Using a cohesive damage model to predict the tensile behaviour of CFRP single-strap repairs

This work addresses both experimental and numerical analyses regarding the tensile behaviour of CFRP single-strap repairs. Two fundamental geometrical parameters were studied: overlap length and patch thickness. The numerical model used ABAQUS® software and a developed cohesive mixed-mode damage model adequate for ductile adhesives, and implemented within interface finite elements. Stress analyses and strength predictions were carried out. Experimental and numerical comparisons were performed on failure modes, failure load and equivalent stiffness of the repair. Good correlation was found between experimental and numerical results, showing that the proposed model can be successfully applied to bonded joints or repairs.

Mu-Chlorido-Bridged Dimanganese(II) complexes of the schiff base derived from [2+2] condensation of 2,6-diformyl-4-methylphenol and 1,3-bis(3-aminopropyl)tetramethyldisloxane: structure, magnetismo, electrochemical behaviour, and catalytic oxidation of secondary alcohols

The reaction of 2,6-diformyl-4-methylphenol with 1,3-bis(3-aminopropyl)tetramethyldisiloxane in the presence of MnCl2 in a 1:1:2 molar ratio in methanol afforded a dinuclear -chlorido-bridged manganese(II) complex of the macrocyclic [2+2] condensation product (H2L), namely, [Mn2Cl2(H2L)(HL)]Cl center dot 3H(2)O (1). The latter afforded a new compound, namely, [Mn2Cl2(H2L)(2)][MnCl4]center dot 4CH(3)CN center dot 0.5CHCl(3 center dot)0.4H(2)O (2), after recrystallisation from 1:1 CHCl3/CH3CN. The co-existence of the free and complexed azomethine groups, phenolato donors, mu-chlorido bridges, and the disiloxane unit were well evidenced by ESI mass spectrometry and FTIR spectroscopy and confirmed by X-ray crystallography. The magnetic measurements revealed an antiferromagnetic interaction between the two high-spin (S = 5/2, g = 2) manganese(II) ions through the mu-chlorido bridging ligands. The electrochemical behaviour of 1 and 2 has been studied, and details of their redox properties are reported. Both compounds act as catalysts or catalyst precursors in the solvent-free low-power microwave-assisted oxidation of selected secondary alcohols, for example, 1-phenylethanol, cyclohexanol, 2- and 3-octanol, to the corresponding ketones in the absence of solvent. The highest yield of 72% was achieved for 1-phenylethanol by using a maximum of 1% molar ratio of catalyst relative to substrate.

Política(s) de saúde no trabalho : um inquérito sociológico às empresas portuguesas

