988 resultados para constant temperature
Resumo:
The effect of irradiation temperature on the polymer properties was investigated for the fluoroelastomer poly(tetrafluoroethylene-co-perfluoromethylvinyl ether) (TFE/PMVE). TFE/PMVE samples were gamma-irradiated to 150 kGy at temperatures ranging from 77 K to 373 K. Analysis of the sol/gel behaviour, tensile properties, and glass transition temperatures indicated that crosslinking commenced in the temperature range 195 to 263 K, for a dose of 150 kGy. The latter temperature was 13 K below the glass transition temperature. Crosslinking remained relatively constant to higher temperatures. Chain scission reactions were found to occur well below the glass transition temperature and increased at higher temperatures. The optimum temperature for the radiation crosslinking of TFE/PMVE, for the temperatures investigated, was 263 K. (C) 1998 Elsevier Science Ltd. All rights reserved.
Resumo:
An experimental study of the effect of fuel stagnation temperature on mixing in a supersonic hydrogen-air flame is described, The combustor consisted of a constant-area rectangular duct with a centrally located fuel-injection strut that spanned the width. A high-enthalpy stream of air was supplied by a free-piston shock tunnel, and heated hydrogen fuel, supplied by a gun-tunnel, was injected into the freestream as a coflowing planar jet. The freestream total enthalpies were 5.6, 6.5, and 9 MJ/kg, and fuel stagnation temperatures were 300, 450, and 700 K, Raising the fuel stagnation temperature increased the fuel velocity to be near that of the airstream and resulted in a decrease in the mixing rate, Even as the fuel and air velocities became equal, significant mixing still occurred because of a large difference in density, Increasing the freestream enthalpy reduced the difference between the initial air temperature and the adiabatic flame temperature, which in turn reduced the heat addition, and subsequently, the amount of pressure rise in the duct.
Resumo:
Survival and development time from egg to adult emergence of the diamondback moth, Plutella xylostella (L.), were determined at 19 constant and 14 alternating temperature regimes from 4 to 40degreesC. Plutella xylostella developed successfully front egg to adult emergence at constant temperatures from 8 to 32degreesC. At temperatures from 4 to 6degreesC or from 34 to 40degreesC, partial or complete development of individual stages or instars was possible, with third and fourth instars having the widest temperature limits. The insect developed successfully from egg to adult emergence under alternating regimes including temperatures as low as 4degreesC or as high as 38degreesC. The degree-day model, the logistic equation, and the Wang model were used to describe the relationships between temperature and development rate at both constant and alternating temperatures. The degree-day model described the relationships well from 10 to 30degreesC. The logistic equation and the Wang model fit the data well at temperatures 32degreesC. Under alternating regimes, all three models gave good simulations of development in the mid-temperature range, but only the logistic equation gave close simulations in the low temperature range, and none gave close or consistent simulations in the high temperature range. The distribution of development time was described satisfactorily by a Weibull function. These rate and time distribution functions provide tools for simulating population development of P. xylostella over a wide range of temperature conditions.
Resumo:
We examined effects of body size and temperature on swimming performance in juvenile estuarine crocodiles, Crocodylus porosus, over the size range of 30-110 cm total body length. Swimming performance, expressed as maximum sustainable swimming speed, was measured in a temperature- and flow-controlled swimming flume. Absolute sustainable swimming speed increased with body length, but length-specific swimming performance decreased as body length increased. Sustained swimming speed increased with temperature between 15degreesC and 23degreesC, remained constant between 23degrees and 33degreesC, and decreased as temperature rose above 33degreesC. Q(10)-values of swimming speed were 2.60 (+/- 0.091 SE) between 18degreesC and 23degreesC, and there were no differences in Q(10) between crocodiles of different sizes. The broad plateau of thermal independence in swimming speed observed in C. porosus may be of adaptive significance by allowing dispersal of juvenile animals at suboptimal body temperatures.
Resumo:
Dissertação de Mestrado, Biotecnologia em Controlo Biológico, 18 de Dezembro de 2013, Universidade dos Açores.
