Estudo de dormentes de aço sob solicitações verticais, longitudinais e transversais em via permanente ferroviária

This article presents the results of research conducted on full-scale models, studying the behavior of steel sleepers under the action of static loads, in vertical, longitudinal and transverse directions. For the research models were run with rails TR-68, fixed with elastic system on seven sleepers each type, separately, embedded in standard ballast with 35 cm height and on the basis of compacted soil with 30 cm thick. For the load tests were constructed using reaction systems of vertical and horizontal forces with the objective of applying the requests. The system of readings and data acquisition was fully computerized, obtaining in real time the values of forces and displacements. The results were compared with those installed in the same way with sleepers of wood, mono-block and bi-block prestressed concrete. The analyzed results provided unprecedented parameters in Brazil and of great importance for the design of modern railway permanent way, using steel sleepers.

Desenvolvimento de um sistema de telemetria para monitoramento térmico em casas de vegetação

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Magnetometric exploration in intrusive basic with evidence of gold in northern region of the Camaquã Sedimentary Basin (RS)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Mudanças climáticas previstas para o final do século afetam o desempenho e o desenvolvimento esquelético de larvas de tambaqui (Colossoma macropomum)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização espectral de espécies de Mata Atlântica de Interior em nível foliar e de copa

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Processamento e restituição digital de fotografias aéreas coloridas para estudo da cobertura vegetal

This work aimed to apply geoprocessing techniques to identify and to quantify the types of vegetal coverings in part of the county Botucatu – SP, having been divided into three phases: acquisition of data; georeferencing based on the digital topographic maps in 1:50000 scale and finally the thematic maps were generated. The methodology used to the analogical aerial photographics georeferencing showed efficient, considering that it was based on scientific procedures of residues

Processamento e restituição digital de fotografias aéreas coloridas para estudo da cobertura vegetal

This work aimed to apply geoprocessing techniques to identify and to quantify the types of vegetal coverings in part of the county Botucatu – SP, having been divided into three phases: acquisition of data; georeferencing based on the digital topographic maps in 1:50000 scale and finally the thematic maps were generated. The methodology used to the analogical aerial photographics georeferencing showed efficient, considering that it was based on scientific procedures of residues analysis and the positioning central was classified as A, according to the Cartographic Precision Pattern.

Sistema fotovoltaico monocristalino para bombeamento de água

Since ancient times, it has been a huge challenge to all people around the world to manage to get their fresh water, keeping it clean and providing it to every human being, so that it can be used for their daily needs. This is especially true for small properties in the countryside and in isolated areas with low demographic density. Pumping the water in those regions is a solution that rationalizes its use in domestic chores, in animal rearing and in the irrigation systems of cultivated areas. Making feasible local, renewable and non-polluted energetic alternatives is the aim for those areas that are usually far away from the public electric network. Using photovoltaic solar energy is the alternative now proposed. For this objective was built a system with two monocrystalline panels, one pump, two water tanks, two level sensors and a solenoid valve to pump water, using a pump powered an array of monocrystalline solar panels. The main goal was to compare their rate of water flow and their energy consumption. The use of one data acquisition equipment allowed collecting meteorological, electrical and hydraulic values, and also serving for the control and activation of the pumping system. During four months in a row as from April 2009, arrangements with one or two panels were tested. Mathematics correlations and adjustment lines were used to interpret the behavior of obtained dataset. During the analyzed period the system followed the linear equations with great accuracy. The daily average amount of water pumped by the several tested arrays stayed between 1,100 and 2,500 liters, and that is enough to supply a small rural property. The pumping system with two panels effectively showed the major amount of water, but a system with one panel can be an economical solution until 1,500 liters on day. It did not characterize a direct relationship between power or quantity of photovoltaic panels and daily outflow of water pumping.

Monitoramento do tempo de prensagem e do comportamento da temperatura através da espessura de painéis LVL (Laminated veneer lumber)

The aim of this study was to analyze the behavior of the flow of heat (temperature) through the thickness of panels LVL (Laminated veneer lumber) produced with phenol formaldehyde adhesive, in laboratorial and industrial scales. Experimental program was conducted with five LVL panels (three produced in laboratorial scale and two in industrial scale) with different arrangements of a mix of commercial veneers from tropical pinus from the south region of Sao Paulo State, Brazil, bonded using phenol formaldehyde adhesive. The temperature inside the panels during the pressing process was evaluated using thermocouples type T (cooper-constantan), installed mostly in the center of the glue lines and connected to a data acquisition system. The graphics of temperature as a function of the time showed a gradual increase of temperature up to pre-set values, remaining constant from them. The temperature reached at the center of the panels was adequate to promote the curing of the adhesive. These pre-set values were similar to the minimum values presented by other authors and manufacturers of these adhesives that affirm that temperatures above 100ºC at the center of laminated panels bonded with phenolic adhesives are sufficient to ensure proper cure of the resin. The time necessary for curing of the adhesives confirmed the validity of practical expressions provided by adhesive manufacturers.

Interpretação racional do ensaio DPL

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aprimoramento de um baropodômetro eletrônico e análise de estabiliometria em voluntários com escoliose

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Introdução à identificação de sistemas utilizando o System Identification Toolbox do MATLAB em conjunto com o Arduino para o laboratório de controle linear

The education designed and planned in a clear and objective manner is of paramount importance for universities to prepare competent professionals for the labor market, and above all can serve the population with an efficient work. Specifically, in relation to engineering, conducting classes in the laboratories it is very important for the application of theory and development of the practical part of the student. The planning and preparation of laboratories, as well as laboratory equipment and activities should be developed in a succinct and clear way, showing to students how to apply in practice what has been learned in theory and often shows them why and where it can be used when they become engineers. This work uses the MATLAB together with the System Identification Toolbox and Arduino for the identification of linear systems in Linear Control Lab. MATLAB is a widely used program in the engineering area for numerical computation, signal processing, graphing, system identification, among other functions. Thus the introduction to MATLAB and consequently the identification of systems using the System Identification Toolbox becomes relevant in the formation of students to thereafter when necessary to identify a system the base and the concept has been seen. For this procedure the open source platform Arduino was used as a data acquisition board being the same also introduced to the student, offering them a range of software and hardware for learning, giving you every day more luggage to their training

Proposta de controlador de carga com MPPT utilizando LabVIEW

This paper presents one proposal of the energy management's model system using photovoltaic panels. The module proposed seeks to monitor photovoltaic panels, which have intermittency in power generation caused by environmental or load conditions, in order to control the coupling between the panel and the load - through the charge controller, of aiming that the panel's operation will be always on the maximum power transfer point as possible. For this, it used the maximum power point tracking technique - MPPT, implemented in LabVIEW software, also utilizing the data acquisition card NI myDAQ. In addition, it was implemented the controller access remote module, from the sharing of network data, so the panels performance can be through a tablet, monitored and controlled with no need for direct contact with the Supervisory server

Avaliação dos níveis de vibração no operador de um trator agrícola ensaiado em pista normatizada em diferentes velocidades de deslocamento

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Aprimoramento de um baropodômetro eletrônico e análise de estabiliometria em voluntários com escoliose

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)