987 resultados para Processing-speed


Relevância:

30.00% 30.00%

Publicador:

Resumo:

The current optical communications network consists of point-to-point optical transmission paths interconnected with relatively low-speed electronic switching and routing devices. As the demand for capacity increases, then higher speed electronic devices will become necessary. It is however hard to realise electronic chip-sets above 10 Gbit/s, and therefore to increase the achievable performance of the network, electro-optic and all-optic switching and routing architectures are being investigated. This thesis aims to provide a detailed experimental analysis of high-speed optical processing within an optical time division multiplexed (OTDM) network node. This includes the functions of demultiplexing, 'drop and insert' multiplexing, data regeneration, and clock recovery. It examines the possibilities of combining these tasks using a single device. Two optical switching technologies are explored. The first is an all-optical device known as 'semiconductor optical amplifier-based nonlinear optical loop mirror' (SOA-NOLM). Switching is achieved by using an intense 'control' pulse to induce a phase shift in a low-intensity signal propagating through an interferometer. Simultaneous demultiplexing, data regeneration and clock recovery are demonstrated for the first time using a single SOA-NOLM. The second device is an electroabsorption (EA) modulator, which until this thesis had been used in a uni-directional configuration to achieve picosecond pulse generation, data encoding, demultiplexing, and 'drop and insert' multiplexing. This thesis presents results on the use of an EA modulator in a novel bi-directional configuration. Two independent channels are demultiplexed from a high-speed OTDM data stream using a single device. Simultaneous demultiplexing with stable, ultra-low jitter clock recovery is demonstrated, and then used in a self-contained 40 Gbit/s 'drop and insert' node. Finally, a 10 GHz source is analysed that exploits the EA modulator bi-directionality to increase the pulse extinction ratio to a level where it could be used in an 80 Gbit/s OTDM network.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Improving bit error rates in optical communication systems is a difficult and important problem. The error correction must take place at high speed and be extremely accurate. We show the feasibility of using hardware implementable machine learning techniques. This may enable some error correction at the speed required.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Recent advances in technology have produced a significant increase in the availability of free sensor data over the Internet. With affordable weather monitoring stations now available to individual meteorology enthusiasts a reservoir of real time data such as temperature, rainfall and wind speed can now be obtained for most of the United States and Europe. Despite the abundance of available data, obtaining useable information about the weather in your local neighbourhood requires complex processing that poses several challenges. This paper discusses a collection of technologies and applications that harvest, refine and process this data, culminating in information that has been tailored toward the user. In this case we are particularly interested in allowing a user to make direct queries about the weather at any location, even when this is not directly instrumented, using interpolation methods. We also consider how the uncertainty that the interpolation introduces can then be communicated to the user of the system, using UncertML, a developing standard for uncertainty representation.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

In human (D. H. Baker, T. S. Meese, & R. J. Summers, 2007b) and in cat (B. Li, M. R. Peterson, J. K. Thompson, T. Duong, & R. D. Freeman, 2005; F. Sengpiel & V. Vorobyov, 2005) there are at least two routes to cross-orientation suppression (XOS): a broadband, non-adaptable, monocular (within-eye) pathway and a more narrowband, adaptable interocular (between the eyes) pathway. We further characterized these two routes psychophysically by measuring the weight of suppression across spatio-temporal frequency for cross-oriented pairs of superimposed flickering Gabor patches. Masking functions were normalized to unmasked detection thresholds and fitted by a two-stage model of contrast gain control (T. S. Meese, M. A. Georgeson, & D. H. Baker, 2006) that was developed to accommodate XOS. The weight of monocular suppression was a power function of the scalar quantity ‘speed’ (temporal-frequency/spatial-frequency). This weight can be expressed as the ratio of non-oriented magno- and parvo-like mechanisms, permitting a fast-acting, early locus, as befits the urgency for action associated with high retinal speeds. In contrast, dichoptic-masking functions superimposed. Overall, this (i) provides further evidence for dissociation between the two forms of XOS in humans, and (ii) indicates that the monocular and interocular varieties of XOS are space/time scale-dependent and scale-invariant, respectively. This suggests an image-processing role for interocular XOS that is tailored to natural image statistics—very different from that of the scale-dependent (speed-dependent) monocular variety.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

All-optical data processing is expected to play a major role in future optical communications. Nonlinear effects in optical fibers have attractive applications in optical signal processing. In this paper, we review our recent advances in developing all-optical processing techniques at high speed based on optical fiber nonlinearities.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