Resumo:
This paper reports on the structural and optical properties of Co-doped TiO2 thin films grown onto (0001)Al2O3 substrates by non-reactive pulsed laser deposition (PLD) using argon as buffer gas. It is shown that by keeping constant the substrate temperature at as low as 310 degrees C and varying only the background gas pressure between 7 Pa and 70 Pa, it is possible to grow either epitaxial rutile or pure anatase thin films, as well as films with a mixture of both polymorphs. The optical band gaps of the films are red shifted in comparison with the values usually reported for undoped TiO2, which is consistent with n-type doping of the TiO2 matrix. Such band gap red shift brings the absorption edge of the Co-doped TiO2 films into the visible region, which might favour their photocatalytic activity. Furthermore, the band gap red shift depends on the films' phase composition, increasing with the increase of the Urbach energy for increasing rutile content. (C) 2012 Elsevier B.V. All rights reserved.
Resumo:
The effects of food concentration and temperature on embryonic and postem-bryonic duration of three tropical species, Daphnia gessneri(1.5mm), Diaphanosoma sarsi(1.2mm) and Moina reticulata(0.8mm), were investigated as part of life cycle studies which included growth, body size and reproduction. These are the very first experimental studies undertaken on these species. The long-term growth experiments were performed under controlled laboratory conditions at all combinations of temperature (22"C, 27"C and 32"C) and constant food concentration (0.03, 0.05, 0.10, 0.25, 0.50 and 1.00 mgC/L) of the unicellular green alga Scenedesmus acutus.Animals were examined twice daily throughout their life cycle from the neonate to third adult instar. In all three species, temperature exerted the most powerful influence on embryonic duration but there was also a smaller food effect. In D. gessneri,postembry-onic durations remained more or less the same at food levels 0.25 mgC/L but were influenced by temperature. At food concentrations of 0.1 mgC/L or lower, postembryonic durations became increasingly prolonged, particularly at high temperatures. This threshold concentration is affected by temperature: in D. gessneri,it was 0.1 mgC/L at 22oC and 27oC but higher at 32oC (between 0.25 and 0.50 mgC/L). At the same temperature of 27oC, the food threshold level varied between species: it was higher (0.25 mgC/L) for D. sarsiand lower (0.05 mgC/L) for M. reticulatacompared with D. gessneri(0.1 mgC/L). In both embryonic and postembryonic durations there is a body size effect as the absolute durations were longest in the largest species and shortest in the smallest species In all three species, prolongation of postembryonic duration at combinations of high temperature and lowered food levels was accompanied by increased number of juvenile instars.
Resumo:
Polyimide co-polymers have been prepared based on different diamines as co-monomers: a diamine without CN groups and a novel synthesized diamine with two CN groups prepared by polycondensation reaction followed by thermal cyclodehydration. Dielectric spectroscopy measurements were performed and the dielectric complex function, ac conductivity and electric modulus of the co-polymers were investigated as a function of CN group content in the frequency range from 0.1 Hz to 107 Hz at temperatures from 25 to 260 °C. For all samples and temperatures above 150ºC, the dielectric constant increases with increasing temperature due to increaseing conductivity. The α-relaxation is just detected for the sample without CN groups, being this relaxation overlapped by the electrical conductivity contributions in the remaining samples. For the copolymer samples and the polymer with CN groups an important Maxwell-Wagner-Sillars contribution is detected. The mechanisms responsible for the dielectric relaxation, conduction process and electric modulus response have been discussed as a function of the CN groups content present in the samples.
