THERMAL-ANALYSIS OF POLYARYLENE ETHER SULFONES AND POLYIMIDES

Some results on the thermal analysis of polyimides and polyaryl ether sulfones, some reactions and the purity determination of the monomers, and the thermal stability and kinetic analysis of the thermo-oxidative degradation of these polymers are described.

WATER-SOLUBLE AND AMPHIPHILIC POLYMERS .6. A STUDY ON THE SURFACE-COMPOSITION OF CAST FILMS OF PST/PMAA AND PEO-PST-PEO BLOCK POLYMERS BY XPS

Thin films of PSt/PMAA and PEO-PSt-PEO block polymers were deposited on a polystyrene substrate by solution adsorption (with or without solvent treatment), and the film surfaces were characterized by means of XPS. Direct solvent - casting of PEO-PSt-PEO from benzene solutions resulted in PSt-rich surfaces, whereas PMAA richer surfaces were obtained for PSt/PMAA films cast from DMF solutions. Moreover, solvent treatment after casting had profound effect on the film surface composition. Treatment with water markedly increased the surface concentration of polar PEO segments. In the case of PSt-PMAA block polymers, the PSt content on the surface increased in the order of water < ethanol < cyclohexane < petroleum ether, the last-named giving films with almost pure PSt surface. It is well worth noticing that the bulk composition had little to do with the surface composition for both PSt/PMAA and PEO-PSt-PEO block polymers within the composition range investigated when subsequent solvent treatment was applied.

WATER-SOLUBLE AND AMPHIPHILIC POLYMERS .7. SYNTHESIS AND CHARACTERIZATION OF A NOVEL COMB-TYPE AMPHIPHILIC POLYMER PAMC16S

A novel comb-like amphiphilic polymer, poly (2-acrylamidohexadecylsulfonic acid) (PAMC16S), was synthesized by free radical polymerization of the corresponding amphiphilic monomer in 1,4-dioxane-water mixed solvents. Depending on the ratio of water/dioxane in the solvent, the reaction proceeded by either precipitation polymerization or micellar polymerization. The molecular weight of the polymer obtained under similar conditions decreased and subsequently increased with the increase of water content in the mixed solvent. The polyion nature of PAMC16S was confirmed by viscosity data of ethanolic solutions. In addition, the polymer was characterized by solubility, IR, TG and wide angle X-ray diffraction methods.

SOLUBLE POLY-(O,M)-TOLUIDINE

The soluble poly-o-toluidine (POT) and poly-m-toluidine (PMT) have been success- fully prepared under controlled conditions of polymerization and post-treatment, and characterized by IR, VPO and elemental analysis. It is found that the soluble and insol- uble polymers obtained with two different methods (Ⅰ and Ⅱ) have the similar conduc- tivity and molecular chain structure. VPO measurement shows that the number average molecular weight (Mn) of soluble polymers is about 3000. The mole ratio o...

Highly soluble and stable recombinant holo-phycocyanin alpha subunit expressed in Escherichia coli

C-phycocyanin (Cpc) is one of the phycobiliproteins with highly fluorescent and various pharmacological activities Holo-Cpc-alpha Subunit (holo-CpcA) expressed in Escherichia colt resulted in low yield and tended to aggregate after purification in this Study, we constructed a new plasmid coding holo-CpcA fused with hexahistidine and maltose-binding protein tag, which designated as HMCpcA. to Improve Its Solubility and stability without the Impairment of its spectra anti fluorescent properties HMCpcA was significantly more stable over time and a wider range of pH as compared to holo-CpcA. In addition. both the solubility and yields of HMCpcA increase significantly We here provided an example to demonstrate that MBP could also Improve the stability of the protein it fused while it has been reported as a soluble fusion partner before. This novel fluorescent protein will facilitate the large-scale production and be potentially applicable for the development Of fluorescent probes, as well as antioxidant agents (C) 2009 Elsevier B V. All rights reserved

A remarkable synergic effect of water-soluble bimetallic catalyst in the hydrogenation of aromatic nitrocompounds

Hydrogenation of nitrobenzene can be catalyzed by the water-soluble catalyst PdCl2(TPPTS)(2) (TPPTS = tris(m-sulfonatophenyl)phosphine trisodium salt) under normal pressure at 65 degrees C in H2O/toluene biphasic solvent system. The exhibits higher catalytic activity and selectivity for the hydrogenation of aromatic nitrocompounds, compared with PdCl2(TPPTS)(2) or H2PtCl6 alone. The transmission electron micrographs demonstrate that the monometallic catalyst is composed of ultrafine palladium particles of almost uniform size while the particles of bimetallic catalyst are more widely distributed in size than those of the monometallic ones. (C) 1999 Elsevier Science B.V. All rights reserved.