How does solvent molecular size affect the microscopic structure in polymer solutions?

Monte Carlo simulation has been used to investigate the effects of linear solvent molecular size on polymer chain conformation in solutions. Increasing the solvent molecular size leads to shrinkage of the polymer chains and increase of the critical overlap concentrations. The root-mean-square radius of gyration of polymer chains (R-g) is less sensitive to the variation of polymer concentration in solutions of larger solvent molecules. In addition, the dependency of R-g on polymer concentration under normal solvent conditions and solvent molecular size is in good agreement with scaling laws. When the solvent molecular size approaches the ideal end-to-end distance of the polymer chain, an extra aggregation of polymer chains occurs, and the solvent becomes the so-called medium-sized solvent. When the size of solvent molecules is smaller than the medium size, the polymer chains are swollen or partially swollen. However, when the size of solvent molecules is larger than the medium size, the polymer coils shrink and segregate, enwrapped by the large solvent molecules.

大气季节内振荡对东亚夏季风活动的影响研究

利用ERA40逐日再分析资料、NCEP/NCAR2逐日再分析资料、中国740个测站日降水资料、上海台风研究所提供的西太平洋热带气旋资料、Kaplan等重建的月平均SSTA资料、NOAA逐日长波辐射（OLR）等资料，应用离散功率谱分析、带通滤波、EOF分析等统计方法，研究了东亚夏季风(EASM）的移动特征、东亚地区季节内振荡(ISO)的基本特征、季节内振荡对东亚夏季风活动的影响、季节内振荡对东亚夏季风异常活动的影响机理。主要结论如下： （1）综合动力和热力因素定义了可动态描述东亚夏季风移动和强度的指数，并利用该指数研究了东亚夏季风的爆发和移动的季节内变化及其年际和年代际变化特征。研究发现，气候平均东亚夏季风前沿分别在28候、33候、36候、38候、40候、44候出现了明显的跳跃。东亚夏季风活动具有显著的年际变率，主要由于季风前沿在某些区域异常停滞和突然跨越北跳或南撤引起，造成中国东部旱涝灾害频繁发生。东亚夏季风的活动具有明显的年代际变化，在1965年、1980年、1994年发生了突变，造成中国东部降水由“南旱北涝”向“南涝北旱”的转变。 （2）东亚季风区季节内变化具有10~25d和30~60d两个波段的季节内振荡周期，以30-60d为主。存在三个主要低频模态，第一模态主要表征了EASM在长江中下游和华北地区活动期间的低频形势；第二模态印度洋-菲律宾由低频气旋式环流控制，主要表现了ISO在EASM爆发期间的低频形势；第三模态主要出现在EASM在华南和淮河活动期间的低频形势。第一模态和第三模态是代表东亚夏季风活动异常的主要低频形势。 （3）热带和副热带地区ISO总是沿垂直切变风的垂直方向传播。因此，在南海-菲律宾东北风垂直切变和副热带西太平洋北风垂直切变下，大气热源激发菲律宾附近交替出现的低频气旋和低频反气旋不断向西北传播，副热带西太平洋ISO以向西传播为主。中高纬度地区，乌拉尔山附近ISO以向东、向南移动或局地振荡为主；北太平洋中部ISO在某些情况下向南、向西传播。 （4）季风爆发期，伴随着热带东印度洋到菲律宾一系列低频气旋和低频反气旋， 冷空气向南输送，10~25天和30~60天季节内振荡低频气旋同时传入南海加快了南海夏季风的爆发。在气候态下，ISO活动表现的欧亚- 太平洋（EAP）以及太平洋-北美（PNA）低频波列分布特征(本文提出的EAP和PNA低频波列与传统意义上的二维定点相关得到的波列不同)。这种低频分布形式使得欧亚和太平洋中高纬度的槽、脊及太平洋副热带高压稳定、加强，东亚地区的低频波列则成为热带和中高纬度ISO相互作用影响东亚夏季风活动的纽带。不同的阶段表现不同的低频模态，30~60d低频模态的转变加快了EASM推进过程中跳跃性；30-60d低频模态的维持使得EASM前沿相对停滞。 （5）30-60d滤波场，菲律宾海域交替出现的低频气旋和低频反气旋不断向西北传播到南海-西太平洋一带。当南海-西太平洋地区低频气旋活跃时，季风槽加强、东伸，季风槽内热带气旋（TC）频数增加；当南海-西太平洋低频反气旋活跃时，季风槽减弱、西退，TC处于间歇期，生成位置不集中。 （6）在El Nino态下，大气季节内振荡偏弱，北传特征不明显，但ISO由中高纬度北太平洋中部向南和副热带西太平洋向西的传播特征显著，东亚地区ISO活动以第三模态为主，EASM集中停滞在华南和淮河流域，常伴随着持续性区域暴雨的出现，易造成华南和江淮流域洪涝灾害，长江和华北持续干旱。在La Nina态下，大气季节内振荡活跃，且具有明显的向北传播特征，PNA低频波列显著，东亚地区ISO活动以第一模态单峰为主；EASM主要停滞在长江中下游和华北地区，这些地区出现异常持续强降水，华南和淮河流域多干旱；在El Nino态向La Nina态转换期，ISO活动以第一模态双峰为主，长江中下游常常出现二度梅。

