Determinação de metais em água produzida de petróleo

In order to enable the reuse of the large surplus volume of petroleum produced water for irrigation of crops inedible, the quality evaluation of this water is very important. This work aimed to evaluate the effectiveness of the diffusive gradient in thin films technique (DGT) for the determination of labile Cu (II), Mn (II) and Zn (II) in petroleum produced water destined to reuse in agriculture. Samples were collected at the exit of the wastewater treatment plant (WWTP) (after separation oil/water and flotation) of a Petrobrás onshore production region. Basically, the laboratory experiments with DGT devices involved the evaluation of the behavior of the main variables of the technique for determination of analytes in the samples (diffusion coefficients, immersion time, fractionation of organic and inorganic species, and performance of diffusion gels with different porosities, among others). Also, experiments were conducted based on the solid phase extraction (SPE) protocol with Chelex- 100 resin using previously established protocols to support the study. During the project the possibility of in situ immersions in water treatment plants was evaluated. The DGT technique presented satisfactory results for determination of Mn in produced water, and can be used for in situ determinations. However, the results obtained for Cu and Zn show the need of additional studies

Ocorrência de alteradores endócrinos e fármacos nas águas de abastecimento público e ETE, em duas cidades da área de abrangência da UGRHI-21 e 22

Pós-graduação em Química - IQ

An assessment of the concentrations of pharmaceutical compounds in wastewater treatment plants on the island of Gran Canaria(Spain)

[EN] An assessment of the concentrations of thirteen different therapeutic pharmaceutical compounds was conducted on water samples obtained from different wastewater treatment plants (WWTPs) using solid phase extraction and high- and ultra-high-performance liquid chromatography with mass spectrometry detection (HPLC-MS/MS and UHPLC-MS/MS), was carried out. The target compounds included ketoprofen and naproxen (anti-inflammatories), bezafibrate (lipid-regulating), carbamazepine (anticonvulsant), metamizole (analgesic), atenolol (?-blocker), paraxanthine (stimulant), fluoxetine (antidepressant), and levofloxacin, norfloxacin, ciprofloxacin, enrofloxacin and sarafloxacin (fluoroquinolone antibiotics). The relative standard deviations obtained in method were below 11%, while the detection and quantification limits were in the range of 0.3 ? 97.4 ng·L-1 and 1.1 ? 324.7 ng·L-1, respectively. The water samples were collected from two different WWTPs located on the island of Gran Canaria in Spain over a period of one year. The first WWTP (denoted as WWTP1) used conventional activated sludge for the treatment of wastewater, while the other plant (WWTP2) employed a membrane bioreactor system for wastewater treatment. Most of the pharmaceutical compounds detected in this study during the sampling periods were found to have concentrations ranging between 0.02 and 34.81 ?g·L-1.

Analisi degli aspetti di qualità nella gestione dei sistemi di drenaggio urbano attraverso modellazione numerica e indagini di campo

In order to protect river water quality, highly affected in urban areas by continuos as intermittent immissions, it is necessary to adopt measures to intercept and treat these polluted flows. In particular during rain events, river water quality is affected by CSOs activation. Built in order to protect the sewer system and the WWTP by increased flows due to heavy rains, CSOs divert excess flows to the receiving water body. On the basis of several scientific papers, and of direct evidences as well, that demonstrate the detrimental effect of CSOs discharges, also the legislative framework moved towards a stream standard point of view. The WFD (EU/69/2000) sets new goals for receiving water quality, and groundwater as well, through an integrated immission/emissions phylosophy, in which emission limits are associated with effluent standards, based on the receiving water characteristics and their specific use. For surface waters the objective is that of a “good” ecological and chemical quality status. A surface water is defined as of good ecological quality if there is only slight departure from the biological community that would be expected in conditions of minimal anthropogenic impact. Each Member State authority is responsible for preparing and implementing a River Basin Management Plan to achieve the good ecological quality, and comply with WFD requirements. In order to cope with WFD targets, and thus to improve urban receiving water quality, a CSOs control strategy need to be implemented. Temporarily storing the overflow (or at least part of it) into tanks and treating it in the WWTP, after the end of the storm, showed good results in reducing total pollutant mass spilled into the receiving river. Italian State Authority, in order to comply with WFD statements, sets general framework, and each Region has to adopt a Water Remediation Plan (PTA, Piano Tutela Acque), setting goals, methods, and terms, to improve river water quality. Emilia Romagna PTA sets 25% reduction up to 2008, and 50% reduction up to 2015 fo total pollutants masses delivered by CSOs spills. In order to plan remediation actions, a deep insight into spills dynamics is thus of great importance. The present thesis tries to understand spills dynamics through a numerical and an experimental approach. A four months monitoring and sampling campaign was set on the Bologna sewer network, and on the Navile Channel, that is the WWTP receiving water , and that receives flows from up to 28 CSOs during rain events. On the other hand, the full model of the sewer network, was build with the commercial software InfoWorks CS. The model was either calibrated with the data from the monitoring and sampling campaign. Through further model simulations interdependencies among masses spilled, rain characteristics and basin characteristics are looked for. The thesis can be seen as a basis for further insighs and for planning remediation actions.