All-optical data processing is expected to play a major role in future optical communications. Nonlinear effects in optical fibers have attractive applications in optical signal processing. In this paper, we review our recent advances in developing all-optical processing techniques at high speed based on optical fiber nonlinearities.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Improving bit error rates in optical communication systems is a difficult and important problem. The error correction must take place at high speed and be extremely accurate. We show the feasibility of using hardware implementable machine learning techniques. This may enable some error correction at the speed required.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The existence of an optimal span length for 40 Gbit/s WDM transmission systems with hybrid Raman/EDFA amplification is demonstrated. Optimal lengths are obtained for specific amplifier configurations and different fibre arrangements based on SSMF/DCF and SLA/IDF implementation, using a simple nonlinearity management theory.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Melt processing is a critical step in the manufacture of polymer articles and is even more critical when dealing with inhomogeneous polymer-clay nanocomposites systems. The chemical composition, and in particular the clay type and its organic modification, also plays a major contribution in determining the final properties and in particular the thermal and long-term oxidative stability of the resulting polymer nanocomposites. Proper selection and tuning of the process variable should, in principle, lead to improved characteristics of the fabricated product. With multiphase systems containing inorganic nanoclays, however, this is not straightforward and it is often the case that the process conditions are chosen initially to improve one or more desired properties at the expense of others. This study assesses the influence of organo-modified clays and the processing parameters (extrusion temperature and screw speed) on the rheological and morphological characteristics of polymer nanocomposites as well as on their melt and thermo-oxidative stability. Nanocomposites (PPNCs) based on PP, maleated PP and organically modified clays were prepared in different co-rotating twin-screw extruders ranging from laboratory scale to semi-industrial scale. Results show that the amount of surfactant present in similar organo-modified clays affects differently the thermo-oxidative stability of the extruded PPNCs and that changes in processing conditions affect the clay morphology too. By choosing an appropriate set of tuned process variables for the extrusion process it would be feasible to selectively fabricate polymer-clay nanocomposites, with the desired mechanical and thermo-oxidative characteristics. © 2013 Elsevier Ltd. All rights reserved.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

