Evaluation Of Diffusion-Coefficient And Ionic Mobility In (Nh4)4fe(Cn)6.1.5 H2o

The diffusion coefficient, D, and the ionic mobility, μ, in the protonic conductor ammonium ferrocyanide hydrate have been determined by the isothermal transient ionic current method. D is also determined from the time dependence of the build up of potential across the samples and theretical expressions describing this build up in terms of double exponential dependence on time are obtained. The values obtained are D=3.875×10−11m2s−1 and μ=1.65×10−9 m2V−1s−1.

Harmonising GAP programs for fresh produce in ASEAN region

Many forces are driving the global demand for assurance that fruit and vegetables are safe to eat and of the right quality, and are produced and handled in a manner that does not cause harm to the environment and the health, safety and welfare of workers. The impact of these driving forces is that retailer requirements for suppliers to comply with Good Agricultural Practice (GAP) is increasing and governments are strengthening legal requirements for food safety, environmental protection, and worker health, safety and welfare. The implementation of GAP programs currently within the ASEAN (Association of South East Asian Nations) region varies, with some countries having government certified systems and others beginning the journey with awareness programs for farmers. Under a project funded by the ASEAN Australia Development Cooperation Program, a standard for ASEAN GAP has been developed to harmonise GAP Programs in the region. The goal is to facilitate trade between ASEAN countries and to global markets, improve viability for farmers, and help sustain a safe food supply and the environment. ASEAN GAP is an umbrella standard that individual member countries will benchmark their national programs against to gain equivalence. The scope of ASEAN GAP covers the production, harvesting and postharvest handling of fresh fruit and vegetables on farm and postharvest handling in locations where produce is packed for sale. ASEAN GAP consists of four modules covering food safety, environmental management, worker health, safety and welfare, and produce quality. Each module can be used alone or in combination with other modules. This enables progressive implementation of ASEAN GAP, module by module based on individual country priorities.

Shaping global teacher identity in a short-term mobility programme

This article explores the shaping of Australian and Malaysian pre-service teachers’ possible selves in a short-term mobility programme. With the theory of possible selves, individuals imagine who they will become based on their past and current selves. The focus of the research was on pre-service teachers’ possible selves as global and culturally responsive teachers. The experiential learning through participation in the programme allowed participants to consider their future possible selves as teachers with a deeper understanding of diverse learners’ needs and how they might strive to address these needs in their own classrooms. The scaffolding of reflections in the programme encouraged the pre-service teachers to take on multiple perspectives, to step outside their comfort zones and in many ways to see the world from different eyes. The research found that through experiential learning in the short-term mobility programme both the Australian and Malaysian pre-service teachers gained in positioning their cultural selves currently and as future teachers, suggesting that there is merit in utilising the theory of possible selves in future research in the area of shaping teacher identity.

Firing characteristics of a simple coaxial triggeredva cuum gap

The firing and delay characteristics of a simple coaxial type of triggered vacuum gap (TVG) are described and compared with the planar type. The designs are new and differ from those reported earlier. By analogy with gaseous breakdown the statistical and formative time lags have been determined.

Mobility and security: the perceived benefits of citizenship for resettled young people from refugee backgrounds

In recent decades, the meaning and value of formal state citizenship has shifted dramatically. In the same period, scholarship on citizenship has drawn attention to the proliferation of alternative forms of sub-, supra- and transnational citizenship, at times obscuring the ongoing importance of formal state citizenship. For refugees, however, formal state citizenship remains a critical and widely shared goal. Drawing on interviews with 51 young people from refugee backgrounds in Melbourne, Australia, this article explores the intersecting themes of mobility and security that were identified by participants as the most important benefits of acquiring formal state citizenship in the country of resettlement. In contrast to the insecurity of forced migration, formal state citizenship provides a privileged mobility that enables refugee-background youth to maintain and create transnational identities and attachments and to be protected while doing so, while also granting a secure status within the nation state and insurance against further displacement in an uncertain future. In offering these forms of mobility and security, formal state citizenship contributes to a sense of ontological security among refugee-background youth, providing an important foundation for building national and transnational futures.