Impact of anthropogenic stressors on the population genetics of the common bioindicator Dreissena polymorpha (Pallas, 1771)

Toxicant inputs from agriculture, industry and human settlements have been shown to severely affect freshwater ecosystems. Pollution can lead to changes in population genetic patterns through various genetic and stochastic processes. In my thesis, I investigated the impact of anthropogenic stressors on the population genetics of the zebra mussel Dreissena polymorpha. In order to analyze the genetics of zebra mussel populations, I isolated five new highly polymorphic microsatellite loci. Out of those and other already existing microsatellite markers for this species, I established a robust marker set of six microsatellite loci for D. polymorpha. rnMonitoring the biogeographical background is an important requirement when integrating population genetic measures into ecotoxicological studies. I analyzed the biogeographical background of eleven populations in a section of the River Danube (in Hungary and Croatia) and some of its tributaries, and another population in the River Rhine as genetic outgroup. Moreover, I measured abiotic water parameters at the sampling sites and analyzed if they were correlated with the genetic parameters of the populations. The genetic differentiation was basically consistent with the overall biogeographical history of the populations in the study region. However, the genetic diversity of the populations was not influenced by the geographical distance between the populations, but by the environmental factors oxygen and temperature and also by other unidentified factors. I found strong evidence that genetic adaptation of zebra mussel populations to local habitat conditions had influenced the genetic constitution of the populations. Moreover, by establishing the biogeographical baseline of molecular variance in the study area, I laid the foundation for interpreting population genetic results in ecotoxicological experiments in this region.rnIn a cooperation project with the Department of Zoology of the University of Zagreb, I elaborated an integrated approach in biomonitoring with D. polymorpha by combining the analysis techniques of microsatellite analysis, Comet assay and micronucleus test (MNT). This approach was applied in a case study on freshwater contamination by an effluent of a wastewater treatment plant (WWTP) in the River Drava (Croatia) and a complementary laboratory experiment. I assessed and compared the genetic status of two zebra mussel populations from a contaminated and a reference site. Microsatellite analysis suggested that the contaminated population had undergone a genetic bottleneck, caused by random genetic drift and selection, whereas a bottleneck was not detected in the reference population. The Comet assay did not indicate any difference in DNA damage between the two populations, but MNT revealed that the contaminated population had an increased percentage of micronuclei in hemocytes in comparison to the reference population. The laboratory experiment with mussels exposed to municipal wastewater revealed that mussels from the contaminated site had a lower percentage of tail DNA and a higher percentage of micronuclei than the reference population. These differences between populations were probably caused by an overall decreased fitness of mussels from the contaminated site due to genetic drift and by an enhanced DNA repair mechanism due to adaptation to pollution in the source habitat. Overall, the combination of the three biomarkers provided sufficient information on the impact of both treated and non-treated municipal wastewater on the genetics of zebra mussels at different levels of biological organization.rnIn my thesis, I could show that the newly established marker set of six microsatellite loci provided reliable and informative data for population genetic analyses of D. polymorpha. The adaptation of the analyzed zebra mussel populations to the local conditions of their habitat had a strong influence on their genetic constitution. We found evidence that the different genetic constitutions of two populations had influenced the outcome of our ecotoxicological experiment. Overall, the integrated approach in biomonitoring gave comprehensive information about the impact of both treated and non-treated municipal wastewater on the genetics of zebra mussels at different levels of biological organization and was well practicable in a first case study.

REMEDIATION OF TETRACYCLINE FROM WATER SOURCES USING VETIVER GRASS (Chrysopogon zizanioides L. Nash) AND TETRACYCLINE-TOLERANT ROOT-ASSOCIATED BACTERIA

Antibiotics are emerging contaminants worldwide. Due to insufficient policy regulations, public awareness, and the constant exposure of the environment to antibiotic sources has created a major environmental concern. Wastewater treatment plants (WWTP) are not equipped to filter-out these compounds before the discharge of the disinfected effluent into water sources (e.g., lakes and streams) and current available technologies are not equipped to remediate these compounds from environmental sources. Hence, the challenge remains to establish a biological system to remove these antibiotics from wastewater. An invitro hydroponic remediation system was developed using vetiver grass (Chrysopogon zizanioides L. Nash) to remediate tetracycline (TC) from water. Comparative metabolomics studies were conducted to investigate the metabolites/pathways associated with tetracycline metabolism in plants and TC-degrading bacteria. The results show that vetiver plants effectively uptake tetracycline from water sources. Vetiver root-associated bacteria recovered during the hydroponic remediation trial were highly tolerant to TC (as high as 600 ppm) and could use TC as a sole carbon and energy source. Growth conditions (pH, temperature, and oxygen requirement) for TC-tolerant bacteria were optimized for higher TC remediation capability from water sources. The plant (roots and shoots) and bacterial species were further characterized for the metabolites produced during the TC degradation process using GC-MS to identify the possible biochemical mechanism involved. Also, the plant root zone was screened for metabolites/enzymes that were secreted during antibiotic degradation and could potentially enhance the degradation process. The root zone was selected for this analysis because this region of the plant has shown a greater capacity for antibiotic degradation compared to the shoot zone. The role of antioxidant enzymes in TC degradation process revealed glutathione-S-transferase (GSTs) as an important group of enzymes in both plant and bacteria potentially involved in TC degradation process. Metabolomics results also suggest potential GST activity in the TC remediation/ transformation process used by plants. This information could be useful in gaining insights for the application of biological remediation systems for the mitigation of antibiotics from waste-water.