ACM Computing Classification System (1998): I.7, I.7.5.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Temporal-order judgment (TOJ) and simultaneity judgment (SJ) tasks are used to study differences in speed of processing across sensory modalities, stimulus types, or experimental conditions. Matthews and Welch (2015) reported that observed performance in SJ and TOJ tasks is superior when visual stimuli are presented in the left visual field (LVF) compared to the right visual field (RVF), revealing an LVF advantage presumably reflecting attentional influences. Because observed performance reflects the interplay of perceptual and decisional processes involved in carrying out the tasks, analyses that separate out these influences are needed to determine the origin of the LVF advantage. We re-analyzed the data of Matthews and Welch (2015) using a model of performance in SJ and TOJ tasks that separates out these influences. Parameter estimates capturing the operation of perceptual processes did not differ between hemifields by these analyses, whereas parameter estimates capturing the operation of decisional processes differed. In line with other evidence, perceptual processing also did not differ between SJ and TOJ tasks. Thus, the LVF advantage occurs with identical speeds of processing in both visual hemifields. If attention is responsible for the LVF advantage, it does not exert its influence via prior entry.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Strawberries harvested for processing as frozen fruits are currently de-calyxed manually in the field. This process requires the removal of the stem cap with green leaves (i.e. the calyx) and incurs many disadvantages when performed by hand. Not only does it necessitate the need to maintain cutting tool sanitation, but it also increases labor time and exposure of the de-capped strawberries before in-plant processing. This leads to labor inefficiency and decreased harvest yield. By moving the calyx removal process from the fields to the processing plants, this new practice would reduce field labor and improve management and logistics, while increasing annual yield. As labor prices continue to increase, the strawberry industry has shown great interest in the development and implementation of an automated calyx removal system. In response, this dissertation describes the design, operation, and performance of a full-scale automatic vision-guided intelligent de-calyxing (AVID) prototype machine. The AVID machine utilizes commercially available equipment to produce a relatively low cost automated de-calyxing system that can be retrofitted into existing food processing facilities. This dissertation is broken up into five sections. The first two sections include a machine overview and a 12-week processing plant pilot study. Results of the pilot study indicate the AVID machine is able to de-calyx grade-1-with-cap conical strawberries at roughly 66 percent output weight yield at a throughput of 10,000 pounds per hour. The remaining three sections describe in detail the three main components of the machine: a strawberry loading and orientation conveyor, a machine vision system for calyx identification, and a synchronized multi-waterjet knife calyx removal system. In short, the loading system utilizes rotational energy to orient conical strawberries. The machine vision system determines cut locations through RGB real-time feature extraction. The high-speed multi-waterjet knife system uses direct drive actuation to locate 30,000 psi cutting streams to precise coordinates for calyx removal. Based on the observations and studies performed within this dissertation, the AVID machine is seen to be a viable option for automated high-throughput strawberry calyx removal. A summary of future tasks and further improvements is discussed at the end.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Introdução: A cintigrafia óssea é um dos exames mais frequentes em Medicina Nuclear. Esta modalidade de imagem médica requere um balanço apropriado entre a qualidade de imagem e a dose de radiação, ou seja, as imagens obtidas devem conter o número mínimo de contagem necessárias, para que apresentem qualidade considerada suficiente para fins diagnósticos. Objetivo: Este estudo tem como principal objetivo, a aplicação do software Enhanced Planar Processing (EPP), nos exames de cintigrafia óssea em doentes com carcinoma da mama e próstata que apresentam metástases ósseas. Desta forma, pretende-se avaliar a performance do algoritmo EPP na prática clínica em termos de qualidade e confiança diagnóstica quando o tempo de aquisição é reduzido em 50%. Material e Métodos: Esta investigação teve lugar no departamento de Radiologia e Medicina Nuclear do Radboud University Nijmegen Medical Centre. Cinquenta e um doentes com suspeita de metástases ósseas foram administrados com 500MBq de metilenodifosfonato marcado com tecnécio-99m. Cada doente foi submetido a duas aquisições de imagem, sendo que na primeira foi seguido o protocolo standard do departamento (scan speed=8 cm/min) e na segunda, o tempo de aquisição foi reduzido para metade (scan speed=16 cm/min). As imagens adquiridas com o segundo protocolo foram processadas com o algoritmo EPP. Todas as imagens foram submetidas a uma avaliação objetiva e subjetiva. Relativamente à análise subjetiva, três médicos especialistas em Medicina Nuclear avaliaram as imagens em termos da detetabilidade das lesões, qualidade de imagem, aceitabilidade diagnóstica, localização das lesões e confiança diagnóstica. No que respeita à avaliação objetiva, foram selecionadas duas regiões de interesse, uma localizada no terço médio do fémur e outra localizada nos tecidos moles adjacentes, de modo a obter os valores de relação sinal-ruído, relação contraste-ruído e coeficiente de variação. Resultados: Os resultados obtidos evidenciam que as imagens processadas com o software EPP oferecem aos médicos suficiente informação diagnóstica na deteção de metástases, uma vez que não foram encontradas diferenças estatisticamente significativas (p>0.05). Para além disso, a concordância entre os observadores, comparando essas imagens e as imagens adquiridas com o protocolo standard foi de 95% (k=0.88). Por outro lado, no que respeita à qualidade de imagem, foram encontradas diferenças estatisticamente significativas quando se compararam as modalidades de imagem entre si (p≤0.05). Relativamente à aceitabilidade diagnóstica, não foram encontradas diferenças estatisticamente significativas entre as imagens adquiridas com o protocolo standard e as imagens processadas com o EPP software (p>0.05), verificando-se uma concordância entre os observadores de 70.6%. Todavia, foram encontradas diferenças estatisticamente significativas entre as imagens adquiridas com o protocolo standard e as imagens adquiridas com o segundo protocolo e não processadas com o software EPP (p≤0.05). Para além disso, não foram encontradas diferenças estatisticamente significativas (p>0.05) em termos de relação sinal-ruído, relação contraste-ruído e coeficiente de variação entre as imagens adquiridas com o protocolo standard e as imagens processadas com o EPP. Conclusão: Com os resultados obtidos através deste estudo, é possível concluir que o algoritmo EPP, desenvolvido pela Siemens, oferece a possibilidade de reduzir o tempo de aquisição em 50%, mantendo ao mesmo tempo uma qualidade de imagem considerada suficiente para fins de diagnóstico. A utilização desta tecnologia, para além de aumentar a satisfação por parte dos doentes, é bastante vantajosa no que respeita ao workflow do departamento.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Integrated circuit scaling has enabled a huge growth in processing capability, which necessitates a corresponding increase in inter-chip communication bandwidth. As bandwidth requirements for chip-to-chip interconnection scale, deficiencies of electrical channels become more apparent. Optical links present a viable alternative due to their low frequency-dependent loss and higher bandwidth density in the form of wavelength division multiplexing. As integrated photonics and bonding technologies are maturing, commercialization of hybrid-integrated optical links are becoming a reality. Increasing silicon integration leads to better performance in optical links but necessitates a corresponding co-design strategy in both electronics and photonics. In this light, holistic design of high-speed optical links with an in-depth understanding of photonics and state-of-the-art electronics brings their performance to unprecedented levels. This thesis presents developments in high-speed optical links by co-designing and co-integrating the primary elements of an optical link: receiver, transmitter, and clocking.

