Physical soil characteristics of waterlogged and saline lands of five districts of Haryana, India

Physical characteristics of waterlogged and saline soils of five districts, namely Rohtak, Faridabad, Gurgaon, Sonipat and Jhajjar, of Haryana were studied to evaluate the aquaculture potential. The soil samples from 76 sites were procured and analysed for pH, electrical conductivity, soil particles and water retention capacity, since the knowledge of these parameters is essential for the preliminary evaluation of a site for aqua-farming. Six soil types were identified and clay-loam was observed to be the maximum at 45 (59.21%) sites, followed by silty-clay loam at 14 (18.42%), sandy-clay loam at six (7.89%), silty-loam at four (5.26%), sandy-loam at four (5.26%) and loam at three (3.94%) sites. The pH of soil indicated moderate to high alkaline conditions ranging between 8.01and 9.00 at 53 (69.73%) sites, 9.01 and 10.00 at 17 (22.36%) sites, and low between 7.01 and 8.00 at six (7.89%) sites. The electrical conductivity was found to range between <1 and 10 mmho cmˉ¹ with the value of <1.0 mmho cmˉ¹ at 36 (47.36%) sites. The water retention capacity was observed mostly to be moderate. The paper describes the interrelationship between these parameters with reference to the suitability for aqua-farming.

Soil conditioning under London

The CTRL Contract 220 covered 7.5km twin-bore tunnels excavated between late 2002 and early 2004 from Stratford Box to St Pancras station in Central London. To ensure efficient machine operation as well as the transport and disposal of soil, soil conditioning treatments were applied. Specifically, the foam injection ratio (FIR) and the polymer injection ratio (PIR) (injected volume of foam and polymer solution expressed as a percentage of the excavated soil volume) were employed. It was found that carefully selected soil conditioning allowed chamber pressures of 200kPa or more to be accurately controlled in the stiff London Clay and to an extent, in the very stiff clays of the Lambeth Group. Average FIRs of 50% and PIRs of 7 and 9% were used in the Thanet Sand and in the Lambeth Group Clays. In contrast, much lower quantities of foam were used in the London Clay.

Sustainable binders for soil stabilisation

Portland cement is the most commonly and widely used binder in ground improvement soil stabilisation applications. However, many changes are now affecting the selection and application of stabilisation additives. These include the significant environmental impacts of Portland cement, increased use of industrial by-products and their variability, increased range of application of binders and the development of alternative cements and novel additives with enhanced environmental and technical performance. This paper presents results from a number of research projects on the application of a number of Portland cement-blended binders, which offer sustainability advantages over Portland cement alone, in soil stabilisation. The blend materials included ground granulated blastfurnace slag, pulverised fuel ash, cement kiln dust, zeolite and reactive magnesia and stabilised soils, ranging from sand and gravel to clay, and were assessed based on their mechanical performance and durability. The results are presented in terms of strength and durability enhancements offered by those blended binders.

Analysis of case histories on deep excavations in marine clay

Two case histories on deep excavation of marine clay are used to study the use of a decision-making tool based on a new deign method called the Mobilized Strength Design (MSD) method which allows the designer to use a simple method of predicting ground displacements during deep excavation. This application can approximately satisfy both safety and serviceability requirements by predicting stresses and displacements under working conditions by introducing the concept of "Mobilizable soil strength". The new method accommodates a number of features which are important to design of underground construction between retaining walls, including different deformation mechanism in different stages of excavation. The influence of wall depth, wall flexibility and stratified ground are the major focus of this paper. These developments should make it possible for a design engineer to take informed decisions on the influence of wall stiffness, or on the need for a jet-grouted base slab, for example, without having to conduct project-specific Finite Element Analysis.

Faecal pellets in deep marine soft clay crusts: Implications for hot-oil pipeline design

In recent years, the presence of crusts within near surface sediments found in deep water locations off the west coast of Angola has been of interest to hot-oil pipeline designers. The origin for these crusts is considered to be of biological origin, based on the observation of thousands of faecal pellets in natural crust core samples. This paper presents the results of laboratory tests undertaken on natural and faecal pellet-only samples. These tests investigate the role faecal pellets play in modifying the gemechanical behaviour of clayey sediments. It is found that faecal pellets are able to significantly alter both the strength and the average grain-size of natural sediments, and therefore, influence the permeability and stiffness. Hot-oil pipelines self-embed into and subsequent shear on crusts containing faecal pellets. Being able to predict the time required for installed pipelines to consolidate the underlying sediment and thus, how soon after pipe-laying, the interface strength will develop is of great interest to pipeline designers. It is concluded from wet-sieving samples before and after oedometer tests, that the process of pipe laying is unlikely to destroy pellets. They will therefore, be a major constituent of the sediment subject to soil-pipeline shearing behaviour during axial pipe-walking and lateral buckling. Based on the presented results, a discussion highlighting the key implications for pipeline design is therefore provided. Copyright © 2011 by ASME.

