Estudo da turvação em rede de abastecimento de água a alta pressão no grande porto

A turvação é uma das principais preocupações das empresas de rede de distribuição de água potável. Para se saber a sua origem existem diversos mecanismos, sugeridos em bibliografia, que explicam a formação de depósitos de partículas nas tubagens, que se acumulam em camadas sobrepostas, criando entre si forças de coesão. A turvação pode surgir se o caudal ou a velocidade na tubagem aumentar, por alguma razão, pois um aumento da tensão de corte sobre o depósito, pode superar as forças de coesão levando à sua ressuspensão. Esta explicação é traduzida matematicamente pelo modelo PODDS (Prediction of Discolouration in Drinking Water Distribtuion System). O modelo PODDS foi compilado em EPANET recentemente por uma equipa de investigadores da Universidade de Sheffield e foi utilizado para fazer o estudo num ramal da empresa AdDP - Águas do Douro e Paiva, SA. Os resultados das simulações permitirão prever o caudal mínimo teórico a utilizar no ramal que origina o valor limite de turvação. Foram realizados ensaios de variação do caudal no ramal de Jovim-Ramalde para a calibração do modelo. Os parâmetros obtidos foram: Cmáx igual a 100 NTUm, b e n igual a 1, k é igual -1 NTUm3/N, e por fim, P igual a 0,0001 NTUm3/N.s. Após calibração do modelo realizaram-se simulações com atualização das forças de coesão para conhecer o caudal que provocaria a mobilização das partículas até uma turvação de 4 NTU e concluiu-se que o valor seria de 4,32 m3/s. O tempo necessário para regressar a valores inferiores a 1 NTU também foi determinado e 4 horas e 8 minutos foi o valor alcançado. Por fim realizou-se um estudo da influência da temperatura neste modelo e o resultado mostrou que este parâmetro é pouco influente para a gama de temperaturas considerada.

Filamentous fungi occurrence in free water and biofilms from drinking water storage tanks

In some regions of Brazil, especially where the water is scarce, drinking water is stored in water storage tanks. This practice gives the consumer the guarantee of available water. The water storage conditions such as the exposure to hot weather when the tanks are on rooftops allow the development of microorganisms and microbial biofilms which can deteriorate the water quality and increase the risk to human health [1,2]. This study describes the filamentous fungi (FF) detected in free water and biofilms in drinking water storage tanks in Recife - Pernambuco, Brazil. Five sampling times in triplicate were performed at two distinct points. Colony-forming units (CFU) of FF fungi were determined with 0.45 μm filtration membranes using peptone glucose rose Bengal agar (PGRBA). From the 30 samples analysed a total of 1136 CFU were obtained. The water biofilms were collected from samplers consisting of polyethylene coupons, previously installed in the reservoirs. These coupons were transferred to PGRBA plates and incubated using with the same conditions described for free FF. For the in situ detection of FF in biofilms the Calcofluor White staining technique was used. This procedure demonstrated FF forming biofilms on the surfaces of the coupons. Brazilian legislation does not define limits for FF in drinking water. However considering the potential risk of fungal contamination, the data obtained in this study will contribute to developing future quantitative and qualitative parameters for the presence of fungi in drinking water distribution systems in Brazil.

The effects of sodium hypochlorite against selected drinking water-isolated bacteria in planktonic and sessile states