Resumo:
To note the effect of temperature on survival, growth and fecundity, newly hatched (zero day old) snails Indoplanorbis exustus were cultured at 10 degrees, 15 degrees, 20 degrees, 25 degrees, 30 degrees and 35 degreescentigrades constant temperatures and room temperature (17.5 degrees - 32.5 degrees centigrades). Individuals exposed to 10 degrees centigrades died within 3 days while those reared at 15 degrees, 20 degrees, 25 degrees, 30 degrees, 35 degrees centigrades and room temperature survived for a period of 6, 27, 18, 16, 12 and 17 weeks respectively. An individual added on an average 0.21 mm and 0.45 mg, 0.35 mm and 7.94 mg, 0.63 mm and 15.5 mg, 0.81 mm and 27.18 mg, 1.07 mm and 41.48 mg and 0.78 mm and 31.2 mg to the shell diameter and body weight respectively at those temperatures per week. The snails cultured at 15 degrees centigrades died prior to attainment of sexual maturity. On an average, an individual produced 31.9 and 582.77, 54.86 and 902.18, 56.01 and 968.45, 49.32 and 798.68 and 62.34 and 1143.97 capsules and eggs respectively at 20 degrees, 25 degrees, 30 degrees, 35 degrees centigrades and room temperature (17.5 degrees - 32.5 degrees centigrades).
Resumo:
Despite its vector importance little attention is given to Aedes aegypti embryonic development. In this study, temperature influence on time course of Ae. aegypti larvae hatching and egg viability were evaluated. The dormancy state at the end of embryogenesis could be interrupted with a proper stimulus. Temperatures tested ranged between 12-36°C; the maximum temperature limit is 35°C and the minimum one is below 12°C. Egg viability between 16-31°C was above 80%. The definition of physiological embryonic parameters at this temperature range corroborates Ae. aegypti presence on tropical and subtropical world regions.
Resumo:
This is a participant study, quasi-experimental, of a before and after type. A quantitative approach of biophysiological measures was used, represented by the saturation of oxygen measured by pulse oximeter (SpO2), and recorded on three occasions: before, during and after the bedbath in critically ill patients hospitalized at the ICU of a University Hospital in Brazil. Objective: to compare the SpO2 in various stages of the bath, with and without control of water temperature. Data collection was performed between December 2007 and April 2008 on a convenience sample consisting of 30 patients aged over 18 who had classification in TISS-28 from level II. Results show that water temperature control means a lower variation of SpO2 (p<0.05). No marked differences in variation of saturation between men and women or between age groups were established. In conclusion, heated and constant water temperature during the bedbath is able to minimize the fall of SpO2 that occurs while handling patients during procedures.
Resumo:
The interrelation of curing time, curing temperature, strength, and reactions in lime-bentonite-water mixtures was examined. Samples were molded at constant density and moisture content and then cured for periods of from 1 to 56 days at constant temperatures that ranged from 5C to 60C. After the appropriate curing time the samples were tested for unconfined compressive strength. The broken samples were then analyzed by x-ray diffractometer and spectrophotometer to determine the identity of the reaction products present after each curing period. It was found that the strength gain of lime-clay mixtures cured at different temperatures is due to different phases of the complex reaction, lime & clay to CSH(gel) to CSH(II) to CSH(I) to tobermorite. The farther the reaction proceeds, the higher the strength. There was also evidence of lattice substitutions in the structure of the calcium silicate hydrates at curing temperatures of 50C and higher. No consistent relationship between time, temperature, strength, and the S/A ration of reaction products existed, but in order to achieve high strengths the apparent C/S ration had to be less than two. The curing temperature had an effect on the strength developed by a given amount of reacted silica in the cured lime-clay mixture, but at a given curing temperature the cured sample that had the largest amount of reacted silica gave the highest strength. Evidence was found to indicate that during the clay reaction some calcium is indeed adsorbed onto the clay structure rather than entering into a pozzolanic reaction. Finally, it was determined that it is possible to determine the amount of silica and alumina in lime-clay reaction products by spectrophotometric analysis with sufficient accuracy for comparison purposes. The spectrophotometric analysis techniques used during the investigation were simple and were not time consuming.
