Aerosol mass spectrometric analysis of the chemical composition of non- refractory PM1 samples from school environments in Brisbane, Australia

Long term exposure to vehicle emissions has been associated with harmful health effects. Children are amongst the most susceptible group and schools represent an environment where they can experience significant exposure to vehicle emissions. However, there are limited studies on children’s exposure to vehicle emissions in schools. The aim of this study was to quantify the concentration of organic aerosol and in particular, vehicle emissions that children are exposed to during school hours. Therefore an Aerodyne compact time-of-flight aerosol mass spectrometer (TOF-AMS) was deployed at five urban schools in Brisbane, Australia. The TOF-AMS enabled the chemical composition of the non- refractory (NR-PM1) to be analysed with a high temporal resolution to assess the concentration of vehicle emissions and other organic aerosols during school hours. At each school the organic fraction comprised the majority of NR-PM1 with secondary organic aerosols as the main constitute. At two of the schools, a significant source of the organic aerosol (OA) was slightly aged vehicle emissions from nearby highways. More aged and oxidised OA was observed at the other three schools, which also recorded strong biomass burning influences. Primary emissions were found to dominate the OA at only one school which had an O:C ratio of 0.17, due to fuel powered gardening equipment used near the TOF-AMS. The diurnal cycle of OA concentration varied between schools and was found to be at a minimum during school hours. The major organic component that school children were exposed to during school hours was secondary OA. Peak exposure of school children to HOA occurred during school drop off and pick up times. Unless a school is located near major roads, children are exposed predominately to regional secondary OA as opposed to local emissions during schools hours in urban environments.

Spatial variation of particle number concentration in school microscale environments and its impact on exposure assessment

It has not yet been established whether the spatial variation of particle number concentration (PNC) within a microscale environment can have an effect on exposure estimation results. In general, the degree of spatial variation within microscale environments remains unclear, since previous studies have only focused on spatial variation within macroscale environments. The aims of this study were to determine the spatial variation of PNC within microscale school environments, in order to assess the importance of the number of monitoring sites on exposure estimation. Furthermore, this paper aims to identify which parameters have the largest influence on spatial variation, as well as the relationship between those parameters and spatial variation. Air quality measurements were conducted for two consecutive weeks at each of the 25 schools across Brisbane, Australia. PNC was measured at three sites within the grounds of each school, along with the measurement of meteorological and several other air quality parameters. Traffic density was recorded for the busiest road adjacent to the school. Spatial variation at each school was quantified using coefficient of variation (CV). The portion of CV associated with instrument uncertainty was found to be 0.3 and therefore, CV was corrected so that only non-instrument uncertainty was analysed in the data. The median corrected CV (CVc) ranged from 0 to 0.35 across the schools, with 12 schools found to exhibit spatial variation. The study determined the number of required monitoring sites at schools with spatial variability and tested the deviation in exposure estimation arising from using only a single site. Nine schools required two measurement sites and three schools required three sites. Overall, the deviation in exposure estimation from using only one monitoring site was as much as one order of magnitude. The study also tested the association of spatial variation with wind speed/direction and traffic density, using partial correlation coefficients to identify sources of variation and non-parametric function estimation to quantify the level of variability. Traffic density and road to school wind direction were found to have a positive effect on CVc, and therefore, also on spatial variation. Wind speed was found to have a decreasing effect on spatial variation when it exceeded a threshold of 1.5 (m/s), while it had no effect below this threshold. Traffic density had a positive effect on spatial variation and its effect increased until it reached a density of 70 vehicles per five minutes, at which point its effect plateaued and did not increase further as a result of increasing traffic density.

A case for optimising fracture healing through inverse dynamization

The mechanical conditions in the repair tissues are known to influence the outcome of fracture healing. These mechanical conditions are determined by the stiffness of fixation and limb loading. Experimental studies have shown that there is a range of beneficial fixation stiffness for timely healing and that fixation stiffness that is either too flexible or too stiff impairs callus healing. However, much less is known about how mechanical conditions influence the biological processes that make up the sequence of bone repair and if indeed mechanical stimulation is required at all stages of repair. Secondary bone healing occurs through a sequence of events broadly characterised by inflammation, proliferation, consolidation and remodelling. It is our hypothesis that a change in fixation stiffness from very flexible to stiff can shorten the time to healing relative to constant fixation stiffness. Flexible fixation has the benefit of promoting greater callus formation and needs to be applied during the proliferative stage of repair. The greater callus size helps to stabilize the fragments earlier allowing mineralization to occur faster. Together with stable/rigid fixation applied during the latter stage of repair to ensure mineralization of the callus. The predicted benefits of inverse dynamization are shortened healing in comparison to very flexible fixation and healing time comparable or faster than stable fixation with greater callus stiffness.