Chlorine is the most commonly used agent for general disinfection, particularly for microbial growth control in drinking water distribution systems. The goals of this study were to understand the effects of chlorine, as sodium hypochlorite (NaOCl), on bacterial membrane physicochemical properties (surface charge, surface tension and hydrophobicity) and on motility of two emerging pathogens isolated from drinking water, Acinetobacter calcoaceticus and Stenotrophomonas maltophilia. The effects of NaOCl on the control of single and dual-species monolayer adhered bacteria (2 h incubation) and biofilms (24 h incubation) was also assessed. NaOCl caused significant changes on the surface hydrophobicity and motility of A. calcoaceticus, but not of S. maltophilia. Planktonic and sessile S. maltophilia were significantly more resistant to NaOCl than A. calcoaceticus. Monolayer adhered co-cultures of A. calcoaceticus-S. maltophilia were more resilient than the single species. Oppositely, dual species biofilms were more susceptible to NaOCl than their single species counterparts. In general, biofilm removal and killing demonstrated to be distinct phenomena: total bacterial viability reduction was achieved even if NaOCl at the higher concentrations had a reduced removal efficacy, allowing biofilm reseed. In conclusion, understanding the antimicrobial susceptibility of microorganisms to NaOCl can contribute to the design of effective biofilm control strategies targeting key microorganisms, such as S. maltophilia, and guarantying safe and high-quality drinking water. Moreover, the results reinforce that biofilms should be regarded as chronic contaminants of drinking water distribution systems and accurate methods are needed to quantify their presence as well as strategies complementary/alternative to NaOCl are required to effectively control the microbiological quality of drinking water.

Free-living amoebae: Biological by-passes in water treatment.

Free-living amoebae constitute reservoirs for many bacteria including not only well-known pathogens but also emerging pathogens responsible for respiratory diseases, and contribute to the protection, survival and dissemination of these bacteria in water systems, despite the application of disinfection or thermal treatments. In this article we review the available information on the presence of free-living amoebae and amoebae-resisting bacteria in drinking water systems, on the factors that contribute to their presence in the water and/or the biofilms, on the possible control measures and their effectiveness, and we identify some gaps in current knowledge needing further research.

A hybrid method for sag source location in power network

The work presented in this paper belongs to the power quality knowledge area and deals with the voltage sags in power transmission and distribution systems. Propagating throughout the power network, voltage sags can cause plenty of problems for domestic and industrial loads that can financially cost a lot. To impose penalties to responsible party and to improve monitoring and mitigation strategies, sags must be located in the power network. With such a worthwhile objective, this paper comes up with a new method for associating a sag waveform with its origin in transmission and distribution networks. It solves this problem through developing hybrid methods which hire multiway principal component analysis (MPCA) as a dimension reduction tool. MPCA reexpresses sag waveforms in a new subspace just in a few scores. We train some well-known classifiers with these scores and exploit them for classification of future sags. The capabilities of the proposed method for dimension reduction and classification are examined using the real data gathered from three substations in Catalonia, Spain. The obtained classification rates certify the goodness and powerfulness of the developed hybrid methods as brand-new tools for sag classification

Interchange of callosal and association projections in the developing visual cortex.

Neurons projecting transitorily into the corpus callosum from area 17 of the cat were retrogradely labeled by the fluorescent tracer Fast Blue (FB) injected into contralateral areas 17 and 18 on postnatal days 1-5. During the second postnatal month these neurons were still labeled by the early injection, although they had eliminated their callosal axon. At this time, 15-20% of these neurons could be retrogradely relabeled by injections of Diamidino Yellow (DY) into ipsilateral areas 17 and 18, but few or none by similar injections in the other areas that receive from area 17 (19, 21a, PMLS, 20a, 20b, DLS). Similarly, area 17 neurons projecting transitorily to contralateral area PMLS during the first postnatal week could be relabeled by DY injections in ipsilateral areas 17 and 18 but not in PMLS. Already around birth, many transitorily callosal neurons in area 17 send bifurcating axons both to contralateral areas 17 and 18 and ipsilateral area 18. It is probable that during postnatal development some of these neurons selectively eliminate their callosal axon collaterals and maintain the projection to ipsilateral area 18. In fact, some transitorily callosal neurons in area 17 can be double-labeled by simultaneous perinatal injections of FB in contralateral areas 17 and 18 and of a new long-lasting retrograde tracer, rhodamine-conjugated latex microspheres, in ipsilateral area 18. The same neurons can then be relabeled by reinjecting ipsilateral area 18 with DY during the second postnatal month. This finding, however, does not exclude the possibility that some transitorily callosal neurons send an axon to ipsilateral area 18 after eliminating their callosal axon. In conclusion, area 17 neurons that project transitorily through the corpus callosum later participate, probably permanently, in ipsilateral corticocortical projections but selectively to areas 17-18. The mechanism responsible for this selectivity is unknown, but it may be related to the differential radial distribution (i.e., to birth date) of area 17 neurons engaged in the various corticocortical projections. The problems raised by the use of long-lasting retrograde fluorescent tracers in neurodevelopmental studies and by the quantification of results of double- and triple-labeling paradigms are also discussed.

