Defect-selective photothermal imaging: a sensitive tool for damage mapping in optical coatings

A defect-selective photothermal imaging system for the diagnostics of optical coatings is demonstrated. The instrument has been optimized for pump and probe parameters, detector performance, and signal processing algorithm. The imager is capable of mapping purely optical or thermal defects efficiently in coatings of low damage threshold and low absorbance. Detailed mapping of minor inhomogeneities at low pump power has been achieved through the simultaneous action of a low-noise fiber optic photothermal beam defection sensor and a common-mode-rejection demodulation (CMRD) technique. The linearity and sensitivity of the sensor have been examined theoretically and experimentally, and the signal to noise ratio improvement factor is found to be about 110 compared to a conventional bicell photodiode. The scanner is so designed that mapping of static or shock sensitive samples is possible. In the case of a sample with absolute absorptance of 3.8 x 10(-4), a change in absorptance of about 0.005 x 10(-4) has been detected without ambiguity, ensuring a contrast parameter of 760. This is about 1085% improvement over the conventional approach containing a bicell photodiode, at the same pump power. The merits of the system have been demonstrated by mapping two intentionally created damage sites in a MgF2 coating on fused silica at different excitation powers. Amplitude and phase maps were recorded for thermally thin and thick cases, and the results are compared to demonstrate a case which, in conventional imaging, would lead to a deceptive conclusion regarding the type and location of the damage. Also, a residual damage profile created by long term irradiation with high pump power density has been depicted.

Crystallization as a Tool for Controlling and Designing Properties of Pharmaceutical Solids

The ability to deliver the drug to the patient in a safe, efficacious and cost-effective manner depends largely on the physicochemical properties of the active pharmaceutical ingredient (API) in the solid state. In this context, crystallization is of critical importance in pharmaceutical industry, as it defines physical and powder properties of crystalline APIs. An improved knowledge of the various aspects of crystallization process is therefore needed. The overall goal of this thesis was to gain better understanding of the relationships between crystallization, solid-state form and properties of pharmaceutical solids with a focus on a crystal engineering approach to design technological properties of APIs. Specifically, solid-state properties of the crystalline forms of the model APIs, erythromycin A and baclofen, and the influence of solvent on their crystallization behavior were investigated. In addition, the physical phenomena associated with wet granulation and hot-melting processing of the model APIs were examined at the molecular level. Finally, the effect of crystal habit modification of a model API on its tabletting properties was evaluated. The thesis enabled the understanding of the relationship between the crystalline forms of the model APIs, which is of practical importance for solid-state control during processing and storage. Moreover, a new crystalline form, baclofen monohydrate, was discovered and characterized. Upon polymorph screening, erythromycin A demonstrated high solvate-forming propensity thus emphasizing the need for careful control of the solvent effects during formulation. The solvent compositions that yield the desirable crystalline form of erythromycin A were defined. Furthermore, new examples on solvent-mediated phase transformations taking place during wet granulation of baclofen and hot-melt processing of erythromycin A dihydrate with PEG 6000 are reported. Since solvent-mediated phase transformations involve the crystallization of a stable phase and hence affect the dissolution kinetics and possibly absorption of the API these transformations must be well documented. Finally, a controlled-crystallization method utilizing HPMC as a crystal habit modifier was developed for erythromycin A dihydrate. The crystals with modified habit were shown to posses improved compaction properties as compared with those of unmodified crystals. This result supports the idea of morphological crystal engineering as a tool for designing technological properties of APIs and is of utmost practical interest.

