Microcontroller-based interface circuit for inductive sensors

This work proposes a fully-digital interface circuit for the measurement of inductive sensors using a low-cost microcontroller (µC) and without any intermediate active circuit. Apart from the µC and the sensor, the circuit just requires an external resistor and a reference inductance so that two RL circuits with a high-pass filter (HPF) topology are formed. The µC appropriately excites such RL circuits in order to measure the discharging time of the voltage across each inductance (i.e. sensing and reference) and then it uses such discharging times to estimate the sensor inductance. Experimental tests using a commercial µC show a non-linearity error (NLE) lower than 0.5%FSS (Full-Scale Span) when measuring inductances from 1 mH to 10 mH, and from 10 mH to 100 mH.

Quantificação de fluxos de mercúrio gasoso na interface solo/atmosfera utilizando câmara de fluxo dinâmica: aplicação na bacia do Rio Negro

Gaseous mercury sampling conditions were optimized and a dynamic flux chamber was used to measure the air/surface exchange of mercury in some areas of the Negro river basin with different vegetal coverings. At the two forest sites (flooding and non-flooding), low mercury fluxes were observed: maximum of 3 pmol m-2 h-1 - day and minimum of -1 pmol m-2 h-1 - night. At the deforested site, the mercury fluxes were higher and always positive: maximum of 26 pmol m-2 h-1 - day and 17 pmol m-2 h-1 - night. Our results showed that deforestation could be responsible for significantly increasing soil Hg emissions, mainly because of the high soil temperatures reached at deforested sites.

Estimativa do fluxo de amônia na interface ar-mar na Baía de Guanabara: estudo preliminar

In the begining of April 2004, concentrations of NHx (NH3 + NH4+) were measured in surface waters of the Guanabara Bay. Concentrations varied from 2 to 143 mmol L-1. Ammonia exchange at the air-sea interface was quantified using a numerical model. No measurement of NH3 concentration in air (c air) was performed. Thus, calculations of NH3 flux were based on the assumptions of c air = 1 and 5 µg m-3. Fluxes were predominantly from the water to the atmosphere and varied from -20 to almost 3500 µg N m-2 h-1.

Emergency Management and Wildland-Urban Interface Fires in the United States of America

FEMA's mission is to support our citizens and first responders to ensure that as a Nation we work together to build, sustain, and improve our capability to prepare for, protect against, respond to, recover from, and mitigate all hazards.

Brain Computer Interface for Virtual Reality Control

A brain-computer interface (BCI) is a new communication channel between the human brain and a computer. Applications of BCI systems comprise the restoration of movements, communication and environmental control. In this study experiments were made that used the BCI system to control or to navigate in virtual environments (VE) just by thoughts. BCI experiments for navigation in VR were conducted so far with synchronous BCI and asynchronous BCI systems. The synchronous BCI analyzes the EEG patterns in a predefined time window and has 2 to 3 degrees of freedom.

Non-resorbable glass fibre-reinforced composite with porous surface as bone substitute material: Experimental studies in vitro and in vivo focused on bone-implant interface

The development of load-bearing osseous implant with desired mechanical and surface properties in order to promote incorporation with bone and to eliminate risk of bone resorption and implant failure is a very challenging task. Bone formation and resoption processes depend on the mechanical environment. Certain stress/strain conditions are required to promote new bone growth and to prevent bone mass loss. Conventional metallic implants with high stiffness carry most of the load and the surrounding bone becomes virtually unloaded and inactive. Fibre-reinforced composites offer an interesting alternative to metallic implants, because their mechanical properties can be tailored to be equal to those of bone, by the careful selection of matrix polymer, type of fibres, fibre volume fraction, orientation and length. Successful load transfer at bone-implant interface requires proper fixation between the bone and implant. One promising method to promote fixation is to prepare implants with porous surface. Bone ingrowth into porous surface structure stabilises the system and improves clinical success of the implant. The experimental part of this work was focused on polymethyl methacrylate (PMMA) -based composites with dense load-bearing core and porous surface. Three-dimensionally randomly orientated chopped glass fibres were used to reinforce the composite. A method to fabricate those composites was developed by a solvent treatment technique and some characterisations concerning the functionality of the surface structure were made in vitro and in vivo. Scanning electron microscope observations revealed that the pore size and interconnective porous architecture of the surface layer of the fibre-reinforced composite (FRC) could be optimal for bone ingrowth. Microhardness measurements showed that the solvent treatment did not have an effect on the mechanical properties of the load-bearing core. A push-out test, using dental stone as a bone model material, revealed that short glass fibre-reinforced porous surface layer is strong enough to carry load. Unreacted monomers can cause the chemical necrosis of the tissue, but the levels of leachable resisidual monomers were considerably lower than those found in chemically cured fibre-reinforced dentures and in modified acrylic bone cements. Animal experiments proved that surface porous FRC implant can enhance fixation between bone and FRC. New bone ingrowth into the pores was detected and strong interlocking between bone and the implant was achieved.

An Interface Damage Model for the Simulation of Delamination Under Variable-Mode Ratio in Composite Materials

A thermodynamically consistent damage model for the simulation of progressive delamination under variable mode ratio is presented. The model is formulated in the context of the Damage Mechanics. The constitutive equation that results from the definition of the free energy as a function of a damage variable is used to model the initiation and propagation of delamination. A new delamination initiation criterion is developed to assure that the formulation can account for changes in the loading mode in a thermodynamically consistent way. The formulation proposed accounts for crack closure effets avoiding interfacial penetration of two adjacent layers aftercomplete decohesion. The model is implemented in a finite element formulation. The numerical predictions given by the model are compared with experimental results

Efeitos dos parâmetros operacionais na fotodegradação do azo corante direct red 23 na interface dióxido de titânio/água

The decolorization and degradation of direct red 23 azo dye have been investigated in aqueous suspension of titanium dioxide under artificial irradiation. The effects of some operational parameters such as azo dye concentration, catalyst loading, and solution pH were investigated at 30.0 ºC and optimized values were obtained. The first-order kinetic model was used to discuss the results. The UV-Vis spectra changes showed that the azo dye sample, collected after 6 h irradiation, was 98% decolorized while the residual total carbon was 97.9% degraded, indicating simultaneous photodecolorization and degradation.