Nuclear pairing: surface or bulk?

We analyze how the spatial localization properties of pairing correlations are changing in a major neutron shell of heavy nuclei. It is shown that the radial distribution of the pairing density depends strongly on whether the chemical potential is close to a low or a high angular momentum level and has little sensitivity to whether the pairing force acts at the surface or in the bulk. The pairing density averaged over one major shell is, however, rather flat, exhibiting little dependence on the pairing force. Hartree-Fock-Bogoliubov calculations for the isotopic chain 100-132Sn are presented for demonstration purposes.

Ground-state properties of a dilute homogeneous Bose gas of hard disks in two dimensions

The energy and structure of a dilute hard-disks Bose gas are studied in the framework of a variational many-body approach based on a Jastrow correlated ground-state wave function. The asymptotic behaviors of the radial distribution function and the one-body density matrix are analyzed after solving the Euler equation obtained by a free minimization of the hypernetted chain energy functional. Our results show important deviations from those of the available low density expansions, already at gas parameter values x~0.001 . The condensate fraction in 2D is also computed and found generally lower than the 3D one at the same x.

Neutron diffraction analysis on FINEMET alloys

Neutron diffraction has been used to study in situ the nanocrystallization process of Fe73.5Cu1Nb3Si22.5-xBx (x = 5, 9, and 12) amorphous alloys. Nanocrystallization results in a decrease of both the silicon content and the grain size of the Fe(Si) phase with increasing value of x. By comparing the radial distribution function peak areas with those predicted for ideal bcc and DO3 structure, it can be concluded that the ordering in DO3 Fe(Si) crystals increases with the silicon content.

Estudi comparatiu: errors de les infermeres en la preparació i l'administració de la medicació segons dos sistemes de distribució

Introducció: Els errors de medicació són definits com qualsevol incident prevenible que pot causar dany al pacient o donar lloc a una utilització inapropiada dels medicaments, quan aquests estan sota el control dels professionals sanitaris o del pacient. Els errors en la preparació i l’administració de medicació són els més comuns de l’àrea hospitalària i, tot i la llarga cadena per la qual passa el fàrmac, el professional d’infermeria és el últim responsable de l’acció, tenint així, un paper molt important en la seguretat del pacient. Les infermeres dediquen el 40% del temps de la seva jornada laboral en tasques relacionades amb la medicació. Objectiu: Determinar si les infermeres produeixen més errors si treballen amb sistemes de distribució de medicació de stock o en sistemes de distribució unidosis de medicació. Metodologia: Estudi quantitatiu, observacional i descriptiu, on la notificació d’errors (o oportunitats d’error) realitzats per la infermera, en les fases de preparació i administració de medicació, es farà mitjançant un qüestionari autoelaborat. Els elements a identificar seran: el tipus d’error, les causes que poden haver--‐lo produït, la seva potencial gravetat i qui l’ha pogut evitar; així com el tipus de professional que l’ha produït. Altres dades rellevants són: el medicament implicat junt amb la dosis i la via d’administració i el sistema de distribució utilitzat. Mostreig i mostra: El mostreig serà no probabilístic i per conveniència. S’escolliran aquelles infermeres que l’investigador consideri amb les característiques necessàries per participar en l’estudi, així que la mostra estarà formada per les infermeres les quals treballen a la unitat 40 de l’Hospital del Mar i utilitzen un sistema de distribució de medicació de dosis unitàries i les infermeres que treballen a urgències (concretament a l’àrea de nivell dos) de l’Hospital del Mar les quals treballen amb un sistema de distribució de medicació de stock.

