Peak -to -average power ratio reduced parallel interference cancellation Multicarrier-Code Division Multiple Access system with anti -interference property

Orthogonal Frequency-Division Multiplexing (OFDM) has been proved to be a promising technology that enables the transmission of higher data rate. Multicarrier Code-Division Multiple Access (MC-CDMA) is a transmission technique which combines the advantages of both OFDM and Code-Division Multiplexing Access (CDMA), so as to allow high transmission rates over severe time-dispersive multi-path channels without the need of a complex receiver implementation. Also MC-CDMA exploits frequency diversity via the different subcarriers, and therefore allows the high code rates systems to achieve good Bit Error Rate (BER) performances. Furthermore, the spreading in the frequency domain makes the time synchronization requirement much lower than traditional direct sequence CDMA schemes. There are still some problems when we use MC-CDMA. One is the high Peak-to-Average Power Ratio (PAPR) of the transmit signal. High PAPR leads to nonlinear distortion of the amplifier and results in inter-carrier self-interference plus out-of-band radiation. On the other hand, suppressing the Multiple Access Interference (MAI) is another crucial problem in the MC-CDMA system. Imperfect cross-correlation characteristics of the spreading codes and the multipath fading destroy the orthogonality among the users, and then cause MAI, which produces serious BER degradation in the system. Moreover, in uplink system the received signals at a base station are always asynchronous. This also destroys the orthogonality among the users, and hence, generates MAI which degrades the system performance. Besides those two problems, the interference should always be considered seriously for any communication system. In this dissertation, we design a novel MC-CDMA system, which has low PAPR and mitigated MAI. The new Semi-blind channel estimation and multi-user data detection based on Parallel Interference Cancellation (PIC) have been applied in the system. The Low Density Parity Codes (LDPC) has also been introduced into the system to improve the performance. Different interference models are analyzed in multi-carrier communication systems and then the effective interference suppression for MC-CDMA systems is employed in this dissertation. The experimental results indicate that our system not only significantly reduces the PAPR and MAI but also effectively suppresses the outside interference with low complexity. Finally, we present a practical cognitive application of the proposed system over the software defined radio platform.

Peak-to-Average Power Ratio Reduced Parallel Interference Cancellation Multicarrier-Code Division Multiple Access System with Anti-Interference Property

Orthogonal Frequency-Division Multiplexing (OFDM) has been proved to be a promising technology that enables the transmission of higher data rate. Multicarrier Code-Division Multiple Access (MC-CDMA) is a transmission technique which combines the advantages of both OFDM and Code-Division Multiplexing Access (CDMA), so as to allow high transmission rates over severe time-dispersive multi-path channels without the need of a complex receiver implementation. Also MC-CDMA exploits frequency diversity via the different subcarriers, and therefore allows the high code rates systems to achieve good Bit Error Rate (BER) performances. Furthermore, the spreading in the frequency domain makes the time synchronization requirement much lower than traditional direct sequence CDMA schemes. There are still some problems when we use MC-CDMA. One is the high Peak-to-Average Power Ratio (PAPR) of the transmit signal. High PAPR leads to nonlinear distortion of the amplifier and results in inter-carrier self-interference plus out-of-band radiation. On the other hand, suppressing the Multiple Access Interference (MAI) is another crucial problem in the MC-CDMA system. Imperfect cross-correlation characteristics of the spreading codes and the multipath fading destroy the orthogonality among the users, and then cause MAI, which produces serious BER degradation in the system. Moreover, in uplink system the received signals at a base station are always asynchronous. This also destroys the orthogonality among the users, and hence, generates MAI which degrades the system performance. Besides those two problems, the interference should always be considered seriously for any communication system. In this dissertation, we design a novel MC-CDMA system, which has low PAPR and mitigated MAI. The new Semi-blind channel estimation and multi-user data detection based on Parallel Interference Cancellation (PIC) have been applied in the system. The Low Density Parity Codes (LDPC) has also been introduced into the system to improve the performance. Different interference models are analyzed in multi-carrier communication systems and then the effective interference suppression for MC-CDMA systems is employed in this dissertation. The experimental results indicate that our system not only significantly reduces the PAPR and MAI but also effectively suppresses the outside interference with low complexity. Finally, we present a practical cognitive application of the proposed system over the software defined radio platform.

Técnicas de conformação de feixe em arranjo de antenas utilizando aprendizagem por reforço

Beamforming is a technique widely used in various fields. With the aid of an antenna array, the beamforming aims to minimize the contribution of unknown interferents directions, while capturing the desired signal in a given direction. In this thesis are proposed beamforming techniques using Reinforcement Learning (RL) through the Q-Learning algorithm in antennas array. One proposal is to use RL to find the optimal policy selection between the beamforming (BF) and power control (PC) in order to better leverage the individual characteristics of each of them for a certain amount of Signal to Interference plus noise Ration (SINR). Another proposal is to use RL to determine the optimal policy between blind beamforming algorithm of CMA (Constant Modulus Algorithm) and DD (Decision Direct) in multipath environments. Results from simulations showed that the RL technique could be effective in achieving na optimal of switching between different techniques.

