is an important clinical issue for people with schizophrenia. The purpose of this project was to determine whether there were any differences in resting energy expenditure (REE) and respiratory quotient (RQ) between men with schizophrenia and controls. Method: Thirty-one men with schizophrenia were individually matched for age and relative body weight with healthy, sedentary controls. Deuterium dilution was used to determine total body water and subsequently fat-free mass (FFM). Indirect calorimetry using a Deltatrac metabolic cart was used to determine REE and RQ. Results: When corrected for FFM, there was no significant difference in REE between the groups. However, fasting RQ was significantly higher in the men with schizophrenia than the controls. Conclusion: Men with schizophrenia oxidised proportionally less fat and more carbohydrate under resting conditions than healthy controls. These differences in substrate utilisation at rest may be an important consideration in obesity in this clinical group.

Numerical method and analytical technique of the modified anomalous subdiffusion equation with a nonlinear source term

In this paper, we consider a modified anomalous subdiffusion equation with a nonlinear source term for describing processes that become less anomalous as time progresses by the inclusion of a second fractional time derivative acting on the diffusion term. A new implicit difference method is constructed. The stability and convergence are discussed using a new energy method. Finally, some numerical examples are given. The numerical results demonstrate the effectiveness of theoretical analysis

Stability and convergence of an implicit numerical method for the non-linear fractional reaction-subdiffusion process

In this paper, we consider the following non-linear fractional reaction–subdiffusion process (NFR-SubDP): Formula where f(u, x, t) is a linear function of u, the function g(u, x, t) satisfies the Lipschitz condition and 0Dt1–{gamma} is the Riemann–Liouville time fractional partial derivative of order 1 – {gamma}. We propose a new computationally efficient numerical technique to simulate the process. Firstly, the NFR-SubDP is decoupled, which is equivalent to solving a non-linear fractional reaction–subdiffusion equation (NFR-SubDE). Secondly, we propose an implicit numerical method to approximate the NFR-SubDE. Thirdly, the stability and convergence of the method are discussed using a new energy method. Finally, some numerical examples are presented to show the application of the present technique. This method and supporting theoretical results can also be applied to fractional integrodifferential equations.