Resumo Política(s) de saúde no trabalho: um inquérito sociológico às empresas portuguesas A literatura portuguesa sobre políticas, programas e actividades de Segurança, Higiene e Saúde no Trabalho (abreviadamente, SH&ST) é ainda escassa. Com este projecto de investigação pretende-se (i) colmatar essa lacuna, (ii) melhorar o conhecimento dos sistemas de gestão da saúde e segurança no trabalho e (iii) contribuir para a protecção e a promoção da saúde dos trabalhadores. Foi construída uma tipologia com cinco grupos principais de políticas, programas e actividades: A (Higiene & Segurança no Trabalho / Melhoria do ambiente físico de trabalho); B (Avaliação de saúde / Vigilância médica / Prestação de cuidados de saúde); C (Prevenção de comportamentos de risco/ Promoção de estilos de vida saudáveis); D (Intervenções a nível organizacional / Melhoria do ambiente psicossocial de trabalho); E (Actividades e programas sociais e de bem-estar). Havia uma lista de mais de 60 actividades possíveis, correspondendo a um índice de realização de 100%. Foi concebido e desenhado, para ser auto-administrado, um questionário sobre Política de Saúde no Local de Trabalho. Foram efectuados dois mailings, e um follow-up telefónico. O trabalho de campo decorreu entre a primavera de 1997 e o verão de 1998. A amostra (n=259) é considerada representativa das duas mil maiores empresas do país. Uma em cada quatro é uma multinacional. A taxa de sindicalização rondava os 30% da população trabalhadora, mas apenas 16% dos respondentes assinalou a existência de representantes dos trabalhadores eleitos para a SH&ST. A hipótese de investigação principal era a de que as empresas com um sistema integrado de gestão da SH&ST seriam também as empresas com um (i) maior número de políticas, programas e actividades de saúde; (ii) maior índice de saúde; (iii) maior índice de realização; e (iv) maior percentagem dos encargos com a SH&ST no total da massa salarial. As actividades de tipo A e B, tradicionalmente associadas à SH&ST, representavam, só por si, mais de 57% do total. Os resultados, correspondentes às respostas da Secção C do questionário, apontam, para (i) a hipervalorização dos exames de medicina do trabalho; e por outro para (ii) o subaproveitamento de um vasto conjunto de actividades (nomeadamente as de tipo D e E), que são correntemente levadas a cabo pelas empresas e que nunca ou raramente são pensadas em termos de protecção e promoção da saúde dos trabalhadores. As actividades e os programas de tipo C (Prevenção de comportamentos de risco/Promoção de estilos de vida saudáveis), ainda eram as menos frequentes entre nós, a seguir aos Programas sociais e de bem-estar (E). É a existência de sistemas de gestão integrados de SH&ST, e não o tamanho da empresa ou outra característica sociodemográfica ou técnico-organizacional, que permite predizer a frequência de políticas de saúde mais activas e mais inovadores. Os três principais motivos ou razões que levam as empresas portuguesas a investir na protecção e promoção da saúde dos seus trabalhadores eram, por ordem de frequência, (i) o absentismo em geral; (ii) a produtividade, qualidade e/ou competitividade, e (iii) a filosofia de gestão ou cultura organizacional. Quanto aos três principais benefícios que são reportados, surge em primeiro lugar (i) a melhoria da saúde dos trabalhadores, seguida da (ii) melhoria do ambiente do ambiente de trabalho e, por fim, (iii) a melhoria da produtividade, qualidade e/ou competitividade.Quanto aos três principais obstáculos que se põem, em geral, ao desenvolvimento das iniciativas de saúde, eles seriam os seguintes, na percepção dos respondentes: (i) a falta de empenho dos trabalhadores; (ii) a falta de tempo; e (iii) os problemas de articulação/ comunicação a nível interno. Por fim, (i) o empenho das estruturas hierárquicas; (ii) a cultura organizacional propícia; e (iii) o sentido de responsabilidade social surgem, destacadamente, como os três principais factores facilitadores do desenvolvimento da política de saúde no trabalho. Tantos estes factores como os obstáculos são de natureza endógena, susceptíveis portanto de controlo por parte dos gestores. Na sua generalidade, os resultados deste trabalho põem em evidência a fraqueza teóricometodológica de grande parte das iniciativas de saúde, realizadas na década de 1990. Muitas delas seriam medidas avulsas, que se inserem na gestão corrente das nossas empresas, e que dificilmente poderão ser tomadas como expressão de uma política de saúde no local de trabalho, (i) definida e assumida pela gestão de topo, (ii) socialmente concertada, (iii) coerente, (iv) baseada na avaliação de necessidades e expectativas de saúde dos trabalhadores, (v) divulgada, conhecida e partilhada por todos, (vi) contingencial, flexível e integrada, e, por fim, (vii) orientada por custos e resultados. Segundo a Declaração do Luxemburgo (1997), a promoção da saúde engloba o esforço conjunto dos empregadores, dos trabalhadores, do Estado e da sociedade civil para melhorar a segurança, a saúde e o bem-estar no trabalho, objectivo isso que pode ser conseguido através da (i) melhoria da organização e das demais condições de trabalho, da (ii) participação efectiva e concreta dos trabalhadores bem como do seu (iii) desenvolvimento pessoal. Abstract Health at work policies: a sociological inquiry into Portuguese corporations Portuguese literature on workplace health policies, programs and activities is still scarce. With this research project the author intends (i) to improve knowledge on the Occupational Health and Safety (shortly thereafter, OSH) management systems and (ii) contribute to the development of health promotion initiatives at a corporate level. Five categories of workplace health initiatives have been identified: (i) Occupational Hygiene and Safety / Improvement of Physical Working Environment (type A programs); (ii) Health Screening, Medical Surveillance and Other Occupational Health Care Provision (type B programs); (iii) Preventing Risk Behaviours / Promoting Healthy Life Styles (type C programs); (iv) Organisational Change / Improvement of Psycho-Social Working Environment (type D programs); and (v) Industrial and Social Welfare (type E programs). A mail questionnaire was sent to the Chief Executive Officer of the 1500 largest Portuguese companies, operating in the primary and secondary sectors (≥ 100 employees) or tertiary sector (≥ 75 employees). Response rate has reached about 20% (259 respondents, representing about 300 companies). Carried out between Spring 1997 and Summer 1998, the fieldwork has encompassed two direct mailings and one phone follow-up. Sample is considered to be representative of the two thousand largest companies. One in four is a multinational. Union membership rate is about 30%, but only 16% has reported the existence of a workers’ health and safety representative. The most frequent workplace health initiatives were those under the traditional scope of the OSH field (type A and B programs) (57% of total) (e.g., Periodical Medical Examinations; Individual Protective Equipment; Assessment of Working Ability). In SMEs (< 250) it was less likely to find out some time-consuming and expensive activities (e.g., Training on OSH knowledge and skills, Improvement of environmental parameters as ventilation, lighting, heating).There were significant differences in SMEs, when compared with the larger ones (≥ 250) concerning type B programs such as Periodical medical examinations, GP consultation, Nursing care, Other medical and non-medical specialities (e.g., psychiatrist, psychologist, ergonomist, physiotherapist, occupational social worker). With regard to type C programs, there were a greater percentage of programs centred on Substance abuse (tobacco, alcohol, and drug) than on Other health risk behaviours. SMEs representatives reported very few prevention- oriented programs in the field of Drug abuse, Nutrition, Physical activity, Off- job accidents, Blood pressure or Weight control. Frequency of type D programs included Training on Human Resources Management, Training on Organisational Behaviour, Total Quality Management, Job Design/Ergonomics, and Workplace rehabilitation. In