Residuos orgánicos como fuentes de fósforo

En este trabajo, se han llevado a cabo distintos experimentos en laboratorio, con el objetivo de estudiar el efecto de la aplicación de residuos orgánicos como fuentes de P en las pérdidas de este elemento, que se producen en suelo, tanto por escorrentía superficial como por lixiviación. El interés por evaluar las pérdidas de P se debe a la necesidad de conocer mejor los factores que influyen en los procesos de pérdidas de este elemento y así, poder reducir los problemas de eutrofización de aguas, tanto superficiales como subterráneas, provocadas por un exceso de este nutriente, junto con otros como el nitrógeno. Los trabajos experimentales que se han llevado a cabo se detallan a continuación: Se ha realizado el estudio de las formas de P contenidas en una serie de 14 residuos orgánicos, de distinto origen y tratamiento (compost, lodos, purines y digestato), comparando la información aportada por tres protocolos de fraccionamientos de P diferentes, seleccionados entre los principales métodos utilizados: protocolo de fraccionamiento de Ruttemberg (1992), protocolo de Normas, medidas y ensayos (Ruban et al., 2001a) y protocolo de Huang et al. (2008). Todos los métodos de fraccionamiento empleados aportaron información útil para conocer las formas de P de los residuos, a pesar de que alguno de ellos fue descrito para sedimentos o suelos. Sin embargo, resulta difícil comparar los resultados entre unos y otros, ya que cada uno emplea extractantes y tiempos de ensayos diferentes. Las cantidades de P total determinadas por cada método mantienen una relación lineal, aunque el método SMT, por ser más directo, obtiene las cantidades más elevadas para todos los residuos. Los métodos secuenciales (métodos de Huang y Ruttemberg), a pesar de ser más largos y tediosos, aportan información más detallada de la disponibilidad de las formas de P, y con ello, permiten obtener una mejor estimación de las pérdidas potenciales de este elemento tras su aplicación en suelo. Se han encontrado relaciones positivas entre las fracciones determinadas por estos dos métodos. Así mismo, se encuentra una correlación entre las formas solubles de P y la concentración de los iones [Ca + Fe + Al] de los residuos, útiles como indicadores de la disponibilidad de este elemento. Sin embargo, el protocolo SMT, no obtiene información de la solubilidad o disponibilidad de las formas de P contenidas, ni las formas determinadas mantienen relaciones directas con las de los otros métodos, con excepción del P total. Para el estudio del comportamiento de los residuos aplicados en suelos, se pusieron a punto sistemas de lluvia simulada, con el objetivo de caracterizar las pérdidas de P en la escorrentía superficial generada. Por otra parte, se emplearon columnas de suelos enmendados con residuos orgánicos, para el estudio de las pérdidas de P por lixiviación. Los ensayos de simulación de lluvia se llevaron a cabo de acuerdo al “National Phosphorus Research proyect“ (2001), que consigue simular eventos sucesivos de lluvia en unas condiciones semejantes a la realidad, empleando cajas llenas de suelo del horizonte superficial, con residuos aplicados tanto superficialmente como mediante mezcla con el propio suelo. Los ensayos se realizaron con seis residuos de diferente naturaleza y sometidos a distintos tratamientos. Se encontraron diferencias significativas en las pérdidas de las formas de P analizadas, tanto disueltas como particuladas, en las aguas de escorrentía generadas. En general, las pérdidas en el primer evento de lluvia tras la aplicación de los residuos fueron mayores a las generadas en el segundo evento, predominando las formas de P particuladas respecto a las disueltas en ambos. Se encontró una relación positiva entre las pérdidas de P en las aguas de escorrentía generadas en cada ensayo, con los contenidos de P soluble en agua y fácilmente disponible de los residuos empleados, determinados por los protocolos de fraccionamientos secuenciales. Además, se emplearon los modelos matemáticos desarrollados por Vadas et al. (2005, 2007), de evaluación de las pérdidas de P por escorrentía para fertilizantes y estiércoles. La predicción de estos modelos no se cumple en el caso de todos los residuos. Las distintas propiedades físicas de los residuos pueden afectar a las diferencias entre las pérdidas experimentales y las esperadas. Los ensayos de simulación del proceso de lixiviación se llevaron a cabo en columnas de percolación, con suelos enmendados con residuos orgánicos, de acuerdo a la norma “CEN/TS 14405–2004: Caracterización de los residuos – Test de comportamiento de lixiviación – Test de flujo ascendente”. Las pérdidas de P por procesos de lixiviación de agua, han sido despreciadas durante mucho tiempo respecto a las pérdidas por escorrentía. Sin embargo, se ha demostrado que deben tenerse en consideración, principalmente en algunos tipos de suelos o zonas cercanas a acuíferos. Se utilizaron tres suelos de distinta procedencia para los ensayos, de manera que se pudo estudiar la influencia del tipo de suelo en las pérdidas de P para cada tipo de residuo (purín, compost, digestato y lodo de EDAR). Los índices de adsorción de P determinados para cada suelo permiten evaluar aquellos que presentarán más riesgo de producir pérdidas de este elemento al aplicarse fuentes externas de P, encontrando una relación positiva entre ambos. Las pérdidas de P en los lixiviados varían en función tanto del residuo como del suelo empleado. Para el compost, el purín y el lodo, se encontró una relación entre las pérdidas generadas en el agua lixiviada de las columnas y las formas de P soluble contenidas en los residuos. Sin embargo, en el caso del digestato, no existía esta correlación. Las pérdidas para este residuo fueron en todos los casos menores a las estimadas, considerando las formas de P contenido. El estudio de la mojabilidad, propiedad física del residuo que evalúa la capacidad de interacción residuo-agua, permitió explicar el comportamiento anómalo de este residuo, con una mayor resistencia a que el agua entrara en su estructura y por tanto, una mayor dificultad de solubilizar el P contenido en el propio residuo, que en el caso de otros residuos. En general, podemos considerar que el estudio de las formas de P más disponibles o solubles en agua, aporta información útil de las pérdidas potenciales de P. Sin embargo, es necesario estudiar las propiedades físicas de los residuos orgánicos aplicados y la capacidad de adsorción de P de los suelos, para estimar las pérdidas de P y con ello, colaborar a controlar los procesos de eutrofización en aguas. ABSTRACT This dissertation explores the effect of organic wastes application as sources of P in losses of this element that occur by both surface runoff and leaching in soil. To do so, diverse laboratory experiments are conducted and presented here. Evaluating P losses is necessary to better understand the factors that influence the processes behind the loss of this element. Reducing P losses reduces eutrophication problems of both surface water and groundwater caused by an excess of this nutrient, along with other as nitrogen. Details of the experiments are presented below: The first experiment studies the forms of P contained in a series of 14 organic wastes of different origin and treatment (compost, sludge, slurry and digestate), comparing the information provided by three methods of P fractionation. The methods selected were: Ruttemberg protocol (1992); Standards, Measurements and Testing protocol (Ruban et al., 2001a); and Huang protocol (Huang et al., 2008). All fractionation methods employed successfully contribute to our knowledge of P forms in wastes, even though one of them was originally described for sediments or soils information. However, it is difficult to compare results among each other, as each protocol employs different extractants and time in the trials. Total amounts of P obtained by each method show a linear relationship, although the SMT method, which is more direct, obtains the highest amounts for all residues. Sequential methods (Huang and Ruttemberg’s protocols), despite being longer and more tedious, provide more detailed information on the availability of the forms of P. Therefore, allow the estimation of the potential losses of P after application in soil. Furthermore, positive relationships have been found among fractions obtained by these methods. Positive relationship has been found also among soluble forms of P and the concentration of ions Fe + Ca + Al, which is useful as an indicator of the availability of this element. However, the SMT protocol does not collect information about solubility or availability of forms of P contained; neither do certain forms maintain direct relations with the forms from other methods, with the exception of total P methods. To study the behavior of wastes applied to soils two experiments were conducted. Simulated rain systems were prepared to characterize P losses in the surface runoff generated. In addition, columns of soils amended with organic waste were developed for the study of P leaching losses. Simulated rain systems were carried out according to the ’National Phosphorus Research Project’ (2001), which manages to simulate successive rainfall events in conditions resembling reality. The experiment uses boxes filled with soil from the surface horizon amended with residues, both superficially and by mixing with the soil. Tests were conducted with six residues of different type and subjected to diverse treatments. Findings show significant differences in losses of the P forms analyzed in the generated runoff water, in both solution and particulate forms. In general, losses in the first rainfall event after application of waste were higher than the losses generated in the second event, predominating particulate forms of P over dissolved forms in both events. In all trials, a positive relationship was found between various P forms determined by sequential fractionation protocols (water soluble P and readily available P forms) and P losses in runoff. Furthermore, results from Vadas´s mathematical models (Vadas et al., 2005; 2007) to assess P losses by runoff fertilizers and manures indicate that the prediction of this model is not fulfilled in the case of all residues. The diverse physical properties of wastes may affect the differences between experimental and expected losses. Finally, leaching simulation processes were carried out in percolation columns, filled with soils amended with organic wastes, following the ‘CEN/TS 14405-2004 standard: Characterization of waste - Leaching behavior test - Test Flow ascending ’. P losses by leaching have been neglected for a long time with respect to runoff losses. However, findings corroborate previous studies showing that these P losses have to be taken into account, especially in certain types of soils and in zones near aquifers. To study the influence of soil type on P losses, experiments were carried out with three different soils and for each type of waste (manure, compost, digestate and sludge WWTP). Each soil’s P adsorption rates allow assessing which soils imply a higher risk of P losses when external sources of P are applied. P losses in leachate vary according to the type of soil employed and according to the specific residue. In the case of compost, manure and sludge, there is a relationship between leaching losses and residues’ soluble forms of P. The exception being the digestate, where there was no such correlation. Digestate P losses by leaching were lower than expected in all cases considering the forms of P contained. Moreover, examining digestate wettability -- that is, the physical property of the residue that assesses the capacity of waste-water interaction -- allowed explaining the anomalous behavior of this residue. Digestate has a high resistance to water entering its structure and thus higher difficulty to solubilize the P contained. Overall, studying the more available or soluble P forms provides useful information about the potential loss of P. However, this dissertation shows that it is necessary to examine the physical properties of organic residues applied as well as the P adsorption capacity of soils to estimate P losses, and thus to control eutrophication in water.