THE COMPOUND EYE AS AN INDICATOR OF AGE AND SHRINKAGE IN ANTARCTIC KRILL

Laboratory studies have shown that Antarctic krill (Euphausia superba) shrink if maintained in conditions of low food availability. Recent studies have also demonstrated that E. superba individuals may be shrinking in the field during winter. If krill shrink during the winter, conclusions reached by length-frequency analysis may be unreliable because smaller animals may not necessarily be younger animals. In this study, the correlation between the body-length and the crystalline cone number of the compound eye was examined. Samples collected in the late summer show an apparent linear relationship between crystalline cone number and body-length. From a laboratory population, it appears that when krill shrink the crystalline cone number remains relatively unchanged. If crystalline cone number is little affected by shrinking, then the crystalline cone number may be a more reliable indicator of age than body-length alone. The ratio of crystalline cone number to body-length offers a method for detecting the effect of shrinking in natural populations of krill. On the basis of the crystalline cone number count, it appears from a field collection in early spring that E. superba do shrink during winter.

基于跟随领航者法的多UUV队形控制方法研究

本文主要研究基于跟随领航者法的多 UUV(unmanned underwater vehicle)队形控制。在 UUV 载体坐标系下建立系统的运动学模型,该模型是对笛卡尔坐标系下的运动学模型的改进,避免了极坐标系下奇异点的出现。该模型经过输入输出反馈线性化,获得稳定的队形控制器。同时,为了缩小队形控制律中的控制参数的调整范围,本文提出了辅助算法,在此基础上分析参数的有效范围。将队形控制律在多 UUV 数字仿真平台上验证,证实了改进的运动学模型和控制律的有效性。

热察绥地区过去300年土地利用覆被变化

The historical land use and land cover changes is one of the key issues in LUCC research. However, the achievement of China in this field doesn't match her position in the world yet. And the reliability of the quantitive records in Chinese historical literature, the basic data for historical land use research, has been doubted. This research focuses on Re-Cha-Sui, a typical area for the farming-pastoral region in the north of China, to make a detailed case study in this field. Based on a deep mining and calibration on the data from massive historical documents and land-use surveys, the author gives a detailed analysis on the administrative region evolution, historical population dynamics, reclamation policy, and the land statistic system. According to textual researches, parallel validation and physical geographical analysis, a unified land use series for recent 300 years, which founded on the results of modern land-use surveys, is constructed. And the thematic maps on the cultivation index for different counties in several temporal sections are plotted. Based on the endeavor above, the dynamic of forest and steppe is reconstructed as well. The temporal-spatial patterns of land use/land cover changes in the area is analyzed. And the influence of different driving forces are discussed. The main conclusions of the research are as followed: 1. The quantitive records in literatures on Re-Cha-Sui area are reflection of real amounts of croplands. It is practical to reconstruct a result comparable with the modern land-use surveys, based of a deep mining and considerate validation on historical documents. The unexceptional negative attitude towards the numerical records in historical documents is unnecessary. 2. In recent 300 years, 3 climax of reclamation appeared in Re-Cha-Sui area and altered the pure pastoral area into a farming-pastoral region. The interval were respectively the early time till mid time of the Qing dynasty, the end of the Qing dynasty till early time of the Republic of China(ROC), and the time after A.D. 1949. After the first expansion, the area of cropland in this region reached 2.0 million ha. Among them, Guisui area, which was most densely cultivated, had a cultivation index over 30%, which is similar with modern situation. The second expansion covered broader area, and the amount of cropland reached 3.5 million ha. The increase of farming area after 1949 is due to the recultivation of abandoned farmland. The current area of cropland in this region is 5.6 million ha. In the southern area where the land was reclaimed early, the amount on of the cropland has some fluctuation in 300 years. While in the new reclaimed area in the north, the area of cropland has kept the trend of increasing. 3. Due to the different natural conditions, most forests in Re-Cha-Sui area distribute in the mountain area of North Hebei province, and the upland of West Liaoning province, especially the former, which has a forest coverage near 70%. However, most of these forests were destroyed before the end of the Qing dynasty. In 1949, the natural forest near Chengde was nearly cleared up. They were partly renewed after 1949 due to plantation. 4. In the steppe zone such as northern Rehe, Suiyuan and Chahar, the area of steppe has a negative correlation with that of cropland. With the expansion of cropland, the percentage of steppe has shrunk from over 80% to 53%. In the mountain area of North Hebei province, steppe expanded with the shrinkage of forest, though cropland was expanding. The percentage once reached 60%, and then fell with the renew of forest. However, in the upland of West Liaoning province, the steppe shrink slowly from original 50% to current 26%, with the expansion of cropland. 5. The land use and land cover change in Re-Cha-Sui area in recent 300 years is driven by various factors, including human dimensions such as population, policy of the government, disorder of the society, cultural tradition, and natural factors such as climate change and natural disasters. Among them, pressure from surplus population is the basic driving force.

