Determination of acrylamide levels in selected commercial and traditional foods in Syria

Purpose: To determine acrylamide (AA) levels in different brands of commercial and traditional foodstuffs available in Syria by ultra-performance liquid chromatography-mass spectrometery (UPLCMS). Methods: A total of 63 samples were analyzed. Food samples were defatted by hexane and then extracted with methanol 98 % in a vortex mixer. Thereafter, Carrez I and Carrez II were added to precipitate proteins from the co-extractives and then centrifuged to obtain a clear aqueous extract that was evaporated to dryness. The extract was dissolved in 1 mL of water, eluted through a preconditioned Oasis HLB cartridge and then filtered. The filtrate was analyzed by UPLC-MS/MS to determine AA content. Results: Among the commercial foods tested, the highest acrylamide quantity was found in potato products (396 ± 3.59 – 1844 ± 5.29 μg kg−1) and the lowest in corn products (183 ± 2.64 – 366 ± 4.58 μg kg−1). This was followed by biscuits (57 ± 2.64 – 1433 ± 2.51 μg kg−1), breakfast cereals (121 ± 8.73 – 245 ± 3.60 μg kg−1), bread (119 ± 1.73 – 263 ± 3.60 μg kg−1) and then coffee (113 ± 2.64 - 64 ± 3.05 μg kg−1). Regarding traditional foods, the highest level of AA was found in AL- Mshabak (481 ± 2.08 μg kg−1) and AL-Awamat (421 ± 2.64 μg kg−1) followed by AL-Namora (282 ± 4.35 μg kg−1) and AL-Kenafa (242 ± 2.64 μg kg−1). It was also observed that the lowest amount of AA was in fried bread (230 μg kg−1), AL-Fatayer (192 ± 3.51 μg kg−1) and AL-Baqlawa (172 ± 4.35 μg kg−1) while Eid Aqras (130 ± 4.58 μg kg−1) and AL-Brazeq (167 ± 3.78 μg kg−1) contained the least amount of AA. Conclusion: The results indicate that the highest levels of AA are found in the most commonly consumed foods. There was significant difference (p < 0.05) in AA levels among different food items and within different brands of the same product.

A SCR Model based on Reactor and Engine Experimental Studies for a Cu-zeolite Catalyst

A NOx reduction efficiency higher than 95% with NH3 slip less than 30 ppm is desirable for heavy-duty diesel (HDD) engines using selective catalytic reduction (SCR) systems to meet the US EPA 2010 NOx standard and the 2014-2018 fuel consumption regulation. The SCR performance needs to be improved through experimental and modeling studies. In this research, a high fidelity global kinetic 1-dimensional 2-site SCR model with mass transfer, heat transfer and global reaction mechanisms was developed for a Cu-zeolite catalyst. The model simulates the SCR performance for the engine exhaust conditions with NH3 maldistribution and aging effects, and the details are presented. SCR experimental data were collected for the model development, calibration and validation from a reactor at Oak Ridge National Laboratory (ORNL) and an engine experimental setup at Michigan Technological University (MTU) with a Cummins 2010 ISB engine. The model was calibrated separately to the reactor and engine data. The experimental setup, test procedures including a surrogate HD-FTP cycle developed for transient studies and the model calibration process are described. Differences in the model parameters were determined between the calibrations developed from the reactor and the engine data. It was determined that the SCR inlet NH3 maldistribution is one of the reasons causing the differences. The model calibrated to the engine data served as a basis for developing a reduced order SCR estimator model. The effect of the SCR inlet NO2/NOx ratio on the SCR performance was studied through simulations using the surrogate HD-FTP cycle. The cumulative outlet NOx and the overall NOx conversion efficiency of the cycle are highest with a NO2/NOx ratio of 0.5. The outlet NH3 is lowest for the NO2/NOx ratio greater than 0.6. A combined engine experimental and simulation study was performed to quantify the NH3 maldistribution at the SCR inlet and its effects on the SCR performance and kinetics. The uniformity index (UI) of the SCR inlet NH3 and NH3/NOx ratio (ANR) was determined to be below 0.8 for the production system. The UI was improved to 0.9 after installation of a swirl mixer into the SCR inlet cone. A multi-channel model was developed to simulate the maldistribution effects. The results showed that reducing the UI of the inlet ANR from 1.0 to 0.7 caused a 5-10% decrease in NOx reduction efficiency and 10-20 ppm increase in the NH3 slip. The simulations of the steady-state engine data with the multi-channel model showed that the NH3 maldistribution is a factor causing the differences in the calibrations developed from the engine and the reactor data. The Reactor experiments were performed at ORNL using a Spaci-IR technique to study the thermal aging effects. The test results showed that the thermal aging (at 800°C for 16 hours) caused a 30% reduction in the NH3 stored on the catalyst under NH3 saturation conditions and different axial concentration profiles under SCR reaction conditions. The kinetics analysis showed that the thermal aging caused a reduction in total NH3 storage capacity (94.6 compared to 138 gmol/m3), different NH3 adsorption/desorption properties and a decrease in activation energy and the pre-exponential factor for NH3 oxidation, standard and fast SCR reactions. Both reduction in the storage capability and the change in kinetics of the major reactions contributed to the change in the axial storage and concentration profiles observed from the experiments.

