Characterising the energy performance of centralised HVAC&R systems in the UK

Heating, ventilation, air conditioning and refrigeration (HVAC&R) systems account for more than 60% of the energy consumption of buildings in the UK. However, the effect of the variety of HVAC&R systems on building energy performance has not yet been taken into account within the existing building energy benchmarks. In addition, the existing building energy benchmarks are not able to assist decision-makers with HVAC&R system selection. This study attempts to overcome these two deficiencies through the performance characterisation of 36 HVAC&R systems based on the simultaneous dynamic simulation of a building and a variety of HVAC&R systems using TRNSYS software. To characterise the performance of HVAC&R systems, four criteria are considered; energy consumption, CO2 emissions, thermal comfort and indoor air quality. The results of the simulations show that, all the studied systems are able to provide an acceptable level of indoor air quality and thermal comfort. However, the energy consumption and amount of CO2 emissions vary. One of the significant outcomes of this study reveals that combined heating, cooling and power systems (CCHP) have the highest energy consumption with the lowest energy related CO2 emissions among the studied HVAC&R systems.

Electricity use in the commercial kitchen

Academic and industrial literature concerning the energy consumption of commercial kitchens is scarce. Electricity consumption data were collected from distribution board current transformers in a sample of fourteen UK public house restaurants. This was set up to identify patterns of appliance use as well as to assess the total energy consumption of these establishments. The electricity consumption in the selected commercial kitchens was significantly higher than current literature estimates. On average, 63% of the premises electricity consumption was attributed to the catering activity. Key appliances that contributed to the samples average electricity consumption were identified as refrigeration (70 kwh, 41%), fryers (11 kwh, 13%), combi-ovens (35 kwh, 12%) bain maries (27 kwh, 9%) and grills (37kwh, 12%). Behavioral factors and poor maintenance were identified as major contributors to excessive electricity usage with potential savings of 70% and 45% respectively. Initiatives are required to influence operator behavior, such as the expansion of mandatory energy labeling, improved feedback information and the use of behavior change campaigns. Strict maintenance protocols and more appropriate sizing of refrigeration would be of great benefit to energy reduction.

Made in Italy. Made in Britain. Quality, brands and innovation in the European poultry market, 1950-1980.

This paper compares the development of the poultry industry in Italy with the UK. Earlier research has suggested that the UK poultry industry developed a symbiotic relationship with the emerging supermarket retailers. Italy had a retarded supermarket sector. Its distribution system favoured small-scale, independent butchers rather than chains of self-service supermarkets. Despite this the Italian poultry industry also modernised, adopting US technologies. The catalyst for this modernisation was technological innovation in refrigeration technologies that enabled Italian consumers and independent retailers to be persuaded of the merits of the new ‘technological’ chicken. While the Italian market has become dominated by AIA and Amadori in recent years, the key innovators were the entrepreneurs that created the company called Arena.

Electricity use in the commercial kitchen

Academic and industrial literature concerning the energy use of commercial kitchens is scarce. Electricity consumption data were collected from distribution board current transformers in a sample of fourteen UK public house-restaurants. This was set up to identify patterns of appliance use as well as to assess the total energy consumption of these establishments. The electricity consumption in the selected commercial kitchens was significantly higher than current literature estimates. On average, 63% of the premises’ electricity consumption was attributed to the catering activity. Key appliances that contributed to the samples average daily electricity consumption of the kitchen were identified as refrigeration (70 kWh, 41%), fryers (11 kWh, 13%), combination ovens (35 kWh, 12%), bain maries (27 kWh, 9%) and grills (37 kWh, 12%). Behavioural factors and poor maintenance were identified as major contributors to excessive electricity usage with potential savings of 70% and 45% respectively. Initiatives are required to influence operator behaviour, such as the expansion of mandatory energy labelling, improved feedback information and the use of behaviour change campaigns. Strict maintenance protocols and more appropriate sizing of refrigeration would be of great benefit to energy reduction.

View of drafting section in Air Conditioning Department of the New York Trade School

Students are shown working in the drafting section of the Air Conditioning Department of the New York Trade School. Black and white photograph that has some damage around the edges.

