UV optical absorption spectra analysis of beryl crystals from Brazil

The spectral decomposition analysis was applied to the optical absorption spectra of green and colorless beryl crystals from the Brazilian Eastern Pegmatitic province in the natural state, Submitted to heat treatment and irradiated with UV light The attributions of the lines were made taking into account highly accurate quantum mechanical calculations The deconvolution of the green beryl spectra revealed four lines, two of them around 12,000 cm(-1) (1 5eV) and two of them around 34,000 cm(-1) (4.2 eV) attributed to Fe(2+) and Fe(3+), respectively The deconvolution of the colorless beryl spectra without any treatment, after heating and for the same heat treatment followed by UV light irradiation revealed five lines The analysis of ratio relations showed that the lines at 36,400 cm(-1) (4.5 eV) and 41,400 cm(-1) (5 1 eV) belongs to a single defect attributed to a silicon dangling bond defect (=Si). Discussions and comparison with reported defects in quartz have supported the allocation of the lines at 61,000 cm(-1) (7.6 eV) and 43,800 cm(-1) (5 4 eV) to diamagnetic oxygen vacancy defect ( Si-Si ) and unrelaxed ( Si Si ) defect, respectively Finally, the line at 39.100 cm(-1) (4.8 eV), quite polarized along the c-axis, was attributed to a (Fe(2+) OH(-)) defect in the structural channels (C) 2009 Elsevier B V All rights reserved

Thin films of xyloglucans for BSA adsorption

In this work. XG extracted from Tamarindus indica (XGT) and Copaifera langsdorffii (XGC) seeds were deposited onto Si wafers as thin films. The characteristics of XGT and XGC adsorbed layers were compared with a commercial XG sample (TKP, Tamarind kernel powder) by ellipsometry, and atomic force microscopy (AFM). Moreover, the adsorption of oxidized derivative of XGT (To60) onto amino-terminated Si wafers and the immobilization of bovine serum albumin (BSA) onto polysaccharides covered wafers, as a function of pH, were also investigated. The XG samples presented molar ratios Glc:Xyl:Gal of 2.4:2.1:1 (XGC) 2.8: 23: 1 (XGT) and 1.91.91 (TKP). The structure of XGT and XGC was determined by O-methy alditol acetate derivatization and showed similar features, but XGC confirmed the presence of more alpha-D-Xyl branches due to more beta-D-Gal ends. XGT deposited onto Si adsorbed as fibers and small entities uniformly distributed, as evidenced by AFM, while TPK and XGC formed larger aggregates. The thickness of To60 onto amino-terminated surface was similar to that determined for XGT onto Si wafers. A maximum in the adsorbed amount of BSA occurred close to its isoelectric point (5.5). These findings indicate that XGT and To60 are potential materials for the development of biomaterials and biotechnological devices. (C) 2008 Elsevier B.V. All rights reserved.

Isquemia silenciosa e arritmias ventriculares são preditores independentes de evenos no pós-infarto do miocárdio de baixo risco

pós-infarto agudo do miocárdio (IAM) têm mostrado baixo valor preditivo positivo quando estudados isoladamente. A possibilidade da Eletrocardiografia Dinâmica de 24 horas (ECGD) fornecer dados referentes a isquemia silenciosa (IS), arritmias ventriculares e modulação autonômica do coração pelo estudo da variabilidade da freqüência cardíaca (VFC), levou o autor a empregar este método em pacientes acometidos de IAM com o objetivo de avaliar se estas três variáveis estariam relacionadas a presença de eventos desfavoráveis em evolução a médio prazo. Material e Métodos – Foram selecionados 91 pacientes acometidos de um primeiro IAM não-complicado e realizados exames de ECGD de 24 h por dois dias consecutivos, antes da alta hospitalar. Os parâmetros pesquisados nos exames foram: isquemia silenciosa, identificação e quantificação de arritmias ventriculares e determinação dos índices de VFC pelos métodos do domínio do tempo e do mapa de retorno tridimensional. Foram considerados como desfechos: re-infarto, angina instável, taquicardia ventricular sustentada e morte. Resultados – No seguimento médio de 27,7 meses (DP=15,45), 23 (25%) dos pacientes apresentaram eventos, sendo nove fatais. Os eventos foram mais freqüentes entre os pacientes que apresentaram extra-sístoles ventriculares ≥10/hora (p=0,01) e também naqueles com IS (p=0,02). Em modelo de análise multifatorial, a presença de dislipidemia elevou o valor preditivo positivo dessas variáveis. Nenhum dos índices de VFC esteve significativamente relacionado ao surgimento de eventos. Conclusões – Em pacientes pós-IAM de baixo risco, a presença de arritmias ventriculares freqüentes ou de isquemia silenciosa está relacionada a um prognóstico desfavorável. O estudo da VFC não mostrou utilidade na estratificação de risco destes pacientes.