Gräs från våtmark som additiv i bränslepellets : Effekter på pelletskvalitet och energiförbrukning

Because of global warming the energy production development has progressed towards more renewable energy sources. Biomass has great potential in this matter and pellet is already a big market that has increased seven times the past decade. A periodically strained woodchip resource market and statements of short supply in the future has got actors exploring opportunities with other commodities. Grasses such as Canary grass has shown great potential in this matter and in this study a wetland grass is tested as an additive, 0,5, 1,0, 1,5, and 1,9%, with spruce woodchips. The test production series was performed at a production unit located at the department of environmental and energy system at Karlstad University, Karlstad. Quality was controlled accordingly to the European standard and parameters such as energy consumption, moisture content, mechanical durability and bulk density was tested. For comparison, a sample with only spruce wood chips was produced, and a sample containing 1% of a commonly used additive, potato starch. The results showed that a decrease in energy consumption with 14% when 2% wetland grass was added, part of the decline may be due to the increased production flow compared with the reference sample. The positive effects on decrease in energy consumption, that 1% potato starch results in, is equal to reults from 1% wetlandgrass. This indicates lubricating properties in wetlandgrass. This is attributed to that herbaceous plants have a high content of extracts such as waxes and that they cause less friction in the press. Tests also showed that pellet with wetland grass did not qualify the European standard in terms of mechanical durability. Extracts can form a weak boundary layer in the pellet and cause this. A possible trend shows a better mechanical durability with more grass in pellets. The presence of different size of particles can be a reason. Moisture content qualifies according to the European standard but is below optimum 8%. This despite to relatively high moisture content in the mixer. Higher moisture content in the press would certainly result in a generally higher quality. Suggestions for future studies are to produce pellets with greater distribution on the wetland grass added, to easier interpret a connection. Also examine the extracts behavior with different moisture content. For a sustainable development accordingly renewable energy it is important to ensure the future commodity market for pellets. Further studies should be performed to help the development of alternative raw materials in conjunction with pellet production.

Quick concrete

QUICK CONCRETE es un emprendimiento el cual se planteó como una empresa prestadora de servicios en el sector de la construcción en la ciudad de Ibagué, Colombia. Con ayuda de empresas ya reconocidas a nivel regional como lo son: la distribuidora de materiales y ferretería La Española, A&C y la ladrillera Ladrillos Roma. Se espera impactar en el mercado con un método diferente y un precio competitivo de servicio. El mayor impulso de la construcción puede estar asociado a una mayor demanda de vivienda por parte de ciudadanos bogotanos que ven en Ibagué una posibilidad rentable para invertir en vivienda, así como también el crecimiento del comercio que requiere la construcción de centros comerciales y el programa de viviendas de interés social del Gobierno que benefició a Ibague. Sin embargo, este es una actividad bastante cíclica y con una alta rotación de trabajadores.