Microgrids and their operations

Interconnection of loads and small size generation forms a new type of distribution systems, the Microgrid. The microgrids can be operated together with the utility grid or be operated autonomously in an island. Thesesmall grids present a new paradigm of the construction of the low voltage distribution systems. The microgrids in the distribution systems can become small, controllable units, which immediately react to the system's changes. Along with that the microgrids can realize the special properties, such as increasing the reliability, reducing losses, voltage sag correction, uninterruptible supplying. The goals of the thesis are to explain the principles of the microgrid's functioning, to clarify the main ideas and positive features of the microgrids, to find out and prove their advantages and explain why they are so popular nowadays all over the world. The practical aims of the thesis are to construct and build a test setup of a microgrid based on two inverters from SMA Technologie AG in the laboratory and to test all the main modes and parameters of the microgrid's operating. Also the purpose of the thesis is to test the main component of the microgrid - the battery inverter which controls allthe processes and energy flows inside a microgrid and communicates with the main grid. Based on received data the main contribution of the thesis consists of the estimation of the established microgrid from the reliability, economy and simplicity of operating points of view and evaluation ofthe advisability of its use in different conditions. Moreover, the thesis assumes to give the recommendations and advice for the future investigations of the built system.

Oral pathogens in duwl's: risk of infection and strategies for their control

Water lines are an important source of potentíal contamination. Every dental unit is equipped with small-bore flexible plastic tubing to bring water to different hand pieces, such as the air/water syringe, the ultrasonic scaler or the high-speed hand piece. Most dental units are connected directly to municipal distribution systems for potable water and chlorinated or not, this water contains diverse...

Tasasähkönjakelun käyttöpotentiaalin määrittäminen

Sähkönjakeluverkkojen kehittäminen nykyistä käyttövarmemmiksi ja taloudellisemmiksi vaatii jatkuvasti uusia ratkaisumalleja. Lupaavaksi tekniikaksi sähkönjakeluverkkojen kehittämisessä on osoittautumassa tasasähkönjakelu tehoelektronisten komponenttien kehittyessä ja hintojen laskiessa samanaikaisesti. Pienjännitedirektiivi mahdollistaa tasajännitteen myötä aiempaa suurempien jännitteiden käytön pienjänniteverkoissa. Tasajännitteen käytöllä voidaan saavuttaa etuja mm. tehonsiirtokyvyssä, sähkönlaadussa, käyttövarmuudessa sekä kustannuksissa. Työssä tehdään yksityiskohtaisia teknistaloudellisia tarkasteluja perinteistä 20/0,4 kV tekniikkaa, 1000 V sähkönjakelua sekä tasasähköjärjestelmiä hyödyntäen ja verrataan näiden järjestelmien kustannuksia ja ominaisuuksia toisiinsa. Tutkimusalueet on valittu Fortum Sähkönsiirto Oy:n maaseutu- ja taajamaverkoista. Työssä pyritään hahmotta-maan teknistaloudellista käyttöaluetta eri tasasähkönjakelujärjestelmille sekä määrittä-mään tasasähkönjakelun käyttöpotentiaali tutkimuskohteena olleissa verkoissa. Lisäksi tutkitaan eri tekijöiden vaikutuksia tasasähköjakelun kannattavuuteen ja käyttövarmuu-teen sekä pyritään tuomaan esiin muitakin tasasähkönjakelujärjestelmien ominaisuuksia.

En face optical coherence tomography of foveal microstructure in full-thickness macular hole: a model to study perifoveal müller cells.