The dynamics of a topological change in a system of soap films

Hutzler, S., Saadatfar, M., van der Net, A., Weaire, D. and Cox, S.J. (2007) The dynamics of a topological change in a system of soap films. Coll. Surf. A, 323:123-131. Sponsorship: This research was supported by the European Space Agency (contracts 14914/02/NL/SH and 14308/00/NL/SH), Science Foundation Ireland. (RFP 05/REP/PHY00/6), and the EU program COST P21 (The Physics of droplets). SJC acknowledges support from EPSRC (EP/D071127/1). MS is supported by the Irish Higher Education Authority (PRTLI-IITAC).

Atomic layer deposition of copper for CMOS interconnects

This work concerns the atomic layer deposition (ALD) of copper. ALD is a technique that allows conformal coating of difficult topographies such as narrow trenches and holes or even shadowed regions. However, the deposition of pure metals has so far been less successful than the deposition of oxides except for a few exceptions. Challenges include difficulties associated with the reduction of the metal centre of the precursor at reasonable temperatures and the tendency of metals to agglomerate during the growth process. Cu is a metal of special technical interest as it is widely used for interconnects on CMOS devices. These interconnects are usually fabricated by electroplating, which requires the deposition of thin Cu seed layers onto the trenches and vias. Here, ALD is regarded as potential candidate for replacing the current PVD technique, which is expected to reach its limitations as the critical dimensions continue to shrink. This work is separated into two parts. In the first part, a laboratory-scale ALD reactor was constructed and used for the thermal ALD of Cu. In the second part, the potentials of the application of Cu ALD on industry scale fabrication were examined in a joint project with Applied Materials and Intel. Within this project precursors developed by industrial partners were evaluated on a 300 mm Applied Materials metal-ALD chamber modified with a direct RF-plasma source. A feature that makes ALD a popular technique among researchers is the possibility to produce high- level thin film coatings for micro-electronics and nano-technology with relatively simple laboratory- scale reactors. The advanced materials and surfaces group (AMSG) at Tyndall National Institute operates a range of home-built ALD reactors. In order to carry out Cu ALD experiments, modifications to the normal reactor design had to be made. For example a carrier gas mechanism was necessary to facilitate the transport of the low-volatile Cu precursors. Precursors evaluated included the readily available Cu(II)-diketonates Cu-bis(acetylacetonate), Cu-bis(2,2,6,6-tetramethyl-hepta-3,5-dionate) and Cu-bis(1,1,1,5,5,5-hexafluoacetylacetonate) as well as the Cu-ketoiminate Cu-bis(4N-ethylamino- pent-3-en-2-onate), which is also known under the trade name AbaCus (Air Liquide), and the Cu(I)- silylamide 1,3-diisopropyl-imidazolin-2-ylidene Cu(I) hexamethyldisilazide ([NHC]Cu(hmds)), which was developed at Carleton University Ottawa. Forming gas (10 % H2 in Ar) was used as reducing agent except in early experiments where formalin was used. With all precursors an extreme surface selectivity of the deposition process was observed and significant growth was only achieved on platinum-group metals. Improvements in the Cu deposition process were obtained with [NHC]Cu(hmds) compared with the Cu(II) complexes. A possible reason is the reduced oxidation state of the metal centre. Continuous Cu films were obtained on Pd and indications for saturated growth with a rate of about 0.4 Å/cycle were found for deposition at 220 °C. Deposits obtained on Ru consisted of separated islands. Although no continuous films could be obtained in this work the relatively high density of Cu islands obtained was a clear improvement as compared to the deposits grown with Cu(II) complexes. When ultra-thin Pd films were used as substrates, island growth was also observed. A likely reason for this extreme difference to the Cu films obtained on thicker Pd films is the lack of stress compensation within the thin films. The most likely source of stress compensation in the thicker Pd films is the formation of a graded interlayer between Pd and Cu by inter-diffusion. To obtain continuous Cu films on more materials, reduction of the growth temperature was required. This was achieved in the plasma assisted ALD experiments discussed in the second part of this work. The precursors evaluated included the AbaCus compound and CTA-1, an aliphatic Cu-bis(aminoalkoxide), which was supplied by Adeka Corp.. Depositions could be carried out at very low temperatures (60 °C Abacus, 30 °C CTA-1). Metallic Cu could be obtained on all substrate materials investigated, but the shape of the deposits varied significantly between the substrate materials. On most materials (Si, TaN, Al2O3, CDO) Cu grew in isolated nearly spherical islands even at temperatures as low as 30 °C. It was observed that the reason for the island formation is the coalescence of the initial islands to larger, spherical islands instead of forming a continuous film. On the other hand, the formation of nearly two-dimensional islands was observed on Ru. These islands grew together forming a conductive film after a reasonably small number of cycles. The resulting Cu films were of excellent crystal quality and had good electrical properties; e.g. a resistivity of 2.39 µΩ cm was measured for a 47 nm thick film. Moreover, conformal coating of narrow trenches (1 µm deep 100/1 aspect ratio) was demonstrated showing the feasibility of the ALD process.