general, implementation of this type of programs (Organisational Change / Improvement of Psychosocial Working Environment) is not largely driven by health considerations. Concerning Industrial and Social Welfare (Type E programs), the larger employers are in a better position than SMEs to offer to their employees a large spectrum of health resources and facilities (e.g., Restaurant, Canteen, Resting room, Transport, Infra-structures for physical activity, Surgery, Complementary social protection, Support to recreational and cultural activities, Magazine or newsletter, Intranet). Other workplace health promotion programs like Training on Stress Management, Employee Assistance Programs, or Self-help groups are uncommon in the Portuguese worksites. The existence of integrated OSH management systems, not the company size, is the main variable explaining the implementation of more active and innovative workplace health policies in Portugal. The three main prompting factors reported by employers for health protection and promotion initiatives are: (i) Employee absenteeism; (ii) Productivity, quality and/or competitiveness; and (iii) Corporate culture/management philosophy. On the other hand, (i) Improved staff’s health, (ii) Improved working environment and (iii) Improved productivity, quality and/or competitiveness were the three main benefits reported by companies’ representatives, as a result of successful implementation of workplace health initiatives. (i) Lack of staff commitment; (ii) Lack of time; and (iii) Problems of co-operation and communication within company or establishment (iii) are perceived to be the main barriers companies must cope with. Asked about the main facilitating factors, these companies have pointed out the following ones: (i) Top management commitment; (ii) Corporate culture; and (iii) Sense of social responsibility. This sociological research report shows the methodological weaknesses of workplace health initiatives, carried out by Portuguese companies during the last ‘90s. In many cases, these programs and actions were not part of a corporate health strategy and policy, (i) based on the assessment of workers’ health needs and expectancies, (ii) advocated by the employer or the chief executive officer, (ii) planned and implemented with the staff consultation and participation or (iv) evaluated according to a cost-benefit analysis. In short, corporate health policy and action were still rather based on more traditional OSH approaches and should be reoriented towards Workplace Health Promotion (WHP) approach. According to the Luxembourg Declaration of Workplace Health Promotion in the European Union (1997), WHP is “a combination of: (i) improving the work organisation and environment; (ii) promoting active participation; (iii) encouraging personal development”.Résumée Politique(s) de santé au travail: une enquête sociologique aux entreprises portugaises Au Portugal on ne sait presque rien des politiques de santé au travail, adoptés par les entreprises. Avec ce projet de recherche, on veut (i) améliorer la connaissance sur les systèmes de gestion de la santé et de la sécurité au travail et, au même temps, (ii) contribuer au développement de la promotion de la santé des travailleurs. Une typologie a été usée pour identifier les politiques, programmes et actions de santé au travail: A. Amélioration des conditions de travail / Sécurité au travail; B. Médecine du travail /Santé au travail; C. Prévention des comportements de risque / Promotion de styles de vie sains; D. Interventions organisationnelles / Amélioration des facteurs psychosociaux au travail; E. Gestion de personnel et bien-être social. Un questionnaire postal a été envoyé au représentant maximum des grandes entreprises portugaises, industrielles (≥ 100 employés) ou des services (≥ 75 employés). Le taux de réponse a été environ 20% (259 répondants, concernant trois centaines d’entreprises et d’établissements). La recherche de champ, conduite du printemps 1997 à l’été 1998, a compris deux enquêtes postales et un follow-up téléphonique. L´échantillon est représentatif de la population des deux miles plus grandes entreprises. Un quart sont des multinationales. Le taux de syndicalisation est d’environ 30%. Toutefois, il y a seulement 16% de lieux de travail avec des représentants du personnel pour la santé et sécurité au travail. Les initiatives de santé au travail les plus communes sont celles concernant le domaine plus traditionnel (types A et B) (57% du total): par exemple, les examens de médecine du travail, l’équipement de protection individuelle, les tests d’aptitude au travail. En ce qui concerne les programmes de type C, les plus fréquents sont le contrôle et la prévention des addictions (tabac, alcool, drogue). Les interventions dans le domaine de du système technique et organisationnelle du travail peuvent comprendre les courses de formation en gestion de ressources humaines ou en psychosociologie des organisations, l’ergonomie, le travail posté ou la gestion de la qualité totale. En général, la protection et la promotion de la santé des travailleurs ne sont pas prises en considération dans l’implémentation des initiatives de type D. Il y a des différences quand on compare les grandes entreprises et les moyennes en matière de politique de gestion du personnel e du bien-être (programmes de type E, y compris l’allocation de ressources humaines ou logistiques comme, par exemple, restaurant, journal d’entreprise, transports, installations et équipements sportifs). D’autres activités de promotion de la santé au travail comme la formation en gestion du stress, les programmes d’ assistance aux employés, ou les groupes de soutien et d’auto-aide sont encore très peu fréquents dans les entreprises portugaises. C’est le système intégré de gestion de la santé et de la sécurité au travail, et non pas la taille de l’entreprise, qui aide à prédire l’existence de politiques actives et innovatrices dans ce domaine. Les trois facteurs principaux qui encouragent les actions de santé (prompting factors, en anglais) sont (i) l’absentéisme (y compris la maladie), (ii) les problèmes liés à la productivité, qualité et/ou la compétitivité, et aussi (iii) la culture de l’entreprise/philosophie de gestion. Du coté des bénéfices, on a obtenu surtout l’amélioration (i) de la santé du personnel, (ii) des conditions de travail, et (iii) de la productivité, qualité et/ou compétitivité.Les facteurs qui facilitent les actions de santé au travail sont (i) l’engagement de la direction, (ii) la culture de l’entreprise, et (iii) le sens de responsabilité sociale. Par contre, les obstacles à surmonter, selon les organisations qui ont répondu au questionnaire, seraient surtout (i) le manque d’engagement des travailleurs et de leur représentants, (ii) le temps insuffisant, et (iii) les problèmes de articulation/communication au niveau interne de l’entreprise/établissement. Ce travail de recherche sociologique montre la faiblesse méthodologique des services et activités de santé et sécurité au travail, mis en place par les entreprises portugaises dans les années de 1990, à la suite des accords de concertation sociale de 1991. Dans beaucoup de cas, (i) ces politiques de santé ne font pas partie encore d’un système intégré de gestion, (ii) il n’a pas d’évaluation des besoins et des expectatives des travailleurs, (iii) c’est très bas ou inexistant le niveau de participation du personnel, (iv) on ne fait pas d’analyse coût-bénéfice. On peut conclure que les politiques de santé au travail sont plus proches de la médecine du travail et de la sécurité au travail que de la promotion de la santé des travailleurs. Selon la Déclaration du Luxembourg sur la Promotion de la Santé au Lieu de Travail dans la Communauté Européenne (1997), celle-ci « comprend toutes les mesures des employeurs, des employés et de la société pour améliorer l'état de santé et le bien être des travailleurs » e « ceci peut être obtenu par la concentration des efforts dans les domaines suivants: (i) amélioration de l'organisation du travail et des conditions de travail ; (ii) promotion d'une participation active des collaborateurs ; (iii) renforcement des compétences personnelles ».