Implementación del modelo de digestión anaerobia ADM1 en MATLAB/SIMULINK

Este trabajo tiene por objeto la implementación del modelo ADM1 (The IWA Anaerobic Digestion Model No.1), para evaluar su capacidad de simular el proceso de digestión anaerobia de lodos de agua residual. Para implementar el modelo ADM1 se eligió el software Matlab y su herramienta Simulink, por su capacidad para simular sistemas dinámicos. Los resultados demostraron que la simulación a través de la implementación del modelo ADM1, es capaz de predecir la mayoría de los valores medios correspondientes a los parámetros de control más comunes del proceso de digestión anaerobia que se lleva a cabo en la Estación de depuración de aguas residuales (EDAR) sur de Madrid. Se deduce del estudio que la implementación del modelo ADM1 desarrollada mediante Matlab/Simulink, es capaz de simular el proceso dinámico de digestión anaerobia de cualquier EDAR, si se ajustan algunos de los parámetros del modelo para cada caso concreto. Abstract This work aims at the implementation of The IWA Anaerobic Digestion Model No.1 (ADM1) in order to assess its ability to simulate the anaerobic digestion process of wastewater sludge. A Matlab/Simulink implementation of the ADM1 was developed, the simulations results shows that the ADM1 is able to predict the average values of the most common control parameters of the anaerobic digestion process that takes place in the Waste water treatment plant (WWTP) south of Madrid. It is deduced of the estudy that the Matlab implementation of the ADM1 developed, is able to simulate the anaerobic digestion dynamic process of a WWTP, if some of the model parameters are fitted for each specific case.

La reutilización de efluentes depurados en España: retrospectiva, desarrollo del marco normativo, estudio de las tecnologías de regeneración frente a los biorreactores de membrana y sus costes en función del uso

