Optical fiber long-period grating with solgel coating for gas sensor

The novel long-period fiber grating (LPFG) film sensor is composed of the long-period grating coated with solgel-derived sensitive films. The characteristics of the transmissivity of the LPFG film sensor are studied. By analyzing the relation among the sensitivity S-n, the thin film optical parameters, and the fiber grating parameters, the optimal design parameters of the LPFG film sensor are obtained. Data simulation shows that the resolution of the refractive index of this LPFG film sensor is predicted to be 10(-8). Experimentally, a LPFG film sensor for detection Of C2H5OH was fabricated, and a preliminary gas-sensing test was performed. (c) 2006 Optical Society of America.

Design of anisotropic reflector with birefringent thin films

A novel design for dielectric anisotropic mirrors with birefringent thin films for normal incidence is presented. This mirror consists of a stack of quarter-wave biaxial layers. The biaxial anisotropic layers can be fabricated by oblique deposition. The reflectance is different for two linear polarizations of light incidence on the mirrors. As a numerical example, the design is carried out on glass with TiO2 and ZrO2. These thin films could be applied to anisotropic reflective devices for lasers.

Análise de critérios de dimensionamento de carga em dutos de concreto instalados em vala na situação de recobrimento mínimo.

Perante diversas situações da engenharia são utilizadas formulações empíricas de dimensionamento baseadas em dados de campo e experiência profissional que definem muito o caráter subjetivo da metodologia padrão de projeto. O presente trabalho de pesquisa aborda os diversos métodos de obtenção dos esforços gerados em dutos enterrados submetidos a cargas dinâmicas e estáticas e sua posterior reavaliação através de modelagem numérica com o programa Plaxis 3D. Os métodos analíticos não convencionais foram comparados com o método padrão de cálculo sendo que o mesmo demonstrou ter uma boa precisão mesmo sem considerar outros fatores importantes como a parcela de resistência devida à coesão do solo e sua deformabilidade. A modelagem numérica demonstrou o conservadorismo do método de Marston e o subdmensionamento do espraiamento em prisma devido aos efeitos locais ocasionados pela adoção do recobrimento mínimo e sobrecarga dinâmica elevada. Também se observou, através da modelagem 3D, que a utilização dos dois métodos clássicos favorecem a obtenção de resultados dentro da razoabilidade.Verificou-se também, como resultado desta pesquisa, que a proposta de um método clássico modificado permite uma melhor aproximação da carga que atinge o duto.

Articulated wooden blades for a horizontal-axis wind turbine. Design, construction and testing.

A pair of blades were constructed following a Tapered Chord, Zero Twist pattern after Anderson. The construction uses the Wood Epoxy Saturation Technique, with a solid Beech main spar and leading edge joined together with laminated veneers of beech forming a D-section; the trailing edge is formed from millimetre ply skins, foam filled to resist compressive loads. This construction leads to an extremely light, flexible blade, with the centres of gravity and torsion well forward, giving good stability. Each blade has three built-in strain gauges, alowing flapwise bending to be measured. Stiffness, and natural frequencies, were measured, to input to a numerical computer model to calculate blade deformation during operation, and to determine stability boundaries of the blade. Preliminary aerodynamic performance measurements are presented and close agreement is found with theory.

CLADP: THE CAMBRIDGE LINEAR ANALYSIS AND DESIGN PROGRAMS.

An interactive software facility for designing multivariable control systems is described. The paper discusses the desirable characteristics of such a facility, the particular capabilities of CLADP and the numerical algorithms which lie behind them.

NUMERICAL STUDY OF THE 3D FLOWFIELD IN A TRANSONIC COMPRESSOR ROTOR WITH A MODELLING OF THE TIP CLEARANCE FLOW.

This paper describes a computer code aimed at solving the equations of three dimensional viscous compressible flow in turbomachine geometries. The code is applied to the study of the flowfield in a transonic axial compressor rotor at design speed at both maximum flow and towards stall. The predicted flowfield is compared with the laser measurements and the performance of the code discussed. In addition the discussion highlights the change in the predicted endwall and tip clearance flows as the rotor operating point is moved towards stall.

Numerical modelling of dynamic response of loss modulated monolithic multisection mode-locked semiconductor lasers

Monolithic multisection mode-locked semiconductor lasers with an integrated distributed Bragg reflector (DBR) have recently been demonstrated to generate stable picosecond pulses at high repetition rates suitable for optical communication systems. However, there has been very little theoretical work on understanding the physical mechanisms of the device and on optimisation of the absorber modulator design. This article presents numerical modeling of the loss modulated mode-locking process in these lasers. The model predicts most aspects experimentally observed within this type of device, and the results show the output waveform, optical spectrum, instantaneous frequency chirp, and stable operating range.

The use of object oriented modelling and simulation tools in constraint satisfaction for embodiment design

The software package Dymola, which implements the new, vendor-independent standard modelling language Modelica, exemplifies the emerging generation of object-oriented modelling and simulation tools. This paper shows how, in addition to its simulation capabilities, it may be used as an embodiment design tool, to size automatically a design assembled from a library of generic parametric components. The example used is a miniature model aircraft diesel engine. To this end, the component classes contain extra algebraic equations calculating the overload factor (or its reciprocal, the safety factor) for all the different modes of failure, such as buckling or tensile yield. Thus the simulation results contain the maximum overload or minimum safety factor for each failure mode along with the critical instant and the device state at which it occurs. The Dymola "Initial Conditions Calculation" function, controlled by a simple software script, may then be used to perform automatic component sizing. Each component is minimised in mass, subject to a chosen safety factor against failure, over a given operating cycle. Whilst the example is in the realm of mechanical design, it must be emphasised that the approach is equally applicable to the electrical or mechatronic domains, indeed to any design problem requiring numerical constraint satisfaction.