Characterisation and application of fruit by-products as novel ingredients in gluten-free products

The physicochemical and nutritional properties of two fruit by-products were initially studied. Apple pomace (AP) contained a high level of fibre and pectin. The isolated AP pectin had a high level of methylation which developed viscous pastes. Orange pomace also had high levels of fibre and pectin, and it was an abundant source of minerals such as potassium and magnesium. Due to the fibrous properties of orange pomace flour, proofing and water addition were studied in a bread formulation. When added at levels greater than 6%, the loaf volume decreased. An optimised formulation and proofing time was derived using the optimisation tool; these consisted of 5.5% orange pomace, 94.6% water inclusion and with 49 minutes proofing. These optimised parameters doubled the total dietary fibre content of the bread compared to the original control. Pasting results showed how orange pomace inclusions reduced the final viscosity of the batter, reducing the occurrence of starch gelatinisation. Rheological properties i.e. the storage modulus (G') and complex modulus (G*) increased in the orange pomace batter compared to the control batter. This demonstrates how the orange pomace as an ingredient improved the robustness of the formulation. Sensory panellists scored the orange pomace bread comparably to the control bread. Milled apple pomace was studied as a potential novel ingredient in an extruded snack. Parameters studied included apple pomace addition, die head temperature and screw speed. As screw speed increased the favourable extrudate characteristics such as radical expansion ratio, porosity and specific volume decreased. The inclusion of apple pomace had a negative effect on extrudate characteristics at levels greater than 8% addition. Including apple pomace reduced the hardness and increased the crispiness of the snack. The optimised and validated formulation and extrusion process contained the following parameters: 7.7% apple pomace, 150°C die head temperature and a screw speed of 69 rpm.

Case base reduction using solution-space metrics

In this paper we propose a case base reduction technique which uses a metric defined on the solution space. The technique utilises the Generalised Shepard Nearest Neighbour (GSNN) algorithm to estimate nominal or real valued solutions in case bases with solution space metrics. An overview of GSNN and a generalised reduction technique, which subsumes some existing decremental methods, such as the Shrink algorithm, are presented. The reduction technique is given for case bases in terms of a measure of the importance of each case to the predictive power of the case base. A trial test is performed on two case bases of different kinds, with several metrics proposed in the solution space. The tests show that GSNN can out-perform standard nearest neighbour methods on this set. Further test results show that a caseremoval order proposed based on a GSNN error function can produce a sparse case base with good predictive power.