Correlation of plasma IGF-I concentrations and growth rate in aquacultured finfish: a tool for assessing the potential of new diets

A recently developed radioimmunoassay (RIA) for measuring insulin-like growth factor (IGF-I) in a variety of fish species was used to investigate the correlation between growth rate and circulating IGF-I concentrations of barramundi (Lates calcarifer), Atlantic salmon (Salmo salar) and Southern Bluefin tuna (Thunnus maccoyii). Plasma IGF-I concentration significantly increased with increasing ration size in barramundi and IGF-I concentration was positively correlated to growth rates obtained in Atlantic salmon (r2=0.67) and barramundi (r2=0.65) when fed a variety of diet formulations. IGF-I was also positively correlated to protein concentration (r2=0.59). This evidence suggested that measuring IGF-I concentration may provide a useful tool for monitoring fish growth rate and also as a method to rapidly assess different aquaculture diets. However, no such correlation was demonstrated in the tuna study probably due to seasonal cooling of sea surface temperature shortly before blood was sampled. Thus, some recommendations for the design and sampling strategy of nutritional trials where IGF-I concentrations are measured are discussed

Pasteurella multocida detection by 5' Taq nuclease assay: a new tool for use in diagnosing fowl cholera

A 5′ Taq nuclease assay utilising minor groove binder technology and targeting the 16S rRNA gene was designed to detect Pasteurella multocida (the causative agent of fowl cholera) in swabs collected from poultry. The assay was first evaluated using pure cultures. The assay correctly identified four P. multocida taxonomic type strains, 18 P. multocida serovar reference strains and 40 Australian field isolates (17 from poultry, 11 from pigs and 12 from cattle). Representatives of nine other Pasteurella species, 26 other bacterial species (18 being members of the family Pasteurellaceae) and four poultry virus isolates did not react in the assay. The assay detected a minimum of approximately 10 cfu of P. multocida per reaction. Of 79 poultry swabs submitted to the laboratory for routine bacteriological culture, 17 were positive in the 5′ Taq nuclease assay, but only 10 were positive by culture. The other 62 swabs were negative for P. multocida by both 5′ Taq nuclease assay and culture. The assay is suitable for use in diagnosing fowl cholera, is more rapid than bacteriological culture, and may also have application in diagnosing P. multocida infections in cattle and pigs.

Improving the outcomes of foot and ankle surgery. Professional impact of the Australasian College of Podiatric Surgeons' audit tool

Background Surgery is an example of expanded practice scope that enhances podiatry and incorporates inter-professional collaboration. By 2050 demand for foot and ankle procedures is predicted to rise nationally by 61.9%. Performance management of this increase motivated the development of an online audit tool. Developed in collaboration with the Australasian College of Podiatric Surgeons (ACPS), the ACPS audit tool provides real-time data capture and reporting. It is the first audit tool designed in Australia to support and improve the outcomes of foot and ankle surgery. Methods Audit activity in general, orthopaedic, plastic and podiatric surgery was examined using a case study design. Audit participation enablers and barriers were explored. Case study results guided a Delphi survey of international experts experienced or associated with foot and ankle surgery. Delphi survey-derived consensus informed modification of a generic data set from the Royal Australasian College of Surgeons (RACS). Based on the Delphi survey findings the ACPS online audit tool was developed and piloted. Reliability and validity of data entry and usability of this new tool was then assessed with an online survey. Results The case study found surgeon attitudes and behaviours positively impacted audit participation, and also indicated that audit data should be: (1) available in real time, (2) identify practice change, (3) applicable for safety and quality management, and; (4) useful for peer review discussion. The Delphi process established consensus on audit variables to be captured, including the modified RACS generic data set. 382 cases of foot and ankle surgery were captured across 3 months using the new tool. Data entry was found to be valid and reliable. Real-time outcome reporting and practice change identification impacted positively on safety and quality management and assisted peer review discussion. An online survey showed high levels of usability. Conclusions Surgeon contribution to audit tool development resulted in 100% audit participation. The data from the ACPS audit tool supported the ACPS submission to the Medical Services Advisory Committee to list podiatric surgery under Medicare, an outcome noted by the Federal Minister of Health.