Automotive Classroom at the New York Trade School

Black and white photograph of an empty classroom of the Automotive Department at the New York Trade School.

Interface entre arquitetura bioclimática e decisões projetuais

This research has as its object study focus bioclimatic in architecture and its conection with projects decisions, on what regards to environmental comfort for single-family dwelling. From the analysis of five architectural projects inserted in Natal/RN, warm-moist weather, this research gather informations regarding architectural features guided by shape and space arrengement, which embody important elements for the project design development. Computer simulations assisted as foundation to verify the efficiency grade for these projects strategies from shading analysis. Related strategies for the demands of natural ventilation circulation and thermal mass for refrigeration were analysed as well. Results show that there is an hierarchizing of priorities for the decisions made when it comes to shape and space disposition variables, as well as the way these variables will consider the bioclimatic demands. The analysis, even, show that there is no single way to respond to specific bioclimatic demands, as it points out the value of examination of the projectual solutions throughtout the conception process, in order to achieve an efficient project performance for the envimonment comfort

Construção, caracterização e aplicação de eletrodos para descarga por arco de cátodo oco

The system built to characterize electrodes and, consequently, deposited fine films are constituted by a hollow cathode that works to discharges and low pressures (approximately 10-3 to 5 mbar), a source DC (0 to 1200 V), a cylindrical camera of closed borossilicato for flanges of stainless steel with an association of vacuum bombs mechanical and spread. In the upper flange it is connected the system of hollow cathode, which possesses an entrance of gas and two entrances for its refrigeration, the same is electrically isolated of the rest of the equipment and it is polarized negatively. In front of the system of hollow cathode there is a movable sample in stainless steel with possibility of moving in the horizontal and vertical. In the vertical, the sample can vary its distance between 0 and 70 mm and, in the horizontal, can leave completely from the front of the hollow cathode. The sample and also the cathode hollow are equipped with cromel-alumel termopares with simultaneous reading of the temperatures during the time of treatment. In this work copper electrodes, bronze, titanium, iron, stainless steel, powder of titanium, powder of titanium and silício, glass and ceramic were used. The electrodes were investigated relating their geometry change and behavior of the plasma of the cavity of hollow cathode and channel of the gas. As the cavity of hollow cathode, the analyzed aspects were the diameter and depth. With the channel of the gas, we verified the diameter. In the two situations, we investigated parameters as flow of the gas, pressure, current and applied tension in the electrode, temperature, loss of mass of the electrode with relationship at the time of use. The flow of gas investigated in the electrodes it was fastened in a work strip from 15 to 6 sccm, the constant pressure of work was among 2.7 to 8 x 10-2 mbar. The applied current was among a strip of work from 0,8 to 0,4 A, and their respective tensions were in a strip from 400 to 220 V. Fixing the value of the current, it was possible to lift the curve of the behavior of the tension with the time of use. That curves esteem in that time of use of the electrode to its efficiency is maximum. The temperatures of the electrodes were in the dependence of that curves showing a maximum temperature when the tension was maximum, yet the measured temperatures in the samples showed to be sensitive the variation of the temperature in the electrodes. An accompaniment of the loss of mass of the electrode relating to its time of use showed that the electrodes that appeared the spherical cavities lost more mass in comparison with the electrodes in that didn't appear. That phenomenon is only seen for pressures of 10-2 mbar, in these conditions a plasma column is formed inside of the channel of the gas and in certain points it is concentrated in form of spheres. Those spherical cavities develop inside of the channel of the gas spreading during the whole extension of the channel of the gas. The used electrodes were cut after they could not be more used, however among those electrodes, films that were deposited in alternate times and the electrodes that were used to deposit films in same times, those films were deposited in the glass substrata, alumina, stainless steel 420, stainless steel 316, silício and steel M2. As the eletros used to deposit films in alternate time as the ones that they were used to deposit in same times, the behavior of the thickness of the film obeyed the curve of the tension with relationship the time of use of the electrode, that is, when the tension was maximum, the thickness of the film was also maximum and when the tension was minimum, the thickness was minimum and in the case where the value of the tension was constant, the thickness of the film tends to be constant. The fine films that were produced they had applications with nano stick, bio-compatibility, cellular growth, inhibition of bacterias, cut tool, metallic leagues, brasagem, pineapple fiber and ornamental. In those films it was investigated the thickness, the adherence and the uniformity characterized by sweeping electronic microscopy. Another technique developed to assist the production and characterization of the films produced in that work was the caloteste. It uses a sphere and abrasive to mark the sample with a cap impression, with that cap form it is possible to calculate the thickness of the film. Through the time of life of the cathode, it was possible to evaluate the rate of waste of its material for the different work conditions. Values of waste rate up to 3,2 x 10-6 g/s were verified. For a distance of the substratum of 11 mm, the deposited film was limited to a circular area of 22 mm diameter mm for high pressures and a circular area of 75 mm for pressure strip. The obtained films presented thickness around 2,1 µm, showing that the discharge of arch of hollow cathode in argon obeys a curve characteristic of the tension with the time of life of the eletrodo. The deposition rate obtained in this system it is of approximately 0,18 µm/min