Numerical analysis of thermal stresses induced during VFM encapsulant curing

Encapsulant curing using a Variable Frequency Microwave (VFM) system is analysed numerically. Thermosetting polymer encapsulant materials require an input of heat energy to initiate the cure process. In this article, the heating is considered to be performed by a novel microwave system, able to perform the curing process more rapidly than conventional techniques. Thermal stresses are induced when packages containing materials with differing coefficients of thermal expansion are heated, and cure stresses are induced as thermosetting polymer materials shrink during the cure process. These stresses are developed during processing and remain as residual stresses within the component after the manufacturing process is complete. As residual stresses will directly affect the reliability of the device, it is necessary to assess their magnitude and the effect on package reliability. A coupled multiphysics model has been developed to numercially analyse the microwave curing process. In order to obtain a usefully accurate model of this process, a holistic approach has been taken, in which the process is not considered to be a sequence of discrete steps, but as a complex coupled system. An overview of the implemented numerical model is presented, with particular focus paid to analysis of induced thermal stresses. Results showing distribution of stresses within an idealised microelectronics package are presented and discussed.

Mineralogy of selected geological deposits from the United Kingdom and the Republic of Ireland as possible capping materials for low-level radioactive waste disposal facilities

Solid low-level radioactive waste (LLW) is currently being disposed at a number of facilities in the United Kingdom (UK). The safety of these facilities relies to some extent on the use of engineered barriers, such as a cap, to isolate the waste and protect the environment. Generally, the material used as the barrier layer within such a cap should be of low permeability and it should retain this property over long timescales (beyond a few decades normally required for facilities containing non-radioactive wastes). The objective of this research is to determine the mineralogy of selected geological deposits from the UK and Ireland as part of a larger project to examine their suitability as a capping material, particularly on LLW sites. Mineral transformations, as a result of future climate change, may impact on the long-term performance of the cap and even the disposal facility. X-ray diffraction (XRD) was carried-out on the sand, silt and clay fractions of the London Clay, Belfast Upper Boulder Clay, Irish Glacial Till, Belfast Sleech, and Ampthill Clay geological deposits. Minerals were present that could pose both positive and negative effects on the long-term performance of the cap. Smectite, which has a high shrink swell potential, may produce cracks in London Clay, Belfast Upper Boulder Clay and Ampthill Clay capping material during dry, hotter periods as a possible consequence of future climate change; thus, resulting in higher permeability. Ampthill Clay and Belfast Sleech had elevated amounts of organic matter (OM) at 5.93% and 5.88%, respectively, which may also contribute to cracking. Over time, this OM may decompose and result in increased permeability. Gypsum (CaSO4) in the silt and sand fractions of Ampthill Clay may reduce the impact of erosion during wetter periods if it is incorporated into the upper portion of the cap. There are potential negative effects from the acidity created by the weathering of pyrite (FeS2) present in the silt and sand fractions of Belfast Sleech and Ampthill Clay that could impede the growth of grasses used to stabilize the surface of the capping material if this material is used as part of the vegetative soil layer. Additionally, acidic waters generated from pyrite weathering could negatively impact the lower lying capping layers and the disposal facility in general. However, the calcium carbonate (CaCO3) present in the silt and sand fractions of these deposits, and dolomite (CaMg(CO3)2) in Belfast Sleech, may counter act the acidity.

The practice of home in old Cairo: Towards socio-spatial models of sustainable living

The article investigates the practice of home as an everyday system for sustainable living in Old Cairo. The idea of home in this historic urban space has long involved fluid socio-spatial associations and made efficient use of space-activity-time dynamics. As in the past, a individual’s sense of home may here extend beyond or shrink within the physical boundaries of a particular house, as spatial settings are produced and consumed according to time of day, gender association, or special events. The article argues that architects working in this context must understand the dynamics of this complex traditional system if they are to develop locally informed, genuine designs that build on everyday spatial practices. Work by the architect Salah Zaki Said and by the Historic Cities Program of the Aga Khan Trust for Culture is described to illustrate the potential of such engagement, especially as it contrasts to more abstract architectural proposals.