In the first part of this thesis a 3D-integrated CMOS/Silicon-photonic receiver will be presented. The electronic chip features a novel design that employs a low-bandwidth TIA front-end, double-sampling and equalization through dynamic offset modulation. Measured results show -14.9dBm of sensitivity and energy efficiency of 170fJ/b at 25Gb/s. The same receiver front-end is also used to implement source-synchronous 4-channel WDM-based parallel optical receiver. Quadrature ILO-based clocking is employed for synchronization and a novel frequency-tracking method that exploits the dynamics of IL in a quadrature ring oscillator to increase the effective locking range. An adaptive body-biasing circuit is designed to maintain the per-bit-energy consumption constant across wide data-rates. The prototype measurements indicate a record-low power consumption of 153fJ/b at 32Gb/s. The receiver sensitivity is measured to be -8.8dBm at 32Gb/s.

Next, on the optical transmitter side, three new techniques will be presented. First one is a differential ring modulator that breaks the optical bandwidth/quality factor trade-off known to limit the speed of high-Q ring modulators. This structure maintains a constant energy in the ring to avoid pattern-dependent power droop. As a first proof of concept, a prototype has been fabricated and measured up to 10Gb/s. The second technique is thermal stabilization of micro-ring resonator modulators through direct measurement of temperature using a monolithic PTAT temperature sensor. The measured temperature is used in a feedback loop to adjust the thermal tuner of the ring. A prototype is fabricated and a closed-loop feedback system is demonstrated to operate at 20Gb/s in the presence of temperature fluctuations. The third technique is a switched-capacitor based pre-emphasis technique designed to extend the inherently low bandwidth of carrier injection micro-ring modulators. A measured prototype of the optical transmitter achieves energy efficiency of 342fJ/bit at 10Gb/s and the wavelength stabilization circuit based on the monolithic PTAT sensor consumes 0.29mW.

Lastly, a first-order frequency synthesizer that is suitable for high-speed on-chip clock generation will be discussed. The proposed design features an architecture combining an LC quadrature VCO, two sample-and-holds, a PI, digital coarse-tuning, and rotational frequency detection for fine-tuning. In addition to an electrical reference clock, as an extra feature, the prototype chip is capable of receiving a low jitter optical reference clock generated by a high-repetition-rate mode-locked laser. The output clock at 8GHz has an integrated RMS jitter of 490fs, peak-to-peak periodic jitter of 2.06ps, and total RMS jitter of 680fs. The reference spurs are measured to be –64.3dB below the carrier frequency. At 8GHz the system consumes 2.49mW from a 1V supply.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The aim of this study was to evaluate fat substitute in processing of sausages prepared with surimi of waste from piramutaba filleting. The formulation ingredients were mixed with the fat substitutes added according to a fractional planning 2(4-1), where the independent variables, manioc starch (Ms), hydrogenated soy fat (F), texturized soybean protein (Tsp) and carrageenan (Cg) were evaluated on the responses of pH, texture (Tx), raw batter stability (RBS) and water holding capacity (WHC) of the sausage. Fat substitutes were evaluated in 11 formulations and the results showed that the greatest effects on the responses were found to Ms, F and Cg, being eliminated from the formulation Tsp. To find the best formulation for processing piramutaba sausage was made a complete factorial planning of 2(3) to evaluate the concentrations of fat substitutes in an enlarged range. The optimum condition found for fat substitutes in the sausages formulation were carrageenan (0.51%), manioc starch (1.45%) and fat (1.2%).