Cooperative routing for collision minimization in wireless sensor networks

Cooperative communication has gained much interest due to its ability to exploit the broadcasting nature of the wireless medium to mitigate multipath fading. There has been considerable amount of research on how cooperative transmission can improve the performance of the network by focusing on the physical layer issues. During the past few years, the researchers have started to take into consideration cooperative transmission in routing and there has been a growing interest in designing and evaluating cooperative routing protocols. Most of the existing cooperative routing algorithms are designed to reduce the energy consumption; however, packet collision minimization using cooperative routing has not been addressed yet. This dissertation presents an optimization framework to minimize collision probability using cooperative routing in wireless sensor networks. More specifically, we develop a mathematical model and formulate the problem as a large-scale Mixed Integer Non-Linear Programming problem. We also propose a solution based on the branch and bound algorithm augmented with reducing the search space (branch and bound space reduction). The proposed strategy builds up the optimal routes from each source to the sink node by providing the best set of hops in each route, the best set of relays, and the optimal power allocation for the cooperative transmission links. To reduce the computational complexity, we propose two near optimal cooperative routing algorithms. In the first near optimal algorithm, we solve the problem by decoupling the optimal power allocation scheme from optimal route selection. Therefore, the problem is formulated by an Integer Non-Linear Programming, which is solved using a branch and bound space reduced method. In the second near optimal algorithm, the cooperative routing problem is solved by decoupling the transmission power and the relay node se- lection from the route selection. After solving the routing problems, the power allocation is applied in the selected route. Simulation results show the algorithms can significantly reduce the collision probability compared with existing cooperative routing schemes.

Extensões na arquitetura SDN para o provisionamento de QoS através do monitoramento e uso de múltiplos caminhos

The substantial increase in the number of applications offered through the computer networks, as well as in the volume of traffic forwarded through the network, have hampered to assure adequate service level to users. The Quality of Service (QoS) offer, honoring specified parameters in Service Level Agreements (SLA), established between the service providers and their clients, composes a traditional and extensive computer networks’ research area. Several schemes proposals for the provision of QoS were presented in the last three decades, but the acting scope of these proposals is always limited due to some factors, including the limited development of the network hardware and software, generally belonging to a single manufacturer. The advent of Software Defined Networking (SDN), along with the maturation of its main materialization, the OpenFlow protocol, allowed the decoupling between network hardware and software, through an architecture which provides a control plane and a data plane. This eases the computer networks scenario, allowing that new abstractions are applied in the hardware composing the data plane, through the development of new software pieces which are executed in the control plane. This dissertation investigates the QoS offer through the use and extension of the SDN architecture. Based on the proposal of two new modules, one to perform the data plane monitoring, SDNMon, and the second, MP-ROUTING, developed to determine the use of multiple paths in the forwarding of data referring to a flow, we demonstrated in this work that some QoS metrics specified in the SLAs, such as bandwidth, can be honored. Both modules were implemented and evaluated through a prototype. The evaluation results referring to several aspects of both proposed modules are presented in this dissertation, showing the obtained accuracy of the monitoring module SDNMon and the QoS gains due to the utilization of multiple paths defined by the MP-Routing, when forwarding data flow through the SDN.

A Synthesis-free Directional Modulation Transmitter using Retrodirective Array

By modification of the classical retrodirective arrays (RDAs) architecture a directional modulation (DM) transmitter can be realized without the need for synthesis. Importantly, through analytical analysis and exemplar simulations, it is proved that, besides the conventional DM application scenario, i.e., secure transmission to one legitimate receiver located along one spatial direction in free space, the proposed synthesis-free DM transmitter should also perform well for systems where there are more than one legitimate receivers positioned along different directions in free space, and where one or more legitimate receivers exist in a multipath environment. None of these have ever been achieved before using synthesis-free DM arrangements.

Full-Duplex Spectrum Sharing in Cooperative Single Carrier Systems

We propose cyclic prefix single carrier full-duplex transmission in amplify-and-forward cooperative spectrum sharing networks to achieve multipath diversity and full-duplex spectral efficiency. Integrating full-duplex transmission into cooperative spectrum sharing systems results in two intrinsic problems: 1) the residual loop interference occurs between the transmit and the receive antennas at the secondary relays and 2) the primary users simultaneously suffer interference from the secondary source (SS) and the secondary relays (SRs). Thus, examining the effects of residual loop interference under peak interference power constraint at the primary users and maximum transmit power constraints at the SS and the SRs is a particularly challenging problem in frequency selective fading channels. To do so, we derive and quantitatively compare the lower bounds on the outage probability and the corresponding asymptotic outage probability for max–min relay selection, partial relay selection, and maximum interference relay selection policies in frequency selective fading channels. To facilitate comparison, we provide the corresponding analysis for half-duplex. Our results show two complementary regions, named as the signal-to-noise ratio (SNR) dominant region and the residual loop interference dominant region, where the multipath diversity and spatial diversity can be achievable only in the SNR dominant region, however the diversity gain collapses to zero in the residual loop interference dominant region.