The solvation and electrochemical behaviour of Copper acetylacetonate complexes in ionic liquids

The behavior of copper(II) complexes of pentane-2,4-dione and 1,1,1,5,5,5-hexafluoro-2,4-pentanedione, [Cu(acac)(2) (1) and [Cu(HFacac)(2)(H2O)] (2), in ionic liquids and molecular organic solvents, was studied by spectroscopic and electrochemical techniques. The electron paramagnetic resonance characterization (EPR) showed well-resolved spectra in most solvents. In general the EPR spectra of [Cu(acac)(2)] show higher g(z) values and lower hyperfine coupling constants, A(z), in ionic liquids than in organic solvents, in agreement with longer Cu-O bond lengths and higher electron charge in the copper ion in the ionic liquids, suggesting coordination of the ionic liquid anions. For [Cu(HFacac)(2)(H2O)] the opposite was observed suggesting that in ionic liquids there is no coordination of the anions and that the complex is tetrahedrically distorted. The redox properties of the Cu(II) complexes were investigated by cyclic voltammetry (CV) at a Pt electrode (d = 1 mm), in bmimBF(4) and bmimNTf(2) ionic liquids and, for comparative purposes, in neat organic solvents. The neutral copper(II) complexes undergo irreversible reductions to Cu(I) and Cu(0) species in both ILs and common organic solvents (CH2Cl2 or acetonitrile), but, in ILs, they are usually more easier to reduce (less cathodic reduction potential) than in the organic solvents. Moreover, 1 and 2 are easier to reduce in bmimNTf(2) than in bmimBF(4) ionic liquid. (C) 2013 Elsevier B.V. All rights reserved.