PURPOSE: To characterize perifoveal intraretinal cavities observed around full-thickness macular holes (MH) using en face optical coherence tomography and to establish correlations with histology of human and primate maculae. DESIGN: Retrospective nonconsecutive observational case series. METHODS: Macular en face scans of 8 patients with MH were analyzed to quantify the areas of hyporeflective spaces, and were compared with macular flat mounts and sections from 1 normal human donor eye and 2 normal primate eyes (Macaca fascicularis). Immunohistochemistry was used to study the distribution of glutamine synthetase, expressed by Müller cells, and zonula occludens-1, a tight-junction protein. RESULTS: The mean area of hyporeflective spaces was lower in the inner nuclear layer (INL) than in the complex formed by the outer plexiform (OPL) and the Henle fiber layers (HFL): 5.0 × 10(-3) mm(2) vs 15.9 × 10(-3) mm(2), respectively (P < .0001, Kruskal-Wallis test). In the OPL and HFL, cavities were elongated with a stellate pattern, whereas in the INL they were rounded and formed vertical cylinders. Immunohistochemistry confirmed that Müller cells followed a radial distribution around the fovea in the frontal plane and a "Z-shaped" course in the axial plane, running obliquely in the OPL and HFL and vertically in the inner layers. In addition, zonula occludens-1 co-localized with Müller cells within the complex of OPL and HFL, indicating junctions in between Müller cells and cone axons. CONCLUSION: The dual profile of cavities around MHs correlates with Müller cell morphology and is consistent with the hypothesis of intra- or extracellular fluid accumulation along these cells.

1000 V sähkönjakelujärjestelmän teknistaloudellisen kannattavuuden tarkastelu

Tässä työssä tutkitaan 1000 V pienjännitejakelun taloudellista kannattavuutta. Tutkimus perustuu teoreettiseen tarkasteluun, jossa noudatetaan yleisiä verkostosuunnittelun periaatteita. EU-lainsäädäntö mahdollistaa 1000 V pienjänniteportaan sijoittamisen nykyisen keskijänniteverkon ja pienjänniteverkon väliin lisäten kolmannen jakelujänniteportaan nykyään käytettävien 20 kV ja 0,4 kV väliin. Jakeluverkkojen kehittämiseksi on etsittävä ratkaisu, joka on taloudellinen sekä asiakkaiden että verkonhaltijoiden kannalta. Tällaiset ratkaisut pienentävät verkon käytön kokonaiskustannuksia ja parantavat sähkön laatua. Lisättäessä jakeluverkkoon kolmas jänniteporras, keskijänniteverkon johtopituus lyhenee ja varsinkin lyhyiden haarajohtojen määrä vähenee. Tämä vähentää keskijänniteverkossa esiintyvien keskeytysten määrää ja pienentää keskeytyskustannuksia. Kilovoltin järjestelmä on kannattava korvattaessa sillä osa keskijänniteverkkoa, tai estettäessä perinteisellä järjestelmällä tarvittava muuntopiirin jakaminen. Osana varsinaista pienjänniteverkkoa ei kilovoltinjärjestelmä ole kannattava. Tässä työssä kolmijänniteportaista jakeluverkkoa tutkitaan teoreettisilla verkkosuunnitelmilla, joita tehdään muutamille perusverkkotopologioille. Taloudellista kannattavuutta tutkitaan vertaamalla perinteistä kaksijänniteportaista ja kolmijänniteportaista verkkoratkaisua kustannusten suhteen teknisten reunaehtojen puitteissa. 1000 V pienjännitejakelu vaatii uudenlaisia verkostokomponentteja. Näistä on erityisesti käsitelty 1/0,4 kV pienjännitemuuntajaa. Muuntajasuunnittelun lähtökohtana on 1000 V verkon käyttäminen keskijänniteverkon jatkeena maasta erotettuna verkkona.