Estudo comparativo da variação temporal da comunidade fitoplanctônica do açude Cruzeta inserido no bioma caatinga, Rio Grande do Norte

The Cruzeta impoundment, situated in the city of Cruzeta, hinterland of the state of the Rio Grande do Norte state has significant importance to the municipality as it represents the only source of supplying water to the region. It was hypothesized that the regional consequence of the global warming and the warming of surface water could substantially contribute the significant growth of the aquatic macrophytes in the years 2008-2009. The growth of these vegetation believed to be improved the degree of water transparency and as a consequence of the improved growth of phytoplankton species and chlorophyll biomass. At the same time the aquatic macrophyte could interact and compete potentially for the dissolved inorganic nutrients resources and the phytoplankton community. This study presents a comparison of years 2004-2005 when it did not have the expressive presence of the aquatic macrophyte community or restricted to the littoral region. In contrast, the years 2008-2009 showed a significant growth of the aquatic macrophyte in the Cruzeta/RN impoundments. The present study is an attempt to elucidate the significant presence of the aquatic macrophyte, Eichhornia crassipes, Ceratophyllum submersum, Nymphea sp and Pistia sp, and its interference on the ecology of phytoplankton. The samplings had been carried out from September of 2008 to April of 2009 and consistently between 10:00 h and 12:00 h with the aid of Van Dorn bottle and the plankton net of mesh size 20 Qm. The collections were made in three depths ie., surface, mid-column and bottom. The Physical-Chemical parameters such as pH, temperature, electrical conductivity and dissolved oxygen had been analyzed in situ. The samples for analysis of nutrients and chlorophyll were kept under refrigeration for posterior analysis in the laboratory. Phytoplankton samples were preserved in Lugol-iodine and kept for sedimentation for quali-quantitative analysis of phytoplankton. Enumeration of cells, colonies and filaments was done with the aid of Sedgwick-Rafter counting chamber and expressed as numbers/ml. Chlorophyll a was analyzed as a functional component of phytoplankton biomass and extracted with cold 90% acetone. The results indicate that the chlorophyll concentration varied between 5,65-8,08 Qg.L-1 for the dry period and 5,09-6,23 Qg.L-1 for the rainy period and showed considerable reduction when compared to the values to the 2004-2005 study period. The temperature was always presented higher in relation to the 2004-2005 study. Phytoplankton species showed a relative abundance of the Cyanophyceae for both the period of dry and rainy. The predominance species are filamentous Leptolymbya geophila Borzi (Planctolyngbya sp), Anabaena plankctônica Brunnthaler, Oscillatória limosa Ag. and Cylindrospermopsis raciborskii (Wolosz). The concentration of the nutrients such as nitrate and orto-phosfato had always presented higher values during the rainy period and the ammoniacal nitrogen retained moderate values in the dry period and a slight increase in rainy season. The main conclusions are the reduction of the concentration of chlorophyll, diversity of phytoplankton, and the increase in temperature and transparency of the water during the period of the study