Continuous infusion of ketamine in hypovolemic dogs anesthetized with desflurane

Objective: To evaluate the cardiorespiratory effects of continuous infusion of ketamine in hypovolemic dogs anesthetized with desflurane.Design: A prospective experimental study.Animals: Twelve mixed breed dogs allocated into 2 groups: saline (n=6) and ketamine (n=6).Interventions: After obtaining baseline measurements (time [T] 0) in awake dogs, hypovolemia was induced by the removal of 40 mL of blood/kg over 30 minutes. Anesthesia was induced and maintained with desflurane (1.5 minimal alveolar concentration) and 30 minutes later (T75) a continuous intravenous (IV) infusion of saline or ketamine (100 mu g/kg/min) was initiated. Cardiorespiratory evaluations were obtained 15 minutes after hemorrhage (T45), 30 minutes after desflurane anesthesia, and immediately before initiating the infusion (T75), and 5 (T80), 15 (T90), 30 (T105) and 45 (T120) minutes after beginning the infusion.Measurements and main results: Hypovolemia (T45) reduced the arterial blood pressures (systolic arterial pressure, diastolic arterial pressure [DAP] and mean arterial pressure [MAP]), cardiac (CI) and systolic (SI) indexes, and mean pulmonary arterial pressure (PAP) in both groups. After 30 minutes of desflurane anesthesia (T75), an additional decrease of MAP in both groups was observed, heart rate was higher than T0 at T75, T80, T90 and T105 in saline-treated dogs only, and the CI was higher in the ketamine group than in the saline group at T75. Five minutes after starting the infusion (T80), respiratory rate (RR) was lower and the end-tidal CO(2) (ETCO(2)) was higher compared with values at T45 in ketamine-treated dogs. Mean values of ETCO(2) were higher in ketamine than in saline dogs between T75 and T120. The systemic vascular resistance index (SVRI) was decreased between T80 and T120 in ketamine when compared with T45.Conclusions: Continuous IV infusion of ketamine in hypovolemic dogs anesthetized with desflurane induced an increase in ETCO(2), but other cardiorespiratory alterations did not differ from those observed when the same concentration of desflurane was used as the sole anesthetic agent. However, this study did not evaluate the effectiveness of ketamine infusion in reducing desflurane dose requirements in hypovolemic dogs or the cardiorespiratory effects of ketamine-desflurane balanced anesthesia.

Correlação entre medidas paramétricas e não-paramétricas de estabilidade em soja

Foram avaliadas a adaptabilidade e a estabilidade de genótipos de soja (Glycine max L.) segundo a metodologia clássica de Eberhart e Russell e a estabilidade dos mesmos genótipos pela metodologia não-paramétrica de Huhn. Os experimentos foram conduzidos no delineamento em blocos casualizados, com três repetições e com 30 tratamentos (genótipos de soja), durante três anos consecutivos. As parcelas experimentais foram constituídas por quatro linhas de cultivo, espaçadas de 0,50 m e com densidade de 25 plantas por metro linear. Como área útil, foram tomadas as linhas centrais, eliminando-se 0,5 m de cada extremidade. A comparação entre as metodologias foi efetuada considerando-se o caráter produção de grãos. Verificou-se correlação de posição significativa dos postos dos genótipos, entre o desvio da regressão e as duas medidas não-paramétricas de estabilidade, porém o mesmo não foi observado entre o coeficiente de regressão e as medidas não-paramétricas (Si(1) e Si(2)). As medidas Si(1) e Si(2) mostraram-se quase que perfeitamente correlacionadas.