"They did not believe me" : Adult survivors' perspectives of child sexual abuse by personnel in Christian Institutions

Executive Summary Child sexual abuse (CSA) in Christian Institutions continues to be of serious concern in public, criminal justice and institutional discourse. This study was conducted in conjunction with Project Kidsafe Foundation and sought the perspectives of Australian survivors of CSA by Personnel in Christian Institutions (PICIs). In total, 81 individual survivors responded to an online survey which asked them a range of questions about their current and childhood life circumstance; the nature, extent and location of abuse; grooming strategies utilised by perpetrators; their experiences of disclosure; and outcomes of official reporting to both criminal justice agencies and also official processes Christian institutions. Survey participants were given the option to further participate in a qualitative interview with the principal researcher. These interviews are not considered within this report. In summary, survey data examined here indicate that: • Instances of abuse included a range of offences from touching outside of clothing to serious penetrative offences. • The onset of abuse occurred at a young age: between 6 and 10 years for most female participants, and 11 and 13 years for male participants. • In the majority of cases the abuse ceased because of actions by survivors, not by adults within families or the Christian institution. • Participants waited significant time before disclosing their abuse, with many waiting 20 years or more. • Where survivors disclosed to family members or PICIs, they were often met with disbelief and unhelpful responses aimed at minimising the harm. • Where an official report was made, it was most often made to police. In these cases 53% resulted in an official investigations. • The primary reasons for reporting were to protect others from the perpetrator and make the Christian institution accountable to an external agency. • Where reports to Christian institutions were made, most survivors were dissatisfied with outcomes, and a smaller majority was extremely dissatisfied. This report reflects the long-held understanding that responding to CSA is a complex and difficult task. If effective and meaningful responses are not made, however, trauma to the survivor is most often compounded and recovery delayed. This report demonstrates the need for further independent analysis and oversight of responses made to CSA by both criminal justice, religious and social institutions. Meaningful change will only be accessible, however, if family, community and institutional environments are safe places for survivors to disclose their experiences of abuse and begin to seek ways of healing. There is much to be learnt from survivors that have already made this journey.

A new model to study healing of a complex femur fracture with concurrent soft tissue injury in sheep

High energy bone fractures resulting from impact trauma are often accompanied by subcutaneous soft tissue injuries, even if the skin remains intact. There is evidence that such closed soft tissue injuries affect the healing of bone fractures, and vice versa. Despite this knowledge, most impact trauma studies in animals have focussed on bone fractures or soft tissue trauma in isolation. However, given the simultaneous impact on both tissues a better understanding of the interaction between these two injuries is necessary to optimise clinical treatment. The aim of this study was therefore to develop a new experimental model and characterise, for the first time, the healing of a complex fracture with concurrent closed soft tissue trauma in sheep. A pendulum impact device was designed to deliver a defined and standardised impact to the distal thigh of sheep, causing a reproducible contusion injury to the subcutaneous soft tissues. In a subsequent procedure, a reproducible femoral butterfly fracture (AO C3-type) was created at the sheep’s femur, which was initially stabilised for 5 days by an external fixator construct to allow for soft tissue swelling to recede, and ultimately in a bridging construct using locking plates. The combined injuries were applied to twelve sheep and the healing observed for four or eight weeks (six animals per group) until sacrifice. The pendulum impact led to a moderate to severe circumferential soft tissue injury with significant bruising, haematomas and partial muscle disruptions. Posttraumatic measurements showed elevated intra-compartmental pressure and circulatory tissue breakdown markers, with recovery to normal, pre-injury values within four days. Clinically, no neurovascular deficiencies were observed. Bi-weekly radiological analysis of the healing fractures showed progressive callus healing over time, with the average number of callus bridges increasing from 0.4 at two weeks to 4.2 at eight weeks. Biomechanical testing after sacrifice showed increasing torsional stiffness between four and eight weeks healing time from 10% to 100%, and increasing ultimate torsional strength from 10% to 64% (relative to the contralateral control limb). Our results demonstrate the robust healing of a complex femur fracture in the presence of a severe soft tissue contusion injury in sheep and demonstrate the establishment of a clinically relevant experimental model, for research aimed at improving the treatment of bone fractures accompanied by closed soft tissue injuries.