RANS-URANS in axial compressor, a design methodology

Turbomachinery flows are inherently unsteady. Until now during the design process, unsteadiness has been neglected, with resort merely to steady numerical simulations. Despite the assumption involved, the results obtained with steady simulations have been used with success. One of the questions arising in recent years is can unsteady simulations be used to improve the design of turbomachines? In this work the numerical simulation of a multi-stage axial compressor is carried out. Comparison of Reynolds averaged Navier-Stokes (RANS) and unsteady Reynolds averaged Navier-Stokes (URANS) calculation shows that the unsteadiness affects pressure losses and the prediction of stall limit. The unsteady inflow due to the wake passing mainly modifies the losses and whirl angle near the endwalls. The computational cost of the fully unsteady compared with a steady simulation is about four times in terms of mesh dimension and two orders of magnitude as number of iterations. A mixed RANS-URANS solution has been proposed to give the designer the possibility to simulate an unsteady stage embedded in a steady-state simulation. This method has been applied to the simulation of a four-stage axial compressor rig. The mixed RANS-URANS approach has been developed using sliding and mixing planes as interface conditions. The rotor-stator interaction has been captured physically while reducing the computational time and mesh size.

Towards the development of an integrated design framework using the Blackboard model

Current research into the process of engineering design is extending the use of computers towards the acquisition, representation and application of design process knowledge in addition to the existing storage and manipulation of product-based models of design objects. This is a difficult task because the design of mechanical systems is a complex, often unpredictable process involving ill-structured problem solving skills and large amounts of knowledge, some which may be of an incomplete and subjective nature. Design problems require the integration of a variety of modes of working such as numerical, graphical, algorithmic or heuristic and demand products through synthesis, analysis and evaluation activities.

This report presents the results of a feasibility study into the blackboard approach and discusses the development of an initial prototype system that will enable an alphanumeric design dialogue between a designer and an expert to be analysed in a formal way, thus providing real-life protocol data on which to base the blackboard message structures.

Design and optimization of a 250nm SOI LDMOSFET

This work is aimed at optimising the static performance of a high voltage SOI LDMOSFET. Starting with a conventional LDMOSFET, 2D and 3D numerical simulation models, able to accurately match datasheet values, have been developed. Moving from the original device, several design techniques have been investigated with the target of improving the breakdown voltage and the ON-state resistance. The considered design techniques are based on the modification of the doping profile of the drift region and the Superjunction design technique. The paper shows that a single step doping within the drift region is the best design choice for the considered device and is found to give a 24% improvement in the breakdown voltage and a 17% reduction of the ON-state resistance. © 2011 IEEE.

Design of carbon nanotube fiber microelectrode for glucose biosensing

BACKGROUND: Carbon nanotube (CNT) fiber directly spun from an aerogel has a unique, well-aligned nanostructure (nano-pore and nano-brush), and thus provides high electro-catalytic activity and strong interaction with glucose oxidase enzyme. It shows great potential as a microelectrode for electrochemical biosensors. RESULTS: Cyclic voltammogram results indicate that post-synthesis treatments have great influence on the electrocatalytic activity of CNT fibers. Raman spectroscopy and electrical conductivity tests suggest that fibers annealed at 250 °C remove most of the impurities without damaging the graphite-like structure. This leads to a nano-porous morphology on the surface and the highest conductivity value (1.1 × 10 5 S m -1). Two CNT fiber microelectrode designs were applied to enhance their electron transfer behaviour, and it was found that a design using a 30 nm gold coating is able to linearly cover human physiological glucose level between 2 and 30 mmol L -1. The design also leads to a low detection limit of 25 μmol L -1. CONCLUSIONS: The high performance of CNT fibers not only offers exceptional mechanical and electrical properties, but also provides a large surface area and electron transfer pathway. They consequently make excellent bioactive microelectrodes for glucose biosensing, especially for potential use in implantable devices. © 2011 Society of Chemical Industry.

A matrix-calculation-based algorithm for numerical change propagation analysis

Engineering changes (ECs) are raised throughout the lifecycle of engineering products. A single change to one component produces knock-on effects on others necessitating additional changes. This change propagation significantly affects the development time and cost and determines the product's success. Predicting and managing such ECs is, thus, essential to companies. Some prediction tools model change propagation by algorithms, whereof a subgroup is numerical. Current numerical change propagation algorithms either do not account for the exclusion of cyclic propagation paths or are based on exhaustive searching methods. This paper presents a new matrix-calculation-based algorithm which can be applied directly to a numerical product model to analyze change propagation and support change prediction. The algorithm applies matrix multiplications on mutations of a given design structure matrix accounting for the exclusion of self-dependences and cyclic propagation paths and delivers the same results as the exhaustive search-based Trail Counting algorithm. Despite its factorial time complexity, the algorithm proves advantageous because of its straightforward matrix-based calculations which avoid exhaustive searching. Thereby, the algorithm can be implemented in established numerical programs such as Microsoft Excel which promise a wider application of the tools within and across companies along with better familiarity, usability, practicality, security, and robustness. © 1988-2012 IEEE.