A journey access tool to facilitate better health outcomes for people with disabilities

- Background One of the three objectives of the WHO Global Disability Action Plan 2014–2021 is removal of barriers and improved access to health services and programmes. Access to transport contributes to positive health outcomes; however, people with disabilities leaving their dwellings are confronted with barriers to their mobility. Mobility restrictions, sensory or other disabilities increase their vulnerability as road users, exposing them to higher risks of injury. PHSW and CARRS-Q have been collaborating with Handicap International Cambodia (HIC) on a Journey Access Tool (JAT). - Aims Use of the JAT is to (1) Identify transport and journey safety and barriers for people with disability and (2) Evaluation and modification of the tool after trailing to for use by NGOs and government agencies in prioritising actions around barriers. - Methodology The tool has undergone initial proof-of-concept testing in India and Viet Nam, and was trialled in Cambodia in February and May, 2015. Five teams were formed comprising a person with disability (physical, sensory or intellectual), researchers from QUT, staff from HIC, and local university students. The JAT was completed by each team and then discussed and evaluated. Two further Cambodian trials are scheduled for 2015. - Results The JAT is responsive to rural and urban contexts, and has utility for people with different disabilities. Two tools have been developed: a short version for people with a disability to complete independently, or with assistance; and a version for NGOs, DPOs and government. The tool has efficacy for advocacy.   - Conclusion The JAT has potential to assist the Mekong region with: (1) evaluating access for people with disability and other vulnerable members of the community including older people; (2) developing plans for changes to the routes in consultation with local authorities; (3) evaluating the effectiveness of implemented changes in terms of access and health; (4) inputting into policy; (5) The tool can be used for advocacy for change.

Near infrared spectroscopy as a rapid tool to measure volatile aroma compounds in Riesling wine: Possibilities and limits

Volatile chemical compounds responsible for the aroma of wine are derived from a number of different biochemical and chemical pathways. These chemical compounds are formed during grape berry metabolism, crushing of the berries, fermentation processes (i.e. yeast and malolactic bacteria) and also from the ageing and storage of wine. Not surprisingly, there are a large number of chemical classes of compounds found in wine which are present at varying concentrations (ng L-1 to mg L-1), exhibit differing potencies, and have a broad range of volatilities and boiling points. The aim of this work was to investigate the potential use of near infrared (NIR) spectroscopy combined with chemometrics as a rapid and low-cost technique to measure volatile compounds in Riesling wines. Samples of commercial Riesling wine were analyzed using an NIR instrument and volatile compounds by gas chromatography (GC) coupled with selected ion monitoring mass spectrometry. Correlation between the NIR and GC data were developed using partial least-squares (PLS) regression with full cross validation (leave one out). Coefficients of determination in cross validation (R 2) and the standard error in cross validation (SECV) were 0.74 (SECV: 313.6 μg L−1) for esters, 0.90 (SECV: 20.9 μg L−1) for monoterpenes and 0.80 (SECV: 1658 ?g L-1) for short-chain fatty acids. This study has shown that volatile chemical compounds present in wine can be measured by NIR spectroscopy. Further development with larger data sets will be required to test the predictive ability of the NIR calibration models developed.

Rapid and sensitive detection of Avibacterium paragallinarum in the presence of other bacteria using a 5' Taq nuclease assay: A new tool for diagnosing infectious coryza

A 5' Taq nuclease assay specific for Avibacterium paragallinarum was designed and optimized for use in diagnosing infectious coryza. The region chosen for assay design was one of known specificity for Av. paragallinarum. The assay detected Av. paragallinarum reference strains representing the three Page and the eight Kume serovars, and field isolates from diverse geographical locations. No cross-reactions were observed with other Avibacterium species, with other bacteria taxonomically related to Av. paragallinarum nor with bacteria and viruses likely to be present in swabs collected from suspected infectious coryza cases. The detection limit for the assay was 6 to 60 colony-forming units per reaction. Twenty-two out of 53 swabs collected from sick birds reacted in the 5' Taq nuclease assay, whereas Av. paragallinarum was not isolated from any of the swabs. All of the 22 swabs yielded other bacteria in culture. The presence of Av. paragallinarum in the swabs was also demonstrated by sequencing, thereby confirming the ability of the assay to detect Av. paragallinarum in the presence of other bacteria. The ability to quantify bacterial load in the swabs using the 5' Taq nuclease assay was demonstrated.