Learning environments – Laboratories at the cross roads

Laboratories and technical hands on learning have always been a part of Engineering and Science based university courses. They provide the interface where theory meets practice and students may develop professional skills through interacting with real objects in an environment that models appropriate standards and systems. Laboratories in many countries are facing challenges to their sustainable operation and effectiveness. In some countries such as Australia, significantly reduced funding and staff reduction is eroding a once strong base of technical infrastructure. Other countries such as Thailand are seeking to develop their laboratory infrastructure and are in need of staff skill development, management and staff structure in technical areas. In this paper the authors will address the need for technical development with reference to work undertaken in Thailand and Australia. The authors identify the roads which their respective university sectors are on and point out problems and opportunities. It is hoped that the cross roads where we meet will result in better directions for both.

Effects of scaffold architecture on cranial bone healing

Scaffolds for bone tissue engineering should be designed to optimize cell migration, enhance new bone formation and give mechanical support. In the present study, we used polycaprolactone-tricalciumphosphate (PCL/TCP) scaffolds with two different fibre lay down patterns which were coated with hydroxyapatite and gelatine as an approach for optimizing bone regeneration in a critical sized calvarial defect. After 12 weeks bone regeneration was quantified using microCT analysis, biomechanical testing and histological evaluation. Notably, the experimental groups containing coated scaffolds showed lower bone formation and lower biomechanical properties within the defect compared to the uncoated scaffolds. Surprisingly, the different lay down pattern of the fibres resulted in different bone formation and biomechanical properties; namely 0/60/120° scaffolds revealed lower bone formation and biomechanical properties compared to the 0/90° scaffolds in all the experimental groups. The different architecture of the scaffold fibres may have an effect on nutrition supply as well as the attachment of the newly formed matrix to the scaffold. Therefore, future bone regeneration strategies utilising scaffolds should consider scaffold architecture as an important factor during the scaffold optimisation stages in order to move closer to a clinical application.

Featureless visual processing for SLAM in changing outdoor environments

Vision-based SLAM is mostly a solved problem providing clear, sharp images can be obtained. However, in outdoor environments a number of factors such as rough terrain, high speeds and hardware limitations can result in these conditions not being met. High speed transit on rough terrain can lead to image blur and under/over exposure, problems that cannot easily be dealt with using low cost hardware. Furthermore, recently there has been a growth in interest in lifelong autonomy for robots, which brings with it the challenge in outdoor environments of dealing with a moving sun and lack of constant artificial lighting. In this paper, we present a lightweight approach to visual localization and visual odometry that addresses the challenges posed by perceptual change and low cost cameras. The approach combines low resolution imagery with the SLAM algorithm, RatSLAM. We test the system using a cheap consumer camera mounted on a small vehicle in a mixed urban and vegetated environment, at times ranging from dawn to dusk and in conditions ranging from sunny weather to rain. We first show that the system is able to provide reliable mapping and recall over the course of the day and incrementally incorporate new visual scenes from different times into an existing map. We then restrict the system to only learning visual scenes at one time of day, and show that the system is still able to localize and map at other times of day. The results demonstrate the viability of the approach in situations where image quality is poor and environmental or hardware factors preclude the use of visual features.

Numerical techniques for simulating a fractional mathematical model of epidermal wound healing

A number of mathematical models investigating certain aspects of the complicated process of wound healing are reported in the literature in recent years. However, effective numerical methods and supporting error analysis for the fractional equations which describe the process of wound healing are still limited. In this paper, we consider the numerical simulation of a fractional mathematical model of epidermal wound healing (FMM-EWH), which is based on the coupled advection-diffusion equations for cell and chemical concentration in a polar coordinate system. The space fractional derivatives are defined in the Left and Right Riemann-Liouville sense. Fractional orders in the advection and diffusion terms belong to the intervals (0, 1) or (1, 2], respectively. Some numerical techniques will be used. Firstly, the coupled advection-diffusion equations are decoupled to a single space fractional advection-diffusion equation in a polar coordinate system. Secondly, we propose a new implicit difference method for simulating this equation by using the equivalent of Riemann-Liouville and Grünwald-Letnikov fractional derivative definitions. Thirdly, its stability and convergence are discussed, respectively. Finally, some numerical results are given to demonstrate the theoretical analysis.