QUANTIFICAÇÃO DE AÇÚCARES em PÊSSEGOS da VARIEDADE BIUTI, ARMAZENADOS SOB CONDIÇÕES DE AMBIENTE E REFRIGERAÇÃO

O objetivo deste trabalho foi identificar e quantificar os açúcares em frutos de pessegueiro da variedade 'Biuti', armazenados sob condições de ambiente (27,3ºC; 70% UR) e sob refrigeração (4ºC; 90%), comparar as diferenças entre os teores de açúcares nas duas condições de armazenamento. A identificação e a quantificação precisa dos açúcares (glicose, frutose e sacarose) foi realizada por cromatografia em fase líquida HPLC. Verificou-se que a sacarose foi o açúcar encontrado em maior quantidade, sendo verificado apenas traços de glicose e frutose em alguns frutos. Sob condições ambientais, os teores de sacarose do 3º até o 9º dia de armazenamento não diferiram significativamente entre si; entretanto, no 12º dia, os frutos obtiveram baixos teores de sacarose, pois os mesmos já estavam em processo de senescência. Sob refrigeração, o aumento nos teores de açúcares dos frutos ocorreu gradativamente durante todo o armazenamento, e ao final do mesmo, verificaram-se os maiores teores de sacarose, frutose e glicose, os quais eram mais elevados do que os encontrados nos frutos armazenados sob condições ambientais.

Estabilidade do antígeno de célula total de Brucella abortus para uso no diagnóstico sorológico da brucelose bovina pela reação de fixação de complemento

A reação de fixação de complemento é um dos testes usados no diagnóstico confirmatório da brucelose bovina, e para sua realização emprega-se o mesmo antígeno usado na prova de soroaglutinação lenta, porém não foi possível encontrar na literatura estudos sobre a estabilidade desse antígeno para uso na prova de fixação de complemento, de modo a estabelecer um prazo de validade para o mesmo. Por isso, esta investigação teve por objetivo avaliar a estabilidade do antígeno de célula total de Brucella conservado sob refrigeração, para uso na reação de fixação de complemento. Analisaram-se 14 partidas de antígeno, preparado com Brucella abortus amostra 1119/3 e padronizado para uso na prova de soroaglutinação lenta, com tempo de fabricação variando de 9 meses a 23 anos e 11 meses. Testaram-se 167 soros bovinos com títulos variáveis de anticorpos contra Brucella, adotando-se a técnica com incubação a 37ºC nas duas fases da reação e 5 unidades hemolíticas 50% de complemento. Considerou-se como positivo o soro com pelo menos 25% de fixação de complemento na diluição 1:4. Compararam-se os resultados obtidos com as 13 partidas de antígeno com aqueles obtidos com a partida com 9 meses de fabricação, usando o teste de chi2 de McNemar e o coeficiente kappa. A grande maioria dos soros apresentou resultados muito próximos quando testados com as diversas partidas de antígeno, e não se observou relação entre tempo de fabricação do antígeno e diferenças nos resultados obtidos.

Postharvest Conservation of Mature-Green and Ripe 'Paluma' Guava Stored at Two Temperatures