La reutilización de efluentes depurados siempre ha sido una opción en lugares con déficit coyuntural o estructural de recursos hídricos, se haya o no procedido a la regulación y planificación de esta práctica. La necesidad se crea a partir de las demandas de una zona, normalmente riego agrícola, que ven un mejor desarrollo de su actividad por contar con este recurso. España es el país de la UE que más caudal reutiliza, y está dentro de los diez primeros a nivel mundial. La regulación de esta práctica por el RD 1620/2007, ayudó a incorporar la reutilización de efluentes depurados a la planificación hidrológica como parte de los programas de medidas, con objeto de mitigar presiones, como son las extracciones de agua superficial y subterránea, o mejoras medioambientales evitando un vertido. El objeto de este trabajo es conocer la situación de la reutilización de efluentes depurados en España, los diferentes escenarios y planteamientos de esta actividad, el desarrollo del marco normativo y su aplicabilidad, junto a los tratamientos que permiten alcanzar los límites de calidad establecidos en la normativa vigente, en función de los distintos usos. Además, se aporta un análisis de costes de las distintas unidades de tratamiento y tipologías de líneas de regeneración, tanto de las utilizadas después de un tratamiento secundario como de otras opciones de depuración, como son los biorreactores de membrana (MBRs). Para el desarrollo de estos objetivos, en primer lugar, se aborda el conocimiento de la situación de la reutilización en España a través de una base de datos diseñada para cubrir todos los aspectos de esta actividad: datos de la estación depuradora de aguas residuales (EDAR), de la estación regeneradora (ERA), caudales depurados, reutilizados, volúmenes utilizados y ubicación de los distintos usos, tipos de líneas de tratamiento, calidades del agua reutilizada, etc. Las principales fuentes de información son las Confederaciones Hidrográficas (CCHH) a través de las concesiones de uso del agua depurada, las entidades de saneamiento y depuración de las distintas comunidades autónomas (CCAA), ayuntamientos, Planes Hidrológicos de Cuenca (PHC) y visitas a las zonas más emblemáticas. Además, se revisan planes y programas con el fin de realizar una retrospectiva de cómo se ha ido consolidando y desarrollando esta práctica en las distintas zonas de la geografía española. Se han inventariado 322 sistemas de reutilización y 216 tratamientos de regeneración siendo el más extendido la filtración mediante filtro arena seguido de una desinfección mediante hipoclorito, aunque este tratamiento se ha ido sustituyendo por un físico-químico con decantación lamelar, filtro de arena y radiación ultravioleta, tratamiento de regeneración convencional (TRC), y otros tratamientos que pueden incluir membranas, tratamientos de regeneración avanzados (TRA), con dosificación de hipoclorito como desinfección residual, para adaptarse al actual marco normativo. El uso más extendido es el agrícola con el 70% del caudal total reutilizado, estimado en 408 hm3, aunque la capacidad de los tratamientos de regeneración esperada para 2015, tras el Plan Nacional de Reutilización de Aguas (PNRA), es tres veces superior. Respecto al desarrollo normativo, en las zonas donde la reutilización ha sido pionera, las administraciones competentes han ido desarrollando diferentes recomendaciones de calidad y manejo de este tipo de agua. El uso agrícola, y en zonas turísticas, el riego de campos de golf, fueron los dos primeros usos que tuvieron algún tipo de recomendación incluso reglamentación. Esta situación inicial, sin una normativa a nivel estatal ni recomendaciones europeas, creó cierta incertidumbre en el avance de la reutilización tanto a nivel de concesiones como de planificación. En la actualidad sigue sin existir una normativa internacional para la reutilización y regeneración de efluentes depurados. Las recomendaciones de referencia a nivel mundial, y en concreto para el uso agrícola, son las de la OMS (Organización Mundial de la Salud) publicadas 1989, con sus posteriores revisiones y ampliaciones (OMS, 2006). Esta norma combina tratamientos básicos de depuración y unas buenas prácticas basadas en diferentes niveles de protección para evitar problemas sanitarios. Otra normativa que ha sido referencia en el desarrollo del marco normativo en países donde se realiza esta práctica, son las recomendaciones dadas por la Agencia Medioambiente Estadunidense (USEPA, 2012) o las publicadas por el Estado de California (Título 22, 2001). Estas normas establecen unos indicadores y valores máximos dónde el tratamiento de regeneración es el responsable de la calidad final en función del uso. Durante 2015, la ISO trabajaba en un documento para el uso urbano donde se muestra tanto los posibles parámetros que habría que controlar como la manera de actuar para evitar posibles riesgos. Por otro lado, la Comisión Europea (CE) viene impulsando desde el 2014 la reutilización de aguas depuradas dentro del marco de la Estrategia Común de Implantación de la Directiva Marco del Agua, y fundamentalmente a través del grupo de trabajo de “Programas de medidas”. Para el desarrollo de esta iniciativa se está planteando sacar para 2016 una guía de recomendaciones que podría venir a completar el marco normativo de los distintos Estados Miembros (EM). El Real Decreto 1620/2007, donde se establece el marco jurídico de la reutilización de efluentes depurados, tiende más a la filosofía implantada por la USEPA, aunque la UE parece más partidaria de una gestión del riesgo, donde se establecen unos niveles de tolerancia y unos puntos de control en función de las condiciones socioeconómicas de los distintos Estados, sin entrar a concretar indicadores, valores máximos o tratamientos. Sin embargo, en la normativa estadounidense se indican una serie de tratamientos de regeneración, mientras que, en la española, se hacen recomendaciones a este respecto en una Guía sin validez legal. Por tanto, queda sin regular los procesos para alcanzar estos estándares de calidad, pudiendo ser éstos no apropiados para esta práctica. Es el caso de la desinfección donde el uso de hipoclorito puede generar subproductos indeseables. En la Guía de recomendaciones para la aplicación del RD, publicada por el Ministerio de Agricultura y Medioambiente (MAGRAMA) en 2010, se aclaran cuestiones frecuentes sobre la aplicación del RD, prescripciones técnicas básicas para los sistemas de reutilización, y buenas prácticas en función del uso. Aun así, el RD sigue teniendo deficiencias en su aplicación siendo necesaria una revisión de la misma, como en las frecuencias de muestreo incluso la omisión de algunos parámetros como huevos de nematodos que se ha demostrado ser inexistentes tras un tratamiento de regeneración convencional. En este sentido, existe una tendencia a nivel mundial a reutilizar las aguas con fines de abastecimiento, incluir indicadores de presencia de virus o protozoos, o incluir ciertas tecnologías como las membranas u oxidaciones avanzadas para afrontar temas como los contaminantes emergentes. Otro de los objetivos de este trabajo es el estudio de tipologías de tratamiento en función de los usos establecidos en el RD 1620/2007 y sus costes asociados, siendo base de lo establecido a este respecto en la Guía y PNRA anteriormente indicados. Las tipologías de tratamiento propuestas se dividen en líneas con capacidad de desalar y las que no cuentan con una unidad de desalación de aguas salobres de ósmosis inversa o electrodiálisis reversible. Se realiza esta división al tener actuaciones en zonas costeras donde el agua de mar entra en los colectores, adquiriendo el agua residual