Is quality more important if you’re quirky? A review of the literature on differential susceptibility to childcare environments

Evidence concerning the impact of child care on child development suggests that higher-quality environments, particularly those that are more responsive, predict more favourable social and behavioural outcomes. However, the extent of this effect is not as great as might be expected. Impacts on child outcomes are, at best, modest. One recent explanation emerging from a new theoretical perspective of development, differential susceptibility theory, is that a minority of children are more reactive to both positive and negative environments, while the majority are relatively unaffected. These 'quirky' children have temperamental traits that are more extreme, and are often described in research studies as having 'difficult temperaments'. This paper reviews the literature on such children and argues for the need for further research to identify components of childcare environments that optimise the potential of these more sensitive, quirky individuals.

The relationship between airborne small ions and particles in urban environments

Ions play an important role in affecting climate and particle formation in the atmosphere. Small ions rapidly attach to particles in the air and, therefore, studies have shown that they are suppressed in polluted environments. Urban environments, in particular, are dominated by motor vehicle emissions and, since motor vehicles are a source of both particles and small ions, the relationship between these two parameters is not well known. In order to gain a better understanding of this relationship, an intensive campaign was undertaken where particles and small ions of both signs were monitored over two week periods at each of three sites A, B and C that were affected to varying degrees by vehicle emissions. Site A was close to a major road and reported the highest particle number and lowest small ion concentrations. Precursors from motor vehicle emissions gave rise to clear particle formation events on five days and, on each day this was accompanied by a suppression of small ions. Observations at Site B, which was located within the urban airshed, though not adjacent to motor traffic, showed particle enhancement but no formation events. Site C was a clean site, away from urban sources. This site reported the lowest particle number and highest small ion concentration. The positive small ion concentration was 10% to 40% higher than the corresponding negative value at all sites. These results confirm previous findings that there is a clear inverse relationship between small ions and particles in urban environments dominated by motor vehicle emissions.

Synthesis and characterisation of titanium sol-gels in varied gravity environments

Sol-gel synthesis in varied gravity is only a relatively new topic in the literature and further investigation is required to explore its full potential as a method to synthesise novel materials. Although trialled for systems such as silica, the specific application of varied gravity synthesis to other sol-gel systems such as titanium has not previously been undertaken. Current literature methods for the synthesis of sol-gel material in reduced gravity could not be applied to titanium sol-gel processing, thus a new strategy had to be developed in this study. To successfully conduct experiments in varied gravity a refined titanium sol-gel chemical precursor had to be developed which allowed the single solution precursor to remain un-reactive at temperatures up to 50oC and only begin to react when exposed to a pressure decrease from a vacuum. Due to the new nature of this precursor, a thorough characterisation of the reaction precursors was subsequently undertaken with the use of techniques such as Nuclear Magnetic Resonance, Infra-red and UV-Vis spectroscopy in order to achieve sufficient understanding of precursor chemistry and kinetic stability. This understanding was then used to propose gelation reaction mechanisms under varied gravity conditions. Two unique reactor systems were designed and built with the specific purpose to allow the effects of varied gravity (high, normal, reduced) during synthesis of titanium sol-gels to be studied. The first system was a centrifuge capable of providing high gravity environments of up to 70 g’s for extended periods, whilst applying a 100 mbar vacuum and a temperature of 40-50oC to the reaction chambers. The second system to be used in the QUT Microgravity Drop Tower Facility was also required to provide the same thermal and vacuum conditions used in the centrifuge, but had to operate autonomously during free fall. Through the use of post synthesis characterisation techniques such as Raman Spectroscopy, X-Ray diffraction (XRD) and N2 adsorption, it was found that increased gravity levels during synthesis, had the greatest effect on the final products. Samples produced in reduced and normal gravity appeared to form amorphous gels containing very small particles with moderate surface areas. Whereas crystalline anatase (TiO2), was found to form in samples synthesised above 5 g with significant increases in crystallinity, particle size and surface area observed when samples were produced at gravity levels up to 70 g. It is proposed that for samples produced in higher gravity, an increased concentration gradient of water is forms at the bottom of the reacting film due to forced convection. The particles formed in higher gravity diffuse downward towards this excess of water, which favours the condensation reaction of remaining sol gel precursors with the particles promoting increased particle growth. Due to the removal of downward convection in reduced gravity, particle growth due to condensation reaction processes are physically hindered hydrolysis reactions favoured instead. Another significant finding from this work was that anatase could be produced at relatively low temperatures of 40-50oC instead of the conventional method of calcination above 450oC solely through sol-gel synthesis at higher gravity levels. It is hoped that the outcomes of this research will lead to an increased understanding of the effects of gravity on chemical synthesis of titanium sol-gel, potentially leading to the development of improved products suitable for diverse applications such as semiconductor or catalyst materials as well as significantly reducing production and energy costs through manufacturing these materials at significantly lower temperatures.