The solvation and redox behaviour of mixed ligand COPPER(II) complexes of acetylacetonate and aromatic dimines in ionic liquids

The behavior of two cationic copper complexes of acetylacetonate and 2,2'-bipyridine or 1,10-phenanthroline, [Cu(acac)(bipy)]Cl (1) and [Cu(acac)(phen)]Cl (2), in organic solvents and ionic liquids, was studied by spectroscopic and electrochemical techniques. Both complexes showed solvatochromism in ionic liquids although no correlation with solvent parameters could be obtained. By EPR spectroscopy rhombic spectra with well-resolved superhyperfine structure were obtained in most ionic liquids. The spin Hamiltonian parameters suggest a square pyramidal geometry with coordination of the ionic liquid anion. The redox properties of the complexes were investigated by cyclic voltammetry at a Pt electrode (d = 1 mm) in bmimBF(4) and bmimNTf(2) ionic liquids. Both complexes 1 and 2 are electrochemically reduced in these ionic media at more negative potentials than when using organic solvents. This is in agreement with the EPR characterization, which shows lower A(z) and higher g(z) values for the complexes dissolved in ionic liquids, than in organic solvents, due to higher electron density at the copper center. The anion basicity order obtained by EPR is NTf2-, N(CN)(2)(-), MeSO4- and Me2PO4-, which agrees with previous determinations. (C) 2013 Elsevier B.V. All rights reserved.

Tensile behaviour of single and double-strap repairs on aluminium structures

In this work, an experimental study was performed on the influence of plug filling, loading rate and temperature on the tensile strength of single-strap (SS) and double-strap (DS) repairs on aluminium structures. The experimental programme includes repairs with different values of overlap length (LO=10, 20 and 30 mm), and with and without plug filling. The influence of the testing speed on the repairs strength is also addressed (considering 0.5, 5 and 25 mm/min). Accounting for the temperature effects, tests were carried out at room temperature, 50ºC and 80ºC. This will permit a comparative evaluation of the adhesive tested below and above the Glass Transition Temperature (Tg), established by the manufacturer at 67ºC. The global tendencies of the test results concerning the plug filling and overlap length analyses are interpreted from the fracture modes and typical stress distributions for bonded repairs. According to the results obtained from this work, design guidelines for repairing aluminium structures were recommended.