un contenido en sales que es limitante en algunos usos. Para desarrollar este objetivo se han estudiado las unidades de tratamiento más implantadas en ERAs españolas en cuanto a fiabilidad para conseguir determinada calidad y coste, tanto de implantación como de explotación. El TRC, tiene un coste de implantación de 28 a 48 €.m-3.d y de explotación de 0,06 a 0,09 €. m-3, mientras que, si se precisara desalar, este coste se multiplica por diez en la implantación y por cinco en la explotación. En caso de los usos que requieren de TRA, como los domiciliarios o algunos industriales, los costes serían de 185 a 398 €.m-3.d en implantación y de 0,14 a 0,20 €.m-3 en explotación. En la selección de tecnologías de regeneración, la capacidad del tratamiento en relación al coste es un indicador fundamental. Este trabajo aporta curvas de tendencia coste-capacidad que sirven de herramienta de selección frente a otros tratamientos de regeneración de reciente implantación como son los MBR, u otros como la desalación de agua de mar o los trasvases entre cuencas dentro de la planificación hidrológica. En España, el aumento de las necesidades de agua de alta calidad en zonas con recursos escasos, aumento de zonas sensibles como puntos de captación para potables, zonas de baño o zonas de producción piscícola, y en ocasiones, el escaso terreno disponible para la implantación de nuevas plantas depuradoras (EDARs), han convertido a los MBRs, en una opción dentro del marco de la reutilización de aguas depuradas. En este trabajo, se estudia esta tecnología frente a los TRC y TRA, aportando igualmente curvas de tendencia coste-capacidad, e identificando cuando esta opción tecnológica puede ser más competitiva frente a los otros tratamientos de regeneración. Un MBR es un tratamiento de depuración de fangos activos donde el decantador secundario es sustituido por un sistema de membranas de UF o MF. La calidad del efluente, por tanto, es la misma que el de una EDAR seguida de un TRA. Los MBRs aseguran una calidad del efluente para todos los usos establecidos en el RD, incluso dan un efluente que permite ser directamente tratado por las unidades de desalación de OI o EDR. La implantación de esta tecnología en España ha tenido un crecimiento exponencial, pasando de 13 instalaciones de menos de 5.000 m3. d-1 en el 2006, a más de 55 instalaciones en operación o construcción a finales del 2014, seis de ellas con capacidades por encima de los 15.000 m3. d-1. Los sistemas de filtración en los MBR son los que marcan la operación y diseño de este tipo de instalaciones. El sistema más implantado en España es de membrana de fibra hueca (MFH), sobre todo para instalaciones de gran capacidad, destacando Zenon que cuenta con el 57% de la capacidad total instalada. La segunda casa comercial con mayor número de plantas es Kubota, con membranas de configuración placa plana (MPP), que cuenta con el 30 % de la capacidad total instalada. Existen otras casas comerciales implantadas en MBR españoles como son Toray, Huber, Koch o Microdym. En este documento se realiza la descripción de los sistemas de filtración de todas estas casas comerciales, aportando información de sus características, parámetros de diseño y operación más relevantes. El estudio de 14 MBRs ha posibilitado realizar otro de los objetivos de este trabajo, la estimación de los costes de explotación e implantación de este tipo de sistemas frente a otras alternativas de tratamiento de regeneración. En este estudio han participado activamente ACA y ESAMUR, entidades públicas de saneamiento y depuración de Cataluña y Murcia respectivamente, que cuentan con una amplia experiencia en la explotación de este tipo de sistemas. Este documento expone los problemas de operación encontrados y sus posibles soluciones, tanto en la explotación como en los futuros diseños de este tipo de plantas. El trabajo concluye que los MBRs son una opción más para la reutilización de efluentes depurados, siendo ventajosos en costes, tanto de implantación como de explotación, respecto a EDARs seguidas de TRA en capacidades por encima de los 10.000 m3.d-1. ABSTRACT The reuse of treated effluent has always been an option in places where a situational or structural water deficit exists, whether regulatory and/or planning efforts are completed or not. The need arises from the demand of a sector, commonly agricultural irrigation, which benefits of this new resource. Within the EU, Spain is ahead in the annual volume of reclaimed water, and is among the top ten countries at a global scale. The regulation of this practice through the Royal Decree 1620/2007 has helped to incorporate the water reuse to the hydrological plans as a part of the programme of measures to mitigate pressures such as surface or ground water extraction, or environmental improvements preventing discharges. The object of this study is to gain an overview of the state of the water reuse in Spain, the different scenarios and approaches to this activity, the development of the legal framework and its enforceability, together with the treatments that achieve the quality levels according to the current law, broken down by applications. Additionally, a cost analysis of technologies and regeneration treatment lines for water reclamation is performed, whereas the regeneration treatment is located after a wastewater treatment or other options such as membrane bioreactors (MBR). To develop the abovementioned objectives, the state of water reuse in Spain is studied by means of a database designed to encompass all aspects of the activity: data from the wastewater treatment plants (WWTP), from the water reclamation plants (WRP), the use of reclaimed water, treated water and reclaimed water annual volumes and qualities, facilities and applications, geographic references, technologies, regeneration treatment lines, etc. The main data providers are the River Basin authorities, through the concession or authorization for water reuse, (sanitary and wastewater treatment managers from the territorial governments, local governments, Hydrological Plans of the River Basins and field visits to the main water reuse systems. Additionally, a review of different plans and programmes on wastewater treatment or water reuse is done, aiming to put the development and consolidation process of this activity in the different regions of Spain in perspective. An inventory of 322 reuse systems and 216 regeneration treatments has been gathered on the database, where the most extended regeneration treatment line was sand filtration followed by hypochlorite disinfection, even though recently it is being replaced by physical–chemical treatment with a lamella settling system, depth sand filtration, and a disinfection with ultraviolet radiation and hypochlorite as residual disinfectant, named conventional regeneration treatment (CRT), and another treatment that may include a membrane process, named advanced regeneration treatment (ART), to adapt to legal requirements. Agricultural use is the most extended, accumulating 70% of the reclaimed demand, estimated at 408 hm3, even though the expected total capacity of WRPs for 2015, after the implementation of the National Water Reuse Plan (NWRP) is three times higher. According to the development of the water reuse legal framework, there were pioneer areas where competent authorities developed different quality and use recommendations for this new resource. Agricultural use and golf course irrigation in touristic areas were the first two uses with recommendations and even legislation. The initial lack of common legislation for water reuse at a national or European level created some doubts which affected the implementation of