Development and testing of an intermediate temperature glass sealant for use in mixed ionic and electronic conducting membrane reactors

High temperature ceramic membranes have interesting possibilities for application in areas of new and developing technologies such as hydrocarbon combustion with carbon dioxide capture and electrochemical promotion of catalysis (EPOC). However, membrane module sealing remains a significant technical challenge. In this work a borosilicate glass sealant (50SiO₂·25B₂O₃·25Na₂O, mol%) was developed to fit the requirements of sealing an air separation membrane system at intermediate temperatures (300-600 °C). The seal was assessed by testing the leak rates under a range of conditions. The parameters tested included the effect of flowrate on the leak rate, the heating and cooling rates of the reactor and the range of temperatures under which the system could operate. Tests for durability and reliability were also performed. It was found that the most favourable reactor configuration employed a reactor with the ceramic pellet placed underneath the inner chamber alumina tube (inverted configuration), using a quartz wool support to keep the membrane in place prior to sealing. Using this configuration the new glass-based seal was found to be a more suitable sealant than traditional alternatives; it produced lower leak rates at all desirable flowrates, with the potential for rapid heating and cooling and multiple cycling, allowing for prolonged usage. © 2010 Elsevier B.V. All rights reserved.

Whole genome protein microarrays for serum profiling of immunodominant antigens of Bacillus anthracis

A commercial Bacillus anthracis (Anthrax) whole genome protein microarray has been used to identify immunogenic Anthrax proteins (IAP) using sera from groups of donors with (a) confirmed B. anthracis naturally acquired cutaneous infection, (b) confirmed B. anthracis intravenous drug use-acquired infection, (c) occupational exposure in a wool-sorters factory, (d) humans and rabbits vaccinated with the UK Anthrax protein vaccine and compared to naïve unexposed controls. Anti-IAP responses were observed for both IgG and IgA in the challenged groups; however the anti-IAP IgG response was more evident in the vaccinated group and the anti-IAP IgA response more evident in the B. anthracis-infected groups. Infected individuals appeared somewhat suppressed for their general IgG response, compared with other challenged groups. Immunogenic protein antigens were identified in all groups, some of which were shared between groups whilst others were specific for individual groups. The toxin proteins were immunodominant in all vaccinated, infected or other challenged groups. However, a number of other chromosomally-located and plasmid encoded open reading frame proteins were also recognized by infected or exposed groups in comparison to controls. Some of these antigens e.g., BA4182 are not recognized by vaccinated individuals, suggesting that there are proteins more specifically expressed by live Anthrax spores in vivo that are not currently found in the UK licensed Anthrax Vaccine (AVP). These may perhaps be preferentially expressed during infection and represent expression of alternative pathways in the B. anthracis "infectome." These may make highly attractive candidates for diagnostic and vaccine biomarker development as they may be more specifically associated with the infectious phase of the pathogen. A number of B. anthracis small hypothetical protein targets have been synthesized, tested in mouse immunogenicity studies and validated in parallel using human sera from the same study.

Sustained intraocular VEGF neutralization results in retinal neurodegeneration in the Ins2Akita diabetic mouse

Current therapies that target vascular endothelial growth factor (VEGF) have become a mainstream therapy for the management of diabetic macular oedema. The treatment involves monthly repeated intravitreal injections of VEGF inhibitors. VEGF is an important growth factor for many retinal cells, including different types of neurons. In this study, we investigated the adverse effect of multiple intravitreal anti-VEGF injections (200 ng/μl/eye anti-mouse VEGF164, once every 2 weeks totalling 5-6 injections) to retinal neurons in Ins2(Akita) diabetic mice. Funduscopic examination revealed the development of cotton wool spot-like lesions in anti-VEGF treated Ins2(Akita) mice after 5 injections. Histological investigation showed focal swellings of retinal nerve fibres with neurofilament disruption. Furthermore, anti-VEGF-treated Ins2(Akita) mice exhibited impaired electroretinographic responses, characterized by reduced scotopic a- and b-wave and oscillatory potentials. Immunofluorescent staining revealed impairment of photoreceptors, disruptions of synaptic structures and loss of amacrine and retinal ganglion cells in anti-VEGF treated Ins2(Akita) mice. Anti-VEGF-treated WT mice also presented mild amacrine and ganglion cell death, but no overt abnormalities in photoreceptors and synaptic structures. At the vascular level, exacerbated albumin leakage was observed in anti-VEGF injected diabetic mice. Our results suggest that sustained intraocular VEGF neutralization induces retinal neurodegeneration and vascular damage in the diabetic eye.