Frequency and temperature-dependent mobility of a charged carrier on a randomly interrupted strand

A randomly interrupted strand model of a one-dimensional conductor is considered. An exact analytical expression is obtained for the temperature-dependent ac mobility for a finite segment drawn at random, taking into account the reflecting barriers at the two open ends. The real part of mobility shows a broad resonance as a function of both frequency and temperature, and vanishes quadratically in the dc limit. The frequency (temperature) maximum shifts to higher values for higher temperatures (frequencies).

An elementary approach to gap theorems

Using elementary comparison geometry, we prove: Let (M, g) be a simply-connected complete Riemannian manifold of dimension >= 3. Suppose that the sectional curvature K satisfies -1-s(r) <= K <= -1, where r denotes distance to a fixed point in M. If lim(r ->infinity) e(2r) s(r) = 0, then (M, g) has to be isometric to H-n.The same proof also yields that if K satisfies -s(r) <= K <= 0 where lim(r ->infinity) r(2) s(r) = 0, then (M, g) is isometric to R-n, a result due to Greene and Wu.Our second result is a local one: Let (M, g) be any Riemannian manifold. For a E R, if K < a on a geodesic ball Bp (R) in M and K = a on partial derivative B-p (R), then K = a on B-p (R).

Recognition and enforcement in cross-border insolvency law: A proposal for judicial gap-filling

This Article analyzes the recognition and enforcement of cross-border insolvency judgments from the United States, United Kingdom, and Australia to determine whether the UNCITRAL Model Law’s goal of modified universalism is currently being practiced, and subjects the Model Law to analysis through the lens of international relations theories to elaborate a way forward. We posit that courts could use the express language of the Model Law text to confer recognition and enforcement of foreign insolvency judgments. The adoption of our proposal will reduce costs, maximize recovery for creditors, and ensure predictability for all parties.

Fabrication and characterization of plasma polymer thin films from monoterpene alcohols for applications in organic electronics and biotechnology