water reuse, both from a planning and a licensing point of view. Currently there is still a lack of common international legislation regarding water reuse, technologies and applications. Regarding agricultural use, the model recommendations at a global scale are those set by the World Health Organization published in 1989, and subsequent reviews and extensions about risk prevention (WHO, 2006). These documents combine wastewater treatments with basic regeneration treatments reinforced by good practices based on different levels of protection to avoid deleterious health effects. Another relevant legal reference for this practices has been the Environmental Protection Agency of the US (USEPA, 2012), or those published by the State of California (Title 22, 2001). These establish indicator targets and maximum thresholds where regeneration treatment lines are responsible for the final quality according to the different uses. During 2015, the ISO has worked on a document aimed at urban use, where the possible parameters to be monitored together with risk prevention have been studied. On the other hand, the European Commission has been promoting the reuse of treated effluents within the Common Implementation Strategy of the Water Framework Directive, mainly through the work of the Programme of Measures Working Group. Within this context, the publication of a recommendation guide during 2016 is intended, as a useful tool to fill in the legal gaps of different Member States on the matter. The Royal Decree 1620/2007, where the water reuse regulation is set, resembles the principles of the USEPA more closely, even though the EU shows a tendency to prioritize risk assessment by establishing tolerance levels and thresholds according to socioeconomic conditions of the different countries, without going into details of indicators, maximum thresholds or treatments. In contrast, in the US law, regeneration treatments are indicated, while in the Spanish legislation, the only recommendations to this respect are compiled in a non-compulsory guide. Therefore, there is no regulation on the different treatment lines used to achieve the required quality standards, giving room for inappropriate practices in this respect. This is the case of disinfection, where the use of hypochlorite may produce harmful byproducts. In the recommendation Guide for the application of the Royal Decree (RD), published by the Ministry of Agriculture and Environment (MAGRAMA) in 2010, clarifications of typical issues that may arise from the application of the RD are given, as well as basic technical parameters to consider in reuse setups, or good practices according to final use. Even so, the RD still presents difficulties in its application and requires a review on issues such as the sampling frequency of current quality parameters or even the omission of nematode eggs indicator, which have been shown to be absent after CRT. In this regard, there is a global tendency to employ water reuse for drinking water, including indicators for the presence of viruses and protozoans, or to include certain technologies such as membranes or advanced oxidation processes to tackle problems like emerging pollutants. Another of the objectives of this study is to provide different regeneration treatment lines to meet the quality requirements established in the RD 1620/2007 broken down by applications, and to estimate establishment and operational costs. This proposal has been based on what is established in the above mentioned Guide and NWRP. The proposed treatment typologies are divided in treatment trains with desalination, like reverse osmosis or reversible electrodialisis, and those that lack this treatment for brackish water. This separation is done due to coastal facilities, where sea water may permeate the collecting pipes, rising salt contents in the wastewater, hence limiting certain uses. To develop this objective a study of the most common treatment units set up in Spanish WRPs is conducted in terms of treatment train reliability to obtain an acceptable relationship between the required quality and the capital and operational costs. The CRT has an establishment cost of 28 to 48 €.m-3.d and an operation cost of 0.06 to 0.09 €.m-3, while, if desalination was required, these costs would increase tenfold for implementation and fivefold for operation. In the cases of uses that require ART, such as residential or certain industrial uses, the costs would be of 185 to 398 €.m-3.d for implementation and of 0.14 to 0.20 €.m-3 for operation. When selecting regeneration treatment lines, the relation between treatment capacity and cost is a paramount indicator. This project provides cost-capacity models for regeneration treatment trains. These may serve as a tool when selecting between different options to fulfill water demands with MBR facilities, or others such as sea water desalination plants or inter-basin water transfer into a water planning framework. In Spain, the requirement for high quality water in areas with low resource availability, the increasing number of sensitive zones, such as drinking water extraction, recreational bathing areas, fish protected areas and the lack of available land to set up new WWTPs, have turned MBRs into a suitable option for water reuse. In this work this technology is analyzed in contrast to CRT and ART, providing cost-capacity models, and identifying when and where this treatment option may outcompete other regeneration treatments. An MBR is an activated sludge treatment where the secondary settling is substituted by a membrane system of UF or MF. The quality of the effluent is, therefore, comparable to that of a WWTP followed by an ART. MBRs ensure a sufficient quality level for the requirements of the different uses established in the RD, even producing an effluent that can be directly treated in OI or EDR processes. The implementation of this technology in Spain has grown exponentially, growing from 13 facilities with less than 5000 m3.d-1 in 2006 to above 55 facilities operating by the end of 2014, 6 of them with capacities over 15000 m3.d-1. The membrane filtration systems for MBR are the ones that set the pace of operation and design of this type of facilities. The most widespread system in Spain is the hollow fiber membrane configuration, especially on high flow capacities, being Zenon commercial technology, which mounts up to 57% of the total installed capacity, the main contributor. The next commercial technology according to plant number is Kubota, which uses flat sheet membrane configuration, which mounts up to 30% of the total installed capacity. Other commercial technologies exist within the Spanish MBR context, such as Toray, Huber, Koch or Microdym. In this document an analysis of all of these membrane filtration systems is done, providing information about their characteristics and relevant design and operation parameters. The study of 14 full scale running MBRs has enabled to pursue another of the objectives of this work: the estimation of the implementation and operation costs of this type of systems in contrast to other regeneration alternatives. Active participation of ACA and ESAMUR, public wastewater treatment and reuse entities of Cataluña and Murcia respectively, has helped attaining this objective. A number of typical operative problems and their possible solutions are discussed, both for operation and plant design purposes. The conclusion of this study is that MBRs are another option to consider for water reuse, being advantageous in terms of both implementation and operational costs, when compared with WWTPs followed by ART, when considering flow capacities above 10000 m3.d-1.

