Microestructura y propiedades mecánicas del material masivo superconductor YBCO a 300 Y 77 K.

En este trabajo se realiza una caracterización mecánica y microestructural del material masivo superconductor YBCO. El material ha sido procesado mediante dos técnicas distintas, Top-Seeding Melt Growth (TSMG) y Bridgman, y este estudio profundiza en el efecto de la microestructura, el método de procesado y la temperatura de ensayo en el comportamiento mecánico de material. Con el fin de conseguir un amplio conocimiento de sus propiedades mecánicas se han realizado ensayos de resistencia a flexión, tenacidad de fractura y dureza Vickers a 300 y 77 K. Asimismo, se llevaron a cabo ensayos de nanoindentación y el tamaño crítico del defecto semielíptico. Los resultados obtenidos muestran que el comportamiento mecánico de los dos materiales está controlado por defectos y grietas, introducidas durante el procesado. También se ha encontrado un buen acuerdo entre el tamaño del defecto critico detectado experimentalmente con los valores obtenidos mediante de análisis de mecánica de fractura.

(Appendix) Oxygen isotope record and carbonate mineralogy of the top part of ODP Hole 101-633A

Hole 633A was drilled in the southern part of Exuma Sound on the toe-of-slope of the southeastern part of Great Bahama Bank during ODP Leg 101. The top 55 m, collected as a suite of six approximately 9.5-m-long hydraulic piston cores, represents a Pliocene-Pleistocene sequence of periplatform carbonate ooze, a mixture of pelagic calcite (foraminifer and coccolith tests), some pelagic aragonite (pteropod tests), and bank-derived fine aragonite and magnesian calcite. A 1.6-m.y.-long hiatus was identified at 43.75 mbsf using calcareous nannofossil biostratigraphy and magnetostratigraphy. The 43.75-m-thick periplatform sequence above the hiatus is a complete late Pliocene-Quaternary record of the past 2.15 m.y. The d18O curve, primarily based on Globigerinoides sacculifera, clearly displays high-frequency/low-amplitude cycles during the early Pleistocene and low-frequency/high-amplitude cycles during the middle and late Pleistocene. Variations in aragonite content in the fine fraction of the periplatform ooze show a cyclic pattern throughout the Pleistocene, as previously observed in piston cores of the upper Pleistocene. These variations correlate well with the d18O record: high aragonite corresponds to light interglacial d18O values, and vice versa. Comparison of the d18O record and the aragonite curve helps to identify 23 interglacial and glacial oxygen-isotope stages, corresponding to 10.5 aragonite cycles (labeled A to K) commonly established during the middle and late Pleistocene (0.9 Ma-present). Strictly based on the aragonite curve, another 11 aragonite cycles, labeled L to V, were identified for the early Pleistocene (0.9 to 1.6 Ma). Mismatches between the d18O record and the aragonite curve occur mainly at some of the glacial-to-interglacial transitions, where aragonite increases usually lag behind d18O depletion. When one visually connects the minima on the Pleistocene aragonite curve, low-frequency (0.4 to 0.5 m.y.) supercycles seem to be superimposed on the high-frequency cycles. The timing of this supercycle roughly matches the timing of the Pleistocene carbonate preservation supercycles described in the Pacific, Indian, and Atlantic oceans. Mismatches between aragonite and d18O cycles are even more obvious for the late Pliocene (1.6 to 2.15 Ma). Irregular aragonite variations are observed for the late Pliocene, although after the onset of late Pleistocene-like glaciations in the North Atlantic Ocean 2.4 m.y. ago the d18O record has shown a mode of high-frequency/low-amplitude cycles. Initiation of climatically induced aragonite cycles occurs only at the Pliocene-Pleistocene transition, 1.6 m.y. ago. After that time, aragonite cycles are fully developed throughout the Quaternary. The 11-m-thick periplatform sequence below the hiatus represents a lower Pliocene interval between 3.75 and 4.45 Ma. The bottom half (4.25-4.45 Ma) has a fairly constant, high aragonite content (averaging 60%) and high sedimentation rates (28 m/m.y.) and corresponds to the end of the prolonged early Pliocene interglacial interval (4.1-5.0 Ma), established as a worldwide high sea-level stand. The second half (3.75-4.25 Ma), in which aragonite content decreases by successive steps, paralleled by a gradual 5180 enrichment in Globigerinoides sacculifera and low sedimentation rates (10 m/m.y), corresponds to the climatic deterioration established worldwide between 4.1 and 3.8 Ma, to a decrease of carbonate preservation observed in the equatorial Pacific Ocean, and to a global sea-level decline. Dolomite, a ubiquitous secondary component in the lower Pliocene, is interpreted as being authigenic and possibly related to diagenetic transformation of primary bank-derived fine magnesian calcite. Transformation of the primary mineralogical composition of the periplatform ooze was evidently minor, as the sediments have retained a detailed record of the Pliocene-Pleistocene climatic evolution. Clear evidence of diagenetic transformations in the periplatform ooze includes (1) the disappearance of magnesian calcite in the upper 20 m of Hole 633A, (2) the occurrence of calcite overgrowths on foraminiferal tests and microclasts at intermittent chalky core levels, and (3) the ubiquitous presence of authigenic dolomite in the lower Pliocene.

Top: Res. of Asa M. Darling, Sec. 12, Augusta Tp. Mich. Bottom: Res. of C.C. Harmon, Sec 18, Augusta Tp. Mich.

Augusta Township (Mich.) residences. Insets: Built 1849. Hop House. Publication information: Chicago, Ill. : Everts & Stewart, 1874.

On the absolute calibration of bench-top small-angle X-ray scattering instruments: a comparison of different standard methods

Absolute calibration relates the measured (arbitrary) intensity to the differential scattering cross section of the sample, which contains all of the quantitative information specific to the material. The importance of absolute calibration in small-angle scattering experiments has long been recognized. This work details the absolute calibration procedure of a small-angle X-ray scattering instrument from Bruker AXS. The absolute calibration presented here was achieved by using a number of different types of primary and secondary standards. The samples were: a glassy carbon specimen, which had been independently calibrated from neutron radiation; a range of pure liquids, which can be used as primary standards as their differential scattering cross section is directly related to their isothermal compressibility; and a suspension of monodisperse silica particles for which the differential scattering cross section is obtained from Porod's law. Good agreement was obtained between the different standard samples, provided that care was taken to obtain significant signal averaging and all sources of background scattering were accounted for. The specimen best suited for routine calibration was the glassy carbon sample, due to its relatively intense scattering and stability over time; however, initial calibration from a primary source is necessary. Pure liquids can be used as primary calibration standards, but the measurements take significantly longer and are, therefore, less suited for frequent use.