After more than twenty years of basic and applied research, the use of nanotechnology in the design and manufacture of nanoscale materials is rapidly increasing, particularly in commercial applications that span from electronics across renewable energy areas, and biomedical devices. Novel polymers are attracting significant attention for they promise to provide a low−cost high−performance alternative to existing materials. Furthermore, these polymers have the potential to overcome limitations imposed by currently available materials thus enabling the development of new technologies and applications that are currently beyond our reach. This work focuses on the development of a range of new low−cost environmentally−friendly polymer materials for applications in areas of organic (flexible) electronics, optics, and biomaterials. The choice of the monomer reflects the environmentally−conscious focus of this project. Terpinen−4−ol is a major constituent of Australian grown Melaleuca alternifolia (tea tree) oil, attributed with the oil's antimicrobial and anti−inflammatory properties. Plasma polymerisation was chosen as a deposition technique for it requires minimal use of harmful chemicals and produces no hazardous by−products. Polymer thin films were fabricated under varied process conditions to attain materials with distinct physico−chemical, optoelectrical, biological and degradation characteristics. The resultant materials, named polyterpenol, were extensively characterised using a number of well−accepted and novel techniques, and their fundamental properties were defined. Polyterpenol films were demonstrated to be hydrocarbon rich, with variable content of oxygen moieties, primarily in the form of hydroxyl and carboxyl functionalities. The level of preservation of original monomer functionality was shown to be strongly dependent on the deposition energy, with higher applied power increasing the molecular fragmentation and substrate temperature. Polyterpenol water contact angle contact angle increased from 62.7° for the 10 W samples to 76.3° for the films deposited at 100 W. Polymers were determined to resist solubilisation by water, due to the extensive intermolecular and intramolecular hydrogen bonds present, and other solvents commonly employed in electronics and biomedical processing. Independent of deposition power, the surface topography of the polymers was shown to be smooth (Rq <0.5 nm), uniform and defect free. Hardness of polyterpenol coatings increased from 0.33 GPa for 10 W to 0.51 GPa for 100 W (at 500 μN load). Coatings deposited at higher input RF powers showed less mechanical deformation during nanoscratch testing, with no considerable damage, cracking or delamination observed. Independent of the substrate, the quality of film adhesion improved with RF power, suggesting these coatings are likely to be more stable and less susceptible to wear. Independent of fabrication conditions, polyterpenol thin films were optically transparent, with refractive index approximating that of glass. Refractive index increased slightly with deposition power, from 1.54 (10 W) to 1.56 (100 W) at 500 nm. The optical band gap values declined with increasing power, from 2.95 eV to 2.64 eV, placing the material within the range for semiconductors. Introduction of iodine impurity reduced the band gap of polyterpenol, from 2.8 eV to 1.64 eV, by extending the density of states more into the visible region of the electromagnetic spectrum. Doping decreased the transparency and increased the refractive index from 1.54 to 1.70 (at 500 nm). At optical frequencies, the real part of permittivity (k) was determined to be between 2.34 and 2.65, indicating a potential low-k material. These permittivity values were confirmed at microwave frequencies, where permittivity increased with input RF energy – from 2.32 to 2.53 (at 10 GHz ) and from 2.65 to 2.83 (at 20 GHz). At low frequencies, the dielectric constant was determined from current−voltage characteristics of Al−polyterpenol−Al devices. At frequencies below 100 kHz, the dielectric constant varied with RF power, from 3.86 to 4.42 at 1 kHz. For all samples, the resistivity was in order of 10⁸−10⁹ _m (at 6 V), confirming the insulating nature of polyterpenol material. In situ iodine doping was demonstrated to increase the conductivity of polyterpenol, from 5.05 × 10⁻⁸ S/cm to 1.20 × 10⁻⁶ S/cm (at 20 V). Exposed to ambient conditions over extended period of time, polyterpenol thin films were demonstrated to be optically, physically and chemically stable. The bulk of ageing occurred within first 150 h after deposition and was attributed to oxidation and volumetric relaxation. Thermal ageing studies indicated thermal stability increased for the films manufactured at higher RF powers, with degradation onset temperature associated with weight loss shifting from 150 ºC to 205 ºC for 10 W and 100 W polyterpenol, respectively. Annealing the films to 405 °C resulted in full dissociation of the polymer, with minimal residue. Given the outcomes of the fundamental characterisation, a number of potential applications for polyterpenol have been identified. Flexibility, tunable permittivity and loss tangent properties of polyterpenol suggest the material can be used as an insulating layer in plastic electronics. Implementation of polyterpenol as a surface modification of the gate insulator in pentacene-based Field Effect Transistor resulted in significant improvements, shifting the threshold voltage from + 20 V to –3 V, enhancing the effective mobility from 0.012 to 0.021 cm²/Vs, and improving the switching property of the device from 10⁷ to 10⁴. Polyterpenol was demonstrated to have a hole transport electron blocking property, with potential applications in many organic devices, such as organic light emitting diodes. Encapsulation of biomedical devices is also proposed, given that under favourable conditions, the original chemical and biological functionality of terpinen−4−ol molecule can be preserved. Films deposited at low RF power were shown to successfully prevent adhesion and retention of several important human pathogens, including P. aeruginosa, S. aureus, and S. epidermidis, whereas films deposited at higher RF power promoted bacterial cell adhesion and biofilm formation. Preliminary investigations into in vitro biocompatibility of polyterpenol demonstrated the coating to be non−toxic for several types of eukaryotic cells, including Balb/c mice macrophage and human monocyte type (HTP−1 non-adherent) cells. Applied to magnesium substrates, polyterpenol encapsulating layer significantly slowed down in vitro biodegradation of the metal, thus increasing the viability and growth of HTP−1 cells. Recently, applied to varied nanostructured titanium surfaces, polyterpenol thin films successfully reduced attachment, growth, and viability of P. aeruginosa and S. aureus.