Fluxos de óxido nitroso na interface ar-mar na Baía de Guanabara

In Surface water concentrations of N2O were measured at 37 stations in Guanabara Bay and fluxes estimated across the air-sea interface. Concentrations averaged 8.2 ± 2.2 nmol L-1 and 90% of the stations showed supersaturation averaging 33%. N2O fluxes were estimated using a two-film model which is given by the product of the concentration difference across the film and the gas transfer coefficient (k w). Two parametrizations of k w were used which provided average fluxes of 0.3 and 3.0 µg N m-2 h-1. Flux measurements using floating chambers (not reported here) seem to agree with the upper limit of these estimates.

Diretrizes para a formação de professores da educação básica em interface com a licenciatura em química: em contexto as possibilidades formativas

We developed and applied an educational instrument (ID) to discuss, in the discipline of Supervised Pre Service Teachers Practice 1, guidelines for teacher education to redefine teacher knowledge with a specific focus on chemistry teachers. The study used methodological fundamentals of Discursive Textual Analysis that involves identifying and isolating a set of materials subjected to analysis, categorizing these statements and producing texts, integrating these descriptions and interpretations, basing its construction on the category system built. Data were collected through participant observation and text readings used by the students in performing the activity. It was noted that the chemistry teachers trained were able to express opinions that indicated the Construction of Meanings Interface that was the category of analysis established a priori.

Improving and User Interface to E-Procurement Software Used in Asset Accounting and Investigating Effects to Efficiency

This diploma thesis has been done to international organization which takes care from the accounting actions of two major companies. In this organization are used three different purchasing tools which are used when new asset master data is wanted to input to SAP R/3- system. The aim of this thesis is to find out how much changing the user interface of one of these three e-procurement programs will affect to overall efficiency in asset accounting. As an addition will be introduced project framework which can be used in future projects and which help to avoid certain steps in the development process. At the moment data needs to be inputted manually with many useless mouse clicks and data needs to be searched from many various resources which slow down the process. Other organization has better tools at the moment than the myOrders system which is under investigation Research was started by exploring the main improvement areas. After this possible defects were traced. Suggested improvements were thought by exploring literature which has been written from usability design and research. Meanwhile also directional calculations from the benefits of the project were done alongside with the analysis of the possible risks and threats. After this NSN IT approved the changes which they thought was acceptable. The next step was to program them into tool and test them before releasing to production environment. The calculations were made also from implemented improvements and compared them to planned ones From whole project was made a framework which can be utilized also to other similar projects. The complete calculation was not possible because of time schedule of the project. Important observation in the project was that efficiency is not improved not only by changing the GUI but also improving processes without any programming. Feedback from end user should be also listened more in development process. End-user is after all the one who knows the best how the program should look like.

O Cuidado Empático: Contribuições para a Ética e Sua Interface com a Educação Moral na Formação em Saúde

RESUMO O presente artigo apresenta alguns pontos essenciais do pensamento do filósofo Michael Slote em sua obra “The ethics of care and empathy”. Situamos a sua produção no contexto em que a ética do cuidado foi desenvolvida e problematizada, evidenciando, sobretudo, a questão de gênero que atravessa essa perspectiva ética. Assim, convocamos autores e autoras que dialogam estreitamente com as questões levantadas por Slote como interlocutores fundamentais para se pensar a empatia como componente fundamental da ética do cuidado. Em sequência, resgatamos o sentido ontológico do cuidado e da responsabilidade, correlacionando-os com a prática do cuidado em saúde. Ao final, apresentamos um caso paradigmático para um debate concreto da ética do cuidado e empatia no âmbito da educação moral, destacando sua importância no processo de formação dos profissionais de saúde no Brasil.

Análise técnico-jurídica do licenciamento ambiental e sua interface com a certificação ambiental

O objetivo do presente trabalho foi promover uma análise comparativa do licenciamento e da certificação ambiental, para daí extrair uma fundamentação técnica e jurídica que possibilite verificar a interface entre eles. Utilizou-se uma abordagem teórico-metodológica da pesquisa social aplicada e jurídica, através de uma vertente jurídico-dogmática, bem como uma pesquisa dos fundamentos técnicos e sociais, para avaliação dos processos de certificação ambiental. Objetivou-se comprovar a existência de uma nítida interface entre licenciamento e certificação ambiental, embora não se possa admitir a suplantação da atividade estatal ou sequer a modificação das estruturas básicas da certificação. Recomenda-se um diálogo maior entre o Poder Público e as organizações privadas na busca de um desenvolvimento econômico que concretamente visa a sustentabilidade.

The National Digital Library of Finland – Public Interface FINNA

Aki Lassilan esitys IFLA-konferenssissa Helsingissä 14.8.2012.

Design and implementation of robot gripper interface

This thesis presents a design for an asynchronous interface to Robotiq adaptive gripper s-model. Designed interface is a communication layer that works on top of modbus layer. The design contains function definitions, finite state machine and exceptions. The design was not fully implemented but enough was so that it can be used. The implementation was done with c++ in linux environment. Additionally to the implementation a simple demo program was made to show the interface is used. Also grippers closing speed and force were measured. There is also a brief introduction into robotics and robot grasping.