µ-Chlorido-bridged dimanganese(II) complexes of the schiff base derived from [2+2] condensation of 2,6-diformyl-4-methylphenol and 1,3-bis(3-aminopropyl)tetramethyldisiloxane: structure, magnetismo, electrochemical behaviour, and catalytic oxidation of secondary alcohols

The reaction of 2,6-diformyl-4-methylphenol with 1,3-bis(3-aminopropyl)tetramethyldisiloxane in the presence of MnCl2 in a 1:1:2 molar ratio in methanol afforded a dinuclear -chlorido-bridged manganese(II) complex of the macrocyclic [2+2] condensation product (H2L), namely, [Mn2Cl2(H2L)(HL)]Cl center dot 3H(2)O (1). The latter afforded a new compound, namely, [Mn2Cl2(H2L)(2)][MnCl4]center dot 4CH(3)CN center dot 0.5CHCl(3 center dot)0.4H(2)O (2), after recrystallisation from 1:1 CHCl3/CH3CN. The co-existence of the free and complexed azomethine groups, phenolato donors, mu-chlorido bridges, and the disiloxane unit were well evidenced by ESI mass spectrometry and FTIR spectroscopy and confirmed by X-ray crystallography. The magnetic measurements revealed an antiferromagnetic interaction between the two high-spin (S = 5/2, g = 2) manganese(II) ions through the mu-chlorido bridging ligands. The electrochemical behaviour of 1 and 2 has been studied, and details of their redox properties are reported. Both compounds act as catalysts or catalyst precursors in the solvent-free low-power microwave-assisted oxidation of selected secondary alcohols, for example, 1-phenylethanol, cyclohexanol, 2- and 3-octanol, to the corresponding ketones in the absence of solvent. The highest yield of 72% was achieved for 1-phenylethanol by using a maximum of 1% molar ratio of catalyst relative to substrate.

Living bacteria rheology: Population growth, aggregation patterns, and collective behaviour under diferente shear flows

The activity of growing living bacteria was investigated using real-time and in situ rheology-in stationary and oscillatory shear. Two different strains of the human pathogen Staphylococcus aureus-strain COL and its isogenic cell wall autolysis mutant, RUSAL9-were considered in this work. For low bacteria density, strain COL forms small clusters, while the mutant, presenting deficient cell separation, forms irregular larger aggregates. In the early stages of growth, when subjected to a stationary shear, the viscosity of the cultures of both strains increases with the population of cells. As the bacteria reach the exponential phase of growth, the viscosity of the cultures of the two strains follows different and rich behaviors, with no counterpart in the optical density or in the population's colony-forming units measurements. While the viscosity of strain COL culture keeps increasing during the exponential phase and returns close to its initial value for the late phase of growth, where the population stabilizes, the viscosity of the mutant strain culture decreases steeply, still in the exponential phase, remains constant for some time, and increases again, reaching a constant plateau at a maximum value for the late phase of growth. These complex viscoelastic behaviors, which were observed to be shear-stress-dependent, are a consequence of two coupled effects: the cell density continuous increase and its changing interacting properties. The viscous and elastic moduli of strain COL culture, obtained with oscillatory shear, exhibit power-law behaviors whose exponents are dependent on the bacteria growth stage. The viscous and elastic moduli of the mutant culture have complex behaviors, emerging from the different relaxation times that are associated with the large molecules of the medium and the self-organized structures of bacteria. Nevertheless, these behaviors reflect the bacteria growth stage.

Investigation of structural effects and behaviour of pseudomonas aeruginosa amidase encapsulated in reserved micelles

The acetohydroxamic acid synthesis reaction was studied using whole cells, cell-free extract and purified amidase from the strains of Pseudomonas aeruginosa L10 and A13 entrapped in a reverse micelles system composed of cationic surfactant tetradecyltrimethyl ammonium bromide. The specific activity of amidase, yield of synthesis and storage stability were determined for the reversed micellar system as well as for free amidase in conventional buffer medium. The results have revealed that amidase solutions in the reverse micelles system exhibited a substantial increase in specific activity, yield of synthesis and storage stability. In fact, whole cells from P. aeruginosa L10 and AI3 in reverse micellar medium revealed an increase in specific activity of 9.3- and 13.9-fold, respectively, relatively to the buffer medium. Yields of approximately 92% and 66% of acetohydroxamic acid synthesis were obtained for encapsulated cell free extract from P. aeruginosa L10 and A13, respectively. On the other hand, the half-life values obtained for the amidase solutions encapsulated in reverse micelles were overall higher than that obtained for the free amidase solution in buffer medium. Half-life values obtained for encapsulated purified amidase from P. aeruginosa strain L10 and encapsulated cell-free extract from P. aeruginosa strain AI3 were of 17.0 and 26.0 days, respectively. As far as the different sources biocatalyst are concerned, the data presented in this work has revealed that the best results, in both storage stability and biocatalytic efficiency, were obtained when encapsulated cell-free extract from P. aeruginosa strain AI3 at 14/0 of 10 were used. Conformational changes occurring upon encapsulation of both strains enzymes in reverse micelles of TAB in heptane/octanol were additionally identified by FTIR spectroscopy which clarified the biocatalysts performances.