Seismically-induced displacements of a suction caisson in soft clay

The seismic design for offshore foundations is based predominantly on experience onshore. This paper describes the results of dynamic centrifuge tests performed to validate the performance of a suction caisson installed in normally consolidated clay. The main objective is to evaluate the likely plastic displacement under different shaking levels. Permanent displacement results indicate that the displacements experienced are well within the allowable movement for the foundation considered, even though a strength based design approach would consider this to be a failure. Larger earthquakes are seen to produce comparatively smaller displacements. It is concluded that the when designing for seismic loading, if some displacement is permissible then a performance-based approach allowing some displacement proves significantly less conservative than a purely strength-based design. It is also concluded that dynamic response analyses should consider the strength of soil, as this can act as a fuse against large amplitude shear waves. © 2011 Taylor & Francis Group, London.

The nature and origin of deep ocean clay crust from the Gulf of Guinea

Deep ocean sediments off the west coast of Africa exhibit a peculiar undrained strength profile in the form of a crust, albeit of exceptionally high water content, overlying normally consolidated clay. Hot-oil pipelines are installed into these crustal sediments, so their origins and characteristics are of great interest to pipeline designers. This paper provides evidence for the presence of burrowing invertebrates in crust material, and for the way sediment properties are modified through their creation of burrows, and through the deposition of faecal pellets. A variety of imaging techniques are used to make these connections, including photography, scanning electron microscopy and X-ray computer tomography. However, the essential investigative technology is simply the wet-sieving of natural cores, which reveals that up to 60% by dry mass of the crustal material can consist of smooth, highly regular, sand-sized capsules that have been identified as the faecal pellets of invertebrates such as polychaetes. Mechanical tests reveal that these pellets are quite robust under effective stresses of the order of 10 kPa, acting like sand grains within a matrix of fines. Their abundance correlates closely with the measured strength of the crust. While this can easily be accepted in the context of a pellet fraction as high as 60%, the question arises how a smaller proportion of pellets, such as 20%, is apparently able to enhance significantly the strength of a sediment that otherwise appears to be normally consolidated. A hypothesis is suggested based on the composition of the matrix of fines around the pellets. These appear to consist of agglomerates of clay platelets, which may be the result of the breakdown of pellets by other organisms. Their continued degradation at depths in excess of 1 m is taken to explain the progressive loss of crustal strength thereafter.

Modeling of strain rate effects on clay in simple shear

The response of clay is highly dependent on straining and loading rate. To obtain a realistic prediction of the response for time dependent problems, it is essential to use a model that accounts for rate effects in the stress-strain-strength properties of soils. The proposed model has been expanded from the existing SIMPLE DSS framework to account for the strain rate effects on clays in simple shear conditions. In accordance with the findings in the existing literature, soil response displays a unique relationship between shear strength and strain rate. The predicting model is illustrated with a limited test data. Copyright ASCE 2006.

Characterisation of a high plasticity marine clay using a T-bar penetrometer

A series of laboratory-scale T-bar penetrometer tests have been conducted on a clay bed virgin consolidated from reconstituted high plasticity marine clay. This investigation was mainly concerned with the effects on the penetration resistance of rate of penetration and the presence of free water on the surface of the clay bed. The rate of penetration varied between 0.005mm/s and 50mm/s. The results showed that the nature of soil resistance was 'undrained' over the range of speeds studied, and the resistance showed a marked viscous rate effect. The virgin consolidated clay bed exhibited an increase in penetration resistance by up to 35% for a factor 10 increase in rate of penetration much larger than values previously reported for kaolin. The presence of water on the surface of clay bed had a profound impact on penetration resistance, particularly on the remoulded strength obtained by taking the T-bar through successive penetration and extraction cycles. This was true even when the remoulding cycles were conducted without the T-bar breaking through the clay surface.

Fracturing pressure in clay

Hydraulic fracturing in clayey soils can be triggered by either tensile or shear failure. In this paper, the physical meanings of various equations to predict fracture initiation pressure proposed in the past are discussed using the cavity expansion theory. In particular, when fracturing pressure is plotted against initial confining pressure, published laboratory test results as well as analytical models show a linear relationship. When the slope is close to 2, fracture is initiated by tensile failure of the clay, whereas when the slope is close to 1, it is initiated by shear failure of the clay. In this study, the analytical models, validated only on laboratory test data to date, were applied to unique data from field grouting work in which extensive soil fracturing was carried out to improve the mechanical characteristics of the soft silty clay underlying a bell tower in Venice, Italy. By a careful assessment of initial confining pressure in the field, the variation in recorded injection pressures with confining pressure was examined. Results suggest that the fractures at this site were likely to be initiated by shear failure of the clay, and the values were similar to what was predicted by the model with the shear failure criterion. © 2013 American Society of Civil Engineers.