Reduction of emerging micropollutants, organic matter, nutrients and salinity from real wastewater by combined MBR–NF/RO treatment

To study the possibility of producing better water quality from municipal wastewater, a membrane bioreactor (MBR) pilot plant with flat sheet (FS) and hollow fiber (HF) membranes coupled with another pilot plant equipped with nanofiltration (NF)/reverse osmosis (RO) membranes were operated to treat municipal wastewater from the wastewater treatment plant (WWTP) Rincón de León, Alicante (Spain). This study was focused on improving the quality of the permeate obtained from the MBR process when complemented by NF or RO stages with respect to salinity, organic matter and nutrients. Furthermore, the removal efficiencies of 10 EMPs were evaluated, comparing the reductions achieved between the wastewater treatment by MBR (adsorption to sludge and biodegradation) and the later treatment using NF or RO (mainly size exclusion). The results showed that the high quality of water was obtained which is appropriate for reuse with salinity removal efficiencies higher than 97%, 96% for total organic carbon (TOC), 91% for nitrates View the MathML sourceNO3- and 99% for total phosphorous (TP). High removal efficiencies were obtained for the majority of the analyzed EMP compounds.

Biodiesel production by transesterification of sludge in supercritical conditions

In this study wastewater treatment plant (WWTP) sludge was subjected to a reactive pyrolysis treatment to produce a high quality pyro-oil. Sludge was treated in supercritical conditions in the presence of methanol using hexane as cosolvent in a high pressure lab-autoclave. The variables affecting the pyro-oil yield and the product quality, such as mass ratio of alcohol to sludge, presence of cosolvent and temperature, were investigated. It was found that the use of a non-polar cosolvent (hexane) presents advantages in the production of high quality pyro-oil from sludge: increase of the non-polar pyro-oil yield and a considerable reduction of the amount of methanol needed to carry out the transesterification of fatty acids present in the sludge.

Energy consumption in an urban wastewater treatment plant: the case of Murcia Region (Spain)

Of all the costs associated with the operation and maintenance of wastewater treatment plants (WWTPs), those associated with energy use tend to be the most significant. From this point of view, it is hence logical that energy efficiency and saving strategies should be one of the current focuses of debate amongst those involved with the management of WWTPs. The present study's objective is to determine the correlation between size and energy consumption for a WWTP. To this end, 90 WWTPs currently in service were analysed and their energetic impact quantified in terms of kWh/m3 of water treated. The results obtained demonstrate that energy consumption ratio increases as the size of WWTPs decreases, either in terms of treatment volume or population equivalent served.

The effect of electricity tariffs over the operating costs of the Spanish wastewater treatments plants

Given the complex structure of electricity tariffs and their steady growth in Spanish, we've studied its effect over the operating costs of the wastewater treatment plants (WWTP), concluding that in the last three years the revisions of electricity rates have meant increases in electricity costs of 64.5% in the rate 3.1.A and 79.1% in the rate 6.1. This has caused the cost of electricity, which was the most important, has increased from a 44% of total operating costs in the year 2009, to more than a 56% in the year 2012.

Characterization of residual soil used for infiltration of reclaimed water

The effects of climate change and the growing demand for water for domestic, industrial, agricultural and recreational activities have been led the use of treated wastewater (reclaimed water) for such applications. The artificial recharge of aquifers with treated wastewater can be an alternative way for restoring underground water volumes that can be used for satisfying some activities, particularly in water shortage areas or where their quality is not suitable for use. After a two-year monitoring period in the Vila Fernando WWTP (Guarda, Portugal), the characteristics of the treated effluent suggest that it could be used for infiltration for aquifer recharge. A multi-criteria analysis based on GIS was developed for site location of infiltration sites. The procedure has involved the combination of six thematic maps and environmental, technical and economic criteria, over an area of 6687.1 ha. About 6.4 ha were selected for suitable sites for infiltration and one of these sites (Quinta de Gonçalo Martins, Guarda) was selected for collecting soil samples. The characterization of the soil indicates that is favorable to the infiltration of treated wastewater for artificial recharge of aquifers.

Effects of phosphorus on the growth and nitrogen fixation rates of Lyngbya majuscula: implications for management in Moreton Bay, Queensland

Significant acetylene reduction and therefore N-2 fixation was observed for Lyngbya majuscula only during dark periods, which suggests that oxygenic photosynthesis and N-2 fixation are incompatible processes for this species. Results from a series of batch and continuous-flow-culture reactor studies showed that the specific growth rate and N-2 fixation rate of L, majuscula increased with phosphate (P-PO4) concentration up to a maximum value and thereafter remained constant. The P-PO4 concentrations corresponding to the maximum N-2 fixation and maximum growth rates were -0.27 and -0.18 muM respectively and these values are denoted as the saturation values for N-2 fixation and growth respectively. Regular monitoring studies in Moreton Bay, Queensland, show that concentrations Of P-PO4 generally exceed these saturation values over a large portion of the Bay and therefore, the growth of the bloom-forming L, majuscula is potentially maximised throughout much of the Bay by the elevated P-PO4 concentrations. Results from other studies suggest that the elevated P-PO4 concentrations in the Bay can be largely attributed to discharges from waste-water treatment plants (WWTPs), and thus it is proposed that the control of the growth of L. majuscula in Moreton Bay will require a significant reduction in the P load from the WWTP discharges. If the current strategy of N load reduction for these discharges is maintained in the absence of substantial P load reduction, it is hypothesised that the growth of L, majuscula and other diazotrophs in Moreton Bay will increase in the future.