Aplicações de Dispositivos de Microondas utilizando Substrato EBG/PBG para Comunicações Móveis

The modern society depends on an efficient communications system able to of transmitting and receiving information with a higher speed and reliability every time. The need for ever more efficient devices raises optimization techniques of microstrip devices, such as techniques to increase bandwidth: thicker substrates and substrate structures with EBG (Electromagnetic Band Gap) and PBG (Photonic Band Gap). This work has how aims the study of the application of PBG materials on substrates of planar structures in microstrip, more precisely in directional quadrature couplers and in rat-race and impedance of transformers. A study of the planar structures in microstrip and substrates EBG is presented. The PBG substrates can be used to optimize the radiation through the air, thus reducing the occurrence of surface waves and the resulting diffraction edge responsible for degradation of radiation pattern. Through specific programs in FORTRAN Power Station obtained the frequencies and couplings for each structure. Are used the program PACMO - Computer Aided Design in Microwave. Results are obtained of the frequency and coupling devices, ranging the frequency band used (cellular communication and Wimax systems) and the permittivity of the substrate, comparing the results of conventional material and PBG materials in the s and p polarizations.

Metodologia de análise e diagnóstico de fratura em um componente automotivo sujeito a cargas cíclicas alternadas

The competitiveness of the trade generated by the higher availability of products with lower quality and cost promoted a new reality of industrial production with small clearances. Track deviations at the production are not discarded, uncertainties can statistically occur. The world consumer and the Brazilian one are supported by the consumer protection code, in lawsuits against the products poor quality. An automobile is composed of various systems and thousands of constituent parts, increasing the likelihood of failure. The dynamic and security systems are critical in relation to the consequences of possible failures. The investigation of the failure gives us the possibility of learning and contributing to various improvements. Our main purpose in this work is to develop a systematic, specific methodology by investigating the root cause of the flaw occurred on an axle end of the front suspension of an automobile, and to perform comparative data analyses between the fractured part and the project information. Our research was based on a flaw generated in an automotive suspension system involved in a mechanical judicial cause, resulting in property and personal damages. In the investigations concerning the analysis of mechanical flaws, knowledge on materials engineering plays a crucial role in the process, since it enables applying techniques for characterizing materials, relating the technical attributes required from a respective part with its structure of manufacturing material, thus providing a greater scientific contribution to the work. The specific methodology developed follows its own flowchart. In the early phase, the data in the records and information on the involved ones were collected. The following laboratory analyses were performed: macrography of the fracture, micrography with SEM (Scanning Electron Microscope) of the initial and final fracture, phase analysis with optical microscopy, Brinell hardness and Vickers microhardness analyses, quantitative and qualitative chemical analysis, by using X-ray fluorescence and optical spectroscopy for carbon analysis, qualitative study on the state of tension was done. Field data were also collected. In the analyses data of the values resulting from the fractured stock parts and the design values were compared. After the investigation, one concluded that: the developed methodology systematized the investigation and enabled crossing data, thus minimizing diagnostic error probability, the morphology of the fracture indicates failure by the fatigue mechanism in a geometrically propitious location, a tension hub, the part was subjected to low tensions by the sectional area of the final fracture, the manufacturing material of the fractured part has low ductility, the component fractured in an earlier moment than the one recommended by the manufacturer, the percentages of C, Si, Mn and Cr of the fractured part present values which differ from the design ones, the hardness value of the superior limit of the fractured part is higher than that of the design, and there is no manufacturing uniformity between stock and fractured part. The work will contribute to optimizing the guidance of the actions in a mechanical engineering judicial expertise

Mecanismos de desgaste, história térmica e ciclo de vida de componentes de um motor de combustão interna de aeromodelo