Experimental Study on Key Generation for Physical Layer Security in Wireless Communications

This paper presents a thorough experimental study on key generation principles, i.e. temporal variation, channel reciprocity, and spatial decorrelation, via a testbed constructed by using wireless open-access research platform (WARP). It is the first comprehensive study through (i) carrying out a number of experiments in different multipath environments, including an anechoic chamber, a reverberation chamber and an indoor office environment, which represents little, rich, and moderate multipath, respectively; (ii) considering static, object moving, and mobile scenarios in these environments, which represents different levels of channel dynamicity; (iii) studying two most popular channel parameters, i.e., channel state information and received signal strength. Through results collected from over a hundred tests, this paper offers insights to the design of a secure and efficient key generation system. We show that multipath is essential and beneficial for key generation as it increases the channel randomness. We also find that the movement of users/objects can help introduce temporal variation/randomness and help users reach an agreement on the keys. This paper complements existing research by experiments constructed by a new hardware platform.

Calibrated Polarisation Tilt Angle Recovery for Wireless Communications

In this paper, we show how the polarisation state of a linearly polarised antenna can be recovered through the use of a three-term error correction model. The approach adopted is shown to be robust in situations where some multipath exists and where the sampling channels are imperfect with regard to both their amplitude and phase tracking. In particular, it has been shown that error of the measured polarisation tilt angle can be improved from 33% to 3% and below by applying the proposed calibration method. It is described how one can use a rotating dipole antenna as both the calibration standard and as the polarisation encoder, thus simplifying the physical arrangement of the transmitter. Experimental results are provided in order to show the utility of the approach, which could have a variety of applications including bandwidth conservative polarisation sub-modulation in advanced wireless communications systems.

Rilevamento satellitare di cicli in percorsi urbani

Lo scopo di questo lavoro è sperimentare l’impiego di ricevitori a basso costo per il posizionamento di cicli in ambito urbano. Questo tipo di rilievo trova ampio impiego nello studio e verifica delle funzionalità del reticolo delle piste ciclabili. Il rilievo effettuato in condizioni di scarsa visibilità verso la costellazione satellitare e in presenza di riflessioni multiple indotte da superfici verticali, quali quelle degli edifici in ambito urbano, risulta affetto da specifiche problematiche che si è cercato di affrontare nella presente tesi. In particolare si è analizzato l’effetto del “multipath”, nel posizionamento GPS, di un ciclista in movimento su percorsi caratterizzati da “canyon urbano”, nel centrostorico di Bologna. La strumentazione sperimentata è consistita da un tablet Smasung Note 10.1, uno smartphone Samsung S4 e un ricevitore GNSS (U-blox Neo-7P) collegato ad una Raspberry Pi 2. Anche a livello software è stato sperimentato per le unità Samsung sia il software Strava, che il Blackcountry Navigator. Mentre l’acquisizione del sensore U-blox è avvenuta direttamente tramite connessione seriale in un file di testo. Nel primo capitolo verrà presentato il sistema GPS nella sua generalità. Nel secondo, invece, verrà descritta la parte del sistema GPS, che si è utilizzato per questo lavoro. Nel terzo si mostreranno gli strumenti e le apparecchiature utilizzate durante il lavoro. Nel quarto si procederà alla presentazione del caso di studio. Nell’ultimo capitolo verranno riportate le conclusioni di tutto il lavoro svolto.

Höjdbestämningsmetoder vid upprättande av nybyggnadskartor : Jämförelse mellan nätverks-RTK och trigonometrisk höjdmätning

Levelling and trigonometric height measurements are the methods that are mostly used today for height determination, as the standard error with these methods is in the magnitude of millimeters, as long as the view length is less than 50 m. When creating a new construction map the requirement on standard error differ from 1 (Fredriksson, 2011) to 10 cm (www.arvidsjaur.se) depending on which municipality it concerns. When using network RTK for measuring, the accuracy in height can fall below 3 cm when the conditions are optimal. The purpose of this paper is to investigate if network RTK can be used as an alternative to determinate height when accuracy under 10 cm is requested. Five points at locations with different conditions for accuracy got their height determined with the three methods mentioned above. Positional accuracy was formed for each point and method. The result from levelling was used as reference for the calculations. To compare the result with the requirements extended standard uncertainty, 2covering 95 %, was used. The result from trigonometric height measurement shows a position accuracy of 4 mm. From the network RTK, the points that were positioned without interference got a positional accuracy of 3.3 to 5.5 cm, while the points that were influenced by their environment, multipath interference and obstructions, got a positional accuracy of 123.3 cm and 234.4 cm. Positional accuracy of this method became 127.4 cm. The result from the height determination with network RTK shows big difference in accuracy for the different points. The conclusion is that network RTK measurement would not be a sufficiently accurate height determination method for preparation of a new construction map in an area similar to the one used for this test. Conversely, a construction map drawn up in an open area free from interference obstacles the results show that the network RTK is an approved method for determining height, depending on the requirements of the municipality.