Modifications of MCM-22 zeolite through sequential post-synthesis treatments. Implications on the acidic and catalytic behaviour

Desilication and a combination of alkaline followed by acid treatment were applied to MCM-22 zeolite using two different base concentrations. The samples were characterised by powder X-ray diffraction, Al-27 and Si-29 MAS-NMR spectroscopy, SEM, TEM and low temperature N-2 adsorption. The acidity of the samples was study through pyridine adsorption followed by FTIR spectroscopy and by the analyses of the hydroxyl region. The catalytic behaviour, anticipated by the effect of post-synthesis treatments on the acidity and space available inside the two internal pore systems was evaluated by using the model reaction of m-xylene transformation. The generation of mesoporosity was achieved upon alkaline treatment with 0.05 M NaOH solution and practically no additional gain was obtained when the more concentrate solution, 0.1 M, was used. Instead, Al extraction takes place along with Si, as shown by Si-29 and Al-27 MAS-NMR data, followed by Al deposition as extraframework species. Samples submitted to alkaline plus acid treatments present distinct behaviour. When the lowest NaOH solution was used no relevant effect was observed on the textural characteristics. Additionally, when the acid treatment was performed on an already fragilized MCM-22 structure, due to previous desilication with 0.1 M NaOH solution, the extraction of Al from both internal pore systems promotes their interconnection, evolving from a 2-D to a 3-D porous structure. This transformation has a marked effect in the catalytic behaviour, allowing an increase of m-xylene conversion as a consequence of an easier and faster molecular traffic in the 3-D structure. On the other hand, the continuous deposition of extraframework Al species inside the pores leads to a shape selective effect that privileges the formation of the more valuable isomer p-xylene.

Redox-active cytotoxic diorganotin(IV) cycloalkylhydroxamate complexes with different ring sizes: Reduction behaviour and theoretical interpretation

Two series of new diorganotin(IV) cycloalkylhydroxamate complexes with different ring sizes (cyclopropyl, cyclobutyl, cyclopentyl and cyclohexyl), formulated as the mononuclear [R2Sn(HL)(2)] (1:2) (a, R=Bu-n and Ph) and the polymeric [R2SnL](n) (1:1) (b, R=Bu-n) compounds, were prepared and fully characterized. Single crystal X-ray diffraction for [(Bu2Sn)-Bu-n{C5H9C(O)NHO}(2)] (3a) discloses the cis geometry and strong intermolecular NH center dot center dot center dot O interactions. The in vitro cytotoxic activities of the complexes were evaluated against HL-60, Bel-7402, BGC-823 and KB human tumour cell lines, the greater activity concerning [(Bu2Sn)-Bu-n(HL)(2)] [HL=C3H5C(O)NHO (1a), C6H11C(O)NHO (4a)] towards BGC-823. The complexes undergo, by cyclic voltammetry and controlled-potential electrolysis, one irreversible overall two-electron cathodic process at a reduction potential that does not appear to correlate with the antitumour activity. The electrochemical behaviour of [R2Sn(C5H9C(O)NHO)(2)] [R=Bu-n (3a), Ph (7a)] was also investigated using density functional theory (DFT) methods, showing that the ultimate complex structure and the mechanism of its formation are R dependent: for the aromatic (R = Ph) complex, the initial reduction step is centred on the phenyl ligands and at the metal, being followed by a second reduction with Sn-O and Sn-C ruptures, whereas for the alkyl (R=Bu-n) complex the first reduction step is centred on one of the hydroxamate ligands and is followed by a second reduction with Sn-O bond cleavages and preservation of the alkyl ligands. In both cases, the final complexes are highly coordinative unsaturated Sn-II species with the cis geometry, features that can be of biological significance.

How market power affects the behaviour of a pumped storage hydro unit in the day-ahead electricity market?

The integration of large amounts of wind energy in power systems raises important operation issues such as the balance between power demand and generation. The pumped storage hydro (PSH) units are seen as one solution for this issue, avoiding the need for wind power curtailments. However, the behavior of a PSH unit might differ considerably when it operates in a liberalized market with some degree of market power. In this regard, a new approach for the optimal daily scheduling of a PSH unit in the day-ahead electricity market was developed and presented in this paper, in which the market power is modeled by a residual inverse demand function with a variable elasticity. The results obtained show that increasing degrees of market power of the PSH unit correspond to decreasing levels of storage and, therefore, the capacity to integrate wind power is considerably reduced under these circumstances.