Resumo:
Con objeto de buscar información para un mejor control de Oxalis latifolia Kunth, se ha estudiado el efecto que presentan la temperatura y la humedad sobre la activación de sus bulbos, tanto en la forma común como en la forma Cornwall de la misma. Los bulbos de la mala hierba se mantuvieron en un refrigerador a +4°C durante 13, 20, 27, 41, 48 y 55 días. Se sacaron tres grupos de 30 bulbos de cada forma en cada fecha de muestreo y se colocaron a 21°C; 15 de ellos se mantuvieron en condiciones de sequía —no se regaron— y otros 15 en condiciones de humedad —añadiendo el agua necesaria—. Los resultados muestran que la activación ocurre durante un período prolongado de tiempo en ambas formas, tanto en seco como en húmedo. También se observó que los bulbos secos se activaron antes que los húmedos y los de la forma común antes que los Cornwall. Se observaron dos patrones de activación: los bulbos secos de la forma común generalmente presentaron una activación que sigue un patrón logarítmico, mientras que sus bulbos humedecidos mostraron una tendencia linear; los bulbos Cornwall se activaron con una tendencia exponencial en la mayoría de los casos. El tiempo medio requerido para la activación después del almacenamiento en frío fue constante en la forma común, sin embargo la activación de Cornwall fue más rápida cuanto más tiempo permanecieron almacenados en frío.
Resumo:
ABSTRACTCallisthene fasciculata Mart. is a tree belonging to the Vochysiaceae family. Its wood is moderately heavy and resistant and used to make poles, beams, and other structures. The aim of this work was to evaluate seed germination and the initial growth of seedlings of C. fasciculata at different temperatures and in different substrates. Seeds were collected from fruits in the Pantanal de Miranda, Mato Grosso do Sul state, Brazil. In one experiment, the seeds were subjected to constant temperatures of 20, 25, 30 and 35 °C and to alternating temperatures of 20-30 and 25-35 °C (on paper substrate). In another experiment, the seeds were subjected to temperatures of 20 and 25 °C on three substrates (sand, vermiculite and between paper) in a germinator. The experiment had a randomized design, with four replicates of 25 seeds per treatment. The F-values obtained for germination indicated no significant effect of substrate or temperature on the final germination percentage. The analyses revealed no effect of a treatment interaction (temperature x substrate) on either germination or average germination time; however, a treatment interaction effect was observed on the germination speed index. The treatment combinations yielding the best performance were between paper substrate at 20 °C and sand substrate at 25 °C. There was a significant effect of the interaction between temperature and substrate on seedling growth, with increased root growth observed in the between paper substrate at 25 °C and increased aerial component growth in both sand at 20 °C and vermiculite at 25 °C. The between paper treatment at 25 °C yielded the greatest final seedling size. Between paper is the most recommended substrate for the production of seedlings due to its ease of handling and lower probability of contamination.
Resumo:
There is evidence that brain temperature (Tbrain) provides a more sensitive index than other core body temperatures in determining physical performance. However, no study has addressed whether the association between performance and increases in Tbrain in a temperate environment is dependent upon exercise intensity, and this was the primary aim of the present study. Adult male Wistar rats were subjected to constant exercise at three different speeds (18, 21, and 24 m/min) until the onset of volitional fatigue. Tbrain was continuously measured by a thermistor inserted through a brain guide cannula. Exercise induced a speed-dependent increase in Tbrain, with the fastest speed associated with a higher rate of Tbrain increase. Rats subjected to constant exercise had similar Tbrain values at the time of fatigue, although a pronounced individual variability was observed (38.7-41.7°C). There were negative correlations between the rate of Tbrain increase and performance for all speeds that were studied. These results indicate that performance during constant exercise is negatively associated with the increase in Tbrain, particularly with its rate of increase. We then investigated how an incremental-speed protocol affected the association between the increase in Tbrain and performance. At volitional fatigue, Tbrain was lower during incremental exercise compared with the Tbrain resulting from constant exercise (39.3±0.3 vs 40.3±0.1°C; P<0.05), and no association between the rate of Tbrain increase and performance was observed. These findings suggest that the influence of Tbrain on performance under temperate conditions is dependent on exercise protocol.