An identification tool for the Australian weedy Sporobolus species based on random amplified polymorphic DNA (RAPD) profiles

Based on morphological features alone, there is considerable difficulty in identifying the 5 most economically damaging weed species of Sporobolus [viz. S. pyramidalis P. Beauv., S. natalensis (Steud.) Dur and Schinz, S. fertilis (Steud.) Clayton, S. africanus (Poir.) Robyns and Tourney, and S. jacquemontii Kunth.] found in Australia. A polymerase chain reaction (PCR)-based random amplified polymorphic DNA (RAPD) technique was used to create a series of genetic markers that could positively identify the 5 major weeds from the other less damaging weedy and native Sporobolus species. In the initial RAPD profiling experiment, using arbitrarily selected primers and involving 12 species of Sporobolus, 12 genetic markers were found that, when used in combination, could consistently identify the 5 weedy species from all others. Of these 12 markers, the most diagnostic were UBC51490 for S. pyramidalis and S. natalensis; UBC43310.2000.2100 for S. fertilis and S. africanus; and ORA20850 and UBC43470 for S. jacquemontii. Species-specific markers could be found only for S. jacquemontii. In an effort to understand why there was difficulty in obtaining species-specific markers for some of the weedy species, a RAPD data matrix was created using 40 RAPD products. These 40 products amplified by 6 random primers from 45 individuals belonging to 12 species, were then subjected to numerical taxonomy and multivariate system (NTSYS pc version 1.70) analysis. The RAPD similarity matrix generated from the analysis indicated that S. pyramidalis was genetically more similar to S. natalensis than to other species of the 'S. indicus complex'. Similarly, S. jacquemontii was more similar to S. pyramidalis, and S. fertilis was more similar to S. africanus than to other species of the complex. Sporobolus pyramidalis, S. jacquemontii, S. africanus, and S. creber exhibited a low within-species genetic diversity, whereas high genetic diversity was observed within S. natalensis, S. fertilis, S. sessilis, S. elongates, and S. laxus. Cluster analysis placed all of the introduced species (major and minor weedy species) into one major cluster, with S. pyramidalis and S. natalensis in one distinct subcluster and S. fertilis and S. africanus in another. The native species formed separate clusters in the phenograms. The close genetic similarity of S. pyramidalis to S. natalensis, and S. fertilis to S. africanus may explain the difficulty in obtaining RAPD species-specific markers. The importance of these results will be within the Australian dairy and beef industries and will aid in the development of integrated management strategy for these weeds.

A Case of Simple Tool Use in Wild Liontailed Macaques (Macaca silenus)

Three members of a group of liontailed macaques (Macaea silenus) were seen to use leaves for food preparation. Other examples of prey-selection and hunting behaviour in liontailed macaques reflect individual- and group-specific skills. The absence of similar patterns in bonnet macaques (Macaca radiata) living in the same habitat might be related to differences in the social design and indicate the high significance of social aspects for the occurrence and manifestation of innovative behaviour.

Controlled exposure as a management tool for Glasser's disease.