We developed an assay methodology that considered the temperature variation and the scanning electron microscopy as a method to quantify and characterize respectively the consumption evolution in three 46 LA machines, with internal combustion and two-stroke engines, 7.64 cm3 cylinder capacity, 23.0 millimeters diameter and 18.4 millimeters course, RPM service from 2.000 to 16.000 rpm, 1.2 HP power, and 272 grams weight. The investigated engines components were: (1) head of the engine (Al-Si alloy), (2) piston (Al-Si alloy) and (3) piston pin (AISI 52100 steel). The assays were carried out on a desktop; engines 1 and 2 were assayed with no load, whereas in two assays of engine 3 we added a fan with wind speed that varied from 8.10 m/s to 11.92 m/s, in order to identify and compare the engine dynamic behavior as related to the engines assayed with no load. The temperatures of the engine s surface and surroundings were measured by two type K thermopairs connected to the assay device and registered in a microcomputer with data recording and parameters control and monitoring software, throughout the assays. The consumed surface of the components was analyzed by scanning electron microscopy (SEM) and microanalysis-EDS. The study was complemented with shape deformation and mass measurement assays. The temperature variation was associated with the oxides morphology and the consumption mechanisms were discussed based on the relation between the thermal mechanical effects and the responses of the materials characterization

Teores de silício no solo e na planta de arroz de terras altas com diferentes doses de adubação silicatada e nitrogenada

O Si não é elemento essencial para o crescimento e desenvolvimento das plantas, porém sua absorção pode trazer inúmeros benefícios para culturas acumuladoras de Si, como o arroz. Entretanto, considerando o avançado grau de intemperização em que se encontram os solos tropicais, os teores de Si disponível nestes solos são baixos. O objetivo deste trabalho foi avaliar, na cultura do arroz de terras altas sob condições de túnel plástico, o efeito de doses de Si e de N na produção de matéria seca, na produtividade de grãos, no teor de N, nos teores de Si no solo e na planta e na quantidade de Si extraído do solo. Os tratamentos foram constituídos por três doses de N (5, 75 e 150 mg kg-1 de N), tendo como fonte a uréia e quatro doses de Si (0, 200, 400 e 600 mg kg-1 de SiO2) tendo como fonte o silicato de cálcio (Wollastonita). O delineamento experimental utilizado foi inteiramente casualizado com esquema fatorial 3 x 4, com cinco repetições. O acúmulo de matéria seca, a produtividade de grãos e os teores de N na planta não foram influenciados pelas doses de Si. O incremento da adubação nitrogenada aumentou a produção de matéria seca, a produtividade de grãos e o teor de N na planta, porém nenhum efeito foi encontrado para os teores de Si no solo. Houve interação N x Si para os teores de Si na planta e para a quantidade de Si acumulado pelas plantas.

Lesões desportivas na elite do atletismo brasileiro: estudo a partir de morbidade referida

Os processos de quantificação e associação das lesões do esporte aos seus possíveis fatores causais são importantes para melhor entendimento sobre assunto. Assim constituiu-se como objetivo do presente estudo a observação das lesões desportivas (LD) em atletas da elite brasileira do atletismo, associando-as aos seus mecanismos de instalação e características da modalidade. Foram entrevistados 86 atletas (47 homens e 39 mulheres) convocados para representar o Brasil durante o ano de 2003. Utilizou-se um inquérito de morbidade referida, validado anteriormente, para obtenção dos dados referentes aos atletas e suas lesões. Para a análise dos resultados adotou-se o teste de Goodman para contrastes entre e dentro de proporções binomiais, sendo todas as conclusões discutidas para 5% de significância estatística. Os resultados mostraram que há maior taxa de lesão por atleta (l/a), nas provas combinadas (3,5 l/a), seguidas por eventos de velocidade (2,6 l/a), resistência (1,9 l/a) e saltos (1,9 l/a) respectivamente. O principal mecanismo causal é a alta intensidade acometendo preferencialmente velocistas e fundistas. Outra forte associação foi observada entre lesões musculares e provas de velocidade, que também apresentam preferência para ocorrência de lesão na região da coxa. As atividades com elevada intensidade foram o principal responsável por lesões musculares, enquanto as osteoarticulares e tendinopatias ocorrem com excesso de repetições. Concluiu-se, a partir dos achados, que existem associações entre lesões e fatores causais, como entre provas e lesões, mecanismos de lesão e local anatômico.