Resistance fluctuation at the mobility edge

Following a Migdal-Kadanoff-type bond moving procedure, we derive the renormalisation-group equations for the characteristic function of the full probability distribution of resistance (conductance) of a three-dimensional disordered system. The resulting recursion relations for the first two cumulants, K, the mean resistance and K ~ t,he meansquare deviation of resistance exhibit a mobility edge dominated by large dispersion, i.e., K $ ’/ K=, 1, suggesting inadequacy of the one-parameter scaling ansatz.

Delay time of a vacuum gap triggered by an exploding wire

The experimental results of delay time of a vacuum gap triggered by an exploding wire plasma have been reported. It consists of explosion delay time and propagation delay time. The explosion delay time has been found to be dependent on the parameters of the exploding wire and the exploding wire circuit and is independent of vacuum gap configuration. The propagation delay time depends on the properties of the exploding wire plasma and vacuum gap parameters such as the number of injection slots, gap spacing, gap polarity, etc. In the absence of prebreakdown current in the vacuum gap, the breakdown can be initiated only after the plasma completely bridges the gap spacing. Under this specific condition, it has been shown that the delay time data can be used to calculate the plasma velocity.

Engagement with superannuation: Is there really a gender gap?

A recent report produced by Suncorp Bank and The association of Superannuation Funds of Australia (ASFA) found women were less engaged with their superannuation than men (2012). Given that women have lower superannuation balances than men, a lack of engagement could leader to a further reduction in their ability to provide for themselves in retirement (Basu and Drew, 2009). Using a variety of measures of engagement, we find women are mostly as engaged as men. The main determinants of engagement continue to be financial literacy, age and value of superannuation.

Chinese cultural competency and Australian law students: Reflections on the design of short term mobility programs

There is an emerging need for Australia’s law graduates to better understand the unique challenges and opportunities in our largest trading partner, China. Similarly, as China opens up to the world, its graduates are increasingly well-poised to make an indelible mark on Chinese-Australian relations, particularly in the areas of finance, property, trade and commerce. Chinese and Australian law schools must urgently develop a deeper awareness of each other’s language, culture and political systems in their graduates. The purpose of this article is to highlight the importance of Chinese cultural competency to Australian legal education and reflect on projects that enable students to attain a level of cultural competency over a short period. We do this by considering a recent ‘short term mobility project’ in Wuhan, China.

Self-excited triggered vacuum gap

The self-triggering action of the TVG under DC conditions using the same power source as the main circuit is described. Because of the low impedance of the power source compared with the thyratron pulse generator, the TVG can be triggered with voltages as low as 85 V. It is found that circuit conditions influence the minimum stable arc currents that can be sustained.

Seamless journeys : enhancing accessibility to work through digital technologies for people with mobility-related impairments

Numerous disruptions and barriers are encountered by persons with mobility-related disabilities in their daily’s experience of going to work and the pressure these exert on gaining and maintaining their employment. The nature and extent of their difficulties to workforce participation entails a requirement for extensive planning and also strategies to address problems of being stranded (for example, when the bus they are waiting for is not accessible). This paper presents the conceptualisation and methods of understanding workforce participation as a journey, and a discussion on the role digital technologies play in helping people with mobility-related disabilities in their journeys to work and mitigating disruptions when these occur. This is presented through an initial case study that helped identify the sequence of supports needed to be in place to make the work journey possible. Importantly, the paper also highlights points of intervention for the use of digital technologies and where design can potentially help to enhance accessibility to work for people with mobility-related impairments by making journeys to work seamless.