Adhesion and wear behaviour of NCD coatings on Si3N4 by micro-abrasion tests

Nanocrystalline diamond (NCD) coatings offer an excellent alternative for tribological applications, preserving most of the intrinsic mechanical properties of polycrystalline CVD diamond and adding to it an extreme surface smoothness. Silicon nitride (Si3N4) ceramics are reported to guarantee high adhesion levels to CVD microcrystalline diamond coatings, but the NCD adhesion to Si3N4 is not yet well established. Micro-abrasion tests are appropriate for evaluating the abrasive wear resistance of a given surface, but they also provide information on thin film/substrate interfacial resistance, i.e., film adhesion. In this study, a comparison is made between the behaviour of NCD films deposited by hot-filament chemical vapour deposition (HFCVD) and microwave plasma assisted chemical vapour deposition (MPCVD) techniques. Silicon nitride (Si3N4) ceramic discs were selected as substrates. The NCD depositions by HFCVD and MPCVD were carried out using H2–CH4 and H2–CH4–N2 gas mixtures, respectively. An adequate set of growth parameters was chosen for each CVD technique, resulting in NCD films having a final thickness of 5 m. A micro-abrasion tribometer was used, with 3 m diamond grit as the abrasive slurry element. Experiments were carried out at a constant rotational speed (80 r.p.m.) and by varying the applied load in the range of 0.25–0.75 N. The wear rate for MPCVD NCD (3.7±0.8 × 10−5 m3N−1m−1) is compatible with those reported for microcrystalline CVD diamond. The HFCVD films displayed poorer adhesion to the Si3N4 ceramic substrates than the MPCVD ones. However, the HFCVD films show better wear resistance as a result of their higher crystallinity according to the UV Raman data, despite evidencing premature adhesion failure.

Micro-abrasion wear behaviour of TiAlCrSiN nanostructured coatings

The injection process of glass fibres reinforced plastics promotes the moulds surface degradation by erosion. In order to improve its wear resistance, several kinds of PVD thin hard coatings were used. It is well-known that nanostructures present a better compromise between hardness and toughness. Indeed, when the coating is constituted by a large number of ultra-thin different layers, cracks and interface troubles tend to decrease. However, it is not clear that these nanostructures present a better wear behaviour in erosion processes. In order to study its wear behaviour, a sputtered PVD nanostructured TiAlCrSiN coating was used. The substrate and film surfaces topography were analyzed by profilometry and atomic force microscopy techniques. Film adhesion to the substrate was evaluated by scratch tests. The surface hardness was measured with a Vickers micro-hardness tester. The wear resistance was evaluated by micro-abrasion with a rotating ball tribometer tests. Slurry of SiC particles in distilled water was used in order to provoke the surface abrasion. Different duration tests were performed in order to analyze the wear evolution. After these tests, the wear mechanisms developed were analyzed by scanning electron microscopy. Wear craters were measured and the wear rate was calculated and discussed. With the same purpose, coated inserts were mounted in an injection mould working with a 30% glass fibres reinforced polypropylene. After 45 000 cycles no relevant wear was registered.

Serologic studies on the behaviour of influenza virus type A in persons of greater São Paulo during 1976, 1978 and 1979

Sera of persons of different age groups collected in 1976, 1978 and 1979 were tested for the presence of HI antibodies against various strains of the H3N2 and H1N1 subtypes of influenza virus. The occurrence of infection by H3N2 subtype was recorded during the 1976-1978 period but in 1979, circulation of this subtype of virus was limited. The prevalence of antibody against A/São Paulo/1/78 (H1N1) was significantly higher than that of antibody to A/USSB/90/77 (HIND in 1978. However in 1979 the predominant strain was A/USSR/90/77 (HIND. Persons under 20 years of age were the most affected by H1N1 subtype. Antibodies to H1N1 subtype were detected in sera of individuals older than 20 years in 1976, before the re-emergence of this strain. Serological results indicate that infections by H3N2 subtype in 1978 occurred in 65.4% of young children (0-4 year group). About 47.0% of children from the 0-4 year group had antibodies to H1N1 subtype in 1979. Antibodies to swine influenza virus were detected in 60% of 60+ year old people.