Collaborative learning and critical thinking in technology-enhanced environments : an instructional design framework

The nature and characteristics of how learners learn today are changing. As technology use in learning and teaching continues to grow, its integration to facilitate deep learning and critical thinking becomes a primary consideration. The implications for learner use, implementation strategies, design of integration frameworks and evaluation of their effectiveness in learning environments cannot be overlooked. This study specifically looked at the impact that technology-enhanced learning environments have on different learners’ critical thinking in relation to eductive ability, technological self-efficacy, and approaches to learning and motivation in collaborative groups. These were explored within an instructional design framework called CoLeCTTE (collaborative learning and critical thinking in technology-enhanced environments) which was proposed, revised and used across three cases. The field of investigation was restricted to three key questions: 1) Do learner skill bases (learning approach and eductive ability) influence critical thinking within the proposed CoLeCTTE framework? If so, how?; 2) Do learning technologies influence the facilitation of deep learning and critical thinking within the proposed CoLeCTTE framework? If so, how?; and 3) How might learning be designed to facilitate the acquisition of deep learning and critical thinking within a technology-enabled collaborative environment? The rationale, assumptions and method of research for using a mixed method and naturalistic case study approach are discussed; and three cases are explored and analysed. The study was conducted at the tertiary level (undergraduate and postgraduate) where participants were engaged in critical technical discourse within their own disciplines. Group behaviour was observed and coded, attributes or skill bases were measured, and participants interviewed to acquire deeper insights into their experiences. A progressive case study approach was used, allowing case investigation to be implemented in a "ladder-like" manner. Cases 1 and 2 used the proposed CoLeCTTE framework with more in-depth analysis conducted for Case 2 resulting in a revision of the CoLeCTTE framework. Case 3 used the revised CoLeCTTE framework and in-depth analysis was conducted. The findings led to the final version of the framework. In Cases 1, 2 and 3, content analysis of group work was conducted to determine critical thinking performance. Thus, the researcher used three small groups where learner skill bases of eductive ability, technological self-efficacy, and approaches to learning and motivation were measured. Cases 2 and 3 participants were interviewed and observations provided more in-depth analysis. The main outcome of this study is analysis of the nature of critical thinking within collaborative groups and technology-enhanced environments positioned in a theoretical instructional design framework called CoLeCTTE. The findings of the study revealed the importance of the Achieving Motive dimension of a student’s learning approach and how direct intervention and strategies can positively influence critical thinking performance. The findings also identified factors that can adversely affect critical thinking performance and include poor learning skills, frustration, stress and poor self-confidence, prioritisations over learning; and inadequate appropriation of group role and tasks. These findings are set out as instructional design guidelines for the judicious integration of learning technologies into learning and teaching practice for higher education that will support deep learning and critical thinking in collaborative groups. These guidelines are presented in two key areas: technology and tools; and activity design, monitoring, control and feedback.

Using natural user interfaces for collaborative process modelling in virtual environments

Modelling business processes for analysis or redesign usually requires the collaboration of many stakeholders. These stakeholders may be spread across locations or even companies, making co-located collaboration costly and difficult to organize. Modern process modelling technologies support remote collaboration but lack support for visual cues used in co-located collaboration. Previously we presented a prototype 3D virtual world process modelling tool that supports a number of visual cues to facilitate remote collaborative process model creation and validation. However, the added complexity of having to navigate a virtual environment and using an avatar for communication made the tool difficult to use for novice users. We now present an evolved version of the technology that addresses these issues by providing natural user interfaces for non-verbal communication, navigation and model manipulation.