Sistemas Nanoestruturados: Heteroestruturas Quasi-Periódicas de Nitretos e Cálculos Ab initio em Polimorfos CaCO3

The physical properties and the excitations spectrum in oxides and semiconductors materials are presented in this work, whose the first part presents a study on the confinement of optical phonons in artificial systems based on III-V nitrides, grown in periodic and quasiperiodic forms. The second part of this work describes the Ab initio calculations which were carried out to obtain the optoeletronic properties of Calcium Oxide (CaO) and Calcium Carbonate (CaCO3) crystals. For periodic and quasi-periodic superlattices, we present some dynamical properties related to confined optical phonons (bulk and surface), obtained through simple theories, such as the dielectric continuous model, and using techniques such as the transfer-matrix method. The localization character of confined optical phonon modes, the magnitude of the bands in the spectrum and the power laws of these structures are presented as functions of the generation number of sequence. The ab initio calculations have been carried out using the CASTEP software (Cambridge Total Sequential Energy Package), and they were based on ultrasoft-like pseudopotentials and Density Functional Theory (DFT). Two di®erent geometry optimizations have been e®ectuated for CaO crystals and CaCO3 polymorphs, according to LDA (local density approximation) and GGA (generalized gradient approximation) approaches, determining several properties, e. g. lattice parameters, bond length, electrons density, energy band structures, electrons density of states, e®ective masses and optical properties, such as dielectric constant, absorption, re°ectivity, conductivity and refractive index. Those results were employed to investigate the confinement of excitons in spherical Si@CaCO3 and CaCO3@SiO2 quantum dots and in calcium carbonate nanoparticles, and were also employed in investigations of the photoluminescence spectra of CaCO3 crystal

Hexagonal mesoporous silica modified with 2-mercaptothiazoline for removing mercury from water solution

A method for the attachment of 2-mercaptothiazoline (MTZ) to modified silica gel has been developed. In the first step, a new silylant agent was synthesized, named SiMTZ, by the reaction between MTZ molecule and chloropropyltrimethoxysilane (SiCl). SiMTZ and tetraethylortosilicate were co-condensed in the presence of n-dodecylamine, a neutral surfactant template, to produce a modified ordered hexagonal mesoporous silica named HMTZ. The modified material contained 0.89 +/- 0.03 mmol of 2-mercaptothiazoline per gram of silica. FT-IR, FT-Raman, Si-29- and C-13-NMR spectra were in agreement with the proposed structure of the modified mesoporous silica in the solid state. HMTZ material has been used for divalent mercury adsorption from aqueous solution at 298 I K. The series of adsorption isotherms were adjusted to a modified Langmuir equation. The maximum number of moles of mercury adsorbed gave 2.34 +/- 0.09 mmol/g of material. The same interaction was followed by calorimetric titration on an isoperibol calorimeter. The HMTZ presented a high capacity for the removal of the contaminant mercury from water. The Delta H and Delta G values for the interaction were determined to be -56.34 +/- 1.07 and -2.14 +/- 0.11 kJ mol(-1). This interaction process was accompanied by a decrease of entropy value (- 182 J mol(-1) K-1). Thus, the interaction between mercury and HMTZ resulted in a spontaneous thermodynamic system with a high favorable exothermic enthalpic effect. (c) 2007 Elsevier B.V. All rights reserved.

Análise química de produtos de incrustação em dutos de petróleo por espectometria de fluorescência de raios X

The quantitative chemical characterization of the inorganic fraction of scale products is very relevant in studying, monitoring and controlling corrosive processes of oil pipelines. The X-ray fluorescence spectrometry (XRF) is a very versatile analytical technique, which can be used in quantitative analysis in solid samples at low concentrations of the chemical element, in the order of few ppm. A methodology that involves sample preparation diluted in the proportion of 1:7 (one portion of the sample for seven of wax), pressed as pellets was used in the XRF calibration for chemical analysis of scale products from oil pipelines. The calibration involved the preparation of reference samples from mixtures of P.A. reagents, aiming to optimize the time consumed in the steps of sample preparation and analysis of Al, Ba, Ca, Fe, K, Mg, Mn, Na, P, S, Si, Sr and Ti, using the same pressed pellet for trace and major elements analysis

Study on soluble heavy metals with preconcentration by using a new modified oligosilsesquioxane sorbent

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

An Oligosilsesquioxane Cage Functionalized with Molybdenum(II) Organometallic Fragments

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)