This work aimed to establish the importance of maturation and ripeness stages and the use of refrigeration for the conservation of 'Paluma' guavas. Fruit picked at the mature-green and ripe stages were stored at ambient conditions (21 degrees C and 85% RH) and also at 10 degrees C (85% RH). The fruit were evaluated every 2 or 3 days for weight loss, appearance, decay, color, firmness, soluble solids, titratable acidity, ascorbic acid, total polyphenols extractable content and total antioxidant activity. The fruit stored at 21 degrees C had higher weight loss than those stored at 10 degrees C. Mature-green guavas at 21 degrees C remained in good quality for 6 days, but at 10 degrees C, the preservation period increased to 15 days. Ripe fruit were preserved for 4 days at 21 degrees C, which was extended with refrigeration to 6 days. Mature-green fruit at 21 degrees C had decay in 6 days; while at 10 degrees C decay happened in 18 days. The peel color of mature-green fruits, at 21 degrees C, showed increasing values of luminosity, indicating that its color became lighter (change from green to yellow) and at 10 degrees C it showed constant values until the end of storage. Pulp firmness of mature-green fruit declined during storage as a result of ripening. In ripe fruits such reduction occurred more slowly, since they were softer. The color of the pulp became intense red for mature fruits. Soluble solids were lower in ripe fruit at 21 degrees C, while in mature fruits at 10 degrees C, it increased. The titratable acidity increased in fruits stored at 10 degrees C. The fruits kept at 21 degrees C and the mature guavas kept at 10 degrees C showed no changes in ascorbic acid content. The ripe fruit at 10 degrees C maintained their ascorbic acid levels. Mature guavas, stored at 10 degrees C, had the longest shelf life and higher contents of soluble solids and titratable acidity, with no changes in total polyphenols extractable content and total antioxidant activity.

Chilling Injury in Avocados and Its Prevention with Thermal Treatment

The combinations of temperature and time which can cause chilling injuries in avocados 'Geada', 'Quintal' and 'Fortuna' were determined. The binomial 4 degrees C/ 28 days was selected to determine the activity of peroxidase (POD), polyphenoloxidase (PPO), polygalacturonase (PG) and methylesterase pectin (PME). The respiratory activity was also evaluated. The fruits were stored at this condition until being transferred to ambient conditions (22 degrees C and 77% RH) until maturity, when they were compared to fruits stored permanently at this environment, after being cleaned (control). In the second part of this work, different hydrothermal treatments were tested to prevent or minimize chilling injuries. Avocados 'Geada', 'Quintal' and 'Fortuna' were treated at 38 degrees C for 0, 30, 60 and 90 minutes before storage at 4 degrees C for 28 days. It was observed that the activity of enzymes associated to browning, POD and PPO, and to maturation, PG and PME, had become greater in fruits stored at 4 degrees C, or when they were transferred to environmental conditions. Fruits subjected to refrigeration, after transferred to environment, presented lower respiratory peak intensity and it occurred earlier than the others. Treatments using 38 degrees C for 60 and 90 min minimized the symptoms of chilling injury in avocados 'Geada' while for 'Quintal' the most efficient was 38 degrees C for 60 min. In 'Fortuna' these treatments did not minimize the damage by cold.

Avaliação física e química de produtos minimamente processados de abacaxi-'Pérola'

O objetivo deste trabalho foi avaliar, física e quimicamente, produtos minimamente processados de abacaxi-'Pérola', rodelas e metades, armazenados sob diferentes temperaturas (3ºC, 6ºC e 9ºC). Frutos selecionados, quanto ao grau de maturação e ausência de danos, foram lavados, desinfeccionados com cloro (200 mg.L-1) e armazenados a 10ºC, por 12 horas, antes do processamento. O produto minimamente processado foi embalado em bandejas de isopor recobertas com filme de PVC esticável (metades) ou bandejas de tereftalato de polietileno (rodelas) e armazenado sob refrigeraç ;ão, com avaliação a cada 3 dias, quanto à textura, coloração, pH, e conteúdos de sólidos solúveis totais, acidez total titulável, ácido ascórbico e de açúcares, solúveis e redutores. Durante o armazenamento, o produto tornou-se menos firme, e sua polpa apresentou escurecimento. Os conteúdos de açúcares solúveis e redutores e de sólidos solúveis totais não foram afetados pelo tipo de preparo, temperatura ou embalagem. Os teores de acidez total titulável aumentaram e foram influenciados pela temperatura, sendo que os mantidos a 9ºC apresentaram os maiores teores, havendo, como conseqüência, decréscimo no pH. Os produtos armazenados a 9ºC também apresentaram evolução mais rápida no escurecimento, na redução do teor de ácido ascórbico e menor vida útil (6 dias), enquanto, para os armazenados a 3ºC e 6ºC, este período foi de 9 dias. Os resultados obtidos permitiram concluir que a temperatura de armazenamento foi o fator limitante para a vida útil destes produtos.