In this study, nasal swabs taken from multiparous sows at weaning time or from sick pigs displaying symptoms of Glasser's disease from farms in Australia [date not given] were cultured and analysed by polymerase chain reaction (PCR). Within each genotype detected on a farm, representative isolates were serotyped by gel diffusion (GD) testing or indirect haemagglutination (IHA) test. Isolates which did not react in any of the tests were regarded as non-typable and were termed serovar NT. Serovars 1, 5, 12, 13 and 14 were classified as highly pathogenic; serovars 2, 4 and 15 being moderately pathogenic; serovar 8 being slightly pathogenic and serovars 3, 6, 7, 9 and 11 being non-pathogenic. Sows were inoculated with the strain of Haemophilus parasuis (serovars 4, 6 and 9 from Farms 1, 2 and 4, respectively) used for controlled challenge 3 and 5 weeks before farrowing. Before farrowing the sows were divided into control and treatment groups. Five to seven days after birth, the piglets of the treatment group were challenged with a strain from the farm which had were used to vaccinate the sows. The effectiveness of the controlled exposure was evaluated by number of piglets displaying clinical signs possibly related to infection, number of antibiotic treatments and pig mortality. Nasal swabs of sick pigs were taken twice a week to find a correlation to infection. A subsample of pigs was weighed after leaving the weaning sheds. The specificity of a realtime PCR amplifying the infB gene was evaluated with 68 H. parasuis isolates and 36 strains of closely related species. 239 samples of DNA from tissues and fluids of 16 experimentally challenged animals were also tested with the realtime PCR, and the results compared with culture and a conventional PCR. The farm experiments showed that none of the controlled challenge pigs showed any signs of illness due to Glasser's disease, although the treatment groups required more antibiotics than the controls. A total of 556 H. parasuis isolates were genotyped, while 150 isolates were serotyped. H. parasuis was detected on 19 of 20 farms, including 2 farms with an extensive history of freedom from Glasser's disease. Isolates belonging to serovars regarded as potentially pathogenic were obtained from healthy pigs at weaning on 8 of the 10 farms with a history of Glasser's disease outbreaks. Sampling 213 sick pigs yielded 115 isolates, 99 of which belonged to serovars that were either potentially pathogenic or of unknown pathogenicity. Only 16 isolates from these sick pigs were of a serovar known to be non-pathogenic. Healthy pigs also had H. parasuis, even on farms free of Glasser's disease. The realtime PCR gave positive results for all 68 H. parasuis isolates and negative results for all 36 non-target bacteria. When used on the clinical material from experimental infections, the realtime PCR produced significantly more positive results than the conventional PCR (165 compared to 86).

WHIPPET: a novel tool for prioritizing invasive plant populations for regional eradication

Large geographic areas can have numerous incipient invasive plant populations that necessitate eradication. However, resources are often deficient to address every infestation. Within the United States, weed lists (either state-level or smaller unit) generally guide the prioritization of eradication of each listed species uniformly across the focus region. This strategy has several limitations that can compromise overall effectiveness, which include spending limited resources on 1) low impact populations, 2) difficult to access populations, or 3) missing high impact populations of low priority species. Therefore, we developed a novel science-based, transparent, analytical ranking tool to prioritize weed populations, instead of species, for eradication and tested it on a group of noxious weeds in California. For outreach purposes, we named the tool WHIPPET (Weed Heuristics: Invasive Population Prioritization for Eradication Tool). Using the Analytic Hierarchy Process that included expert opinion, we developed three major criteria, four sub-criteria, and four sub-sub-criteria, taking into account both species and population characteristics. Subject matter experts weighted and scored these criteria to assess the relative impact, potential spread, and feasibility of eradication (major criteria) for 100 total populations of 19 species. Species-wide population scores indicated that conspecific populations do not necessarily group together in the final ranked output. Thus, priority lists based solely on species-level characteristics are less effective compared to a blended prioritization based on both species attributes and individual population and site parameters. WHIPPET should facilitate a more efficacious decision-making process allocating limited resources to target invasive plant infestations with the greatest predicted impacts to the region under consideration.

Near infrared spectroscopy as a rapid non-invasive tool for agricultural and industrial process management with special reference to avocado and sandalwood industries

Near infrared spectroscopy (NIRS) can play a vital role as a cost effective, rapid, non-invasive, reproducible diagnostic tool for many environmental management, agricultural and industrial waste water monitoring applications. In this paper we highlight the ability of NIRS technology to be used as a diagnostic tool in agricultural and environmental applications through the successful assessment of Fourier Transform NIRS to predict α santalol in sandalwood chip samples, and maturity of ‘Hass’ avocado fruit based on dry matter content. Presented at the Third International Conference on Challenges in Environmental Science & Engineering, CESE-2010. 26 September – 1 October 2010, The Sebel, Cairns, Queensland, Australia.